Search Documents

By T. Donkin, B. Patterson, M. I. Guthrie, J. T. Ross

"The interest in the use of sensor-based particle ore sorting has increased significantly with the recent advances in the sorting technologies and higher capacities per unit. This technology has the potential to provide great value in processing lower grade ores from the mine whilst delivering higher grades to the mill as well as in upgrading waste rock into ore. Typically, the focus is on the amenability of the ore to ore-sorting and associated reductions in the consumption of energy, water and consumables. However, layout has a significant impact on the installed cost of a concentrator and the layout impacts from fitting an ore-sorting circuit into the concentrator plan need to be carefully considered. This paper examines layout considerations that play an important role in ore sorting projects. These include additional crushing and screening requirement, transportation of the rejected material back to the waste stockpile (mine fleet requirements) and effects on concentrator footprints.INRODUCTION Ore sorting has been practiced throughout history with an early report by Agricola in 1556. Metallic and non-metallic minerals were extracted from rocks by laboriously breaking them with hammers and picks and hand-picking selected material with higher grade off a table. The concept has not changed but the sorting technology has evolved significantly over the last 20 years. Ore sorting is usually a dry process in which a portion of the material is rejected based on mineral properties and/or grade. The methods used for sensing ore particles cover a large range of physical properties. A variety of sensors are available that differ on the discrimination technique that is used, which include: photometry, radiometry, conductivity, magnetism, microwave, X-ray transparency: X-ray transparency and luminescence and UV fluorescence (Sivamohan and Forssberg, 1991; Wotruba, 2006). There are two main ore sorting techniques: particle ore sorting and bulk ore sorting. According to Nadolski et al (2018), the potential for sorting is determined though analysis of grade heterogeneity within the orebody (greater heterogeneity represents more opportunity to add value to a project) at the scale of the intended sorting unit size."

Jan 1, 2019

By C. Hari Manoj Simha, J. Gholipour, M. J. Worswick

Due to the high pressures involved in the hydroforming process, friction and lubrication play an important role and can affect formability of the material. Tubes of A1Mg3.5Mn aluminum alloy, of 76.2 mm (3 inch) outside diameter and 2-mm thickness were considered in this study. Three kinds of lubricants, Al070, Hydrodraw711 and water, were applied to the tubes and tubes were hydroformed to burst in a square shape die cavity. The key process parameters were recorded during the tests. An in-house Gurson-Tvergaard-Needleman (GTN) damage-based material model, implemented in LS-DYNA, was used to model the process and predict the formability of this material. The applied axial loads and internal pressures recorded during the tests were used in the computations. The effect of different types of elements (solid and shell) with different constitutive models (von Mises and GTN models) in predicting the strain distribution is studied. The GTN damage-based material showed a good ability to capture necking and displacement histories in this process. Both predicted and measured results showed that the lubricant with lower coefficient of friction can effectively increase the comer expansion.

Jan 1, 2006

By Adam Turcotte

Mining operations consume a considerable amount of energy, and while reduced energy consumption is desirable, it is not always clear how to achieve this goal. Understanding the opportunities to optimize energy consumption is crucial, and the key to understanding is visualization. One option is the Sankey diagram, which has been used for over 100 years to visualize the flow of energy, materials, or cost through various processes. However, there are drawbacks to this approach that must be addressed. In a Sankey diagram, each flow is represented by an arrow possessing a width proportional to the magnitude of the flow it represents. The diagrams show input flows, how energy is converted and into what form, and also output flows. As per the first law of thermodynamics, the total energy output is equivalent to the total energy input, so any energy that is not transferred to another process is considered to be wasted. These waste flows are depicted in Sankey diagrams and make it straightforward to associate energy sources, sinks and waste flows. Unfortunately, Sankey diagrams do not convey all information required to support practical decision making for redirecting individual energy flows. Based only on a Sankey diagram, it may become evident that a significant flow of waste heat is of the appropriate grade (temperature) and volume to meet an on-site heat demand currently being met with paid-for, possibly carbon intensive fuel. However without augmenting the Sankey diagram with 3D spatial, true geometric analysis, the practicalities of the concept or idea may not be fully appreciated. Another issue with a Sankey diagram is that the magnitude of the energy flowing between processes may have temporal fluctuation or variability on different timescales (diurnal, seasonal, interannual). Currently, Sankey diagrams only provide a static picture of energy conversion and consumption, so that, for example, 4 separate diagrams could have to be prepared for each season. A new energy flow visualization technique which we have called Sankey Trees has been developed. Process locations are defined within a 3D model of the site being studied, and the magnitude of the flow between each pair of processes considered is replaced with a time series. Branches of sustained and diminishing flows are represented through variation of the geometric properties of the branches of the trees. These branches are animated to indicate the direction of flow, and branch joints are used to indicate that a process is transporting one form of energy to multiple processes.

