Search Documents

By H. W. Leon, F. J. Ellis

"This paper covers the new six-strand curved-mould billet casting machine at the Contrecoeur Works of SidbecDosco. It commenced production of 3 Yz-in. square billets at the beginning of January 1972. Together with two 100- ton ultra-high-power electric furnaces in a new meltshop, it is the principal source of billets for the existing rod and bar mill also located at Contrecoeur. The paper develops the reasoning for casting-to-size 3Y2 -in. billets and for choosing a six-strand machine. It indicates the significance of Sidbec-Dosco Montreal Works' extensive experience in operating a four-strand curvedmould billet machine since 1965 and the ways in which this experience influenced the design and operation of the new caster. Machine features are described in detail, as are the reasons for some of the features. The installation, checkout and crew training are briefly discussed as well as the tundish teeming trials. The first cast on January 5, 1972, is covered and a log is shown of the first casts to an empty ladle. There are operating statistics covering the first 100 casts, which produced 8000 tons of good billets in ten weeks of operation. Machine performance and billet quality were good and the few minor problems encountered are described."

Jan 1, 1973

By Michael L. Free, Zongliang Zhang, Joshua M. Werner

In the copper electrowinning process, short-circuiting between the anodes and the cathodes is a critical problem that changes the current allocation among local electrodes and reduces the current efficiency significantly. Possible reasons for the short-circuiting include the improper alignment of the electrode, bent electrode, and nodules on the cathode surface. In typical tankhouses, there is often a time between shorting and harvesting as well as between shorting and clearing. Therefore, it is inevitable to have short-circuiting affect the operation performance in practical electrowinning operations. However, one key piece of missing data is the actual measurements of the current efficiency as short-circuiting is approached and allowed to continue. Consequently, short-circuiting tests that allow tracking of electrowinning parameters before and after short-circuiting were performed in a laboratory scale Cu electrowinning cell. In the tests, the electrode spacing change, the mass of electrodeposited Cu, the deposition morphology, and the current allocation as well as the current efficiency before and after short-circuiting were studied. Results show that the short- circuiting affects the current allocation and the current efficiency significantly. Moreover, it changes the Cu deposition on the short-circuited cathode and therefore causes problems for Cu electrowinning. INTRODUCTION Electrowinning (EW) is commonly used for copper production around the world, with a rated production from 120,000 to 200,000 tons per year per operation (Wiechmann, Aqueveque, Henríquez, Muñoz, & Morales, 2014). In Cu electrowinning, Cu ions in the electrolyte are reduced on the cathode surface as metallic copper with a DC current, while on the anode, a counter anodic reaction occurs with oxygen gas generation (Werner, Zeng, Free, Zhang, & Cho, 2018; Zhang, Werner, & Free, 2018; Zhang, Werner, & Free, 2018). In copper electrowinning, an average current density of 200 to 400 A/m2 is applied to the electrowinning cell (Wiechmann et al., 2014). As the Cu deposits on the cathode, the distance between anode and cathode reduces and most of the time, short-circuiting forms between some anodes and cathodes in a large tankhouse containing thousands of electrodes, reducing the current efficiency and increasing the energy consumption significantly. The current efficiency in well-run copper EW operations is typically above 90 %. Most of the unused current is wasted through short circuits, stray currents, and by-byproduct formation (Davenport, King, Schlesinger, & Biswas, 2002; Wiechmann, Vidal, Pagliero, & Gonzalez, 2002; Wiechmann, Morales, & Aqueveque, 2010). Usually, in the tankhouse, the short-circuiting increases the current in the involved cathode by up to 1500 A (Wiechmann et al., 2010). Multiple reasons can cause the short-circuiting in the cell, and the most common reasons include the uneven current distribution among cathodes, tilted electrodes, bent electrodes, and nodules formed due to the large deposition roughness. Recognition of this challenge in the Cu electrowinning process has led researchers to perform many investigations on approaches to avoid and reduce the short-circuiting in the cell. A series of research investigations have been conducted to develop and improve a new type of intercell bar for Cu electrowinning (Wiechmann et al., 2002; Wiechmann, Morales, Aqueveque, & Burgos, 2007; Wiechmann, Morales, & Aqueveque, 2009; Wiechmann et al., 2010; Wiechmann et al., 2014). The associated test results show that this new design limits the occurrence and magnitude of short circuits and allows operation at higher current densities. Sandoval, Clayton, Dominguez, Unger, and Robinson (2010) stated several keys to control short circuits, such as maintaining the straightness of the cathode, removing “edge hair” from the cathode starter, and maintaining electrode alignment in the cell. Prengaman and Siegmund (1999) from RSR technologies developed a new Pb-Ca-Sn anode to prevent the anode deformation, thereby reducing the short-circuiting in the Cu electrowinning cell. Although the negative effects of short-circuiting on the Cu electrowinning have been recognized, and various investigations have been conducted to address this issue, the actual measurements of the electrowinning behavior and performance as short-circuiting is approached and allowed to continue are seldom reported. However, in typical tankhouses, there is a time between when shorting occurs and harvesting/clearing are performed. One key factor in determining the harvest time is the frequency of shorting. Consequently, we have performed short-circuiting tests that allow us to track electrowinning parameters before and after short-circuiting.

