Search Documents

By Whiteley M, Robinson T, Vernon B

The Western Australian gold industry has approximately 100 operating plants, mainly CIP/CIL. The nature of the State's rapidly expanding gold industry gave rise to concerns over management of the cyanide hazard, in that most plants are remote from major population centres, have a workforce with a high turn over and use highly saline process water. Approximately 4,500 workers in the industry have the potential to be exposed to cyanide in the course of their normal work.This paper outlines the risk management strategy developed by Government and industry to monitor atmospheric HCN gas in the work environment and the role of continuing education and training along with regular site inspections by Department of Mines Inspectors.

Jan 1, 1990

By Jin C, Shuyi L, Yuanbiao Z

This paper describes the structure, performance, principle and effectiveness of a new laboratory type of composed-forces field separator utilising the composition of the magnetic force, vibrating force, pulsating force, gravity and fluid-viscous force etc to separate fine feebly magnetic valuable minerals. Compared with the pulsating high gradient magnetic separator, this separator possesses unique advantages of higher enrichment ratio and higher recovery of the magnetic component.

Jan 1, 1993

By J Zhang, O Ostrovski, C Zhang D Cai, Q Wang

The conventional CaO-SiO2-based mould fluxes are not suitable for high-Al steel casting because of the strong reaction between silica in the flux and aluminium in the steel strand. In the process of casting of high-Al steel, flux composition changes; with the decrease of the silica concentration and increase of alumina. Knowledge and understanding of the effect of the Al2O3/SiO2 ratio on flux structure and properties are useful for flux design for the high Al-steel continuous casting. This paper investigated the effect of the Al2O3/SiO2 ratio on structure, viscosity, phase composition of fluxes quenched at different temperatures and heat transfer of CaO-Al2O3-SiO2-B2O3-Na2O-Li2OMgO- F fluxes. It was found that flux melting temperature increased with the increase in Al2O3/SiO2 ratio. Viscosity of the flux melts increased significantly with the increase of the Al2O3/SiO2 ratio from 0.7 to 1.2, reaching the maximum value, and then decreased with further increase of the Al2O3/SiO2 ratio. Raman spectroscopy analysis revealed that the change of the Al2O3/SiO2 ratio led to the change of aluminate and silicate structural units. The turning point for viscosity was attributed to the change in the degree of flux polymerisation. X-ray diffraction (XRD) analysis showed that increasing Al2O3/SiO2 ratio increased crystallisation tendency of the fluxes. Heat transfer measurement by infrared emitter technique (IET) revealed that increasing Al2O3/SiO2 ratio led to the decrease in heat flux which is correlated well with the increased crystallinity of the flux. The results suggested that the flux with Al2O3/SiO2 ratio 4.3 is the best candidate among the studied CaO-Al2O3-based mould fluxes for casting of high-Al steel.

Aug 21, 2024

By Filmer AO

In contrast to the '50s and '60s, the period of the '80s and '90s seems likely to have low growth in demand but much greater levels of technological change. In such a climate there will be pressure on costs, productivity will continue to rise and competitiveness will be closely associated with maintenance of the most effective technology. The penalties for inappropriate investments, whether short sighted or mistakenly based on a particular view of the future, will be greatly enhanced. Accordingly, there will be a need for significantly improved anticipation of technical change and thus for better planning. Study of the funding and direction of the world's R&D effort can provide a useful input to the planning processes within industries and individual firms. Such a study also suggests some insights into the characteristics of those countries which have achieved substantial growth and high standards of living over the past two decades. These characteristics may offer significant reminders for our own development. The particular implications for the Australian minerals industry include the need for direction that is sensitive to changing market requirements and customer practice. This is not simply "more of the same." In particular it appears essential for both basic and applied R&D to provide a sound basis for the purchase and ongoing development of the new technology required to achieve international Competitiveness.

Jan 1, 1986

In contrast to the '50s and '60s, the period of the '80s and '90s seems likely to have low growth in demand but much greater levels of technological change. In such a climate there will be pressure on costs, productivity will continue to rise and competitiveness will be closely associated with maintenance of the most effective technology. The penalties for inappropriate investments, whether short sighted or mistakenly based on a particular view of the future, will be greatly enhanced. Accordingly, there will be a need for significantly improved anticipation of technical change and thus for better planning. Study of the funding and direction of the world's R&D effort can provide a useful input to the planning processes within industries and individual firms. Such a study also suggests some insights into the characteristics of those countries which have achieved substantial growth and high standards of living over the past two decades. These characteristics may offer significant reminders for our own development. The particular implications for the Australian minerals industry include the need for direction that is sensitive to changing market requirements and customer practice. This is not simply "more of the same." In particular it appears essential for both basic and applied R&D to provide a sound basis for the purchase and ongoing development of the new technology required to achieve international Competitiveness.

