Search Documents

By T. R. Stanley

Introduction The purpose of this paper is to interest mining men in the economic possibilities of sand deposits suitable for modern foundry work. Many members of the profession are constantly travelling over the country and it is felt that some knowledge of the necessary properties of foundry sands will enable these men t0 recognize such deposits. It is the experience of the writer that good sands suitable for the varied work of a foundry, such as that of the Consolidated Mining and Smelting Company, at Trail, are almost impossible to obtain from western Canadian sources. It is hoped that the following discussion may arouse some interest in the search for such sands. Sands are used in foundries for two purposes. The main use is for making moulds suitable for receiving hot metal. The mould must retain the? required shape until the metal has solidified. The second use of sand in the foundry is as an abrasive in sand blasting. This is a relatively minor use, and consequently will not be dealt with in detail. Any coarse sand with a high content of quartz will serve this purpose, but round-grained sands are superior to angular types, because they have not the same tendency to shatter on impact with the casting. Sand plays an extremely important part in the successful production of sound castings. This is more evident today than ever before, due to the greater variety of castings and alloys, each of which requires special sand characteristics. Poor sand is responsible for a great many foundry troubles which formerly were attributed to bad? metal; in fact, one investigator goes so far as to say that ninety per cent of bad castings can be traced directly to the sand. Very little of the vast amount of sand distributed over the earth's surface is suitable for moulding. It is the purpose of this paper to describe briefly the properties which are essential in good moulding sand. Sand for this work must be able to withstand the wash and hydrostatic pressure of molten metal, and yet be sufficiently porous to allow the gases generated in the mould to escape.

Jan 1, 1935

By G. T. Lapidus, O. J. Solis-Marcial

Currently, ores with high-grades of copper oxides and secondary sulfides have become increasingly scarce, which has encouraged industry to look for alternative raw materials to obtain copper. The problem is that primary sulfides are difficult to dissolve at near ambient conditions. Proposed hydrometallurgical processes have not been implemented beyond a pilot or demonstration scale. One of the principal disadvantages is that the majority of these processes are not viable with ores that contain less than 4% copper. One of the more recently proposed techniques involves the use of organic solvents in the dissolution of copper concentrates with a chalcopyrite content of between 20 and 30%, which has shown high efficiency. The present research explores the ability of this process to leach copper from low grade chalcopyritic ores (<4% Cu) at different temperatures ranging from 20 to 50°C. It was found that depending on the temperature, high percentages of copper were extracted in 40 to 100 minutes, using different oxidants. Additionally, distinct leaching behavior was observed with each oxidizing agent. In some cases, the extraction kinetics adjusted to the diffusion controlled shrinking core model.

Jan 1, 2014

By G. E. Rowan

"DURING the dark ages, the cherished dream of chemists was to find a process for converting base metal into gold. Many a wealthy-but-gullible patron lost a fortune in the search. Men who work with metals today are a bit more realistic. I haven't heard of a metallurgist who expects to develop any one alloy that will resist all corrosive media. In the field of stain-less steels, there are about forty different types of alloys that are used where corrosion is a •problem.A stainless product is ordinarily selected because it offers one or more of the following qualities:(1) Resistance to corrosion (2) Resistance to oxidation at high temperatures (3) Good mechanical properties at room temperature (4) Good mechanical properties at high or low temperature (5) Attractive appearance (6) Ease of maintenanceToday we are interested in discussing the stainless steel family of alloys because of their .ability to resist corrosion. We• will not try to explain the Theory of Corrosion. Let us assume that, when surface potential and oxide formations are properly controlled, iron will resist attack in various chemi.cal solutions. The addition of alloying elements to iron does this for stainless steels. The principal stainless alloys used by various Canadian industries are listed in the accompanying Table."

