Search Documents

By Noller B. N, Mine F. J

Modem open cut and underground mining in the tropics inevitably expose partially weathered and unweathered rocks to oxygen and water, leading to weathering and the release of solutes and often acidity as well. Historical monitoring data can demonstrate these phenomena. Three case studies from open cut mines in the north of the Northern Territory illustrate the deterioration in quality of pond water receiving drainage from waste rock dumps. The potential for deterioration of water quality was not recognised in many mine Environmental Impact Statements prepared and accepted in the 1980s. The examples documented indicate the importance of adequately planning for this near inevitable process. Retrofitting a mine water management system to 'no' or minimal release can be very difficult and expensive, and may not be feasible, leading to downstream pollution. The characterisation of acid and solute production potential of ore and waste rock, and improved dumping strategies and water management are very important to minimise the environmental impact of mining in the tropics.

Jan 1, 1994

By K Luthbom, A Lagerkvist

According to the Swedish Environmental Protection Agency, the number of potentially contaminated sites in Sweden is approximately 40 000. The funding for remediation from the Swedish Government alone amounts to $A 60 - 80 M (300 - 400 MSEK) annually for the period 2003 - 2006. Uncertainties will arise when obtaining samples in field, preparing them in laboratories and analysing them. Different procedures give rise to varying errors. Using data for decision-making that does not truly represent the site could be fatal. Misclassification of soil could lead to unnecessary costs or to risks to human health and the environment. The total uncertainty of an environmental sample can be split into analytical uncertainty and sampling uncertainty. The analytical uncertainty is usually known and reported from routine analysis. The size of the sampling uncertainty is less well known. Hence, the question is how big are the sampling uncertainties for contaminated soil and how big is the analytical error compared to the total sampling error? A scrap yard and two landfills within a workshop area were investigated. An excavator dug trial pits and samples were taken with a trowel from the walls of the trial pits. Samples were put into plastic bags and taken off site for preparation and analysis using XRF. Sample preparation included drying and sieving. The samples were homogenised by kneading the sample bags prior to analysis. The sampling and sample handling were performed in an intuitively way without knowledge of sampling theory. However, Pierre GyÆs sampling theory was used for subsequent evaluation of the data from the site investigation. The theory defines seven sampling errors, which can be applied to sampling of soil. Some errors have a variance that can be calculated or at least estimated, while other errors can give some idea whether the bias is positive or negative. The total sampling error varied over three orders of magnitudes from sample to sample. The single largest contributor to the large variation in error was the contaminant level. When comparing the analytical error and the total sampling error the ratio varies more than three orders of magnitude.

Jan 1, 2005

By M Freeman

Significant improvements in the metallurgical performance at Pasminco Rosebery Mine have occurred over the last two years. Lead and silver recoveries have increased by more than ten per cent, lead concentrate grades are four per cent higher, zinc recoveries are up 1.5 per cent, and zinc concentrate grades have increased by two per cent. These impressive results have not occurred through the application of some new wonder reagent, but through the application of some fundamental metallurgical principals. The basic premise applied during this study was that to make an effective separation you must first achieve liberation. Therefore, the laboratory and plant studies examined the liberation characteristics within the lead circuit, and the impact of regrinding. The work demonstrated clearly that galena/sphalerite liberation was poor, and significantly impaired plant performance. Further, it was suggested that the application of lead regrinding of the lead scavenger concentrate and the lead first cleaner tailing would not only benefit lead metallurgy, but also improve sphalerite flotation. A similar approach was then applied to the zinc circuit. From these studies, solutions applying simple circuit changes utilising existing equipment were proposed and implemented. Further to the improvements in galena/sphalerite liberation, significant improvements in concentrate quality were achieved by reducing variation within the process. The implementation of changes in work practices negotiated in the Enterprise Agreement, employee contributions and specialist training also made a significant contribution to the unprecedented improvement in the lead and zinc flotation circuit performance. The results of these plant changes are discussed, along with the suggested scope for further improvement.