Jan 1, 1986

The Circum-Pacific is defined to include back arcs and continental areas of volcanism. Volcanoes must be regarded as dormant, if the time since their last eruption is less than about ten times the average interval between eruptions, even if they have not erupted for tens of thousands of years or longer. It is important to establish a complete history, over as long a period as possible, for varying volumes of eruptions. In order to assess risk, the average interval between eruptions should be calculated for each range of erupted vo4ume~, in orders of magnitude from about 10 m up to the maximum volume possible at each volcano. Eruptions are considered to consist of individual explosions, and are grouped into eruptive sequences, with the sequences grouped into overall cycles of activity. Frequency of eruption versus volume erupted is a linear relationship for most andesitic and basaltic volcanoes, but is often bimodal at rhyolitic volcanoes, 3 with a slower eruption rate above about 10 km. Worldwide, during the last 7000 years, there have been three known e~uptions with volumes of ejecta of > 100 km , a9d, since 1638 A.D., 7 with volumes > 10 km , and 48 with volumes > 1 km . Average recurrence intervals are about 71 years for eruptions of > 20 km , 39 years for those of > 10 km , and 7 years for those of > 1 km . Rough esti- mates can be made for larger volumes erupted. Mean intervals in the Circum-Pacific are about twice the length of those for the world as a whole. During the last 400 years, about 61% of the world's eruptions of > 1 km3 have taken place in this region.

Jan 1, 1987

By M Dunglison, P M. Cameron

Simultaneous mass-balancing of a mineral processing flow sheet results in adjustments to each data point that reflects the accuracy and precision across the full set of data. In this way, all the good work that goes into designing the sampling and analysis protocol for each sample point is leveraged in order to produce a æbetterÆ set of balanced numbers for every sample point in the circuit. Few operating plants employ whole of circuit balancing techniques to produce reported operating results. This situation is changing with the application of mass balancing technology which utilises redundant data for production accounting and metal reconciliation from product to ore source across multiple phases and multiple time periods. Mine and plant data can now generate credible information to improve productivity. Mine and plant personnel can now use consistent data sets for review and planning. Decisions based on balanced data can be made quicker and with increased confidence.

Jan 1, 2005

By A Melkumyan, M Balamurali

Geological domains describe the mineralisation state and stratigraphic location of different geological regions of mines. They play a very important role at the geological modelling stage as weight percentage of chemical elements information within each geological domain is assumed to be correlated while information coming from different geological domains is considered uncorrelated. Having correct domain assignments to both the chemical assays and the 3D space of modelling is critical for building a reliable geological model of the mine.As standard practice significant effort is invested into the interpretation of the deposit and identification of the geological domains for the chemical assays and the 3D geological space. Despite these efforts, there are some chemical assays with ambiguous geological domain where the exploration assay domain and the block domain do not match. Incorrectly including a sample in the wrong domain can cause a large change in the predicted weight percentage of chemical elements estimation for that block. Therefore, the major challenge of grouping the spatially correlating weight percentage of chemical elements is how to determine which of these domains best fits these misclassified samples.This work proposes machine learning based autonomous technique for identifying to which geological domain (the exploration assay domain or the block domain) the misclassified sample belongs. The proposed methodology is based on Gaussian Process (GP) classification. The GP machine learning approach consists of training and inference stages. At the training stage the GP automatically learns the properties of different geological domains using the chemical assays with unambiguous domain assignment. Then, at the inference stage the GP makes predictions for the geological domains of the assays with ambiguous initial domain assignment.We tested the proposed technique by conducting a case study for an iron ore deposit located in Western Australia. The results demonstrate that the application of the proposed GP technique removes statistically significant deviations in the assay values in many regions: mineralised ore region, unmineralised region, highly weathered region and intrusive material that is highly variable. In this case study the proposed methodology autonomously identified the geological domains for more than 50 per cent of samples which are initially ambiguously classified. For the majority of the assays the GP predicted domain agrees with the geological domain assigned by the exploration assay.CITATION:Balamurali, M and Melkumyan, A, 2014. Automated identification of geological domains for exploration assays with ambiguous initial domain assignment in an iron ore deposit, in Proceedings Ninth International Mining Geology Conference 2014 , pp 99–106 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By Dobos SK, Gibson GM, Little TA, Sliwa R

