Search Documents

By Creasey JW, Rixon KL

Underground mining in the Bowen Seam has shown that the majority of outbursts have co- incided with faults, igneous dykes and sills, stone roof rolls or some combination of these. The coal measures are deformed principally by N- S trending, easterly dipping thrusts presumed to he associated with the major, reverse Collins- ville Fault. The old Collinsville State Mine records suggest that thrusts and strike-slip faults have been common sites of outbursts. In contrast, normal faults have not been outburst- prone. Detailed geological mapping in Bowen No. 2 Colliery 53 east and west panels has been carried out in the hanging wall of a thrust zone of 6.1 m throw. The associated sheared coal has been defined and several fracture sets delin- eated. Sheared coal can be observed up to 170 m from this thrust zone, but this is dependent on the vitrinite content of the upper seam section worked. Fvidence indicates that outbursts have crnrroJ only in extremely sheared coal. Curious spherical- to cylindrical-shaped c,,.31 ohjects ("apples" and "rods") are related to the deformation in the vicinity of the thrust zone. The frequency of rods rises from 0 at 31)0 m, to I per metre at 150 m, and to 2.5-8.5 per metro at 10 m from the -

Jan 1, 1980

The preferred alternatives in heap design and their motivation are identified as- -normal heap leaching, to be generally applied wherever possible, - flooded vat leaching, to be appliedwhere wetted ore lacks adequate cohesion or if limited space necessitates it,- thin layer leaching, to be applied where deleterious vat chemistry necessitates it.A number of the following features would probably be incorporated in the optimization of normal local heap leach operations- pre-cyanidation - pre-agglomeration - retaining walls- staged (counter-current) heap treatment- control of calcium levels- reduced pH and trickler irrigation

Jan 1, 1984

By Agrawal A, Joshi A

Mochia mine, in culmination of depillaring operations, fired India's largest underground pillar blast consuming 145 tonnes of explosive and yielding 0.55 million tonnes of ore in June 1994. To protect main mine structures (situated at a distance of 250 to 350 m from the blast site) from resultant ground vibrations, the charge per delay was restricted to 2300 kg. The post-blast observations revealed that no damage was caused to these structures. However, the damage assessment survey of the mine workings situated in close proximity revealed a general trend in consonance with the distance from the blast and found to be well correlated with peak particle velocity.

Jan 1, 1995

By Dunlop JSF

A description of general mining proced- ures and tyre maintenance practice is given with particular reference to tyre mainten- ance facilities and record keeping at Groote Eylandt. Experience with tyre wear on Wabco 85C rear dump trucks is then outlined, concen- trating on wheel camber, wheel alignment, truck speed, tyre pressure, loading and haul road design. T T.1TUnilhTPTTnAT The Groote Eylandt Mining Company Pty. Limited mines and beneficiates sedimentary manganese ores from a series of orebodies occurring in the western part of the island. The island is one of a group on the western side of the Gulf of Carpentaria, about 50 kilometres from the Arnhem Land coast and about 650 kilometres from Darwin. Whilst capacity of the mine is presently 2.3 mil- lion tonnes of product per annum, current production has been reduced to just more than half this figure, due to a general mar- ket recession.

Jan 1, 1982

There are many variables in a flotation concentrator, some of which are outside the actual flotation stage, which affect metallurgical performance. The number of such variables which can now be measured on a continuous basis has increased significantly over the past 20 years. They can be broadly classified under the headings of physical, chemical, and elemental. In this paper reference is made to a number of such variables, and comment is made on the state of the art in their measurement. Although not confined to development in Australia, particular reference is made to the considerable Australian contribution in this area of Technology.

Jan 1, 1984

By P H. Warton

It is proposed to construct a gold extraction plant at Matatoki, near Thanes. Ore to be processed at the mill will come from reopened and enlarged underground mines north of Thanes. The project has been described in some detail in environmental impact reports (Worley Consultants Ltd 1984, 1987), and is now at an advanced stage in terms of obtaining the required statutory approvals.