Jan 1, 1959

By N. R. Paterson

"More than a dozen AEM systems are currently being used in the routine exploration for massive sulphides. The systems differ from one another in minor respects, but fall into four main categories: rigid-coupled in-phase/quadrature systems; towed-bird, single-component systems; differential systems; and passive systems.Although field tests are important in demonstrating the performance characteristics of the AEM/airframe assembly (noise-levels, coupling effects, etc.), more meaningful evaluations can be made through physical or computer modelling. The latter approach has been used to compare the response of twelve AEM systems to both vertical and horizontal sheets, simulating a large orebody and a con-ductive overburden respectively. The effects of height changes are also studied.The results demonstrate that each AEM system has its own particular advantages and disadvantages. The relative importance of these is a matter for the geophysicist to judge, on the basis of specific geological and environ-mental information. Data currently available on AEM systems are adequate to permit an objective evaluation of the systems for a particular exploration program."

Jan 1, 1971

By H. W. Wevers

This paper is the result of an intensive literature search and practical study of the problems experienced by a mining company with the frame cracking of their large-tonnage haulage trucks. It explains the advantages of particular HSLA steels for applications in the welded structures of such equipment. Examples of existing welds in truck frames are analyzed. Modern fatigue models and linear elastic fracture mechanics techniques are explained.

Jan 1, 1978

By Frederick J. Browne

Water, water everywhere, but not a drop (fit) to drink! Trite, but how often only too true? What is there met with in mining which, under various circumstances, may be said to be the most sought-for and highly-prized and also the most objectionable and most feared? Water! What visions that combination of five letters brings to all thoughtful minds? Up to near the end of the eighteenth century water was thought lo be an element but was then discovered to be the result of the combustion of two volumes of hydrogen with one volume of oxygen, and water so produced is chemically pure. Pure water is a clear and colourless liquid when seen under ordinary conditions, but appears bluish when seen through a long tube, and this same bluish tint may be observed in many lakes, especially those of glacial origin. A story often told describes a prospector in the desert who, failing to find water to replenish his canteen, suffers torture and death under fearful circumstances. Then again we may recall the flooding of mines, where water poured in so quickly that there was no opportunity of saving the unfortunate workmen. Instances might be multiplied without number showing that either the lack or excess of this essential fluid has taken heavy toll of human life. In all branches of mining and associated industries water must be dealt with to a larger extent, from an economic point of view, than any other substance, and very often the purity of the water is a matter of considerable importance.

Jan 1, 1925

By A. Bauer

This paper describes the trends in recent years in explosives formulated to produce larger blast-hole spacings and over-all lower drilling and blasting costs in hard formations. A consideration of current rotary drilling costs per ft of hole and per ton of muck versus hole diameter indicates that it is now possible that we shall see much further use of lower-energy-content, lower-cost slurries and dry mixes, and larger-diameter and, in many instances, cheaper blast holes. These will be drilled on current or slightly larger blast patterns to yield the same energy input per ton of rock and similar fragmentation at lower costs.

Jan 1, 1968

By F. Y. Grepe

"THE MOST common type of mine hoist is, as is very well known, that in which the a.c. wound rotor motor is the driving medium. The reasons for the use of the wound rotor motor are, of course, economic. This type of equipment has, during the years, proved to be very reliable and reasonably satisfactory. It is, in fact, still being installed and in some places where a very hard and exacting duty cycle is demanded. As an example, a 600 h.p. 2,300-volt job was recently installed at the Caledonia mine (1) at Glace Bay. This is a vertical. hoist in a shaft only 175 feet deep but it is, nevertheless, working hard bringing coal to the surface and in making a trip at a speed somewhat better than every 20 seconds.The control equipment for such installations usually consists of a pair of primary reversing contactors which are interlocked both mechanically and electrically, together with some form of secondary controller. This, in the case of small hoists, can be a drum controller and metallic resistors or, in the case of larger hoists, a magnetic contactor panel and metallic resistors or, alternatively, can be one of the various forms of liquid rheostats which are available. The liquid rheostats, if of the dipper type, may be manually operated or it may be operated by some form of servo motor mechanism. In the weir type of liquid controller, the electrolite is, of course, pumped in and out of the rheostat."

