Search Documents

By Q. Chen, J. H. Zhang, M. Zhang, F. M. Zheng, Y. J. Zhang

The characteristics of air bubbles and gas dispersion in KYF flotation cell are studied using the method of the point conductivity probe and CFD simulation. With increasing of speed, the velocities of air bubbles increase slowly and the distribution of diameters exhibits little change. With increasing of aeration rate, the gas holdup is increased. However, the velocities and diameters of bubbles have no great change. The CFD predictions on gas holdup have good agreement with the experiment results. The gas holdup distribution in the center section is revealed. The gas dispersion in the middle and upper part of flotation cell is uniform. It would be helpful for bubbles and solid particles collision. The gas holdup of the lower part of flotation cell is scarce, and it agrees with the observation in experiment. The gas would accumulate at the suction side of impeller blades, and it would decrease the power consumption. The rotating speed and aeration rate have great effect on gas dispersion. With increasing of aeration rate, the gas holdup of flotation cell will increase. The increasing of speed would improve gas dispersion. The results are expected to help to optimize the performances of KYF flotation cell.

Jan 1, 2015

By Saikat Chatterjee, Xintong (Brett) Liu, Kinnor Chattopadhyay

Magnesia carbon bricks are commonly used in BOFs and are generally pre-heated before the BOF goes into service. Owing to very stringent emission regulations, the BOF pre-heating process need to be controlled and optimized so that, the emission standards are met. One of the major concerns in organic emissions are its stringent limits on emission rates and total volatile emissions. In the present work, an attempt has been made to integrate CFD and Thermodynamic models to predict the emission rate of volatile organics during the pre-heating process. A one dimensional heat transfer model was developed using visual basic and then integrated with thermodynamics calculations using FactSage 6.4. The parameters that affected organic emissions were the pre heating procedure, gas composition of the burner, heating rate and type of the burner. Typical composition of MgO-C bricks and binder materials were obtained from literature and vendor data sheets. Chemical reactions between organic materials, refractory and burner gasses were considered. The model predictions indicated that certain burner conditions could destroy all organics before it exits the vessel while other conditions needed the use of an after burner at the mouth of the vessel. The model was also able to predict the organic emission rates based on the chosen pre-heating profile. This kind of predictive model will be very useful for the steel industry and enable them to justify permit limit applications and stick to the limits by fine tuning their pre-heating process.

Jan 1, 2015

By Peter N. Blakey, Jean-Paul Paquette, Barton A. Thomson

"FROM THE BEGINNING OF THE PIT, it was known that the surface mining method had a projected life of about ten years, and that the ore extended to depths recoverable only by underground mining. When serious consideration was given to underground mining in 1968, it was realized that tremendous advantages could be gained by starting the underground mine as early as• poss1ble. These included: 1. The availability of underground ore for grade control, which would become more difficult as the pit deepened. 2. The need to develop new systems, equipment and skills to take full advantage of the technological revolution in underground mining. 3. Early knowledge of rock behaviour through trial mining on a small scale prior to finalizing plans for major blocks. In addition, the pit would be available to guarantee the mill supply if problems were encountered. 4. With sufficient time and early mining experience a much better job could be done on all mine planning. Because ample reserves of economic underground ore were virtually assured, the desired underground mining capability became a function of two restraints: first, the time required to excavate and construct the permanent headframe, shaft and ore-handling facilities necessary to handle large volumes of stope ore; second, the time for lateral and stope development on at least one level which would normally follow shaft sinking. The decision made was to move immediately on the permanent hoisting installations and at the same time embark on the planned ramp from surface, which would allow much stope preparation to be completed prior to .bringing the shaft on stream. Both projects were placed on an urgent basis early in 196S' and the following decisions made shortly thereafter."

