Search Documents

By S. Banisi, E. Arghavani, A. Akbari, Gh. A. Parsapour, S. Darvish Tafvizi

The new copper processing plant of the Sarcheshmeh copper complex consists of two parallel circuits. After a primary crushing, the ore is sent to a SAG mill and the product is further ground in a ball mill. The overflow of the hydrocyclones is fed to a flotation circuit which contains 8 rougher tank cells (RCS130), 3 cleaner cells (RCS50), 5 scavenger cells (RCS50) and a 4 x 12 m flotation column as recleaner. The circuit was initially designed to process a feed containing 0.8% Cu, but because of the ore type change, the feed grade decreased to 0.6% Cu. This resulted in a reduction of final concentrate grade and recovery from 28 and 85.5% to 24 and 84.4%, respectively. Based on the original design, the copper and silica recovery in the cleaner cells should be 69 and 55%, respectively, but these values increased to 85 and 75% because of a higher retention time. The rather high silica recovery (i.e., 75%) was found to be the main source of the lower final concentrate grade. In order to reduce the retention time of particles in the cleaner cell from 13.7 to 6.9 min, the rougher concentrates of two parallel circuits were fed to only one cleaner-scavenger and regrind circuit. This modification increased the cleaner and final concentrate grade from 15.1 and 24.5% to 17 and 26%, respectively. To prevent a possible reduction in the copper recovery, the froth depth in the scavenger cells was reduced. The overall outcome of the circuit modification was evaluated to be a 10% reduction in the energy consumption without any loss in the overall copper recovery.

Jan 1, 2016

By P. N. Calder, D. B. Apel, S. D. Butt

Mine-wide (MW) microseismic systems use widely spaced transducers to determine the source location and parameters of stronger microseismic events, while high frequency (HF) systems use fewer transducers to monitor local areas for the weaker events that can precede stronger events. Previous monitoring at the Creighton Mine indicated that an HF transducer located 120 m away from an active stope recorded two types of activity in response to production blasting: the first occurring at the same time as the production blasts and associated with the passage of the direct seismic waves from the blast through the local area, and the second occurring several hours later and associated with the arrival of a slower moving stress change through the rock mass (which was identified by the mine’s MW system). Interpretations of locally increased stress levels, based on analysis of the recorded HF events, correlated with the nearby occurrence of two strong seismic events. These results were applied to a similar monitoring trail at the Kidd Creek Mine where the transient stress changes induced by several development blasts were monitored. It was observed that increases in HF activity corresponded with the occurrence of MW events near the transducer location, and that fewer HF events were recorded the longer this occurred after the blast. Local geological features appeared to influence the number and occurrence of both HF and MW events.

Jan 1, 2000

By D. C. Rance

"The Quintette Coal Limited property is located in the north east coal area of British Columbia. A basic agreement with the Japanese steel industry was ex ecuted on January 27, 1981 for the sale of 69.5 million tonnes of Quintette metallurgical coal over a 14.5-year period. This contract period can be extended by Jive years by mutual agree ment. Sale agreements have also been signed for the sale of 19.4 million tonnes of oxidized coal over a 15-year period. Work started on site development in the late summer of 1981, and at present, two of the four eventual pits-the McConkey and Frame-are under development. The pits are currently in a pres/ripping phase. These pits are notable for the stripping volumes that have to be removed from relatively small pit areas. in order to provide for the required detailed rapid short-range planning of these pits, engineering will be computerized, as will the truck dispatch system. The mining area lies 21.1 km from the plant site by road and the transport of raw coal LO the plant is by means of a highspeed conveyor system which has a total length of 13.4 km with a vertical drop of 740 m. The surface plant facility was designed on a modularized basis to facilitate maintenance, and is designed to enable the use ofgravity flow ofraw coal and heavy media in the plant to minimize the use of pumps. The construction of the plant and mine site facilities is on-going, and the first coal production is scheduled for early December 1983. Introduction Quintette Coal Limited is a Canadian company incorporated in the province of British Columbia in 1971. Denison Mines Limited is the manager of Quintette's activities. Equity in Quintette Coal Limited is held by several shareholders, with interests as follows: Denison Mines 'Limited, 500Jo; Charbonnages de France International S.A., 120Jo; and Japanese interest, 38%. The project will develop almost 120 million tonnes of coal for marketing during its first 20 years of production. All of the planned production tonnage has been committed to Japanese markets. Most of the coal will be metallurgical grade, and the remainder will be a high-quality thermal coal. The Mcconkey and Frame pits, which will initially provide the mine's production, will commence production in early December 1983 and will, in 1985, reach the full annual production of 5 million tonnes clean metallurgical coal and 1,380,000 tonnes of clean thermal coal."