Jan 1, 1987

By H Kurth

Oyu Tolgoi copper and gold mine in the southern Mongolia holds mineral resources that make it one of the largest known copper and gold deposits in the world. The project is operating an open pit mine on the near surface of Southern Oyu deposit and developing underground block-caving mine at the Hugo Dummet North where 80 per cent of total resources exists. Oyu Tolgoi (OT) commenced open pit mining in 2011 and implemented an industry standard blasthole sampling, and ordinary kriging grade control estimation with block-out process. Since 2017, grade control improvement projects have successfully completed that have led to the implementation of current, improved grade control system. Geological model is updated by blasthole logging on Leapfrog® and used for daily grade estimations. GC estimation is proceeded solely on Vulcan® by running Lava script and integrating with a relational database. Combination of block-out procedure produces GC model which is updated in Vulcan® and as well as in the database simultaneously. Switching to the integrated database eliminated many manual processes such as importing and exporting data and enabled access to the database anytime, anywhere and from any device. Thereby, these improvements allowed to increase an efficiency, create a comprehensive reconciliation system and reduce operational risks. We are looking forward to expanding applications of integrated grade control data stored in the database. This paper outlines how the grade control system was developed at OT’s open pit mine, and how it is integrated into the short range mine planning, mine reconciliation workflow and ultimately enabled development of various automated reporting systems.

Mar 22, 2022

The fluorspar deposits at Okorusu, Namibia are closely related to an alkaline igneous ring complex of late Cretaceous age (125¦7 Ma). The fluorite ores consist of relatively fine-grained purple replacement fluorite and subsequent coarser-grained purple and green vug-filling fluorite crystals. Homogenisation temperature measurements for 38 primary fluid inclusions shows that main stage purple to green fluorite crystals were deposited over a temperature range from 166¦C to 144¦C, and minor late yellow fluorite was deposited at lower temperatures from 132¦C to 128¦C. Homogenisation and freezing temperatures measured for 18 primary fluid inclusions shows that the fluorite-depositing fluids were less saline than Mississippi Valley-Type (MVT) ore fluids and overlap the lower temperature range of fluids that deposited epithermal ore deposits. Mining in three open pits (A, B and C) at Okorusu has gradually provided exposures which reveal that the fluorite orebodies have been emplaced primarily by the preferential replacement of carbonatites. Evidence for the replacement of carbonatite includes: replacement remnants of carbonatite within the fluorite ores; goethite pseudomorphs after the carbonatite minerals, pyroxene, pyrrhotite and magnetite, which are disseminated in the fluorite ores; andpartial replacement by fluorite of a large sill-like carbonatite body in the A pit. Electron microprobe analyses of minerals in unreplaced portions of the carbonatites show that their mineralogy consists of titaniferous magnetite, diopside pyroxene, apatite, biotite and calcite. Magnetite contains 6.97 per cent to 10.46 per cent TiO2, averages 8.44 per cent TiO2, and has an average V2O3 content of 0.35 per cent. At high magnifications under the scanning electron microscope (SEM), the magnetite shows abundant fine ulv÷spinel exsolution lamellae arranged in a cloth texture. Apatite contains moderately high fluorine contents that range from 3.21 to 5.0 per cent and average 4.2 per cent, and apatite crystals range in total rare earth oxides from 1.7 per cent to 2.61 per cent. Pyroxenes in the carbonatites are iron-rich diopside, and they contrast to pyroxenes in the fenites that are aegirine-augite. All of the microprobe analyses for mica crystals in the carbonatites give biotite compositions. Microscopic examination of fluorite concentrates from Okorusu provides mineralogical information important to the resolution of beneficiation problems. Fluorite ores that are related to carbonatites are typically accompanied by phosphorus benefication problems. The cause for the presence of phosphate in some of the Okorusu fluorite concentrates is a function of the presence of binary locked fluorite-apatite particles. The fluorite ores have also replaced marble locally in the A pit, especially along the A band in the B pit, and dominantly in the orebody proposed for the new C pit. Those ores are characterised by fine grain sizes, faint remnant bedding, lack of carbonatite mineral pseudomorphs and local presence of remnants of unreplaced marble. Concentrates derived from those fluorite ores are devoid of phosphorus, but commonly have elevated silica contents due the presence of free quartz. Carbonatite and marble were preferentially replaced by fluorite because the calcite was readily soluble in the presence of the fluorite-depositing fluids and the dissolution of calcite provided calcium for the formation of fluorite. 