Jan 1, 2019

By R. F. Neider, W. R. Bain

"Expanding upon one aspect of a recent paper on ""Fluid Column Roasting at Sherbrooke Metallurgical Co. Ltd.,"" the present paper deals with the operation of the fluid column process to achieve substantial elimination of cadmium and lead during the roasting of pelletized zinc concentrates. Designed to meet the need for additional feed for Matthiessen and Regeler Zinc Company's vertical retort zinc smelter in West Virginia, without recourse to a sintering operation, the plant is capable of simultaneously attaining very low lead and cadmium levels on demand, through operation in the manner described. Fluidizing air admitted via the wind box is supplemented by natural gas admitted via a tuyere bank 15 ins. above the hearth, in quantities adjusted to maintain a reducing atmosphere within the interstices of the bed. In addition, careful attention is paid to bed temperatures, which run from 1,080° to 1,100°C. Under these reducing conditions, 90 per cent of the cadmium and 92 per cent of the lead in the feed are eliminated, the sulphate sulphur content is decreased by 0.5 per cent, sulphide sulphur is held at 0.6 to 0.08 per cent, and the zinc content correspondingly in-creases. The fuel value of the natural gas is recovered as extra steam, which carries a credit. There are some added difficulties with fume accretions, gas conditioning and gas -cleaning, some of which have yet to be overcome."

Jan 1, 1967

By J. I. Gazzarri

A model of solid oxide fuel cell AC impedance behaviour has been developed and is used to simulate the frequency response of a single cell with and without mechanical damage. The results indicate that the presence of mechanically induced damage within the components of a solid oxide fuel cell can be detected by comparing the frequency response of the undamaged cell with that of a cell in which in-plane cracking or delamination has occurred. The presence of such defects manifests itself as a new semicircle in the Nyquist impedance diagram of the full cell. A parametric study reveals the resolution capabilities of the method in terms of the geometrical characteristics of the defects.

Jan 1, 2005

By Scott Beer

What New Technologies Will Drive Economic Improvements? ??Historical ?1060?s: Mainframe Technologies ?1970?s: Mini Computing ?1980?s: Workstation Computing ?1990?s: Personal Computing ?2000?s: Network Computing Internet PDAs Cellular phones ??What?s the next technology improvement? ??What?s next for Mining?

May 1, 2009

By M. Turek

Cost management in the conditions of increasing competition and unforeseen market turbulence constitutes one of the key areas of the enterprise?s activity. In the last two years the demand for hard coal on the domestic and global market of non-renewable resources has increased significantly. Polish hard coal mining industry, as an industry in the stage of decline, received a chance for rejuvenation. However, one of the most significant conditions of seizing this opportunity is the rationalization of mining costs and improvement of production effectiveness. Due to the significance of this issue, the main objective of the paper is to identify the possibilities of improving the production effectiveness in the hard coal mining industry. In order to meet such an objective, in the first part of the paper we measured effectiveness in the Polish hard coal mines in years 2006- 2011. The research encompassed three out of five mining enterprises operating in the country. Then based on the received results, guidelines concerning the improvement of effectiveness of production were created, taking into consideration infrastructural, technical, economic and organizational determinants. Furthermore, opportunities and threats for improving the production effectiveness, stemming from the external conditions have also been indicated.