Jan 1, 1974

By L. Magne, M. Maldonado, R. Varela

Real-time optimization of flotation circuits demands for accurate and reliable measurements to support the decision making process. The collection zone gas holdup is an important variable in this context as integrates the effect of machine and chemical factors on the bubble size and velocity distributions. It has been demonstrated that gas holdup not only correlates with bubble surface area flux, which defines the particle collection rate and recovery in the collection zone, but also with water overflow, a variable which has been related to the froth zone recovery. Therefore, on-line gas holdup measurements provide a reliable alternative to judge efforts leading to the optimization of flotation cells and columns. Estimation of gas holdup in flotation from electrical conductivity measurements has been proposed and extensively used in lab and industrial installations. The approach is based on the application of Maxwell's model, which relates the concentration of a dispersed phase in a continuous medium to measurements of the conductivity of the liquid medium and of the mineral pulp with and without air bubbles included. These measurements require a conductivity cell which covers a representative volume of the flotation cell, and creates a homogeneous electric field throughout this volume that ideally is not affected by the conductivity of the medium. The development of such a cell in the limiting space and geometry of a laboratory flotation cell has been problematic, but a multi-electrode arrangement offers a promising alternative. Electrodes were installed in the flotation cell of a Denver unit; the results of preliminary testing are discussed with a focus on its performance in the measurement of two- and three-phase dispersion conductivity.

Jan 1, 2015

By C. R. Lattanzi, M. J. Davie, L. D. Smith, J. R. Goode

"The feasibility study determines the technical and economic viability of a project at the level of accuracy required by the owner to make an investment decision. The economic analysis usually includes calculation of the discounted cash flow. Key components of the cash flow include the project capital cost, the operating costs, construction schedule, production rate, product prices and financial details.This paper examines the feasibility study for a typical mining project. The paper discusses acceptable methods for the determination of the geological and mineable are reserves. The prerequisites for the development of suitable designs, and the calculation of capital and operating costs for the mine, processing plant, and infrastructure are reviewed. Important features of the cash flow analysis and its interpretation are presented.IntroductionThe commercial development of a mineral deposit invariably requires the investment of capital in preparing the deposit for production. It has always been necessary, therefore, to demonstrate to the investor of capital that production of a saleable commodity is both technically feasible and economically viable. The instrument typically used to make these determinations is the feasibility study .Traditionally, mining companies have been rather conservative in their approach to financial management. Until about thirty years ago, the capital required to develop a new mine was most frequently provided by internal corporate cash now and virtually all of the necessary technical and economic studies were performed 'in house'. Under these circumstances, there was little standardization as to what constituted an acceptable feasibility study, and even less as to what constituted an acceptable measure of economic viability."

Jan 1, 1991

As land resources decrease, commodity prices increase, and technology evolves, deep sea mining is becoming a viable alternative to meet the increasing demand for minerals. Successful deep sea mining operations are built on sound identification of the resource, proper selection of equipment, a thoughtful production plan, and good project management. These four key activities can be further optimized by analyzing how the spatial variability and uncertainty of the ore body properties impact the final mining operation. To address this problem, IHC Merwede is in the process of developing a risk quantification framework in the context of deep sea mining, which makes use of state of the art geostatistical simulation methods and transfer functions to quantify geological uncertainty and translate it into decision or project risk. The paper introduces the Local Average Subdivision method (LAS) for generating simulated models of the deposit and presents a new extension to incorporate point measurements of geotechnical or ore grade properties. Due to its computational efficiency, the presented method is suitable for simulating largely extended sea floor deposits. The second part of the paper illustrates, through example case studies, the significant benefits of a risk based approach which translates geological uncertainty into financial or operational performance indicators. In particular, the focus is on assessing financial project risk and on the design optimization of the deep sea excavation equipment by analyzing cutting forces, specific energies, and power requirements.

Aug 1, 2013

By B. S. W. Buffam

Introduction The development of uranium deposits is a relatively recent phase of mining in Canada. To date, the only producer of uranium ores on a commercial scale has been the Port Radium mine on Great Bear lake, N.W.T. However, with.-in the past few years intensive prospecting has been carried on throughout Canada and many occurrences of uranium-bearing minerals have been discovered. Eldorado has been active in the search for and the exploration of uranium deposits in Canada for a longer period than any other company and has, therefore, accumulated a considerable fund of information, especially about occurrences in Saskatchewan and in the Northwest Territories along the western fringe of the Precambrian Shield. The Company has also had experience in the underground operation, and in the mining, of uranium ores at Port Radium. During the past year or so many requests have been received from the prospecting and mining fraternity for information and guidance regarding the development of the many new uranium discoveries that have been made in Canada. Assistance by Eldorado is freely given whenever possible and this paper is presented to supplement the private discussions and to provide as wide a distribution as possible of the data acquired by Eldorado.