Jan 1, 1985

By A. Iizuka

This study was aimed at separating and recovering arsenic, antimony, and tin from refining byproducts generated in a nonferrous smelter. The target byproduct was a silicate slag containing the above elements. The silicate structure of the slag was destroyed by alkali roasting, which then enabled leaching of arsenic, antimony and tin in solution effectively. Arsenic was selectively leached out by hot water after alkali roasting of the slag, while remained antimony and tin in the residue were leached out by a hot hydrochloric acid solution. However, when the solid-liquid ratio in the leaching solution was increased, hydrous gelatinous silica (gel-like silica) was formed during the hydrochloric acid treatment and filtration became difficult. Therefore, high temperature and high pressure leaching was attempted to improve the filterability of the silica leaching residue. In the high temperature and high pressure treatment, the hydrous gel-like silica was transformed into easily filterable aggregated silica, and thus, filtration became easy. By investigating the neutralization and sulfurization treatment for the obtained hydrochloric acid leachate (second leachate), it was possible to separate antimony and tin. INTRODUCTION This study aims to separate arsenic and recover valuable metals such as antimony and tin from refining byproducts generated in a nonferrous smelter. The target smelting byproduct is antimony-containing slag in this study. In many cases, alkali roasting was adopted as pretreatment for extraction and recovering valuable metals from smelting residues and wastes (Rao, 2006). For antimony-containing slag in this study, one effective method for separating arsenic is to convert arsenic to sodium arsenate (Na3AsO4) by roasting with a sodium compound and then to remove arsenic by hot water leaching. In addition, by alkali roasting, the silicate structure of the slag is destroyed, and effectively alkalizing tin and antimony is accomplished. Then, precipitating and recovering tin and antimony leached into the acid solution are considered possible by sulfurization and neutralization treatments. In this research, we conducted basic studies on the following. 1) Destruction of silicate structure in slag by alkali roasting and leachability of arsenic. 2) Conversion of hydrous gelatinous silica to aggregated silica by hydrochloric acid treatment of residues after arsenic leaching under high temperature and high pressure, as well as leachability of antimony and tin. 3) Separation and recovery of antimony and tin by sulfurization and neutralization treatments of hydrochloric acid leachate. These topics of investigation can support to consider the separation and recovery process of arsenic, antimony, and tin from antimony containing slag.

Jan 1, 2019

By Jürgen Kretschmann

The Islamic Republic of Iran is a very important producer of raw materials in the world. The country holds 68 types of minerals, including salt, sand and gravel, chrome, lead, zinc, copper, coal, gold, and iron-ore. With more than 37 billion tons of measured and indicated reserves and 55 billion tons of total mineral resources, Iran is ranked among the 15 major mineral-rich countries. Sangan iron-ore mines (SIOM) is one of the biggest iron ore mining complexes in Iran, located in a remote, but strategically important area near the Afghanistan border. The Iranian government has planned several mining projects in this region for a stepwise development over the next 5 years to satisfy the growing demand of the Iranian steel industry. In cooperation with private companies, these projects shall be realized as sustainable as possible. This paper introduces SIOM and describes socially responsible activities undertaken during the initial development of this mining complex. The effects of these activities will be demonstrated. Unique attributes of the Sangan area have a significant impact on the acceptance of SIOM by regional stakeholders. The government has made several social investments that benefit workers´ families and the community. They are attempts to build social capital for the mining operations and demonstrate a commitment for socially responsible mining to the communities and the local population. They aim to create a balance between the local and regional expectations and requirements and the necessity to secure the corporate profitability at a reasonable and sustainable level. Investment in socially responsible activities is not a choice but a necessity to improve the relations between mining companies and stakeholders in the communities. It is recommended that social investments should be carefully planned and implemented from the early stages of mining activities, and should proceed throughout the life cycle of the mines.

