Search Documents

By Nadarajah Nanthananthan

Mine backfill has been widely used as a means of ground support. While proper design of backfill is important to ensure ground stability, understanding the failure mechanism and the various influencing factors in a filled block is essential. This paper presents a modified sliding failure model of a confined backfill block. The model considers both the gravity load of the backfill itself and the overlying load from fragmented ore or backfill on the top. A series of new equations were derived and the relationships between factors such as factor of safety, friction angle, cohesion and the exposed stope height were developed. This modified model will be a very useful tool in backfill design, for example, to optimize the design of backfill for a given stope geometry or to determine the maximum backfill height for a particular type of backfill.

May 1, 2007

By S. Dallaire

With the attainment of high temperatures it becomes possible to process any kind of material (particularly ceramics) in their liquid state. In the plasma spraying process, the material to be sprayed is rapidly heated until it is molten and is propelled by high velocity gases onto a surface where it adheres, to give protective coatings for a wide range of applications. The method could be considered as one of the most versatile and rapid to build up thick deposits (of plastics, metals, ceramics, cermets) and also free-standing artifacts for particular requirements without resorting to lengthy forming and sintering studies. Although plasma spraying is at the production stage in industry, advanced processes have also been developed for economically producing a wide range of new materials. This paper illustrates the benefits of the process and evaluates the challenges it represents.

Jan 1, 1987

By A. Liem, R. L. Johnson, C. Sturgess, E. Kuzub

New challenges in mineral processing arise as high-grade ores become less available and the mining industry is forced to exploit lower grade ores. One of the challenges in beneficiating lower grade ores is the liberation of mineral particles while maintaining control over material management. Lower grade ores need fine grinding to free valuable minerals, but finely divided particles can cause severe problems, such as dustiness and flowability, in subsequent stages of material management. There are at least two approaches that can be taken to resolve this dilemma, both of which relate to particle size enlargement. First, the application of a dust suppressant can be used to control that aspect of material management. The optimal choice of dust suppressant agent depends on effectiveness and cost, both of which can be strongly influenced by the selection of application method. Second, agglomeration combining small particles into larger units-can reduce dust and improve the flow characteristics of the material at the same time. There are several mechanisms that can be employed to agglomerate mineral materials. Although agglomeration adds a new processing step, it is often cost effective. This paper describes these two approaches and their respective challenges, as they relate to a mined ore. We report on modified or newly developed procedures for characterizing mineral ores with respect to material management. On the same material, we use agglomeration processing to capture fines within larger particles and show how dustiness and other aspects of material handling are affected. We conclude by discussing their specific application in accordance with the mineral properties and processing needs.

Jan 1, 2004

By M. Sider, D. L. Piron

"The cost of energy is a growing factor in the cost of zinc production. Electrowinning from sulphate solutions with periodical reverse current or from acidic chloride or alkaline solutions could be the way to lower costs. A comparison of the energy consumption for electrolysis shows that the alkaline solution may be considered the most promising alternative. IntroductionZinc electrowinning from sulphate solutions is a very energy intensive process (typical specific energy usage : around 3.1 kWh / kg zinc). This energy consumption represents 35% of the total cost of electrolysis and is the most important cost component.In order to lower costs, the energy efficiency of the sulphate process should be improved or alternative processes should be developed. In this laboratory, that objective has resulted in research on electro winning in sulphate solutions with the use of periodical reverse current (PRC) and in acidic chloride and alkaline solutions.Some of the results obtained in this laboratory and already published and new experimental results reported in this paper make it possible to present a more critical comparison of the energy consumption of the three processes mentioned.ExperimentalThe experiments at constant current were carried out as described previously. Specific conditions are indicated in Table I. Current efficiencies were obtained by weighing deposits.ResultsThe best energy consumptions for electrolysis obtained in this laboratory for the three media are presented in Table I. More detailed results can be found in the papers already mentioned."