Jan 1, 1954

By C. S. Chen, Y. J. Luo, M. W. Gao, B. Li, Z. F. Zhang

"To obtain large-sized billets with fine grains and homogeneous elements distribution, uniform direct chill (UDC) casting process, based on annular electromagnetic stirring coupling with intercooling, was employed to produce 7055 alloy billets with a size of F584 mm in this study. The results indicated that there were the coupled effects of annular electromagnetic stirring and intercooling on grain refinement and element homogenization, and also the billets produced by the UDC casting process showed excellent hot workability in comparison to the normal direct chill casting process.INTRODUCTION The high solute 7055 aluminium alloy has a wonderful combination of high specific strength and hardness, good resistance to stress corrosion cracking and high fracture toughness, which is very useful in aerospace application (Yan et al., 2013; Mondal & Mukhopadhyay, 2005). The production of large-sized 7055 alloy billets with high quality is the basic condition for the subsequent application of 7055 alloy to the aircraft. Inhomogeneous microstructures and performances of 7055 billets result from the high alloying element content and the inhomogeneous cooling condition in different regions of billets during the conventional direct chill casting (Paramatmuni et al., 2004; Lalpoor et al., 2011), which will bring bad influence to processing property, functional performance and utilization rate of materials. To alleviate segregation and obtain fine and uniform grains, some effective treatment methods were proposed including electromagnetic stirring (EMS) (Vives, 1989), ultrasonic vibrating (Zhang et al., 2011) and melt conditioning (Fan et al., 2013), on the melt to obtain fine and uniform grains. However, these methods could not effectively decrease the large temperature difference between central and periphery parts of the billet, because the solidification mainly depends on outside cooling including mould cooling and water spraying cooling. To change the heat extraction pattern of the billet functioned solely from the outer surface, based on annular electromagnetic stirring (A-EMS) invented by Xu et al. (2010), Luo et al. (2017) proposed uniform direct chill (UDC) casting coupling A-EMS with intercooling in the direct chill (DC) casting process. An in-mold cooler was inserted to the melt sump, and thus the alloy melt temperature and concentration at solidification front become more uniform."

Jan 1, 2018

By C. Moreland

Fluidized low-temperature carbonization of coal, a recent development, offers a possibility of reducing fuel costs of coal-burning electric ?generating plants. The Research Council of Alberta have built a pilot plant and are conducting a programme to -develop a carbomzation plant for Alberta sub-bituminous coals which will produce char suitable for use as a .boiler fuel, and tar of a potentially high value as a ?chemical raw material. The economies of the process as a whole, and the value of the tar, have yet to be assessed.