Aug 1, 2013

By R. W. Lawrence

Sulphide is an effective reagent in the precipitation of base metals for both metal winning and environmental control. BioteQ Environmental Technologies Inc. has successfully demonstrated in industrial plants that biogenic sulphide reagent can be generated cost effectively and used to win metals such as copper, zinc and nickel from low-grade leach solutions and wastewater. Commercial plants in which sulphide reagent is used to produce high quality treated effluents for discharge directly to the environment are also in operation. Operations utilizing biogenic sulphide reagent for copper recovery from acid drainage and low grade leach solutions are discussed, including those at Bisbee, Arizona, commissioned in 2004 and at the Dexing mine in China, scheduled for commissioning in 2007. In addition, a new application of BioteQ's technology for the recovery of copper from gold-cyanide solutions, and the regeneration of cyanide, utilizing biogenic sulphide in place of chemical sulphide reagents in the SART process is described.

Jan 1, 2007

By R. R. Culbert

Several thousand parts per billion of uranium are present in some alkaline lake and ground waters of the Okanagan region, British Columbia. To a major extent the uranium content of these highly anomalous waters is controlled by their levels of dissolved bicarbonate. In lakes, dissolved bicarbonate and the organic content of the sediment largely control the partitioning of uranium between sediment and water. This relationship is found to a lesser extent in alkaline creeks, and transported geochemical anomalies in soils appear where uranium-bearing alkaline ground waters have encountered organic materials. There is a possibility that young, near-surface deposits (with very low radioactivity) are forming from these uraniferous waters.

Jan 1, 1978

By R. F. Favreau, R. A. Morin, G. W. Kuzyk, P. J. Babulic, N. J. Tienkamp

"Atomic Energy of Canada Limited is constructing an Underground Research Laboratory (URL) as part of a comprehensive program to evaluate the concept of nuclear fuel waste disposal deep in crystalline rock formations. Careful blasting methods have been used to minimize damage to the excavation surfaces. Good wall quality is desirable in any excavation. In excavations required for nuclear waste disposal, the objective will be to minimize blast-induced fractures which may complicate the sealing requirements necessary to control subsequent movement of groundwater around a sealed disposal vault. The construction of the URL has provided an opportunity for the development of controlled blasting methods, especially for drilling accuracy and optimization of explosive loads in the perimeter and cushion holes. The work has been assisted by the use of blast simulations with the mathematical model Blaspa.This paper reviews the results of a recent project to develop a controlled method of full-face blasting, and compares the observed field results with the results of a blast simulator called Blaspa. Good agreement is found between the two, and the Blaspa results indicate quantitatively how the blasting may induce damage in the final excavation surface. In particular, the rock in the final wall may be stressed more severely by the cushion holes than by the perimeter holes. Bootleg of the rock between the perimeter and cushion rows occurs when the burst out velocity imparted to it by the explosive loads in the perimeter holes is inadequate. In practice, these findings indicate that quantitative rock stress and rock burst-out velocity criteria can be established to minimize wall damage and bootleg. Thus, blast simulations become an efficient way to design controlled blasting and to optimize quality of the excavation surf ace."

Jan 1, 1989

By L. Freitag

"The Dollard oil field in southwestern Saskatchewan is a stratigraphic trap of irregular shaped perimeter. The reservoir is a low-angle monoclinal structure with a dip of approximately 100 feet in 5 miles from west to east across the long axis of the reservoir. Production of. 23° API gravity crude is obtained from a Jurassic sand referred to as the J-2-A, at an approximate depth of 4,500 feet. Reservoir studies and fluid analyses revealed that the crude is highly undersaturated, having a solution GOR of approximately 130 cubic feet of gas per barrel, that the reservoir has no definable water table, and that it appears to be of a closed-boundary type. Oil production was marked by a rapid pressure decline and it was soon evident that the greatest ultimate recovery would be best obtained if the natural driving energy of the reservoir were augmented by some artificial energy source. In support of a pressure maintenance programme, studies were conducted on flood-pot recoveries of large-diameter cores, and a potentiometric model study of the field was made. These studies indicated that a successful water flood would be obtained. The Dollard field was unitized in 1955 and pressure maintenance started in March 1956."