Jan 1, 2000

Evidence abounds for sea-level change having occurred throughout geological and recent time. Driven by climatic changes, by cycles of glaciation and deglaciations, and by tectonics the position of sea-level relative to the crust has been going up and down since oceans first formed. Rates of these differential movements have been as high as 10 mm/year during the last major deglaciation as sea-level rose by about 150 m in about 15000 years. Tectonic processes can also produce change in sea-level relative to the crust of several mm/year as in, for example, the uplift of the Huon Peninsula in Papua New Guinea. To understand what is happening to sea-level today and what may be happening in the future it is necessary to understand the geological and climatic processes that have caused sea-level to change in the past and the best laboratory for the study of these processes is the geological and geomorphological record. Evidence for observations of sea-level change throughout Late Pleistocene and Holocene time is plentiful in the Australian region. Temporal variability is characterized by a low-stand, at more than 100 m below the present level, at about 20 000-18 000 years ago followed by a rapid rise and transgression of the continental margin up to about 6000 years ago. After this time sea-levels remained within a few metres of their present value but the patterns of change are not everywhere the same. The depth of the low stand at about 18 000 years ago does not appear to have been the same everywhere. Nor does the time at which sea-level first reached its present value appear to have been everywhere the same. The fluctuations about present sea-level during the past 6000 years appear to have been different in different localities. As yet there has not been a wholly satisfactory quantitative explanation for this spatial variability. How much, if any, is indicative of vertical tectonics? How much is the result of the Earth's response to the changing surface loads as mass is exchanged between ice sheets and the oceans? Can any of it be attributed to past changes in global climate? Or are the observations just wrong?

Jan 1, 1990

Reliable sampling practices are the key to optimising the market value of a mining or chemical companyÆs stock. As a result, reliable sampling standards are needed. However, current standards on sampling present the æuniversalÆ Pierre GyÆs Sampling Theory in an ambiguous way. For example, the Total Sampling Error is divided into its basic components only in informative annexes, when it should clearly be the main body of the standard. Sampling standards are presently loaded with statistical concepts that actually belong in the annexes. Furthermore, many non-probabilistic sampling procedures are still mentioned which do not belong in a standard. The objective is not to criticise existing sampling standards, but to suggest better ones. Sections on the Sampling Theory should divide the Total Sampling Error into a sum of its nine basic components. Then, and only then, should they be addressed one at the time. Sections for establishing a sampling protocol should address the in situ Nugget Effect, the Fundamental Error, the Grouping and Segregation Error, the Long Range Quality Fluctuation Error, and the Periodic Quality Fluctuation Error. Sections for sampling methods, mechanical sampling, manual sampling, grab sampling, sampling of trucks, railroad cars, bags, and drums should be part of the critically important practical implementation of a recommended sampling protocol, called Sampling Correctness. It includes the increment Delimitation Error, the increment Extraction Error, the Weighting Error, and the Preparation Errors. Unless these errors are addressed one at a time, in an unambiguous way, the standard will remain ineffective in solving sampling problems for the industry. Therefore, a strategy is needed to create better standards required at the early stages of new projects, both by manufacturers of sampling equipment and by engineering firms. A logical sequence of important points that cannot be ignored in any sampling standard is presented. An analysis of the practical use of the words sampling uncertainty versus sampling error is recalled. Finally, as a practical example, an in-depth analysis of the correctness of cross-belt samplers is presented, and emphasis is placed on the correct ways to perform bias-tests for mechanical sampling systems.

Jan 1, 2005

This paper examines some of the important aspects of mineral taxation policies and practices, with reference to the mining tax regimes of selected Pacific Rim countries (see Tables 1 and 2). The following subjects are addressed:what is æmineral taxationÆ?, basis for mineral taxation, types of mineral taxes, objectives of the mineral taxation regime, best practices, and mineral royalties. Many countries, in some cases with the encouragement and assistance of international funding agencies, are actively assessing the international competitiveness of their mining tax regimes with a view to attracting investment. However, these countries recognise that the mining tax regime is not the only consideration that is taken into account by prospective investors. The countryÆs geological prospectivity, physical infrastructure, labour force, political risk, and regulatory system are also important factors in the investment decision making process. Although it is probably true that an attractive mining tax regime will not necessarily attract mineral investment, there is a real possibility that an unattractive regime can drive away investment. For example, Hugo Dummett, general manager for discovery at BHP, hinted recently that BHP could cease exploration in Russia in the absence of positive tax changes. Dummett is reported as saying that if taxes æend up being as onerous as they are now, we really have to rethink why we are hereÆ (Mining Journal, London, November 27, 1998).