Jan 1, 2008

By Blom MS

Two well-developed styles of mineralization occur in the Nevados del Famatina mining district, Famatina ranges, La Rioja province, Argentina. Porphyry molybdenum- copper-gold mineralization and high level acid sulphate alteration/mineralization (Nevados del Famatina) are related to intrusion of the Pliocene Mogote rhyodacite porphyry complex. High sulphidation epithermal mineralization (La Mejicana) is developed peripheral to the Nevados del Famatina deposit. Both are hosted mainly by the Ordovician Negro Peinado metapelites.At Nevados del Famatina, five mineralized fracture events have been identified and correlated with four distinct alteration assemblages. Stage I (barren quartz) and stage II (molybdenite¦sphalerite¦pyrite) mineralization are associated with a K-silicate alteration assemblage of K-feldspar+biotite+quartz+magneti te¦ilmenite¦anhydrite. Stage III (bornite+pyrite+sphalerite+molybdenite ¦chalcopyrite¦idaite) and stage IV (chalcopyrite+pyrite +sphalerite+gold¦tennantite-tetrahedrite) mineralization are related to a quartz-sericite assemblage of quartz +phengite+illite+pyrite+rutile. Stage V mineralization is divided into two substages. Stage Va (chalcopyrite +pyrite+sphalerite¦ tennantite-tetrahedrite ¦ tellurides ¦ gold ¦enargite¦famatinite¦stibnite¦molybdenite) is related to a sericite-clay assemblage of quartz+illite+kaolinite ¦montmorillonite¦alunite. Alunite-kaolinite alteration (alunite+pyrophyllite+kaolinite+ aluminum - phosphate -sulphate minerals ¦illite¦fluorite¦corundum¦anhydrite) occurs in the upper part of Nevados del Famatina associated with the later stage Vb (quartz+famatinite +chalcopyrite+covellite + chalcocite ¦ marcasite ¦ enargite ¦ luzonite¦sphalerite¦melnikovite) mineralization.

Jan 1, 1990

By Player R. L

Measurements of the rate of PbO reduction from high lead metallurgical slags were made under laboratory conditions using graphite, a CO-50%CO2 gas mixture and metallic iron as reductants. The results show a transition in rate-controlling step at low PbO contents (i.e. 6 wt.% PbO). At medium to high PbO contents in the slag, the reduction rate was found to be strongly affected by the slag chemistry, temperature and reductant type. The effect of stirring and hence mass transfer in the slag phase on the reduction rate of PbO was found to be insignificant at medium-high PbO contents. Attention is drawn to the importance of chemically controlled reaction rates at the slag-gas interface. Parallels between these results and test work on a 5 tph scale have been briefly drawn.

Jan 1, 1989

By M B. McKevitt, W J. Shaw

The main task of grade control on a daily basis is to define the material that should be mined to a destination under various categories. This can be determined by grade, lithology, quality and blending criteria. In the case of multi-element deposits or deposits with various blending or other processing criteria the optimum selection of ore block boundaries can be quite complex. In every case the balance between ore loss and dilution must be considered when designing the ore block boundaries and this becomes a risk-based decision when using the conditional simulation model. The use of such systems allows grade control to meet specific targets, such as budget tonnages and grades and blended product specifications. Two case studies are presented: the Prominent Hill copper/gold mine and the Rapu Rapu zinc/copper mine. Mining is based on a rational grade control strategy involving a number of factors, including strong geological control, advanced geostatistical approaches, such as conditional simulation, and optimisation of the ore blocking to meet production requirements. This provides an objective, transparent and repeatable grade control strategy.