Aug 1, 2013

By K. Yamaguchi

To contribute highly efficient and environmentally conscious copper smelting process, several topics in chemistry of the continuous converting were discussed. Through the reviewing the authors' thermodynamic simulations, it is recognized that small amount and low copper content of the coexisting slag is preferable. Some discussions were added to the Takeda's diagram for Cu20-FeOx-CaO ferrite slag, and the activity curves of the constituents were derived. Thermodynamic calculations were carried out on the copper contents of the slag during the blister copper formation. The dissolution of copper in slag decrease somewhat with increasing temperature, but the effects of increasing S02 pressure and decreasing %S in copper are considerable to increase in copper content of the slag. The optimum oxygen enrichment in the supplied air, and regulation of the oxidation degree for the blister copper are important in practice. The gypsum phase separation in the calcium ferrite slag was also evaluated thermodynamically, and concluded that decreasing temperature, increasing CaO content or S02 pressure, and extensive oxidation of the blister copper tend to separate CaS04.

Jan 1, 2007

By Z. Bibak, S. Banisi, A. Ghasemi, E. Nematollahi

"The use of large AG/SAG mills in the mineral industry has been on the rise recently due to a significant reduction in the capital and operating costs for achieving significant increases in plant throughputs. The major reason for downtimes in these mills is the time taken for the replacement of broken or worn liners. This loss of “availability” of these units has a significant impact on the productivity of these plant operations. The ability to predict liner life time and its evolving shape could help to optimize these comminution operations. In the past decades, various models have been proposed to estimate liner wear rate, but because of their empirical nature they could only be used within certain limited operating conditions. In this research, a phenomenological model which could predict the liner wear rate was proposed and tested. This model considers parameters such as; operating conditions, liner hardness, pressure on the lifter, and, relative velocity of particles and mill shell. Data from industrially measured liner profiles were taken during the liner life time at the Sarcheshmeh and the Gol-E-Ghohar SAG mills to provide a solid base to calibrate and validate the model. The comparison of the model predictions with the actual measurements of the liner wear rate showed that the results were in a good agreement at both, the Sarcheshmeh (R2=0.94), and the Gol-E-Ghohar (R2=0.97) concentrators.INTRODUCTIONAG/SAG mills are one of the most important technologies in the mineral processing industry in the recent decades. The “Availability” of these units in a plant operation is one of the most important economic parameter for evaluating their performance. The major reason for the downtime of these mills affecting their “availability”, is the time required to change worn or broken liners (Yahyaei, Banisi, & Hadizadeh, 2009; Maleki-Moghaddam, Yahyaei, & Banisi, 2012). The knowledge about the magnitude and profile of liner wear not only enables more accurate liner life estimation to prevent unwanted interruptions of the SAG milling in mineral processing plants and more strategically plan the scheduled mill outages for liner changes. It also could provide key information needed to select an appropriate liner design (Yahyaei et al., 2009; Rezaeizadeh, Fooladi, Powell, & Weerasekara, 2010a)."

Jan 1, 2016

By I. Filzwieser, M. B. Hanel, A. Filzwieser

The paper describes the current density increase within the last 150 years. From the beginning in 1885 at 30 A/m² up to the highest used current densities nowadays at 420 A/m² towards future pathways were even 1000 A/m² can be achievable. A short tour through history will highlight the milestones of the process of electrolytic refining of copper. Besides the improvement of the existing technology, the biggest changes leading to higher possible current densities are linked to the introduction of the ISA stainless steel plates and the introduction of the parallel flow principle. Furthermore, the parameters influencing the limitations regarding current density and therefore the practical used current density as well as the influence from the chemical composition of the electrolyte is discussed. Finally, the possibility of further increasing the current densities by enhancing the relative movement between electrolyte and electrode will give an outlook about the future of the copper electrolysis process. INTRODUCTION The current density is the most important characteristic to describe the productivity of a copper refining electrolysis besides the characteristic number for the electrical efficiency. Over the last 150 years, current density has risen from a few amperes per square meter to over 400 A/m² without any significant change in the principle of electrolytic refining. This increase in current density is documented exemplary by the electrolysis of Montanwerke Brixlegg in Austria (Brixlegg, 1963, 2013). The very beginning of the technology of electrolytic refining of copper was first patented in England by James Elkington in 1865 and the first electrolytic copper refinery was built in Newark, New Jersey, in 1883 (Armstrong, 1999). The secondary smelter Montanwerke Brixlegg, Austria, has been operating an electrolysis plant since 1884. In 1988, the third "Mount Isa" electrolysis plant worldwide and the first in Europe was put into operation in Brixlegg. Since 2010, the so-called high-current electrolysis (parallel flow METTOP-BRX Technology) with a current density of approx. 400 A/m² has been operated in half of the electrolysis process.