Aug 1, 2013

By L. Magne, A. Pinto, M. Maldonado, J. A. Finch

Estimation of gas holdup from electrical conductivity measurements has been used in lab and industrial installations. The approach is based on the application of Maxwell's model, which relates the concentration of a dispersed phase in a continuous medium to measurements of the electrical conductivity of the dispersed phase, continuous medium and the resulting mixture (dispersion). When applied to inferring the collection zone gas holdup in a three phase system and to facilitate real-time on-line measurement, the slurry is assumed to behave as the continuous medium and gas bubbles as a nonconducting dispersed phase. This article derives an equation for estimating gas holdup in a three phase system, eliminating the assumption that the slurry behaves as a continuous medium but rather as a dispersion of non-conducting solid particles in water. In this formulation only water behaves as the continuous medium in the sense of Maxwell, and gas holdup in a three phase system is then calculated from the application of the Maxwell model twice: (1) to determine solid content in a two-phase system, and (2) to determine solid plus gas holdup in a three phase system. To validate the new equation and quantify the errors incurred by assuming slurry is the continuous phase a laboratory flotation cell was instrumented to continuously measure the conductivity of two and three phase dispersions with known solids contents. As the amount of gas in a lab flotation machine is difficult to measure directly or by another indirect technique such as using pressure signals, 2.5 mm dielectric plastic spheres having a density of ca. 1.3 g/cm3 were used instead of air bubbles for validation. Experimental results demonstrated that the continuous medium assumption underestimates gas holdup and that the resulting bias error increases linearly with the solid content and decreases with the magnitude of gas holdup.

Jan 1, 2016

By K. Bowes, M. D. Maley, R. J. Ring

The Honeymoon Uranium Project is an acid In-Situ Recovery (ISR) mine in South Australia. It was previously operated for approximately 18 months before being placed on care and maintenance in 2014, it was then acquired by Boss Resources in 2015. Boss has been performing a number of studies to plan for reopening of the mine, including a successful field leach trial (FLT) in 2017. The current configuration for uranium precipitation at Honeymoon is a batch process. Whilst this achieves effective uranium recovery, the precipitates produced are often very fine, with poor settling and solid/liquid separation characteristics. Continuous precipitation, involving recycling of solids, has reportedly been successfully utilised in other operations to increase the particle size and density of the product, leading to solids that can be more readily dewatered, dried and drummed, with less fines and dust generation. However, no operational data are available from such operations.

Jan 1, 2020

By Michael J. Beus

The National Institute of Occupational Safety and Health-Spokane Research Laboratory (NIOSH-SRL) have developed a Shaft Conveyance Monitoring System (SCMS). Assessment of current hoisting technology has shown that monitoring wire rope tension and conveyance position and load directly from the skip or cage top offers several significant safety, production, and maintenance advantages. The SCMS consists of conveyance position and guide displacement sensors, a battery power supply and charging system, and a new sensor to measure hoist rope tension. This device provides a warning of the occurrence of ?slack rope? a particularly dangerous condition. A 2.4 GHz radio link transmits data to the hoistroom. A reduced scale hoisting test facility has been constructed to test these components prior to field trials. The advantages of monitoring wire rope tension and conveyance position and load directly from a skip or cage top will be discussed. Field tests are underway in full-size shafts to refine the concept and evaluate long-term reliability and maintenance requirements. Application of this technology may result in decreased maintenance costs as well as safer, more productive hoisting operations.