Current studies, and analysis of previouslypublished data, have lead to a re-evaluation of the inclusion of the North D'Aguilar block within the "Gympie Province" in southeast Queensland. The metamorphic rocks are part of a Late Devonian(?)-Early Carboniferous subduction accretionary complex and are unconformably overlain by volcanic and coarse-grained clastic rocks of probable Early or mid-Permian age, as well as by Early to middle Triassic rocks of the Esk Rift. Metamorphic fabrics in the basement rocks include not only those that can be related to convergence, but also younger fabrics that may have developed during Late Carboniferous or Permian uplift and unroofing of the accretionary rocks. A predominance of basic schists, some of which are blue amphibole-bearing, and associated fine-grained pelagic and hemipelagic sediments in the Northern D'Aguilar block contrast with the siliciclastic-dominated sediments of most of the accretionary complexes of the New England Orogen. However the similarity of structural style, and metamorphic and igneous history, with adjacent basement blocks, and with other blocks throughout the New England orogen, suggests that the North D'Aguilar block simply represents deeper, probably underplated, levels of the same subduction complex. Uplift and cooling may have been accomplished by extensional faulting during Permian inception of the Esk rift, which flanks the block on the west.

Jan 1, 1990

By H R. Phillips

The ventilation and refrigeration design of underground mines is an important aspect, when new or existing mines are considered and places a great responsibility on engineers tasked to do so. The current trend for both local and international underground mines is to extend their search for valuable ore reserves deeper below surface. In South Africa, the predictions are that about 40 kt of actual gold still lies in situ, ready for extraction. As mines extend their search for minerals of economic value deeper and deeper into the earthÆs crust, ventilation and refrigeration aspects of such mines become more prominent than before. The planning and design of the required ventilation and refrigeration within these mines, over their expected lifetime is important including the practical implications of such designs. Technology changes and improvements need to be incorporated into ventilation and refrigeration designs, where possible and advances in this specialised field explored. This paper explores ventilation and refrigeration design aspects within the underground mine sphere. Aspects such as mining depth, virgin rock temperature (VRT), mining methods, and different cooling applications available including ventilation supply are reviewed in design applications. Heat generally becomes a significant aspect to counter in these mines and they are not always necessarily deep mines.

Jan 1, 2005

By Evans A. F

Arising out of the increasing demands for efficiency in modern ore-dressing operations has grown a requirement for fuller knowledge of the characteristics of the ore treated. In part, this is being met by improved methods of study of the mode of occurrence of the constituent minerals, and of the intricacies of their physical relationships.A typical instance of the need for such a study is the presence of some undesired mineral in a flotation concentrate or tailing, which may be due either to mechanical association through insufficient grinding, or to incomplete separation in the flotation operation.Again, with modern practice in fine grinding, which often requires that from 70% upwards of the ground ore shall pass a 200-mesh screen, it is obviously impossible to obtain data on comparative grinding efficiencies, for instance, unless there is adequate knowledge of the size-composition of the material passing the finest available screen.Studies like these can be made satisfactorily only after size-separation (which may be carried out conveniently by elutriation) and by actual visual examination with the aid of a microscope, and the minute size of the mineral grains to be examined has necessitated the development of a new technique of sizing and microscopic examination.

Jan 1, 1932

By S P. Suthers, J M. F Clout, J J. Campbe

An advanced technique for modelling hydrocyclone separation performance has been developed. This technique is based on the combined modelling of hydrocycloning parameters and ævirtualÆ iron ore feed. The virtual feed modelling was performed using a novel (in-house) software package called æRecognitionÆ, which uses data from optical image analysis to classify the particles in certain size fractions according to total iron content and calculates data for every grade class. These data include the average mineral composition and density of every liberation class in every size fraction. This information about every size fraction, representing the ævirtual feedÆ, was input to the mineral processing modelling package USIM PAC. The hydrocycloning process was then modelled for this virtual feed using the Plitt hydrocyclone model. Empirical calibration coefficients for the hydrocyclone model were calculated using an optimisation procedure in Excel. Pilot-scale hydrocyclone beneficiation experiments were performed on an iron ore blend, using different hydrocyclone pressures and per cent solids in the feed pulp. These experiments were modelled and the modelling results were compared with the experimental results. The new modelling approach enables prediction of the recovery of each mineral in the products, calculation of the total iron grade and recovery, and optimisation of iron ore beneficiation using hydrocyclones.