Jan 1, 1959

By Robert Walker

Agenda ? Investment thesis ? Engagement ? Competitive advantages Corporate engagement ?The ESG Services team carries out engagement activity with the companies in the Ethical Funds portfolio on behalf of investors ?Each year about 50 companies (20% of our assets) are placed on our Focus List based on assessment of significance and severity of ESG risks and the extent of our portfolio exposure ?We engage in direct discussions on material ESG issues ranging from climate change to human rights to executive compensation ?This enables the team to gain insight into how management is addressing various risks to the business and encourage positive change where gaps exist

Aug 1, 2013

By Robert B. Parsons

"It is easy to throw darts at government - and government often deserves to be a target. This month, Tax Notes examines tax legislation from a different angle, and sees some bright spots.The following article is based on a paper presented by the author at the International Gold Symposium in Rio de Janeiro in August 1989Introduction""No man's life, liberty, or property are safe while the Legislature is in session.”With one federal government, ten provincial governments, and two territorial governments all claiming to have constitutional rights to tax and otherwise regulate Canada's mining industry, and with each of these thirteen governments pursuing their respective rights with some vigor, government involvement in one way or another is an accepted way of life in the industry. While one's initial reaction to government involvement in an industry might be one of scepticism or fear, generally speaking the federal, provincial, and territorial governments in Canada tend to be pro-mining. They recognize the importance of the mining industry to Canada, especially in terms of job creation and exports. It is not surprising, then, to find that an array of valuable fiscal incentives are available to the industry through federal and provincial legislation.This paper summarizes the principal incentives that are inherent in Canada's tax legislation, as well as the Canadian Exploration Incentive Program. Although it is beyond the scope of this paper to deal with all of the incentives that are available, it is noted that various forms of federal or provincial assistance are also available outside of specific legislation, through negotiation with government departments. This latter type of assistance is generally directed toward helping with the cost of infrastructure such as roads or hydro lines, or Jess often toward loan guarantees or similar financing assistance."

Jan 1, 1990

By William Petruk

Mineralogical investigations in connection with gold metallurgy are usually performed to find the reason for poor recoveries by cyanidation or by other leaching techniques. Poor recoveries most commonly are obtained when (I) native gold is encapsulated in an insoluble mineral as "invisible gold"; (2) native gold is coated with a precipitate; (3) gold-bearing products are insoluble in cyanide solutions; (4) carbonaceous material in the ore adsorbs gold; and (5) associated minerals decompose and consume cyanide. Samples of refractory material quite often have low gold tenors. It is difficult to find the gold-bearing minerals in such samples with an optical microscope because the probability of finding trace minerals in samples is small. The probability decreases with decreasing grain size of the gold-bearing mineral and with decreas¬ing gold tenor of the sample. Techniques have been developed to increase the success rate of finding gold grains; some are (1) concentrating heavy minerals; (2) preparing special polished sections; (3) searching with an image analyzer; and (4) dissolving associate silicate and sulphide minerals.

Jan 1, 1989

By D. H. Wilson

"This paper examines the increasing need for mechanical-electrical people within the industry and some of the reasons why such a shortfall exists. It is suggested that, in part, it is image related. The present industry-education relationship in addressing the situation is examined and some thoughts are expressed on how these may be built on, in order to help solve the problem of attracting people to this critical area.IntroductionAs a long-time proponent of plant engineering and maintenance as a management function, I would like to review the progress made by the industry/ educational approaches in satisfying the needs in that area. In doing so, I would like to make the following points:1) that there has been an accelerating shortfall of mechanical-electrical people relative to the needs of the industry;2) that the condition will probably get worse before it gets better; ,3) that the past industry I educational approaches to alleviate the problem have met with limited success; and finally4) I would like to review some of the things being done and consider how these efforts might be extended."