Jan 1, 2019

By J. R. Emery, D. F. Coates

"FOUR PAPERS ON CEMENTED BACKFILL were given at the Annual General Meeting of The Canadian Institute of Mining and Metallurgy in 1970:Weaver, W. S., and Luka, R., ""Laboratory Studies of Cement-Stabilized Mine Tailings"".Pasieka, A. R., Beattie, H. F., and Espley, G. H., ""Cemented Hydraulic Backill within the Falconbridge Group of Companies"".McLeod, P. C., and Schwartz, A., ""Consolidated Fill at Noranda Mines Limited (Geco Division)"".Clement, W. P., and Sokoloski, R., ""Pumping Cemented Backfill"".These four papers give the impression of a development in mining technology that has been substantially completed. Somewhat over ten years ago, The Inter-national Nickel Company of Canada, Limited and Falconbridge Nickel Mines Limited started experimenting with the addition of Portland cement to mill tailings to produce improved backfill and cheaper floors for scraping. Shortly after, the Canada Cement Company Limited (now Canada Cement Lafarge Ltd.), with full support of the two mining companies, started an extensive research program to provide the technologic-al data necessary to exploit what was obviously going to be a significant development in mining technology."

Jan 1, 1970

By A. Taylor, E. Thorn Corthay, J. Farrell, L. A. Westfall, S. Borchardt

Mining and metallurgical industries need to minimize their greenhouse gas (GHG) emissions; Hatch specializes in conducting mining and metallurgical energy management assessments and optimizing productivity. Projects executed have demonstrated that there is a wealth of energy management, waste reduction, and process efficiency improvements that require no or low capital investment. Typical energy cost savings are on the order of 5% to 12%, with similar reductions in GHG emissions. Hatch generates Marginal Abatement Cost Curves to optimize the implementation pathway, maximizing carbon abatement and minimizing cost. The findings of a practical case study from Cameco are presented.

Jan 1, 2010

RISKGATE is an interactive online risk management system developed by the Minerals Industry Safety and Health Centre (MISHC; University of Queensland) to assist the mining industry in implementing continual improvement in management of major unwanted events so maximising health and safety performance. A comprehensive body of knowledge has been compiled from diverse mining industry experts for risk management of tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives, manual tasks and slips/trips/falls. This paper presents an overview of the RISKGATE body of knowledge captured specifically for the management of unwanted events that stem from the handling and use of explosives (drill and blast) within surface coal mining operations. The knowledge presented is divided into a series of initiating events (listed below) within which there are further degrees of classification based on design, operation, and management concerns. Initiating events: ? Loss of control of explosives and associated chemicals in storage on site ? Loss of control of explosives and associated chemicals during transport ? Loss of control of explosives and associated chemicals during manufacture ? Loss of control of explosives and associated chemicals during handling and blast operations ? Loss of control of explosives and associated chemicals during disposal The system guides the user in generating substantive and leading-edge controls to assist in the design, management and reporting of drill and blast operations to meet stringent internal and external requirements. From a broader industry perspective, RISKGATE provides an environment for knowledge capture and knowledge exchange to drive innovation and best practice in the identification, assessment and management of risk. By capturing operational knowledge from industry experts, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover in the coal industry.