Jan 1, 1999

By R B. Wanty

Historically, most investigations of biogeochemical cycling in acid rock drainage systems involved synoptic sampling over longer time periods (one sample per week or month) or intensive time series studies over a few hours or days. However, many important episodic loading events, such as seasonal meltwater and storm events occur on timescales that are rarely observed by these traditional sampling approaches. Monitoring these transient processes, which may contribute the bulk of the annual metal loading, is essential for accurate assessment in acid rock drainage areas. Recent work also has demonstrated dramatic diel (24 hour cycle) variations in trace metal concentrations in response to diel changes in temperature, pH, oxygen, and photochemical cycling (Brick and Moore, 1996; Nimick et al, in prep). To characterise a system that may respond to diel, seasonal, and episodic events, a monitoring program must sample at a frequency that captures the details of these major forcing events. We developed two novel instruments, the Zn-DigiScan and the DigiSampler to examine low and high frequency temporal changes in acid rock drainage areas. The Zn-DigiScan is a battery powered real time in situ chemical analyser designed for long-term deployments with hourly analyses of Zn. Stream physical parameters (temperature, conductivity, dissolved oxygen, pH, turbidity, etc) were measured every 15 minutes with a water quality sonde. The DigiSampler was developed for the long-term daily sampling of biogeochemically active elements and can take either discrete samples or samples integrated over 24 hours. The DigiSampler collects 2 ml samples in a Teflon coil which are separated by 0.2 ml nitrogen bubbles. The sample coil is returned to lab and the 2 ml samples are diluted 1:10 and analysed for trace metals by ICP-MS. Initial results from a three-day deployment at Fisher Creek, MT, USA have successfully demonstrated the ability of the Zn-DigiScan to record Zn concentrations at levels below 100 ¦g/L. Zinc concentrations measured at 30 minute intervals in Fisher Creek showed a diel cycle with low values of ~25 ¦g/L in the late afternoon and increasing to ~60 ¦g/L by early morning. Zn concentrations were inversely related to temperature and pH, suggesting that temperature and pH dependent adsorption was the main factor controlling diel Zn fluctuations. Initial deployment of the DigiSampler also was successful, revealing diel cycles in Zn, Cu, and Mn. Comparison of trace metal samples collected by the DigiSampler showed good agreement with samples collected by an Isco automated water sampler, demonstrating that the DigiSampler can collect clean samples for trace metal analysis at the low ¦g/L range.

Jan 1, 2003

Stringent environmental benchmarks imposed by governments and successful legal challenges in the country of origin have changed the risk profile for all mining companies over recent years. In developing countries, however, where high government standards may not always be in place, direct community action has often made worthless substantial investments in otherwise viable mining operations. Real limitations are therefore imposed from these risks on all areas of mining activity, wherever they may be. Thus, the bar has been raised for all companies developing or operating mines. This paper argues real financial and global industry reputation benefits accrue when all known environmental risks, where practical, are managed. In response, among major international mining companies, as the industry moves towards greater global consolidation, senior management teams have increasingly adopted corporate governance standards including æTriple Bottom LineÆ (shareholder/government/community) sustainability reporting. Sustainability reporting is encouraged by improved international stockholder and financial investor perceptions by contributing to lowered social, community and geopolitical risk which lowers the cost of access to funds as well as improving staff morale and productivity. New mines must not only be primarily financially viable but must operate throughout in a sustainable way. Case studies of some recent mining operations, who have not foreseen or proactively managed major environmental risks, demonstrate the dire financial and personal implications for managers, directors and shareholders from not identifying and managing these environmental risks. Merely having a corporate policy statement on environmental standards or high level Government approvals process for a mining activity does not preclude mining operations from the risk of direct action by local populations or future adverse legal implications from risks which were perhaps identified but not mitigated effectively. Methods and processes for the identification and active management of environmental risks in the global arena are discussed to add a practical element to sustainability, based on the authors recent strategy development processes with governments and major mining houses such as BHPBillition, Rio and Xstrata. Emphasis is placed on proactive, innovative yet practical solutions which, where possible, show positive contributions firstly to the financial bottom line but also the community at large.