Jan 1, 1981

By G. E. Norman, R. E. Michelutti

"One of the major objectives of Falconbridge has been and continues to be, to minimize the impact of its operations on the environment around its Sudbury operations.The approach to achieving this objective and the results, are discussed under the following topics .I . Sulphur Dioxide Emission Improvements.2. Effluent Treatment Improvements .3. Effect of the Envrionmental Improvements.Sulphur Dioxide Emission ImprovementsHistoryThe rejection of pyrrhotite in the concentrators is one method of reducing the amount of sulphur to the smelter and therefore the sulphur dioxide emissions. In the 1950s and 1960s, Falconbridge developed the capability to remove 54% of this pyrrhotite. Numerous attempts were made to increase this amount by treating the pyrrhotite for recovery of nickel and in some cases elemental sulphur. Processes tested and operated were: hydrometallurgical pilot plant, roast-leach commercial operation and nickel-iron refinery. None of these processes proved to be commerically successful for both technical and economic reasons. Falconbridge therefore redirected its efforts to reducing sulphur emissions by improving its smelting process under The Smelter Environmental Improvement Project. A major component of this project was the installation of a sulphuric acid plant to recover the S02 in the roaster off-gases."

Jan 1, 1984

By Niels Verbaan, Ron Molnar, David Dreisinger

"An acidic chloride leach solution was generated from the treatment of an ore containing the following value elements: silver, gold, indium, gallium, copper, zinc and lead. Iron was also co-extracted into solution as a ferric chloride species. Iron extraction was a significant component of the overall acid consumption of the leaching process. The recovery of iron by solvent extraction and water stripping was investigated. Tri-butyl-phosphate (TBP) was very effective at recovering iron from the leachate. The water strip solution could be decomposed to produce ferric oxide (hematite) and hydrochloric acid for recycle via hydrothermal hydrolysis or pyrohydrolysis.INTRODUCTION The Malku Khota deposit is situated in the eastern part of the Bolivian Altiplano at elevations between approximately 3,800 and 4,580 meters above sea level (Figure 1). The project is located 98 km east-southeast of Oruro, and 85 km south of Cochabamba in a relatively remote area."

Jan 1, 2016

By M. R. Henzinger, G. Lenz, A. Gaich, Pötsch, W. Schubert, P. Wagner

"The better the information on the rock mass and its fracture system, the better is the basis for any rock mechanical decision that is required during the excavation process. While in conventional tunnelling free view to the tunnel face is available, possibilities are limited for mechanised tunnelling using a tunnel boring machine (TBM). An approach, already formulated in 2005, is used that produces digital photographs through openings in the cutting wheel of a TBM and merges them into a circular three-dimensional image. The 3D image is then used for geometric rock mass characterisation purposes including geological mapping, for example to measure spatial orientations or determine joint spacing. In the paper the basic concept is described together with first results from a pilot test.INTRODUCTIONA three-dimensional image unites digital photographs with spatial information on the objects/surfaces it shows. Since they combine geometric and visual information they are a straightforward source for geometric rock mass analysis and geological mapping. Their obvious benefits among others are: (i) they allow spatial measurements even in inaccessible regions, (ii) they provide objective and reproducible records of the rock mass conditions, and (iii) they increase working safety (Gaich et al. 2004).Pre-requisite for the generation of 3D images is the acquisition of at least two photographs from the region of interest. From the photographs the imaged object surfaces are reconstructed by means of image analysis using methods from photogrammetry (Slama, 1980) and computer vision (Hartley & Zisserman, 2001). See also Figure 1."

Jan 1, 2015

By Hammenm R., J. Hammen, C. Hammen

"The production of salable Rare Earth Element (REE) products necessitates a sequence of chemical separation steps between the mine and market commodities. The effectiveness of the chemical separations that purify REE salts is critical to the success of the producer, as the purity of REE salt products affects their market price. This is due to the fact that impurities in REE salts, even at low levels, can be deleterious to the function and usability of the end product. The purification of REE by removal of low levels of contaminant has been referred to as "product polishing". The technologies commonly in use for product polishing, solvent extraction (SX) and ion exchange (IEX) are challenged by the availability of separation chemistries to separate the contaminant from the desired REE salt. In simple terms, if a product specification is 99.9% purity, the SX or IEX separation reagents need to have at least a 999:1 selectivity ratio. Significant testing has been carried out on the use of solid phase extraction (SPE) columns to extract low-level impurities such as aluminum or zinc from REE product streams. The SPE columns are nano-composite materials that have rapid equilibration kinetics with the solutes being processed by the columns. The SPE matrices have been modified with chelating ion exchange ligands that bind the contaminating ion with great selectivity in residence times of a few seconds. Thus, REE streams with 1 to 2% of contaminating aluminum ions, have been polished to >99.99% purity. In this paper, results are presented on the removal of aluminum impurity from a didymium (neodymium+praseodymium) product stream using SPE technology. The selection of the SPE medium and the process steps to treat the feed solution for aluminum removal and ultimate stripping and recycle of the solid phase extractant are discussed."