Jan 1, 1958

By T. H. Chuang, Y. Y. Shiue

"Rapid whisker growth was significantly alleviated in a Sn-58Bi alloy doped with 0.5 wt.% La. Experimental results showed that many thin, plate-form intermetallic phases appeared in the solder matrix. The absence of tin whiskers was correlated to the shape effect of RE-containing intermetallic plates. After reflowing, Cu6Sn5 intermetallic compounds appeared at the solder/pad interfaces of Sn-58Bi and Sn-58Bi- 0.5La packages with OSP pads, which grow linearly during the aging at 75 and 100? for various times ranging from 100 to 1000 h. In addition, the interfacial intermetallics layers in Sn-58Bi-0.5La solder joints were also observed thinner than those in undoped Sn-58Bi joints. However, RE-containing interfacial intermetallic compounds in Sn-58Bi-0.5La solder joints led to lower bonding strengths in both ball shear tests (0.4 mm/s) and high speed ball shear tests (2000 mm/s). All the reflowed and aged solder joints of both packages were ruptured through the solder balls indicating brittle characteristic INTRODUCTIONIt has been widely reported that solder alloys doped with rare earth (RE) elements reveal many beneficial effects, such as higher strength, lower melting point, improved wettability, and longer creep life (Wu et al., 2004; Ma et al., 2002; Chen et al., 2002). In addition, Dudek et al. reported that the alloying with 0.5 wt.% La in Sn-3.8Ag-0.7Cu solders resulted in an increase of rupture strain, up to 150% over undoped solders (Dudek et al., 2006). However, Chuang and Yen observed that a large amount of long, fiber-shaped tin whiskers were extruded out of the oxidized CeSn3 intermetallic clusters in the matrix of a Sn-3Ag-0.5Cu-0.5Ce solder air-stored at room temperature for several days (Chuang & Yen, 2006). Furthermore, many coarse hillocks appeared around the CeSn3 clusters in the RE-doped alloy after storage in an air furnace at 150? for several minutes. Chuang proposed a mechanism for the phenomenon of rapid whisker growth, which the predominate oxidation of CeSn3 intermetallics in Sn-3Ag-0.5Cu-0.5Ce solders induced compressive stress and extruded the tin atoms out of the specimen in the form of tin whiskers (Chuang, 2007). However, further investigation showed that Sn-9Zn-0.5Ce solders, after long term exposure at room temperature and 150?, were immune to the whisker growth; the immunity was attributed to the refining of the CeSn3 intermetallic phase in the alloy (Chuang & Lin, 2008). The inhibition of tin whiskers through the refining of rare earth containing intermetallics was further observed in Sn-3Ag- 0.5Cu-0.5Ce solders doped with 0.5 wt. Zn (Chuang & Lin, 2009). In addition to the size effect, the thin plate shape of intermetallic compounds was also shown in this study to inhibit the whisker growth on the surface of Sn-58Bi-0.5La solders."

Jan 1, 2012

By J. G. Patterson

"The depressive action of sodium cyanide on chalcocite has been investigated and found to be unstable. Flotation results show that with the addition of sodium cyanide to the system chalcocite is initially depressed but rapidly recovers with time, provided there is sufficient oxygen present.lt is proposed that the unstable depression is due to the reaction of cyanide with adsorbed xanthate and copper ions at the chalcocite surface to form soluble copper complexes. When all the free cyanide has so reacted, xanthate anions can then re-adsorb on the chalcocite surface and the flotation will recover. Results are presented to verify the the above mechanism."

Jan 1, 1968

By M. G. Mena, M. S. Mena-Junio

Silver (Ag) filler is the most attractive choice among all the conductive fillers of die attach materials for the attachment of silicon devices because of its balanced properties and relatively low cost. However, a major problem of silver is that it electrochemically migrates in the presence of moisture and applied bias. In microelectronic devices, silver migration can occur between adjacent conductors/electrodes, which leads to the formation of dendrites and eventually results in short-circuit failure. In order to assess the reliability of these conductive fillers, an investigation for two types of Agfilled die attach materials was done using the water drop test at room temperature and using a 1000 hour temperature-humidity-bias (THB) test under 85 ºC and 85% RH conditions. Four different bias/voltages and six different electrode distance spacing were used. Both dendrite and cloud/lace-like growths were observed as a result of the electrochemical migration of silver, Water drop test results revealed that increasing the applied bias/voltage and decreasing electrode spacing causes migration to occur faster, thus resulting into shorter time to fail (TTF). It was also observed that the growth rate of the dendrites from the cathode increased linearly as the dendrite approached the anode, probably due to a combination of increased ion availability and electric field. A minimum applied bias of 3 volts was required for migration to occur in Epoxy A as compared to 2 volts for Epoxy C. The higher migration voltage requirement for Epoxy A was attributed to the higher volume resistivity of the said epoxy. In addition to the minimum voltage requirement, it was observed that a minimum electric field of about 1 volt/mm is required for migration to occur. The 1000 hour THB testing did not result into any failures. It is surmised that the presence of condensed moisture is another requirement for migration. Such condition is not present during the THB testing.