Jan 1, 1988

By T. Thriveni, Ji Whan Ahn

"The current advanced technologies for the manufacture of light weight metals processing significantly increasing and attributes to the safety, performance, recyclability and economy. Still lack of technologies developed for light weight metals processing waste utilization and application. Environmentally friendly methods need to develop for better understanding the processing waste utilization. Alumina and aluminium processing creates a wide range of waste products, the most significant being is red mud. Bauxite residue is a high volume hazardous waste and nearly 3 billion tons have been dumped worldwide. Approximately, 120 Million tons/yr of red mud being produced without any environmental sustainable solution. Currently the most significant technology is waste utilization. The bauxite residue is suitable for road base construction, golf bunker sand, back fill and, general fill. Sustainable recycling technologies are necessary for the bauxite residue utilization for the recovery of rare earth elements and cement materials. Carbonation or CO2 sequestration of carbon dioxide is a method pioneered for the bauxite residue is modified to reduce alkalinity. The carbonation of alkaline material is an inexpensive and safe process that leads to the formation of thermodynamically stable products. The use of the carbonation can be an advantageous solution for environmental climate change and sustainability problems in the new century.INTRODUCTIONIn 2014, bauxite consumption was estimated to be 9.6 million tons, nearly all of which was imported, worth an estimated 269 million dollars. More than 95% of the bauxite was converted to alumina, and the remaining 5% went to non-metallurgical products, such as abrasives, chemicals, proppants, and refractories. Global aluminum demand is growing steadily spurred by growth in India and China (RBCAluminum Market Outlook, 2013) (Figure 1). Aluminum consumption is expected to rise 5% annually through the end of the decade, reaching 67 million tons per year by 2020. Global bauxite production decreased by 17% from that of 2013, principally owing to lower production in Indonesia. In response to a Government ban on exporting bauxite and other unprocessed mineral ores that took effect on January 12, 2014, bauxite mines throughout Indonesia shut down and production decreased from 55.7 million tons in 2013 to an estimated 500,000 tons in 2014. The ban was part of a mining law that was instituted in 2009 to increase development of downstream processing facilities in Indonesia."

Jan 1, 2016

By J. Bigu, M. G. Grenier, S. Hardcastle

"This study was undertaken in a belt conveyor drift of an underground hard rock mine. The conveyor transported ore or waste from a crushing operation located upwind from the drift sampling locations. A 250 m section of this drift was selected and several types of measurements were taken. Average respirable concentrations in the drift were 0.43 mg/m3 and 0.19 mg/m3 for total and silica dust, respectively. From the respirable dust concentration profile along the drift, it may be possible to estimate the contribution from extended sources such as dust produced by the belt and return idlers.The airborne dust in the drift had an average mass-median aerodynamic diameter of 4.2 micron. A continuous dust monitor showed that the crushing operation produced fairly high dust concentrations (sometimes greater than 4 mg/m3) over short periods of time.IntroductionAirborne dust in the respirable range is known to be the cause of various forms of lung ailments . In underground mines, respirable dust sources are created at many stages of production. All mining operators are responsible for de signing and establishing means of reducing airborne dust. In some cases, sources of dust are well defined and suppression methods are standard.In the case of interest here, the airborne dust cloud was formed from the contribution from many sources, which may be either discrete or extended. At the experimental site, the discrete or point sources were the crushing operation and the belt conveyor transfer point (tail pulley). These sources may be controlled by proper dust capture and scrubbing systems as well as dilution ventilation. Examples of extended dust sources in the area include dust produced by the re-entrainment of settled particles along the drift. Ventilation air movement and vehicular traffic both contribute to this phenomenon. Dust produced by the conveyor is another example of an extended dust source. Caked deposits on the return strand and idlers as well as the transportation of dry material on the belt, can be major contributors. Proper wetting of roadways and muck as well as proper belt cleaning techniques can help reduce these emissions. The cleaning apparatus, used on the belt where these experiments were conducted, is shown in Figure I. These and other belt cleaning techniques are described in more detail elsewhere."