Jan 1, 2014

By S. Simukanga, J. Masinja, P. A. Bepswa, A. N. Mwale

Screening is an important operation in dry and wet closed circuit mineral processing applications. Most of the operations have seen the benefits of using fine wet screens in primary grinding sections where the product is relatively coarse, and screens can handle the tonnage. Although many models are available, most of them are confined to dry and wet coarse screening applications. Most models do not give good predictions for wet fine screening. To facilitate model development, pilot plant tests were performed using a single deck Derrick Screen at aperture sizes of 45µm, 75µm, 106µm, and 150µm. Experimental data for a range of feed solids concentrations and flowrates was collected and used to calibrate the performance of the screen under the different operating conditions. The results showed that the performance of the screen deteriorated with an increase in feed solids concentration, and, similarly with an increasing feed flow rate. The percentage of fines carryover also increased with the reduction aperture size. The carryover was even more pronounced at higher feed rates and solids concentrations. A model was developed for predicting the performance of fine wet screening. Data from the test work was used to compare the actual and predicted results, and to calibrate the model. Additional independent data was used to validate the model and assess its limitations. This model will give an expected screen performance based on the initial feed conditions. It incorporates screen design parameters that allow for an estimation of a suitable screen size for a desired performance based on given feed conditions. This paper discusses; the results from the test work performed, the model development and its limitations.

Jan 1, 2016

"Discrete Fracture Network (DFN) modelling has increasingly being used in many geotechnical and mining engineering problems, the authors believe there is an ever greater demand to provide updated guidelines that address the collection of discontinuity data in the specific context of DFN models. In general terms, the generation of a DFN model requires collecting information on i) fracture orientation, ii) fracture intensity, iii) fracture length and iv) fracture terminations. The International Society of Rock Mechanics (ISRM) suggested methods for the quantitative description of discontinuities in rock masses directly include most of these parameters. However, there are important differences engineers should be aware. To what extent discontinuities can be sampled and which limitations are inherently introduced in the analysis by the sampling methods being adopted represent important aspects that should drive the collection of discontinuity data for DFN analysis; this will require the introduction of a more appropriate set of guidelines bridging the gap between the current, very practical, ISRM methods and the data requirements imposed by the use of new DFN technologies.INTRODUCTIONThe last decade has seen a major increase in use of the Discrete Fracture Network (DFN) approach, both as a stand-alone tool or integrated within more complex geomechanical simulations (Rogers et al., 2014 and Elmo et al., 2014). In particular, the DFN approach offers the opportunity to maximise the use of fracture data collected from mapping of rock exposures and to construct synthetic rock mass (SRM) models. However, the potential of DFN based modelling is limited if there is insufficient care in collecting the necessary structural data at the required engineering scale. DFN models are also subject to the process of data calibration and validation (Hadjigeorgiou, 2012). With DFN modelling becoming an almost integral part of many geotechnical and mining engineering problems, the authors believe there is an ever greater demand to review the process of collecting fracture data in the specific context of DFN modelling.The value of the DFN model depends directly on the quality and quantity of available field data. For example, fracture length (persistence) is an important parameter in DFN modelling; however, this parameter is either seldom available at the pre-feasibility stage due to a lack of exposures (man-made or natural), or engineers have access to limited length data collected along exploratory drifts. Characterisation of rock exposures should also take into account limits of window/scanline mapping techniques with respect to both trace length bias and the effect of cut-off assumptions inherent in the mapping methodology."