Jan 1, 1951

By H. Pempel, J. Markowski, P. Ay

"Metal-coated thermoplastic parts find more and more functional and aesthetic applications in the interior and exterior of cars. The vapor-deposited or electroplated coatings are usually composed of a plurality of nickel- and chromium-containing layers, which are applied to copper-containing carrier layers on the polymers. Previously, recycling processes are mainly focussed at the recovery or thermal utilization of the plastics. Targeted and selective recycling of the metallic coatings is usually not carried out. Together with several SME, BTU developed a process, in which a complete and separate recovery of all components in high purity is possible with biotechnological methods. The bioleaching is carried out with iron and sulfur-oxidizing bacteria, especially Acidithiobacillus ferrooxidans. The copper-containing layers are dissolved in the solution; chromium- and nickel-containing particles are precipitated as solids. After the bioleaching, a mechanical separation of the individual metal-containing components and their separate workup are carried out. End-products are metallic copper, a nickel- and chromium-containing solid and the cleaned plastics. The bioleaching ensures a high purity of the end products. Through the use of bacteria, which are also found in nature, the process is environmentally friendly. Compared to chemical leaching using inorganic acids, considerably shorter leaching times can be achieved. In addition to the optimization of the leaching process, the R/D-project also includes the development and testing of the apparatus technology.INTRODUCTION The material complexity of many end-user products has increased in recent years, especially in the fields of electrical appliances, vehicle technology and medical technology. However, the demands on functionality, safety, comfort and energy efficiency still play a greater role in product design as factors such as sustainability and usability. For example, if a car still holds more than 70% of steel in the 1980s, a vehicle nowadays includes a larger proportion of a variety of difficultly separable plastics and composite materials, as well as complex metal composites. This relates in particular to composites made from such different materials as metals and plastics. The processing and recovery of the components of those complex material mixtures is difficult for recycling companies."

Jan 1, 2017

By Craig Roberts

"While various methods are available to estimate a mining project's value, value is only established through a transaction. Comparable methods allow the value estimated for a mining project to be benchmarked against mining project values established in the market. Comparable methods thus are a key tool for ensuring value estimates are congruent with what the market would actually pay. For example, if the value estimated for a mining project using discounted cash flow analysis differs significantly from the value implied using comparable market methods, the valuator may be using metal price or discount rate assumptions that differ significantly from those the market is currently willing to pay for.The paper provides an overview of market comparable valuation approaches, and discusses some of the difficulties and limitations that arise in using these approaches. The types of market values that are typically utilised are discussed, including asset sale prices, share prices (market capitalisations), and values established in corporate mergers and acquisitions. Topics discussed include methods used in estimating a mining project's value based on the market value of the company that holds the asset, and limitations that arise because of unique features of mining projects and of companies that hold them.It is concluded that market comparable and fundamental (e.g. NPV) approaches to project valuation should not be viewed as alternative approaches to estimating project value, but rather can and should be integrated to derive a single value estimate based on both market andfandamental data. A method for integrating these approaches is discussed, and illustrated by example."

Jan 1, 2003

By Cummings. J. B., R. Haworth

"THE OPERATION of the Potash Company of America, Ltd., at its plant near Saskatoon, Saskatchewan, is the result of many years of exploratory and development work, culminating in the construction of a shaft, milling, concentrating and other facilities necessary to the production of potash in a marketable form.The possibility that potash existed in •commercial quantities in Saskatchewan was first indicated in 1943, although it was not until mid-1946, when Bata Petroleums penetrated a potash bed at its Verbata No. 2 well near Unity that substantial in-ter.est was developed in the possible exploitation of this important mineral product.The Potash Company of America, which is the largest producer of pot-ash in the Carlsbad, New Mexico area, a district that has been sup-plying about 90 per cent of the North American potash demand, be-came interested in the Saskatchewan deposits •at an early stage. Its engineers made an intensive study of the western Saskatchewan area in 1947 and continued their review of operating problems throughout the next three years.""Potash"" is the commonly used general term applied to the minerals of potassium, of which there are several. The most common mineral forms in which it is produced are potassium chloride and potassium sulphate. The potash content of potassium compounds is ordinarily ex-pressed in terms of potassium oxide (K20) equivalent."