Jan 1, 2003

This paper outlines the role of commissioning in the project cycle, shows how to get organised for commissioning and describes the principal commissioning activities. Emphasis is placed on appointing key commissioning staff early in the project to coordinate the preparations for commissioning and on detailed planning and tracking to ensure that the required commissioning activities are performed satisfactorily. The management of safety during commissioning is reviewed.

Jan 1, 2005

By A E Reschke

The high-shear colloidal mixer is generally recognised as the most efficient method of mixing cement based grouts. Only recently however has this technology been applied to the production of cemented rockfill (CRF) for use in underground mines in North America. Traditionally, paddle type mixers have been used to produce the cement based slurries required for the preparation of CRF. While considerable success has been achieved with these mixers, tremendous advantages are attained with the colloidal mixer. The combined effect of the highly efficient mixing action and the ability to mix low water/solids ratios, allows for reductions in the cement content for a given strength requirement. Cement can also be replaced by cheaper fillers such as flyash, resulting in further cost savings. Although large-scale dedicated CRF hatching plants are typical, there is a growing need for mobile plants capable of operating anywhere underground. The compact size and rapid hatching speed of high-shear colloidal mixers has allowed them to be incorporated into skid mounted systems capable of producing and discharging cement based slurries onto rockfill aggregate for the production of CRF. In many cases run-of-mine development waste can be used as CRF aggregate with these slurry plants thereby reducing the cost of waste rock removal. These relatively low cost portable plants have now allowed several mines to economically rccmer isolated pillars and realise positive returns on their investment.

Jan 1, 1998

By Szwedzicki T

In recent years substantial advances have been made in the field of geomechanics. Staff at the Western Australian School of Mines (WASM) are keen to see that such advances continue and that the mining industry in Australia can take full advantage of such developments in a timely manner. WASM views mining geomechanics in its broadest sense, as being concerned with the characterisation of the physical properties and the behaviour of earth materials (soil, rock and water) and openings as mining proceeds. Aspects such as, soil and rock improvement techniques for difficult site conditions and the rock breaking processes, are also considered to be an integral part of mining geomechanics. This paper indicates the inter-relationships between the various areas within the field of geomechanics and the strong reliance of all of these areas on site specific engineering geology.

Jan 1, 1992

I would like to start by thanking The AusIMM and CSIRO for organising this excellent conference and inviting me to give a keynote address. Today I will focus on some broad observations of our industry, and leave the technical discussion to my colleagues who are presenting specific papers covering a wide range of topics. In preparation for this paper, I did a little research into the early history of the Pilbara iron ore industry. I was fascinated to read a quote attributed to Harry P Woodward, the Government Geologist in the late 19th century, before Federation. Mr Woodward described the Pilbara as an iron ore country and observed that æthere is enough to supply the whole world should the present sources be worked outÆ. Mr WoodwardÆs prediction could be viewed as wishful thinking and certainly at Hamersley Iron I would gladly envisage the Pilbara supplying the worldÆs entire iron ore needs! In reality, Western Australia accounted for 162 million tonnes or 36 per cent of seaborne trade in 2001. An impressive effort, but not quite the total world supply as Mr Woodward imagined. But we shouldnÆt dismiss these historical musings out of hand û perhaps we could see it as a challenge for the industry to æwork outÆ the present sources. We all know there is abundant iron ore in the Pilbara, and I expect it is only a matter of time until our collective technical expertise and sheer hard work will enable us to utilise its greater range of ore types. Opening up new markets will be a key pathway to creating additional value from the Pilbara ores. Today I will examine the state of play of our industry and the major influences that shape our business at present, before considering what the future might hold for us. I canÆt guarantee the accuracy of my crystal ball, but the stability and long-term nature of our industry does enable some reasonable hypotheses on where we are heading. I will also spend some time examining the way in which the iron ore producers are working to maximise the value of their resource base and obtain more from their existing capital assets.