Jan 1, 2009

By H Kurth

High specification Prompt Gamma Neutron Activation Analysis (PGNAA) has been successfully applied to conveyed flows at iron ore operations since 2002 to representatively measure ore quality for improved quality management and process control. While the PGNAA technique has changed little since that time, significant improvements have been made in measurement capability. Elements previously unable to be measured well or at all using this technique are now measurable and one of these is phosphorus. Aluminium and magnesium are also key elements in addition to calcium and silicon in determining sinter basicity in ironmaking. Other elements measured routinely in iron ores include iron, carbon, potassium, sulfur and manganese. The benefits of representative measurement cannot be overstated as iron ore mining operations in South Africa, Europe, Australia, Asia and the Americas have discovered. The technology is applicable to any conveyed flow where elemental analysis in real time assists with quality management, from raw materials in ironmaking through to scrap steel in steelmaking and coal quality for coke-making. Major benefits are realised when raw material processing is optimised and this often includes diversion of material meeting a required quality so it can bypass unnecessary processing. This includes waste rock which can be diverted from a plant feed stream in 30 sec increments or ore that meets product quality being diverted to bypass beneficiation. Analysers are successfully utilised to identify ore types that assist with upgrade optimisation in jig plants; measuring feed, product and discard flows to also account for metal content. Product flows to stockpiles help manage production flows and stockpile qualities for different products and assist in blending ores into trains or ships to confirm specification compliance. Technologies can be used in magnetite processing but are predominantly used in hematite and goethite ore processing operations. The paper details examples of the above applications at various operational sites providing estimates of economic benefit as well as operational improvements.

Sep 18, 2023

The grades of alluvial ore deposits are low compared with grades of hard rock mining. This factor, combined with other parameters of irregular distribution of particles, bedrock irregularities, size of particles, nugget effect, ore characteristics, and wet horizons, combine to place alluvial deposits among the most difficult to evaluate, and on which to establish an ore reserve with a high degree of confidence. With increased geological input, correct selection and implementation of sampling method, due regard to sample representativity and process design, these confidence levels can be achieved.

Jan 1, 1987

By Lunardi P, Pelizza S

The link between the Lecco bypass and major road SS36 (Italy) requires the construction of a double two-way tunnel (through the mount San Martino carbonatic massif). The tunnel excavating section is about 90 sqm through mount San Martino carbonatic rocks. The mountain sides are unstable and are often the scene of large collapsing landslides (tens of thousand cubic metres). The tunnels are very close to the mountain sides. The use of blasting induces vibrations which may reach the Lecco built-up area. With a view to avoiding such dangers the excavating operations were carried out in two successive stages: - opening a pilot tunnel, whose section is about 10 square metres, by a full face TBM to eliminate the more intense vibrations which are generated by the first opening charges; - successive enlargement by blasting.

Jan 1, 1987

Asbestos is a commercial term applied to fibrous varieties of several minerals, the properties of which are not generally appreciated by the majority of geologists. A thorough knowledge of these properties and of the uses of asbestos is of fundamental importance in the assessment of the economic value of an occurrence of asbestos. The varieties of asbestos that are used predominantly by the manufact- urers of asbestos products are chrysotile, crocidolite and amosite but chrysotile constitutes 95% of the world's usage. It is the properties of high tensile strength, 'heat resistance and large surface area that make chrysotile asbestos the most acceptable of the mineral fibres. There are no known exploration aids, other than direct visual inspec- tion of outcrops in ultrabasic environments, that could be used in the exploration of chrysotile asbestos. The surface exploration of an occurrence of chrysotile asbestos is relatively routine, though it lends itself to a unique form of bulk sampling by the use of a twelve inch diameter diamond drill core. The laboratory assessment of the prop- erties of the actual fibre requires specialized techniques and tests to assess not only the amount of fibre present but also its length distri- bution, inherent strength, filterability, dust content and other prop- erties. The way a fibre reacts to milling will determine what milling process- es must be implemented to ensure a product that is acceptable to the asbestos product manufacturing industry.