Jan 1, 2012

By D H. Sharp

The Quebec Cartier Mining Company produces iron concentrate for twelve months of the year from Port Cartier. This J>Ort is designed to handle ship varying in size from 3,000 to 100,000 d.w.t., requiring 50 feet of water at low tide. The harbour was built on shore for reasons of economy and layout, after considering many more conventional offshore designs. It provides for heavy oil bunkering, tanker off-loading, a heavy lift derrick and freight handling, besides ship loading and mooring. The weather for the previous fifty years was studied to enable wind and wave conditions to be accurately assessed for design purposes, and to determine probable lost time due to adverse weather conditions through-out the year. The first ship to be loaded was 60,000 d.w.t.; the second, 20,000 d.w.t. The latter entered the harbour after dark, under its own power, following a tug through the partly dredged narrow entrance. Large ships use tug assistance. Ships may leave the loading berth with the other berths occupied.

Jan 1, 1963

By J-F. Magnan, M-A. Thibault, R. Boulianne, C. Gauthier, J-P. Gagné, G. Dufour

During the production of aluminium in smelters, the anodes used in electrolysis cells have to be replaced frequently. Anode butts are usually placed on anode trays for transportation and cooling, a practice during which Hydrogen Fluoride (HF) is emitted in large quantities. Covers developed in 2000 by Alcoa Deschambault to fit on the anodes trays were implemented, resulting in significant reductions of HF emissions. However, the covers are expensive to maintain and use short-life consumable parts. In January 2004, STAS and Alcoa decided to develop a more efficient design of cover, with lower maintenance costs and no need for consumable materials (like soft cushions). This paper presents a summary of the work performed to develop the new design as well as a summary of the test results.

Jan 1, 2006

"In flotation research, relatively little attention has been paid to understanding particle-bubble detachment phenomena compared with attachment processes. With CFD models now incorporating attachment/detachment kinetics, it is important to obtain more accurate formulations for detachment probability. The formula most often used is due to Bloom and Heindel (2002) who proposed that the rate of detachment would equal the product of detachment frequency, as previously estimated by other authors, and probability of destabilization, as estimated previously by Schulze. These two factors both account for the balance between stabilization and destabilization forces, so the product accounts for this effect twice. An integrated procedure has been followed to estimate the overall detachment rate by re-analysing the process. In this analysis, detachment rate is calculated as the frequency of eddy-aggregate interactions (or “collisions”) sufficiently energetic to cause detachment. The Bond number analysis of Schulze has been incorporated into the turbulence frequency analysis of previous authors in an integrated way. The new formulation has essentially the same type of dependencies as the previous model, but gives a lower detachment frequency. Detachment frequency has been calculated using the new formula for conditions relevant to an industrial flotation cell. INTRODUCTIONIt is well known that the effectiveness of froth flotation for separating different minerals is limited to the particle size range of approximately 10–100 mm (Trahar & Warren, 1976; Trahar, 1981). Fine particles tend to follow fluid streamlines around bubbles limiting the likelihood of bubble–particle collision, while coarse particles can be more easily detached from bubbles before collection can be achieved.Phenomenological models have been developed to quantify the physico-chemical aspects of flotation in order to better understand factors affecting these limitations, and to suggest ways of broadening the window of feasible flotation. Koh and Schwarz (2008) have incorporated these models into computational fluid dynamics (CFD) models of flotation cells, which have then been used for design and scale-up purposes (Schwarz et al., 2015). The models are based on dividing the process of bubble–particle interaction into three subprocesses: collision, adhesion and detachment. Of these, the hydrodynamics of bubble–particle collision and the probability of adhesion have been studied most extensively, while the dynamics of detachment have received relatively little attention from investigators."

Jan 1, 2016

By J. Kramer, T. Hartmann

In the Hydrometallurgical processes, the presence of the so-called “crud” is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design. The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the seriesconnected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation. The transfer of the organic phase into the electrolysis cell can result in a “burnout” of the cathode. The carry-over of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show. To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl®. By this means, we can guarantee our customers the maximum possible solvent recovery and minimise the solvent costs in this process step. This system is presented in detail in this paper.