May 1, 2001

By V. V. Zubkov

The systems of geophysical monitoring have been already put into operation at coal mines and ore mines. Since at present it is rather difficult to conduct mine experiments; it is necessary to start a new step in joining of geomechanics and seismic. The linking geomechanical and geophysical monitoring at coal mines and ore mines today became possible due to progress in development of numerical methods of modeling of stress state and technology for processing of seismic information. This paper describes one potential step in linking geomechanical and seismic monitoring at coal mines and ore mines.

Aug 1, 2013

By Ralph Harris, Javier Jara

"Oxygen is essential in gold cyanidation. It is supplied to the leaching media by sparging oxygen or compressed air into the cyanidation tank. The rate of oxygen transfer is critical to achieve the desired oxygen concentration in solution.The performance of a novel device for gas sparging recently developed at McGill University is compared to the mass transfer characteristics of the two spargers most used in the gold industry: the four lance configuration and the inverted cone. The distribution of gas and the kinetics of oxygen desorption of the three types of spargers was studied in a 140 litre tank. The oxygen dissolution of the new device is three to five times faster than the other spargers. This could increase the leaching rate and/or decrease the cyanide and oxygen consumption.IntroductionIn hydrometallurgical processing, it is often necessary to bubble gas through a pulp to carry out the wanted reactions. The gas can act to agitate the pulp and it can also supply reactant. The rates of the reactions which require a reactant supplied by the gas are often dependent on the rates of mass transfer from the gas to the solution.A common example of this is gold cyanidation which requires oxygen for gold dissolution. Since the gold containing slurry is rich in other oxygen consuming substances (sulphide like pyrrhotite), it is important to provide enough oxygen to allow complete gold dissolution within the residence time of the cyanidation reactors. It has been demonstrated that the rate of gold dissolution is directly proportional to the dissolved oxygen concentration of the pulp which in turn is proportional to the oxygen partial pressure in the bubble 1 2 3. Improving the rate of mass transfer of oxygen increases the dissolved oxygen concentration of the slurry and therefore improves the rate of the reaction.The rate of mass transfer from a bubble to its surrounding solution increases with decreasing bubble size and increasing gas bubble residence time which in turn increases with decreasing bubble size. The generation and dispersion of small bubbles is thus critical to achieving high rates of mass transfer. Different configurations and devices used to inject gas have different effects on the bubble size and the residence time, influencing the overall rate of mass transfer. Therefore better mass transfer can be achieved by adopting a more efficient method.The methods tested in this report are the four lance configuration (wall spargers), the inverted cone and a new device, designated HCD. The wall spargers and the inverted cone are used widely in the industry today."

Jan 1, 1994

By Hrayr Agnerian

The fair market value of an exploration property is determined by its potential to host a mineral deposit. This potential is gauged by the results of previous exploration, exploration stage, meaningful past expenditures and remaining targets that are not yet tested. Values of exploration properties can be viewed as distinct points in a three-dimensional space defined by orthogonal axes, namely: Exploration Stage (x-axis); Cumulative Expenditures (y-axis); and Property Value (z-axis). In general, these values are estimated by applying activity factors on previous exploration expenditures, e.g. an activity factor of 100% for an active property with good potential and a factor of 50% for an active property but past expenditures have not upgraded the property. At certain periods, a market factor may also be applied to reflect the activity of mineral property acquisitions. For properties that do not exhibit any exploration potential, only nominal values are applied.

Jan 1, 1996

By J. D. Corbett

The spatial coincidence of the seven anomalies is obvious, even though the self-potential is offset northward. Because the ratio, as an indicator of conductivity, is a relative estimate at best, concise interpretation is limited in almost every instance to the location of a conductor or conductor axis. When related to the initial phase of an exploration program, magnitudes and ratios similar to those obtained from any one of the methods described, would be sufficiently attractive to warrant further investigation. The compilation shown is an empirical comparison of actual field results and no emphasis has intentionally been placed on the relative merits of one method in respect to another. Too many additional factors, i.e., size, depth and conductivity of overburden, etc., that cannot unequivocally be answered, enter into such a comparison before a relative evaluation can be made.