Jan 1, 1971

The Bowen Basin coal field is an important energy resource. A relatively small proportion is avail- able by open cut operations. Responsible men throughout the world have warned of the need to increase coal research immediately. Because energy is still available in abundance these warnings have not been heeded in Australia. The characteristics of the Bowen Basin coal make it a fairly difficult underground mining proposition and a significant research effort is required to solve the problems likely to be encountered. Both industry and government have responsibilities in the economic recovery of the maximum proportion of the resource and jointly funded research administered by existing organisations should be inaugurated forthwith.

Jan 1, 1976

By B Ghahreman‐Nejad, M Munro

Design of embankment dams often requires seismic analyses, or an assessment of earthquakeinduced ground and dam movements. There are a large number of cases where earthquakes have triggered sliding and lateral spreading of embankments, resulting in excessive crest settlements. In some instances, liquefaction and embankment failure has occurred resulting in loss of containment. Hence, evaluation of the effects of earthquakes on embankment dams is a critical design aspect. This paper discusses the methods and the results of a seismic liquefaction assessment and deformation analyses of a tailings dam. The tailings dam consists of a perimeter earth core rockfill starter dam which has been raised using upstream construction methods. The embankment raises (formed by an upstream clay blanket and an all-in rockfill body) are constructed over the impounded tailings, which are potentially liquefiable. Extensive field and laboratory tests were undertaken to assess the liquefaction potential of the tailings, and also determine the material properties required for seismic stability and deformation analyses. Numerical modelling of seismic liquefaction and deformation was carried out using FLAC (Itasca 2016) to predict the magnitude and spatial variation of deformations that may lead to an uncontrolled release of tailings. Primarily based on a parametric assessment of UBCSand and Finn-Byrne constitutive models, the results of the analyses are presented and compared for evaluation.

Jul 1, 2021

Location & Permit Status Three major Mesozoic Tertiary basins exist along the continental shelf area of southeastern Australia, known as the Bass Strait area. They are the Gippsland (east of the longitude of Melbourne) Otway (west of Melbourne) and the Bass (underlying central Bass Strait between Victoria and Tasmania). The total area, both onshore and offshore, is approximately 100,000 square miles. In March 1960, the Broken Hill Pty. Co. Ltd. acquired exploration title to the continental shelf areas of the Gippsland, Bass and Otway basins from the States of Victoria and Tasmania. The title to that part of the Otway Basin in South Australian waters was granted in July, 1961. Other exploration permits, being 8 miles wide in Gippsland, held by Woodside :E.) Oil Co. N.L., and 15 miles wide along the southwest coast of Victoria, held by Mobil-BP-Interstate Oil (Frome-Broken Hill Co. Pty. Ltd.), were in existence prior to granting the B.H.P. title. Subsequently, Shell, B.H.P., Esso and Magellan have been granted title to the remaining areas of the continental shelf in the basins under discussion. In three separate agreeme negotiated between 1964 and-1966, Esso obtained farm-in rights to B.H.P.'s Gippsland, Bass and Ott' Permits.

Jan 1, 1970

By Bayly MG, Harris JA

The current operational practice at the Territory Enterprises Pty, Limited uranium oxide plant,, and some aspects of researc$ and development work at Rum Jungle are outlined with pertinent comments on some overseas practices.

Jan 1, 1968

By Richardson G. W, Yap L. C

Friction rock stabilisers (FRS) are steel-based, thin-walled tubular ground reinforcement widely used in underground mines in Western Australia. Following installation these stabilisers are subject to corrosion which may reduce the load carrying capacity and lead to unexpected ground falls. Although corrosion has been recognised as a common occurrence, particularly under aggressive mine water and mineral conditions present in underground mines, the knowledge of the effects of corrosion on the mechanical behaviour of FRS is limited. The Department of Minerals and Energy of Western Australia has conducted a laboratory based program of studies to investigate the effect of corrosion on the mechanical properties of FRS. The studies have focused on the effect of corrosion on tensile strength of FRS and frictional resistance along the interface between FRS and the drillhole wall. The results indicate that under certain conditions corrosion damage can significantly reduce the effectiveness of FRS.

Jan 1, 1996