Jan 1, 1987

By J. Etcheverry, E. Seguel, R. Díaz, F. Parada, R. Parra, E. Balladares

A thermodynamic and kinetic model is proposed to explain the formation of bornite, chalcopyrite and magnetite during partial roasting of enargite-containing copper concentrates. The proposed mechanism involves solid-solid-gas and solid-gas reactions between chalcocite, pyrrhotite, gaseous sulfur and oxygen. The formation of bornite could be explained by a two-step reaction: the first one involving the formation of chalcopyrite by a reaction between Cu2S, FeS and gaseous sulfur, followed by a second step in which the newly formed chalcopyrite reacts with additional chalcocite to form bornite. Although thermodynamically the direct formation of bornite is more favorable than that of chalcopyrite, the lower diffusion kinetics of bornite formation could explain the preferential formation of chalcopyrite. If the reaction occurs with stoichiometric chalcocite and pyrrhotite in the presence of gaseous sulfur to form chalcopyrite, no bornite is formed, while for the stoichiometric reaction between chalcopyrite and chalcocite in the absence of sulfur, only bornite is formed. For the formation of magnetite and chalcopyrite the mechanism could involve the partial reaction of chalcocite and pyrrhotite in the presence of oxygen. The proposed model is thermodynamically consistent with the experimental results obtained in laboratory and pilot plant. INTRODUCTION The processing of high-arsenic copper concentrates with over 0.7 wt.-% arsenic by conventional smelting-converting normally require an additional arsenic removal step to reduce arsenic content to levels below 0.2–0.3%. One of these high-arsenic copper concentrates is the one produced by the Ministro Hales Division (DMH) of CODELCO, which has the typical chemical composition shown in Table 1. Enargite (Cu3AsS4), chalcocite (Cu2S) and pyrite (FeS2) are the main mineralogical species present in these concentrates, with over 75 wt.-%, as shown in Table 2. Partial or “neutral” roasting of these concentrates under controlled temperature and partial oxygen pressure conditions at 923–993K (650–720ºC) can remove up to 95% of the arsenic as As2S3 (As4S6), which has a high vapor pressure under these conditions, leaving a calcine with low residual arsenic. In copper concentrates, arsenic is present generally as enargite and arsenopyrite. This compounds as well as others such as pyrite and covelite, decompose readily above 770 K (500ºC), releasing, in addition to gaseous arsenic trisulfide, gaseous sulfur which by oxidizing to SO2 generates most of the heat required by the process.

Jan 1, 2019

By Donald Leroux, Robert Grant

"Flotation is a complex and highly multivariate process. Using the conventional OFf (one-factor-at-a-time) technique, the optimization of flotation circuits through laboratory or plant testwork is difficult, time-consuming and therefore, expensive and often results in marginal improvements. The optimal operating conditions can be more efficiently estimated when a systematic approach like SDE (Statistical Design of Experiments) is taken.The concentrator of Noranda's Brunswick Mining Division (near Bathurst, New-Brunswick) is well known for the complexity of its differential copper-lead-zinc flotation circuits. One of them, the chalcopyrite-galena separation (or CuSep) circuit, is impacted by more than 20 variables.Statistical Design of Experiments (SDE) techniques were applied at the laboratory scale to improve the performance of Brunswick's CuSep circuit. Screening tests were conducted using Fractional Factorial designs while optimization tests were carried out based on Response Surface Modelling techniques like the Central Composite design. Every series of tests, without exception, revealed new information and process insights which led to significant circuit performance improvements in the plant So far, the metallurgical gain may be as high as four percentage points of copper recovery (in the CuSep circuit). Potential cost savings of expensive consumables (steam, activated carbon) have also been identified but will require additional circuit modifications before being realized.IntroductionIn spite of its apparent simplicity, flotation is a complex three-phase (solid, liquid and gas) separation process. Fundamentally, it is a highly multivariate process. Industrial flotation circuits are commonly affected by 10 or more process variables."