Jan 1, 1960

By B. Courtaud, L. Donati, V. Weigel

As a growing mining company, ERAMET is looking for new positions in the strategic metals market. In this context, the Gabonese Maboumine pyrochlore deposit is currently being studied for the recovery of niobium, tantalum, rare earths and uranium. This ore shows mineralogical and chemical characteristics that make it challenging to process by existing practices, from both technical and economic points of view. ERAMET has developed since 2008 an innovative hydrometallurgical process, which has been successfully operated at a pilot plant scale (more than 35 weeks in continuous). The upstream part of the process aims to dissolve valuable elements in sulphuric acid. The first step is dedicated to dissolve the ore matrix, leaving the pyrochlore unleached. The second step consists in chemically breaking down pyrochlores in order to form soluble species of the valuable elements. After dissolution, the valuable elements are separated into different flows: niobium and tantalum are recovered and transformed as commercial ferroniobium on one side, and rare earths and uranium remain in the solution to be recovered in the downstream part of the process. The main goal of this paper is to discuss the upstream part of the process, which has given successful results.

Jan 1, 2014

By J. Hedderson, J. Starkey, S. Reeves, B. Hilscher

"As ore sorting becomes more common, it is important to quantify its impact on comminution circuits in order to precisely predict its effect on throughput, grind, and mill operating conditions. Since sulphides and other valuable minerals are often softer then the surrounding waste rock, the ore kept by a sorting system is typically softer than the average ore. In order to accurately forecast production, new measurements of hardness need to be performed on the new concentrated mill feed. This paper proposes a methodology to examine this effect quantitatively at an early stage of project development using the SAGDesign test.INTRODUCTION The application of ore sorting in the mining industry is one of the most promising recent technologies with the potential to cause step change in the way concentrators are designed. Most typically, ore sorters are used to sort a given ore flow for grade, either to reject waste from the mill feed, or rescue ore from the waste pile. Ore sorting technologies have been successfully applied at many mining properties in various forms and while the technology has reached or is reaching maturity in other industries, it is still in development in the mining sector. As a result, there is not yet a general consensus on the considerations that need to be made when designing a plant with ore sorting from a feasibility level above and beyond what is commonly performed as best practice. This paper will discuss those considerations and propose a methodology for integrating ore sorting into a comminution circuit at the design phase. Due to the linearly additive nature of the SAGDesign Test results, a “hardness balance” can be developed to estimate the ore hardness which would be measured in any sorting mass split using only two data points. This will allow a design engineer to make more informed decisions as to the most appropriate mass split to select in relation to the incurred operating costs and grinding circuit sizing."

Jan 1, 2019

By K. C. Hendrick

The paper will review the significant developments in world copper over the past ten years and their impact on the Canadian industry. It will also examine the outlook for the future.

Jan 1, 1971

By B. Chambers, M. Yunovich

"Corrosion monitoring is commonly used in a variety of industries as a means of effective corrosion control programs to extend the life of the asset and ensure safe operation of the facilities. The majority of the monitoring tools have limitations and tradeoffs – e.g., sacrificing the longevity of the probe for higher measurement resolution. Linear polarization resistance (LPR) probes have the advantage of providing the operator with accurate, real-time corrosion rate data; however, the probes can only be deployed in conditions where the measured environment possesses certain minimal conductivity. In many instances, utilization of LPR probes in conditions with intermittent wetting (for example, conditions where the temperature fluctuates above and below the dew point) presents a challenge. To address this limitation, a special-design cooled corrosion probe has been developed, commercialized and integrated into the distributed control system in the plants. In addition to high-accuracy measurement of corrosion rates, the probe allows for monitoring of pitting corrosion. The most innovative feature of the probe is the cooling circuit, which brings the temperature of the sensors below the dew point, forcing precipitation of moisture and thus permitting corrosion measurements. Additionally, the probe was found to be well-suited for monitoring corrosion in crude distillation unit (CDU) overhead space, where condensation of hydrochloric acid may take place at relatively high temperatures, which would require relatively moderate amount of cooling to be imparted to the probe sensors. This paper presents laboratory-based data from a test simulating CDU refinery environment. A case study is presented to demonstrate how the cooling probe can be effectively used in the plants for corrosion monitoring.INTRODUCTIONConventional corrosion-monitoring techniques such as weight-loss coupons to assess corrosion damage are commonly used in plants1. However, the use of coupons is not only labor-intensive, but also does not deliver real-time corrosion data, thus effectively serving as a “backwards-looking” monitoring tool. Linear polarization resistance (LPR) probes have the advantage of providing the operator with accurate, real-time corrosion rate data; however, the probes can only be deployed in conditions where the measured environment possesses certain minimal conductivity."