Aug 1, 2013

By F. Baczek, S. S. Rocks, D. Chaiko, C. Eyzaguirre, S. Asihene, T. Walters

The majority of efforts to improve primary copper sulfide leaching have focused on solution chemistry, temperature, O2 pressure, ultra-fine grinding, the use of catalysts, etc. Historically, very few studies have focused on the solid/solution interface. A new, patent pending approach to catalyzed, copper sulfide leaching has been discovered by FLSmidth that enables manipulation of the 2-D semi-conductor properties of chalcopyrite surfaces to the benefit of higher electrochemical reactivity. Copper dissolution rates are then further accelerated by incorporating a Stirred Media Reactor (SMRt) into the process. By using minute amounts of Cu2+ to "pre-activate" chalcopyrite, leach times have been reduced from >20 hours with incomplete Cu dissolution to <2 hours with 98+% Cu dissolution at 80°C. The pre-activation process takes only minutes to complete at temperatures of 80°C or less. The total atmospheric leaching process, incorporating the pre-activation and Stirred Media Reactor is compatible with existing SX/EW processes. Results of batch leach testing are presented and possible mechanisms are discussed.

Jan 1, 2015

By D. W. Duncan, A. Bruynesteyn

Acidic mine waters containing solubilized uranium have been observed in many uranium and some copper mines. In every case, the sulphide and iron oxidizing bacterium, Thiobacillus ferrooxidans, was also present. This bacterium provides the ferric iron required to oxidize u+4, both by oxidizing available ferrous iron and by oxidizing pyrite or other available sulphide minerals. This latter oxidation also provides sulphuric acid and may increase extraction by exposing more uranium. The enhancement of bacterial activity and the results of some field tests are discussed.

Jan 1, 1971

By A. R. Pasieka, J. C. Wilson

"Compressed air still remains an essential source of power in underground hardrock mining. As a power medium it has a high convenience factor, although, in many cases, it is expensive to generate and maintain. Until new methods of breaking rock and/ or satisfactory alternatives to air-driven rock drills are developed, compressed air is indispensable. It is essential to utilize this source of power to a maximum by keeping all pneumatic tools supplied with air in adequate quantity and at optimum pressure.In search of the optimum operating air pressure, con-trolled drilling tests were undertaken at dynamic pressures ranging from 90 to 140 psi.Test results show the effect of increasing air pressure on: the performance of various jackleg drills at varying pressures, the life cost of drill steels and TC bits, and drilling efficiency at varying pressures. From the fore-going, a criterion is proposed for selecting efficient rock drills, and, also, optimum air pressure at each mine can be determined for its particular conditions."

Jan 1, 1966

By Tony Lipiec, Greg Gosson

"When it comes to new mines being developed, there is a general industry consensus that most low-hanging fruit has been picked. Many projects currently in the mine development pipeline have been around for decades, but were held back because of technical challenges. Future development of these deposits will likely require access to the public capital markets, and in Canada that means providing scientific and technical disclosure on these deposits in compliance with NI 43-101. As many of these “challenged” projects have metallurgical issues, the companies that own the projects need to ensure their metallurgical Qualified Persons provide transparent disclosure regarding proposed solutions to those issues.This paper provides an overview of the disclosure requirements under NI 43-101 that are pertinent to metallurgists, and other Qualified Persons who prepare technical disclosure regarding the metallurgical characteristics of a mineral project. It lists the triggers for a technical report under NI 43-101 and Canadian stock exchange policies, and identifies the sections of the report that should involve input from a metallurgist or process engineer. It briefly outlines new civil liabilities under Canadian securities laws that increase the possible consequences for not complying with the technical disclosure standards.These materials are provided for general information purposes only and do not constitute legal advice. Readers are advised to seek specific legal advice from their own legal counsel in relation to any decision or course of action contemplated."