Jan 1, 2015

By Tim Gartner

This paper introduces a new application of a proven technology to provide dynamic, voltage regulation in underground mine electrical distribution systems. This technology acts to ?stiffen? the electrical power feeding continuous miners and generally raise and improve the voltage regulation at the continuous mining machines which may be located over long cable distances from the mine incoming electrical substation. This is extremely valuable for large underground continuous mining operations that use high power electrical mining machines fed over very long cable lengths (measured in 10s of km, from mine shaft to mine operating face). This new technology provides fast acting dynamic voltage regulation (voltage support) while starting continuous borers and extensible conveyor belts. Additionally, if the mine suffers from a lower distribution voltage due to long cable lengths, this new technology will raise the overall voltage at the mining machine, which can increased mining machine production and lead to longer motor life. The technology is based on voltage source converters operating as static VAR compensators specially packaged for the harsh underground mine environment. While static VAR compensator technology has been successfully used in utility and large industrial applications for many years (including open pit mining and arc furnaces), it has not (until now) been applied in underground mining. The paper will present the problem of poor voltage regulation in underground mines on weak electrical utility networks. It will then discuss some of the alternatives that have been used to resolve this voltage problem. It will then introduce the new technology used to solve the problem and review the issues involved in using this technology in the harsh underground environment. Finally, the paper will present preliminary performance results from an actual installation in a large underground continuous mining operation in Canada.

May 1, 2003

By Doug Barnstable

"Quinsam Coal Ltd. is assessing the potential of developing a thermal coal deposit near Middle Quinsam Lake on Vancouver Island. The coal reserve outlined is classified as a high-volatile, bituminous ""A” steam coal and is composed off our separate seams of varying quality within the Late Cretaceous Comox Formation.Open-pit mining methods will utilize a walking dragline and a truck / shovel module as the primary stripping tools. Following washing and mechanical drying in a Baum jig preparation plant, the coal will be transported to the proposed dock at Campbell River for shipment via 55, OOO-DWT vessels to world markets. The paper will outline the development and status of the project to date. IntroductionQuinsam Coal Ltd. is a joint venture of Weld wood of Canada Ltd. and Luscar Ltd . The participants propose to develop a thermal coal mine in the Middle Quinsam Lake area, 17 miles inland from Campbell River on Vancouver Island (Fig. I). By acquiring all the assets of Canadian Collieries in 1962, Weldwood also came to own the coal rights of the area proposed for development. Luscar Ltd . ha s been designated as project manager until completion of construction and thereafter will act as operator of the mine.Surface mining methods will be used to produce approximately 1.0 million short tons of coal annually from the Quinsam property. Seven separate mining pit s will be developed along with the supporting minesite facilities, including a proper paration plant. Transportation routing to Campbell River and the establishment of docking facilities will be required. The initial economic life of the mine is 12 years, with the provision to extend this in the future by developing higher-ratio, auger or underground reserves."

Jan 1, 1980

By Robert B. Parsons

"The junior mining company's bank account is depleted, but there are high hopes for the company's property. Where to get the necessary development funds is a common problem facing many juniors.This month, Tax Notes discusses briefly the principal income tax implications of several alternative development plans that are typically available to the junior mining company and its shareholders.IntroductionAt some point in time, many junior exploration companies face a common dilemma-a promising prospect has been proven up and is read y for further development, but alas, the company is flat broke! In this situation, a number of alternatives is available to the company, including the possibility of ""going it alone"" by raising capital through a public offering, or by striking a deal with a ""major"" or some other substantial investor.This article focuses on the latter possibility, and discusses in broad term s the main income tax implications of various arrangements between a typical junior exploration company and a larger public company for the development of a particular property. It will be appreciated that a discussion of other important considerations, such as those pertaining to securities exchange regulation s and company law requirements, is beyond the scope of this article.Jointly Owned CorporationPerhaps the simplest way of dealing with the problem of financing the development of a property is to sell the property outright, pocket the proceeds, and run! Clearly, though, this alternative is unacceptable to most prospectors and developers, who are predictably reluctant to completely relinquish their equity interest in a promising property. An additional strike against such an outright sale is that the sale could trigger an income tax liability. Generally speaking, in the case of a simple sale of a mineral property, for income tax purposes the proceeds are applied to reduce the taxpayer' s unclaimed balance of Canadian development expense (""CDE""), with any unapplied excess being brought into income and taxed at ordinary corporate tax rates."

Jan 1, 1983