Jan 1, 2005

By C Slaughter, J C. Tien

Commonly held ideas about effective training have long emphasised the importance of realism. Realistic training builds better experience among the trainees and a better perspective on the training material, making training more effective. While great strides have been made in this realm for mine safety and mine rescue training there are still areas that can be improved. One possible area is the expanded use of a mine fire simulation program where the migration of gases and smoke can be realistically displayed in an emergency, and outcomes varied as different conditions are being simulated. The use of mine fire simulation software potentially allows for the creation of more realistic scenarios in that smoke advance rates can be measured and recreated in evacuation scenarios, or that gas readings in mine rescue training can be dynamically and realistically changed to show the effect that time has on the fire scenario.CITATION:Slaughter, C and Tien, J C, 2015. The potential use of mine fire simulation software as an enhancement for mine safety and mine rescue training, in Proceedings The Australian Mine Ventilation Conference, pp 285–290 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

Environmental leaching methods such as the toxicity characteristic leaching procedure (TCLP) test or the ASLP test are used to assess wastes including mining and mineral processing by-products. These tests were initially designed as regulatory tests simulating conditions in a co-disposal municipal landfill waste facility and do not allow leaching performance to be predicted in site specific scenarios. Further, the assumptions underlying these tests tend to define worst-case scenario leaching conditions for by-products from the mineral industry disposed of outside a co-disposal scenario.   Recently some characterisation leaching test methods have been issued as ISO/TS standards (ISO/TS 21268-3:2007 and ISO/TS 21268-4:2007) that aim to define the leaching performance of soil type wastes and to predict the leaching performance of these wastes over long time frames. In this preliminary work these standards are trialled for by-products from the mineral industry and the quality of information that can be obtained from them compared to TCLP/ASLP tests.   Where clear comparisons were possible, the TCLP/ASLP tests were typically found to extract a similar, or often greater, amount of component than (i) tests conducted at the same pH but without the acetate buffer or (ii) for test conditions aimed at simulating long-term leaching in an eluate defined by the waste type. While further work is required, the preliminary results indicated that the tests may provide reliable long-term estimates of leaching performance of wastes in soil types of variable pH and provide a suitable basis for long-term planning for optimal waste handling, treatment or even re-use.

Jun 1, 2010

By Kohra A, Shoji S

The amount of copper production by flash smelting process occupies about 17% (equivalent to 1.4 million t/year) of total free world production. In Japan, 650,000 tons of copper is produced annually by flash smelting. This is 65% of the gross copper production of Japan. To reinforce pollution control, promote energy saving, and enhance production efficiency by increasing the size of furnaces, conventional blast furnaces and reverberatory furnaces are being replaced with the flash smelters worldwide. The Ashio Smelter started copper production in 1884 and developed in association with the Ashio mine. In those days, the Ashio smelter produced copper by using the blast furnace process designed for the high-grade ore from the copper mine. At that time, this process was specialized in Japan. In 1956, for the first time in Japan, the Ashio Smelter introduced the flash smelting process developed by Outokumpu Oy of Finland (it is suitable for treating the copper concentrate, producing sulfuric acid and improving production efficiency). The flash furnace in Ashio, the first ever in Japan, had a capacity of 230 t/day for copper concentrate and was operated up to 1962. During this period, various operational troubles were solved, and further improvements were made; and, in 1962, a Furukawa-type flash smelting furnace was completed in Ashio. This improved version of a flash furnace had a capacity of 450 t/day. There was one flash furnace and one waste heat boiler, which were arranged in a unique pattern for that time. This furnace may be said to be the prototype of the present flash smelting process in the world.

Jan 1, 1987

By C A Heinrich, Jaques A. L, L A I Wyborn

Most orebodies have cross-sections of less than I km2 and hence do not offer a particularly large target for exploration. Fortunately, although in the geological record ore deposits are small and rare and result from the exceptional coincidence of certain geological processes, these processes are mappable on a much larger, district to regional scale and constitute a mineral system in which the ore deposit is the central feature. A mineral system can therefore be defmed as 'all geological factors that control the generation and preservation of mineral deposits, and stress the processes that are involved in mobilising ore components from a source, transporting and accumulating them in more concentrated form and then preserving them throughout the subsequent geological history'. The mineral system concept emphasises that for many ore deposit types, although economically viable mineralisation may only occur on a scale of say, hundreds of metres, the total system offluid-rock interactions that led to ore formation can extend over a distance of tens to hundreds of kilometres around the deposit. When mapped out, the total mineral system provides a far larger exploration target than the actual ore deposit itself. Important geological factors defining the characteristics of any mineralising system include: I. sources ofthe mineralising fluids and transporting ligands; 2. sources ofthe metals and other ore components; 3. migration pathway; 4. thermal gradient; 5. energy source; 6. a mechanical and structural focusing mechanism at the trap site; 7. chemical and/or physical traps for ore precipitation. Many of these factors individually are common through