Jan 1, 2012

By Allan J. Guse

The primary limiting factor for hoisting capacity from great depths is the self-weight of the typical steel wire ropes used for mine hoisting. Steel wire ropes possess properties making them very suitable for mine hoisting including high strength and durability, but have the negative characteristic of being relatively heavy in comparison with their strength. Also, as hoisting depths increase, the service life of steel wire ropes decreases due to the higher stresses and physical effects on the ropes. The significantly higher strength-to-weight ratio of synthetic ropes compared with steel ropes offers the primary advantage of hoisting a larger payload with a similar size rope and hoisting plant. The beneficial properties of synthetic ropes could be used to improve the overall economics of deep underground mining both for new deep shaft projects and for existing mining operations expanding to deeper orebodies. A research and development program has been initiated to evaluate the suitability of a fully synthetic rope for the mine hoisting application, including rope discard methodology and NDT testing. The three phases/projects are: 1) proof of concept with focus on coilability under load (successfully completed in 2012); 2) high speed and load durability optimization & NDT Development; and 3) in-situ mine trial.

May 1, 2013

By C. J. Coulson, G. A. McKay, A. M. Cormie

"The Leitch mine, in the Beardmore area, Thunder Bay district, Ontario, is a part of the Leitch estate. It includes a group of patented claims, staked by P. A. Leitch of Port Arthur early in the century, along bands of jasper, hematite, iron-bearing slates, carbonatized schists, and greywacke, commonly known as 'iron formation'. The folding and shearing in these variably interstratified beds is a striking structural feature. The vein pattern is very definitely related to these structures.ROCKSThe rocks in the area are typical Keewatin lavas-greenstone-overlain by a series of Timiskaming sediments consisting of arkosic greywacke, iron formation, slate, greywacke, conglomerate, and greywacke, in this order from the contact. The sedimentary beds are generally conformable with the older rock contact except on local folds.Small intrusions of diorite occur as nearly vertical dykes and are believed to be of Algoman age. To the northwest of the mine there are larger intrusions of granodiorite belonging to the same period.Several dykes of quartz diabase up to 100 feet in width, striking generally north and south, with a vertical dip, cross the property. These have been classified by W. C. Laird as pre-Keweenawan in age. One of these dykes in particular is of importance for it cuts through the No. 2 vein and serves as a pillar when stoping. It is approximately 6 feet wide.The youngest rock type represented is a sheet of olivine diabase that extends over an area of thousands of square miles in and around lake Nipigon. It underlies most of this area and its outcrops form some of the most interesting topographical features, with fault scarps rising hundreds of feet. In the vicinity of the mine shaft the sheet is about 600 feet thick and extends from a depth of 1,871 feet to approximately 2,470 feet. It has a dense, hard, chilled margin and a sharp, tight contact. It intruded the sediments with very little lateral disturbance. The chief effect was baking, which darkened and hardened the greywacke near the contact. The sheet dips flatly to the cast."

Jan 1, 1954

By Karl J. C. Harries

"The following is an outline or check sheet of some things that might be looked at when considering the concept of a royalty or royalty provisions. It is not intended as a guide to what is right or wrong (that is for the parties to decide). It does not replace the discussions in this work and is not intended to be a complete or exhaustive compilation of matters to be considered. It presumes that you are familiar with the basic concepts of royalties and has been included as an aide memoire only. Use it as such, with caution and common sense, and amend it to suit your needs. Remember also that brevity can result in inaccuracy or imprecision. This is a danger in many points below.The section references are for the sections where the matter is the main subject of the section – see the index for other sections.Royalty TypesNet Proceeds [§§ 5.8.; 11.4.]• No accepted or understood meaning within industry.• Literal meaning, if not defined, would imply “net operating profit”.• Often defined as net profit with revenue base of proceeds from sale of product.• Should not be used without detailed and clear definition. Net Operating Profit [§§ 5.8.; 11.4. – referred to only]• Net profit without recoupment of pre-production expenditures.• Revenue base: usually proceeds from sale of product.• Operating costs deductible.• Some reserves may be permitted.• Recoupment of some post-production capital expenditures may be permitted.• Not often seen as basis for royalties in Canada."

Jan 1, 2003