Jan 1, 2002

By A E. Waltho, W J. Shaw

Predicting the physical characteristics of various ore types has for long been a difficult problem during mining. Grade control practices tend to concentrate on the chemical grade of the ore. Estimation of physical characteristics such as beneficiation behaviour is commonly limited to the simplistic application of historical averages. Large amounts of geochemical data are often gathered during the exploration and mining stages of a project, especially in ferrous and base metal deposits. In addition to the elements of principal economic interest, samples are often analysed for suites of gangue constituents to determine whether the mineralisation lies within target specifications. This multi-element data is often put to no other use than this simple chemical classification, yet it may present the geologist or metallurgist with valuable insights into the mineral content and physical characteristics of the deposit. Normative mineral estimates have been used as a method for characterising igneous rocks for almost 100 years. The method establishes and applies a set of sequential rules, by which the chemical components of a sample are assigned to mineral components. Provided that it is possible to make some realistic assumptions about the mineral species likely to be present in a rock unit or deposit and their paragenesis, this approach can be extended to a variety of mineral deposits. The geochemical data that are routinely collected when, for example, drilling iron ore and base metal deposits, can be used to derive estimates of normative mineral content. These estimates can be used to characterise physical or metallurgical aspects of the ore, such as density, beneficiation behaviour and metal recovery. This paper examines the application of normative mineral estimates to a variety of practical resource characterisation problems. The potential for predicting the lump and fines proportions of iron and manganese ores is also discussed.

Jan 1, 1999

The underground storage of LPG and other hydrocarbons is in current commercial use in Northern Hemisphere countries in Europe, Asia and the USA.Elgas Pty Ltd, a 50 per cent joint venture between AGL and BOC, embarked on a worldwide feasibility investigation in 1989 to establish the viability of constructing an underground LPG storage facility in Sydney, Australia, the first of its kind in the country. Elgas recognised that with the limited 19 000 tonnes of storage capacity at Port Botany and the limitations imposed by use of small coastal ships (up to 10 000 tonnes capacity), a larger storage facility was required to utilise higher capacity ships from more remote sources such as the North West shelf and overseas. This would achieve security of supply in high demand periods and economies of scale. The underground option also provides improvements to safety and environmental standards.

Jan 1, 1999

Over years of exploration the massive and tabular orebodies in the area to the South West of Western Areas Gold Mine had been assessed as containing about 50 million ounces of gold û a world class orebody. Planning initially was for a surface and subvertical shaft system to exploit this area but because of cost, a single lift shaft to an area which could be accessed ex Western Areas was planned to intersect the reef at 2760 metres. It was also planned to mine out the shaft pillar area long before the deep shafts would reach that position. This is not the normal practice in South African Gold Mines. The stoped out shaft pillar was backfilled to minimise movement in the shaft sites. The result of a competitive tender/adjudication process was that Cementation Mining û Skanska won and was awarded the R192 million contract to sink the Main and Ventilation Shafts on 15 June 1995. On 1 April 1999 Western Areas and Placer Dome SA formed a Joint Venture, which now owns and operates the mine on which the South Deep Shafts are situated. This situation prevails today.

Jan 1, 2002

By G V. R Goodman, G J. Chekan, J M. Listak

The extraction and transport of coal from underground coal mines can result in significant liberation of coal and/or silica dust into the mine atmosphere. Mine operators have long used ventilating air as a primary means of diluting generated dust, removing dust from the working faces and preventing dust from reaching the minersÆ working environment. As production levels have increased, mine operators continue to be challenged in maintaining dust concentrations below compliance levels. The need for maximising the effectiveness of available ventilating air in conjunction with other effective controls, such as water sprays and dust collectors, continues to be critical to the long-term health of mine workers. The National Institute for Occupational Safety and Health (NIOSH) has conducted full-scale laboratory and mine-site research to evaluate improved application of dust controls for both longwall and continuous mining methods. A summary of recent research results and recommended practices will be provided.