Jan 1, 2012

By W. G. Davenport

Methods of extracting copper are evaluated in terms of innovations during the 1970's, and predictions to the end of this century are made. It is concluded that between one and two new smelters and refineries will be needed per year until the turn of the century, and that most of these smelters will be of the oxygen or oxygen-enriched flash furnace type. For converting, the Peirce-Smith converter will still predominate, but the Hoboken converter will play an increasingly important role. Five Japanese pollution control systems are described and it is suggested that much of this technology will be included in future smelting installations. Further growth of hydrometallurgy is predicted, especially for oxide ores, based on improved product metal quality and low plant cost. A n increased level of scrap resmelting is also expected.

Jan 1, 1980

By K. R. Barnard, K. D. Marte, T. V. Gamarano

"The first commercial scale application of CSIRO’s direct solvent extraction (DSX) technology has been in operation at the Boleo project in Mexico since December, 2015. In this application, DSX is a synergistic solvent extraction system consisting of the extractants LIX 63 and Versatic 10 for recovery of cobalt and zinc from a solution background of manganese, magnesium, and calcium. Key operating parameters such as metal extraction, phase disengagement and extractant stability are summarized and discussed in this paper.INTRODUCTION Commissioning of the Boleo processing plant, located on Mexico’s Baja peninsula, began with the copper circuit starting in late 2014, with first copper cathode production achieved in January, 2015. The cobalt and zinc circuits began commissioning in December, 2015 with first zinc sulphate monohydrate (ZSM) and cobalt cathode production achieved in February and April, 2016 respectively. The Boleo project flow sheet and development has been described in detail in previous publications (Dreisinger, et al. 2005; Dreisinger, Baxter, & Molnar, 2006; Dreisinger, et al. 2008; Dreisinger, et al. 2009) and is summarized schematically in Figure 1. Boleo is a mixed oxide/sulphide Cu-Co-Zn-Mn high clay deposit that is processed in a whole ore, atmospheric, oxidative and reductive, sulphuric acid/seawater leach. Copper is recovered as cathode by conventional solvent extraction and electrowinning. Cobalt and zinc are recovered, from a solution background of manganese, magnesium, and calcium, by CSIRO’s synergistic solvent extraction technology Direct Solvent Extraction (DSX). Cobalt and zinc are bulk stripped from the DSX circuit and then further purified by phosphinic acid solvent extraction to produce zinc sulphate monohydrate granules via spray dried granulation and cobalt cathode rounds via divided cell electrowinning."

Jan 1, 2017

By T. Avilez, D. Salari

"The economics of developing gold deposits containing elevated levels of cyanide soluble base metals is often challenged by high cyanide consumption and increased operating costs. SART is a chemical process that enables cyanide consumed by base metals to be recovered and recycled for gold leaching. The process also provides concurrent recovery of the base metal to generate incremental revenue from the sale of high-grade base metal sulphide concentrates. Although SART was developed and successfully piloted by Lakefield Research and Teck Corporation in the late 90’s and is now a public domain technology, the adoption of SART has been relatively slow due to concerns about implementation costs and the reliability of metallurgical performance. Through extensive experience in selective metal sulphide precipitation applied to mining wastewater since 2007, BQE Water has provided process know-how, design along with operations and maintenance experience to a number of projects involving the integration of SART into various metallurgical flowsheets on an industrial scale. This paper presents the commissioning experience and operating data from a SART plant treating up to 500 m3/hr of leach solution at a heap leach operation in Mexico. INTRODUCTION One of the current trends in the gold industry globally is the increasing importance of complex polymetallic gold deposits as discoveries of large Carlin type gold deposits become increasingly rare (Sceresini, 2005). The presence of cyanide soluble copper and zinc in complex gold deposits necessitates changes to the traditional gold extraction metallurgical flowsheet. A tool available to the industry to help manage the interference of cyanide-soluble base metals in gold extraction is the SART (sulphidization-acidification-recycling-thickening) process. SART breaks the weak acid dissociable (WAD) base metal-cyanide complexes, precipitates the metals as high-grade sulphide concentrates and makes the freed cyanide available for recycle."