Jan 1, 1961

By M. Walawalkar, C. K. Nichol, G. Azimi

Rare earth elements (REEs) are essential to the production of technologically advanced products, including wind turbines, electric and hybrid cars, automotive catalytic convertors, hand held electronic devices, and military defense systems. Their application in environmentally beneficial technologies puts them at a high priority for ameliorating environmental concerns. Because of their increasingly high demand and limiting resources, it is highly beneficial to find new sources for them. The present study is focused on leaching REEs from a phosphate based fertilizer by-product, known as phosphogypsum (PG). Global estimated world production of PG is about 240 million tonnes that is stored in the form of wet stacks adjacent to fertilizer production facilities, occupying vast amounts of land. PG also contains trace metals, which are detrimental to the environment, and hence it is crucial to monitor these stacks. We obtained our PG sample from Agrium Inc. (a fertilizer manufacturing company in Canada). We performed a comprehensive characterization of the PG sample and found that it predominantly contains Y, La, Ce, Nd, and Sm. For leaching purposes, we used hydrometallurgical acid leaching techniques. We investigated three acids over a range of operating conditions such as acid concentration, temperature, solid-to-liquid ratio, and residence time. We achieved an average leaching of 81% with hydrochloric acid as leachant using operating conditions that can be easily replicated in industrial settings. If our process is implemented, not only will it reduce the size of the existing PG stacks (mitigating their environmental risks), but also enable the development of new innovative routes for extracting REEs, making countries like Canada less vulnerable to supply disruptions.

Jan 1, 2016

By X. -G. Chen, J. Qin, K. Liu, D. Racine

"Understanding the thermo-mechanical fatigue (TMF) behavior of materials plays a significant role in the safety design of critical components used in aerospace and automotive industries, such as engine blocks and cylinder heads, which undergo the cyclic change of temperature and stress. However, the cyclic changes of temperature, stress and strain make it difficult using the traditional testing methods to accurately simulate the TMF process. In the present work, the Gleeble® 3800 system was successfully applied to develop a reliable procedure to measure the TMF behavior of aluminum alloys. The modified setup together with the new designed program allows the Gleeble system to precisely simulate the cyclic profiles of temperature and mechanical strain. The novel procedure includes the calibration and verification of the TMF setup to ensure the test validity with Young’s modulus measurement, multi-cycle measurement of the thermal strain and zero stress adjustment followed by online monitoring the TMF cycles. The results of the TMF testing of an AA6061 alloy under cyclic temperatures (60–300°C) and various strain amplitudes (0.2–0.6%) were demonstrated. Its TMF behavior was characterized by the typical hysteresis loops and cyclic stress-strain response.INTRODUCTION The thermo-mechanical fatigue (TMF) behaviour becomes increasing important to evaluate the elevated-temperature properties of materials used as the critical components in automotive and aerospace industries, such as the gas turbines (Hu, Shi & Yang, 2016; Moverare, 2007; Segersäll et al., 2015) and engine blocks (Grieb, Christ & Plege, 2010; Javidani & Larouche, 2014). During the cycles of start-up and shutdown of the engines, these components undergo a complex change of loading. Meanwhile, a dramatic temperature gradient exists on the components due to the cooling system. Therefore, the cyclic changes of load and temperature can give rise to the TMF and may limit the use life of such components (Hu, Shi & Yang, 2016; Javidani & Larouche, 2014; Moverare, 2007). Hence, performing the TMF tests to precisely simulate the cyclic changes of load and temperature to understand the TMF behaviours of materials is playing a significant role in the safety design of these components. For TMF tests, two principal types of cycles are generally employed, including the in-phase (IP) cycle where the load and temperature are at the same phase (i.e. maximum load at highest temperature) and out-of-phase (OP) cycle where the maximum load is applied at minimum temperature (Kliemt, 2012; Miller, 2014). The most significant damage mechanisms in engine components are reported to be OP TMF cycles (Javidani & Larouche, 2014; Kliemt, 2012)."