Jan 1, 2003

By W. F. Harkness, D. Hodgkinson

"A non-destructive testing program was established at Crows Nest Resources (C.N.R.), Line Creek mining operation following an in-service fatigue failure of a front wheel spindle on a large haulage truck.This failure identified a definite need for improvements in the ultrasonic techniques used during the mandatory spindle integrity examinations. Initial investigations using common mining industry ultrasonic examination techniques showed that the smallest detectable cracks were 75 mm in length for the spindle types in service at the C.N.R. site. The Initial findings indicated that inadequate inspection technique design was the cause of the poor performance. To improve inspection reliability it was identified that improved ultrasonic techniques were required. Results using designed ultrasonic techniques were encouraging, with the detection of simulated and natural cracks 12 mm long achieved. The cost benefits associated with the extended spindle life, following the removal of these small fatigue cracks, far exceeded those of the expertise and effort necessary to implement and conduct the N.D.T. program.Introduction During 50 years of evolution, non-destructive testing (N.D. T.) has progressed from a laboratory curiosity to a well accepted and invaluable tool used in the assessment of material integrity. Unlike destructive testing, N.D.T. does not deform or render the material useless. Non-destructive tests may involve many applications, from the determination of a corrosion prevention coating thickness to the examination of a raw material for internal and external deformities.Within the mining sector, highly-stressed components will normally have been subjected to some form of non-destructive test during their manufacturing cycle. These tests are used to ensure the component does not contain material flaws whichmay be detrimental to its service performance.While the component may have assured quality when produced, deterioration by fatigue may occur during an aggressive service life. Large dynamically-loaded components such as haulage truck front wheel spindles are , in particular, prone to this service related problem."

Jan 1, 1987

By Golaleh Riahi

An original method is used to obtain stable nanoparticles of gold-based mono- and bimetallic systems supported on an acidic zeolite. This approach has been applied to PtHY (1wt% Pt) and to bimetallic Pt-AuHY containing 1% of platinum to which is added the amount of gold required to give Au/Pt molar ratios of 20,40,60 and 80%. Metal clusters of Au or Pt-AuHY are formed inside the supercages of the zeolite framework by the thermal reduction of cations by the ligands (en = H2N-CH2-CH2-NH2) under inert gas flow at a temperature depending on the metal. The use of acidic zeolites favours the dispersion of the metal and the thermal stability of the particles. This stability is explained by chemical anchoring of metal clusters by the Brønsted sites of the support. Several techniques have proved that for a molar ratio of 20% metal particles of Pt-AuHY are bimetallic. The segregation of Pt and Au starts for molar ratio =?40%. The catalysts tested on the methylcyclopentane hydroconversion reaction reveal that the addition of gold to platinum leads to an increase in the activity and an improvement in the selectivity for isomerization of the skeleton (cyclohexane and benzene) to the detriment of hydrogenolysis. Similar results were obtained for the dodecane isomerisation to isododecane. These catalysts were also tested in CO, propene and propane oxidation. The activity of fresh catalysts is rather low. It increases after their pretreatment in oxygen or hydrogen atmosphere. In propene oxidation in the reaction mixture O2 ? H2, beside total oxidation of propene to CO2, also propene hydrogenation was observed, particularly at low temperatures. The presence of Au enhances the hydrogenation properties: high selectivities (> 90%) to propane and high propane yields on PtAu HY are observed up to ~150oC, whereas for Pt HY catalyst the selectivity and yield to C3H8 decreases rapidly with the temperature beginning from ~100oC.

Oct 1, 2003

By Chenming Liu, Xiao Lin, Bo Wang, Hongbin Cao, Xingang Li

Over 2 million tons of NH3-N were discharged in China per year recently, rare earth industry contributed 7.03% of NH3-N pollutant from industrial wastewater in 2007. Wastewater containing NH3-N and heavy metals mainly produced in RE extraction saponificated with ammonia and precipitated by ammonia bicarbonate. Generally, 1 ton REO cost 0.6-1.2 ton ammonia for extraction and 1.6 ton ammonia bicarbonate for precipitation, and produce 35-100 ton wastewater. Processes, like Na-saponificated, Ca-saponificated and Non-saponificated technique, are widely studied to reduce the adverse environmental effect of RE industry, while traditional processes still have advantage in production cost, process stability and product quality. In this study, a novel process that combines distillation and air-stripping is developed. NH3-N is removed and recovered based on relative volatility difference of NH3 and H2O. Phase equilibrium, heat equilibrium are calculated to determine process parameters. Hydrodynamic performance like flow field distribution is also simulated. Then, design parameters for distillation trays or structured packing are determined based on calculations and simulations. Besides, the phase diagram of (NH4)2SO4-NH4Cl-H2O in 30°C - 100°C, the typical salts composition of nonferrous wastewater, is studied to ensure commercial plants’ continuous operation. Ammonia removal tower (ART) with different high efficient column internals is designed to fit RE wastewater treatment requirement. The novel process has been commercialized in RE industry in Jiangxi, China. The commercial project operation results show the novel process reached a nearly zero-emission with >99.5% NH3-N was removed and then recovered as ammonia. Combined the novel process, the traditional REO separation process using ammonia and ammonia bicarbonate could achieve NH3-N reuse and the effluent quality meets the discharge standards.