Jan 1, 2005

By S Nie, I Bergqvist, F Ouchterlony

In blasting, a few or many cracks are driven from the borehole into the rock. But what causes the cracks? The most common theory of breakage consists of two stages; first the shock wave causes radial cracks to form around the hole then the gases penetrate into the cracks, and widen them and make them longer. Another theory presented by Brinkmann suggests that the back damage is primarily controlled by shock and that the gas penetration is the mechanism controlling breakout of the burden. He did his experimental work using blasthole liners. Recent research at SveBeFo has examined this matter further. In a quarry a number of benching holes have been blasted simultaneously. In some of these holes tubular Swellex bolts were inflated and decoupled charges put inside the tubes without stemming. Other holes were identically charged but without the lining. Finally some holes were also stemmed. After blasting the cracks in the remaining rock were studied. There was no difference in crack lengths between holes charged normally (no stemming) and holes where the charges were inside the bolts. On the other hand when stemming was used, the crack lengths increased for some explosives but remained the same for an emulsion explosive. In another set up blasted granite blocks were charged in the same way as above. Then we could also measure the bore hole pressure. The pressure gauge consists of a small carbon resistor inside a steel cylinder. It is called LHM (Location-fixed Hydrodynamic Measuring Cup) and is placed at the bottom of the hole. A smaller exit hole from the bottom is drilled for the cables. The paper presents the technique and the results obtained from both the quarry blasting and the blasting of the blocks.

Jan 1, 2001

By Iley J. D, Siviour N. g, Moffatt R. J

The process of desilverising by fractional crystallisation with reflux was investigated through laboratory batch tests and continuous laboratory bench scale tests at CSIRO Clayton, to a 300 kg/hr pilot plant at Port Pine. The pilot plant built at BHAS comprised a vertical cylindrical refining column with internal diameter 250 mm and height 3.2 m, attached at the top to an off-set cylindrical stirred crystalliser tank. Crystals were made in the crystalliser by intermittent immersion of steel cold fingers, which were water cooled between immersions. Gas heat was used for melting the crystals at the base of the column and for side compensation heating. A computerised in strumentation system was employed for data logging and for controlling some critical plant operations. A mechanical device was first employed to promote counter-current plug flow of crystals down the column against the rising stream of reflux liquid, but this was found to be unsatisfactory owing to excess noise, frequent mechanical failure, and excessive accumulation of dross. Plug flow was finally promoted by pulsing the column. Low silver levels, less than 1 gitonne, were achieved with both methods of crystal transport under total reflux conditions. The pulsed column gave results for silver and bismuth which agreed with the theoretical predictions of a computer model, but there was some selective drossing of antimony. In the mechanically agitated column, excessive drossing promoted selective removal of most of the antimony and some of the bismuth, and the results after extended operation were well removed from the theoretical predictions. Plant failures and operating problems prevented the achievement of satisfactory product quality with the necessary reliability under production conditions. Other priorities necessitated the termination of the project before the process could be optimised.

Jan 1, 1989

By Sneddon A

Expansion of central production facilities at the Kutubu Petroleum Development Project in Papua New Guinea (PNG) required excavation of a steep hillside overlooking operating crude oil processing, storage and pumping facilities. Drilling and blasting were used to remove a large volume of rock which varied from hard limestone to soft sandstone, with zones of soft clay and many underground caverns. Similar ground conditions had made it very difficult to predict and control blast-ing results during previous excavation in this area.Special conditions of the project included restrictions on ground vibration levels at a high pressure oil pipeline and pump station within 100m of the blasting area, and a prohibition on any flyrock. As work progressed, some blasting was necessary with 20m of installations being constructed on the levelled project site. Thus blast design, drilling and charging were carefully controlled to avoid any incidents which could interfere with oil production or progress of the construction project.

Jan 1, 1994

By H Kundapen, J J, C Rumble, S Miller

This paper describes measures taken by Ok Tedi Mining Limited (OTML) to minimise the risk of acid rock drainage (ARD) resulting from mining operations at its Mt Fubilan porphyry copper-gold mine in the remote Star Mountains of Papua New Guinea. The risk of acid generation and metal leaching as a result of oxidation of these sulfidic deposits has long been recognised by OTML. In 1998, OTML instigated the ARD Management Program to fully evaluate these risks and to formulate, if necessary, trial and implement appropriate management strategies. In implementing the ARD Management Program, OTML has adopted a risk management approach consisting of five stages: risk identification, risk analysis, risk assessment, risk treatment, and review and monitor. Significant progress has been made in relation to risk identification, analysis and assessment. The work currently underway to put in place a comprehensive risk treatment and review process will ultimately determine the success or otherwise of this approach.

Jan 1, 2003