Jan 1, 2018

By J. H. Pee, Y. J. Kim, H. U. Lee, G. H. Kim

The general recycling process of tungsten scrap to produce tungsten raw materials (tungstic acid, ammonium paratungstate (APT) and WO3) have been carried out by the oxidation, milling, sodium-fusion, dissolution, and extraction processes. Many studies on the high temperature oxidation of tungsten scrap have investigated various aspects such as swelling kinetics, fracture resistance, and the effect of alloying composition. However, the accelerating factors on the scrap oxidation rate during oxidation were not considered here. In general, oxidized products were fused with sodium carbonate or sodium hydroxide to produce Na2WO4. Later in the process, solid Na2WO4 was dissolved in water. This process required considerable reaction time and was a costly process. Therefore, the aim of this study was to increase the solubility of solid oxidized products to produce Na2WO4 solution by hydrothermal reflux method. Na2WO4 solution was used to produce CaWO4 and H2WO4 by general chemical reactions with calcium chloride and hydrochloric acid. Ammonia solution was also added to the tungstic acid to produce APT. In this study, the effect of ammonia addition on the APT precipitation process was investigated in detail.

Jan 1, 2015

By D. H. Ryan, B. Abdul, M. Pernechele, E. Asselin

Hydrometallurgical processing of sulphide concentrates at medium temperature (150°C) produces residues, which contain valuable metals (Cu, Ni) as well as sulphur and iron bearing minerals and phases. The low solubility of iron during the medium temperature processing of sulphide ores can favour the formation of poorly crystalline, nano-scale iron oxide/oxyhydroxide phases. A better understanding of the formation and structure of these iron precipitates may elucidate key factors that would ultimately result in lower valuable metal losses and more stable leach residues. Residues from two medium temperature leach processes were characterized by Mössbauer Spectroscopy. Some portions of the Mössbauer Spectrum were suspected to be linked to jarosite but could not be positively identified as such. There was a broad range of disorder and substitution present in the material and solely attributing it to jarosite proved difficult. Various synthetic jarosites with Cu substitution were precipitated for Mössbauer analysis. These were then characterized by Quantitative X-Ray Diffraction (QXRD), Scanning Electron Microscopy (SEM), Inductively Coupled Plasma Mass Spectroscopy (ICP-MS) and Mössbauer Spectroscopy. The Mössbauer Spectra of the synthetic jarosites is compared with that of the residues from medium temperature (150°C) sulphide concentrate leaching.

Jan 1, 2014

By Loui Geoffroy, Philippe Gaultier, Martin Piotte, Claude Coache, André Drouin

"Automatic driving at high speed of an underground truck was tested at Brunswick mine in September 1995. Modifications to the truck included: a remote interface to control actuators, front and back video cameras to follow a roof mounted optical guide and proportional hydraulic controls on the steering.The mathematical model of the hydraulic system was adjusted using least square regression. The steering data, used in calculating the regression parameters, were acquired from the moving truck. The automatic steering control used three measured variables: lateral deviation, angular deviation and steering angle. Lateral deviations are obtained using the cameras, which are in continuous view of the guide, while steering angles are acquired from an extensiometer placed at the articulation point of the vehicle. Gain scheduling was used to compensate for vehicle speed and available hydraulic flow. Non-linear characteristics of the modeled hydraulic system were offset using open loop compensation.Speeds up to 23 km/h in forward direction and 13 km/h in reverse were achieved deviaduring continuous testing along one of the mine’s production drifts. Proportional steering was essential in achieving high speeds, as it enabled more precise positioning of the vehicle’s steering direction while reducing the abuses on cylinder and cylinder pins via diminished oscillations about the optical guide at high speeds."

Jan 1, 1997