Jan 1, 2018

By D. S. Flett, A. V. Tolstov, M. A. Mulagaleeva, N. V. Gudkova, A. M. Zhizhaev, V. I. Kuzmin, Institute of Chemistry and Chemical Technology SB RAS, O. A. Logutenko, V. N. Kuzmina

The complex niobium-rare earth pyrochlore-monazite-crandallite ores of the Tomtor deposit, located in the Siberian Arctic, should be considered as a new type of rare metal materials. The major valuable components of the ore are niobium, rare earth elements, yttrium, and scandium; associated components are titanium, vanadium, aluminum, and phosphorus. Because of the irregular distribution of the rare earth metals and niobium according to grain-size, the extremely finely dispersed nature of the minerals and their close interpenetration to each other, ore processing by gravitation and flotation is not successful. The processes studied for the treatment of the Tomtor ores use direct alkaline-acid leaching to open the ore. A problem in the first stage of alkaline leaching is the high aluminum content, which decreases the activity of sodium hydroxide and alkaline-earth metals, which are bound to phosphorus. Ore processing using alkaline-nitrate and alkaline-chloride leaching was proposed and investigated. The first variant was used to obtain rare earth and scandium materials and a niobium-titanium concentrate, which can be a stock material for processors who use chlorination for the processing of ores and concentrates. The second variant is a complex advanced ore processing scheme with electrochemical regeneration of the waste chloride solutions obtaining sodium hydroxide, hydrochloric acid, and chloridizing agents. Moreover trisodium phosphate is used for purification of the waste mother liquors from metal cations. The complex salt, NaAlCl4, is proposed as the chloridizing agent for the decomposition of the niobium-titanium concentrate.

Jan 1, 2016

By A. Longval, Q. Jiao, T. Shannon

In 2000, Xstrata Zinc (former Falconbridge Ltd.) Brunswick Smelter commissioned a modified lead blast furnace. Since then, efforts have been made to improve its operation in order to achieve optimal operation in terms of coke consumption, lead loss to slag, and improved environmental and hygiene conditions. This paper will review the important step changes in operational philosophy, undertaken since 2004, for the control of the blast rate, oxygen enrichment in blast, slag chemistry and charge level. Furthermore, a review of the improvements made in secondary materials consumed at the blast furnace will be made. This paper will also discuss the significant reduction of the frequency of accretion removal as a result of improved furnace operation.

Jan 1, 2008

By Chuan-Jian Zhong

Gold-based nanoparticles in the size range of a few nm have attracted increasing interests in catalysis, sensors and biomedical applications. The study of the unique catalytic properties of nanosized gold was inspired by the pioneering work of Haruta on the nanogold-catalyzed CO oxidation (1-4). There have been a number of excellent reports discussing both fundamental and application aspects of gold nanoparticles in catalysis (3-8). Our work reported herein is aimed at investigating the preparation and application of gold and its alloy nanoparticles for potential applications in fuel cell catalysis. Fuel cells operating by electrochemical oxidation of hydrogen or methanol fuels at the anode and reduction of oxygen at the cathode are attractive power sources due to their high conversion efficiencies, low pollution, lightweight and high power density. While methanol offers the advantage of easy storage and transportation in comparison with hydrogen fuel cell, its energy density (~2000 Wh/kg) and operating cell voltage (0.4 V) are much lower than the theoretical energy density (~6000 Wh/kg) and the thermodynamic potential (~1.2 V). The poor activity of the anode catalysts and inefficient activity or issue related to "methanol cross-over" at the cathode electrode are associated with the loss of about one-third of the available energy at the cathode and the other one-third at the anode. Extensive studies have been focused on Pt-group metals (Pt+Pd+Rh+Ru+Ir (PGM)) for both anode and cathode catalysts. A major problem is the poisoning of Pt by COlike intermediate species (9,10). Recently, oxide-supported gold nanoparticles in the <10 nm size range have emerged as one of the best catalysts for CO oxidation (1-3,11), and for water gas shift reaction in reforming stage using 5 nm Au on Fe2O3 (6). Gold and its alloy with other metals in the nanosize range present new alternatives (2,12). Whether the unique properties of gold nanoparticles can be exploited for addressing these problems is a focus area of our work. The ability to harness the large surface area-to-volume ratios and the unique surface sites of nanoparticles in <10 nm size range, especially in heterogeneous catalysis, constitutes a major driving force in fundamental research and practical applications of nanoparticle catalysts. It is this size range over which the metal particles undergo a transition from atomic to metallic properties. The understanding of factors controlling the morphological and surface reconstitution associated with such a size range is of fundamental importance to the ultimate exploration of nanostructured catalysts. We have been investigating the interfacial structures and properties of core-shell types of nanoparticles consisting of gold or alloy nanocrystal cores and organic monolayer shells that were prepared by twophase synthesis (13) and processing (14) protocols. Important attributes of such nanoparticles include controllable size monodispersity, processibility, and stability towards size- and composition-tunable catalysis (15-21). Some of these attributes were studied for understanding their electrocatalytic properties in the oxidation of methanol and reduction of oxygen, which are of fundamental interest to fuel cell technology.