Jan 1, 1994

By E Ben-Dor, D Bakun-Mazor, Y Ben-Ari

Determining the mechanical properties of rocks is important for various civil engineering fields, including the mining of raw materials for aggregates used in the construction and paving industries. Traditionally, the mechanical properties of rocks are obtained through in situ and laboratory tests during geotechnical surveys. However, these time-consuming surveys involve many resources. In contrast, hyperspectral remote sensing methods make it possible to identify the mineralogical composition and crystallographic structure of the rock; properties that control the mechanical properties of the rocks. In this work, we characterise the mechanical properties of carbonate rocks by using a hyperspectral sensor in laboratory conditions. We collected about 150 cylindrical samples of carbonate rock, with a wide range of strength values from several rock outcrops in Israel. We used a point spectrometer in the range of 0.4–2.5 μm and a spectral image sensor in the range of 3.0–12.0 μm, scanning the samples to obtain the signature of their light reflections and spectral emissivity. We then measured the samples’ density, porosity, water absorption, and uniaxial compressive strength (UCS). We used sophisticated data mining to find statistical relationships between the hyperspectral signatures of the samples and their mechanical properties. We used this data to identify the most dominant wavelengths for predicting mechanical properties. We found that the density, porosity, and water absorption of carbonate rocks could be confidently predicted based on spectroscopy data, while the UCS of the rock could also be predicted, but less significantly. The results of the study pave the way for the development of measuring tools for the mechanical properties of rock, based on non-destructive tests of quarrying materials.

Nov 29, 2022

The Crown Minerals Act 1991 has introduced some significant changes to the New Zealand mining industry, not the least of which relate to the ability of miners to obtain access to land to conduct mining activities. This paper briefly reviews the relevant provisions of the Crown Minerals Act dealing with access arrangements, considers some typical features of access arrangements and examines a number of areas where problems may arise.

Jan 1, 1992

By C A. Fleming, C J. Ferron, P T. OÆ

A new process is described which allows for direct recovery of base and precious metals (Au and PGMÆs) from sulphide concentrates or other feedstocks. The process was developed initially for application to ores or concentrates that are too low-grade for economic treatment by the conventional smelting and matte leaching process (for PGMÆs). It is now believed that the process may be widely applicable to a variety of materials including PGM concentrates containing high amounts of chromium or magnesium. Operating conditions have been identified under which gold, the PGMÆs and the base metals dissolve simultaneously in a pressure leaching autoclave. The product of this leaching process can then be treated by one of several flowsheets, of which the preferred will likely involve solid/liquid separation, followed by precipitation (or adsorption on activated carbon) of gold and the PGMÆs, followed by copper solvent extraction/electrowinning. Depending on the concentrations of nickel and cobalt, the copper raffinate would either be partially recycled to the autoclave to allow Ni/Co concentrations to build up, or it would proceed directly to a Ni/Co refinery. This paper deals with the pressure leaching process and the recovery of gold and the PGMÆs from the pressure leach product.

Jan 1, 2000

By J Rostami, D Tadic

While hard rock tunnel boring machines (TBMs) have an established track record in the tunnelling industry, accurate estimation of TBM performance for each specific project remains critical. Machine performance prediction is required to assist planning activities, including costing and schedule preparation, machine specification and effective planning of maintenance and repairs. In addition, monitoring machine performance during the construction period is required to assess and manage excavation progress, and to achieve optimal advance rates based on specific geotechnical conditions exposed during excavation. TBM performance analysis can also contribute to the development of more accurate performance prediction models for future applications. Rock mass characteristics play a dominant role in machine performance. This paper offers a review of the impact of rock mass characteristics on TBM penetration rates for two specific tunnelling projects. A discussion is provided on the results of statistical analysis of available field data, including geological back mapping, rock properties and measured rates of penetration (ROP). The analysis offers a comparison of the achieved and predicted ROPs to provide a better understanding of the influence of rock mass properties on the performance of hard rock TBMs. A new rock mass adjustment factor is introduced to enhance the accuracy of an existing prognosis model for use in jointed rock masses.

Jan 1, 2008