Jan 1, 2016

By Ray Mason

Marathon PGM Corporation?s PGM-Cu Project in Northwestern Ontario (Figure 1.0) serves as a case study to describe the process involved in advancing a deposit from grass roots exploration to the completion of several feasibility studies and the parallel commencement of environmental permitting. Through the following examination of historical exploration activities, it is clear that these activities are directly related to economic stimulus, mostly measured by downturns in the mineral industry. Other factors that influence the success of exploration advancing to feasibility and new mine development includes the ownership of the mineral claims, which also changes under these economic influences and the crucial role of interactions between the Company, the Crown and First Nations. The Marathon PGM-Cu deposit is hosted within the Eastern Gabbro Series of the Proterozoic Coldwell Complex, which intrudes and bisects the much older Archean Schreiber-Hemlo Greenstone Belt. The sub-circular complex has a diameter of 25 km and a surface area of 580 km2 and is the largest alkaline intrusive complex in North America (Walker et al., 1993). Mineralization at the Marathon PGM-Cu deposit is part of a very large magmatic system that consists of at least three cross-cutting intrusive olivine gabbro units that comprise the Eastern Gabbro Series of the Coldwell Complex (Figure 3.2.4-3). In order of intrusion, the three gabbroic units consist of (1) Layered Gabbro Series, (2) Layered Magnetite Olivine Cumulate (LMOC) and (3) Two Duck Lake (TDL) Gabbro. The relative size and abundance of the gabbroic units decrease in the order Layered Gabbro Series>TDL Gabbro>>LMOC. Late quartz syenite and augite syenite dikes cut all of the gabbros but form a minor component of the intrusive assemblage.

May 1, 2010

By Evelynn Stirling

"The paper/presentation will review the evolution of diesel technology from older diesel engines (1990 vintage) through to the latest technology as a result of the ever changing emissions regulations. It will encompass the EPA Tier levels as well as the latest Euro Stage V emissions. The next step with technology will be to address the CO2 emissions, which translates to improving fuel efficiencies of the product as well as other technologies like battery electric, hybrid and fuel cells. As technology progresses it also becomes important to improve connective diagnostic systems to support maintenance practices and improve efficiencies. What will also be presented will be the key emissions changes to the different gaseous and particle mass elements as the products have transitioned from the EPA Tier 3 through to Tier 4 Final regulations. Offering a range of different technologies to the underground mining market matters as not all pieces of equipment will perform optimally due to its duty cycle and application. INTRODUCTION Rudolf Diesel built his first well-known prototype of the high-compression engine in 1897. Since that time, the diesel engine has evolved into one of the world’s most capable and reliable forms of power generation. Diesel engines can be found in a wide variety of vehicles and equipment, powering everything from agriculture and construction equipment to power generators and marine vessels. In the early days the emissions from diesels was very poor and extensive work has been accomplished over the decades to make the product more environmentally friendly. This is more important in underground mining where the space is limited and ventilation is expensive and challenging. DISCUSSION The key driver of the development of diesel technology is the legislation globally around engine emissions. The emission level requirements over the years has forced diesel engine manufacturers to build a deep technical understanding of the system and how to innovate and optimize key elements of the engine. Cummins expertise has been built over the years as the diesel engine has evolved from a relatively simple mechanical engine to an electronic system with advanced air handling, fuel system, after treatment, and controls. Cummins has also continued to expand into systems beyond diesel, including natural gas. Many new components have been added to diesel engines to reduce emissions while improving fuel efficiency and reliability and, at the same time, reduce the total cost of ownership to the customer."

Jan 1, 2019