Oct 1, 2003

By D. R. Murray

"In 2017, Nutrien Allan Potash remediated a portion of the concrete liner in the production shaft. A set of underslung work platforms and collection boxes were used in conjunction with hydraulic splitters, jackleg drills and hand chippers to excavate and remove the broken concrete. New concrete was placed with the original pressure relief design, using a shaft slip form. Shortly after excavating, it was found that the estimated breaking rate and amount of original concrete in-situ was under estimated. Fifteen feet of excavated concrete (2719cu.ft) and ten feet (of replaced concrete was completed on April 28, 2017, and operation of the production shaft was returned to mine operations. During February 2019, Nutrien Allan Potash began remediation of a portion of the concrete liner in the service shaft. The project is different than the 2017 project, as the remediation has occurred during normal running operations and occurred only on night shift. Rather than hydraulic splitters and hand chippers, the new method includes a concrete saw and mechanical excavator from a working platform. The selected method is based on the lessons learned from the 2017 project in the production shaft. The service shaft project was scheduled to be completed in July, 2019. INTRODUCTION Nutrien Allan Potash is located approximated 75 km east of the city of Saskatoon, Saskatchewan, Canada. There are currently two shafts at Nutrien Allan Potash: the Production Shaft and the Service Shaft, transporting people and material from surface to a depth of 3,335 ft. The Production Shaft was completed in 1967, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1605 and 2037 ft Levels. A second set of cast iron tubbing was installed in the Duperow formation between 2203 and 2463 ft Levels in 1999. The remainder of the concrete as of todays standards is designed as a pressure relief liner. The Service Shaft was completed in 1968, with one section of grey cast iron tubbing installed in the Blairmore formation between the 1600 and 2048 ft Levels. A second set of cast iron tubbing was installed in 1981, with 169 ft installed through the Duperow formation. The remainder of the concrete as of todays standards is designed as a pressure relief liner. PRODUCTION SHAFT REMEDIATION During the second quarter of 2015, the Mine Engineering team were notified of an area of concern in the production shaft. The shaft specialists of Golder Associates Ltd (Golder, formerly Alan Auld Canada) were contacted to complete an inspection of the production shaft liner with emphasis on the area of concern. Based on the inspection and documentation review, it was determined that the concrete at the 2804 foot elevation had been broken out for some time and was retained with #8 rebar bolts with resin encapsulation. The broken concrete was encroaching on the clearance to the conveyance."

Jan 1, 2019

By E. C. Goodhue, R. D. Coleman, I. E. Puddington, A. F. Sirianni

Iron ore samples containing apatite are fractionated to acceptable products by spherical agglomeration methods. The phosphorus is upgraded by a factor of 10 at an elevated pH. High-grade iron products are obtained in good yields from the tailings in a second step of the operation. The grade of the phosphorus separated appears to reach a maximum at about pH = 10; recovery of iron decreases below about pH = 4. Both the recovery and grade of iron are found to be reduced sharply above about pH = 8.

Jan 1, 1968