Jan 1, 1997

By F. L. Thompson

MAN has been using lubricants of one type or another for at least four thousand years, and probably for a much longer period. We have learned from the inner wall of the tomb of Tehuti-Hetep, on which is a decoration illustrating the method of moving a great stone statue, that as early as 1650 B.C. lubricants were used to facilitate the movement of heavy loads. The Egyptians had available nearly every animal oil and fat, as well as at least thirteen vegetable oils, of our time, all used for food products and in the arts. Examination of the deposit on the axle of a chariot from an Egyptian tomb of 1400 B.C. showed it to consist of animal fat, quartz, sand, iron, and compounds of aluminium and lime-indicating a manufactured lime-soap grease made with lime-soap and possibly tallow. This would not be a bad lubricant for the axles of chariots which had to travel over sandy soil in hot weather. As to the method of grease application, it is remarkable that, from the time wheels were first used in the far distant past up to the present day, no one has ever thought it necessary to design a seal to keep the lubricant in and the dirt out. While time certainly marches on, we have today, in waggons throughout the world, exactly the same form of lubrication as was used in the earliest chariots. From the early days of the chariot until shortly before 1800 A.D. (when the steam engine was introduced), the main heavy equipment required for mining purposes, for machines of war, etc., was made of wood. The bearings were rough, but usually they had metal in the lower half. Light machinery was made of bronze, brass, or iron. Large clearances and poor alignment, plus the fact that speeds were much below present-day demands, combined to provide conditions that were quite satisfactorily met by the lubricants available. These were often produced locally by the machine operator. In northern countries, lard oil, prepared from the fat of hogs, was the universal lubricant employed in machine shop, as a belt and leather dressing, and for cutting operations. Sperm oils were used for light machinery, whereas beef and mutton tallow were more generally employed for the largest bearings. For the early steam cylinders, a slug of heated beef tallow was injected wherever the cylinders gruntingly complained of a lack of lubricant. Southern countries, however, resorted to the use of vegetable oils-olive, cocoanut, etc.

Jan 1, 1940

By Aalbert Zwijnenburg

One of problems connected with the use of gold/titania-based catalyst systems is the low yield in propene oxide (up to 2 wt %). It is shown that the low propene oxide yield is due to product inhibition. New options for propene epoxidation with hydrogen and oxygen are discussed. INTRODUCTION The direct gas-phase synthesis of propene oxide (PO), by the use of molecular oxygen, is still aimed for. Agbased catalysis is in principle possible, but selectivity at present is not promising. Highly dispersed gold on titanium containing catalysts show an extraordinary selectivity in the oxidation of propene to the corresponding epoxide (> 99 %), using a combination of H2 and O2 as oxidation mixture [1]. Additional studies of the epoxidation reaction have indicated several drawbacks of the Au/TiO2 catalyst. Firstly, the low conversion (1- 2 %) obtained under typical reaction conditions (atmospheric pressure, 323 - 423 K) cannot be increased by increasing the reaction temperature, because this leads to extensive by-product formation. Secondly, the low efficiency of hydrogen (relatively large amounts of water are formed) is hard to prevent. Finally, significant deactivation of Au/TiO2 catalysts within several hours on stream has been observed. Deactivation can be almost completely prevented by using dispersed TiO2 supports, such as TiO2/SiO2 and Titanium-Silicalite-1 (TS-1) [2]. In recent literature [2,3] a hydroperoxide-like intermediate has been proposed to be responsible for the selective epoxidation. This oxidising species is said to be formed over gold and subsequently used for epoxidation over the Ti-containing support. The support is responsible for the slow desorption of PO. One of the problems for future industrial application might be the low yield in propene oxide. Furthermore, the presence of minor amounts of by-products, not detected on lab-scale catalyst testing, might complicate the separation unit in an industrial process. The reason for the low PO yield over Au/TiO2-based catalysts will be discussed in this paper. Temperature Programmed Desorption (TPD) and micro-flow experiments have been carried out to study PO desorption and catalyst performance, respectively. A catalytic cycle is proposed together with its consequences for the maximum yield in PO. Finally, several process and catalyst options are discussed in view of potential future industrial application.

Oct 1, 2003

By Jaime V. Ongpin

"The author will give a capsule history of Benguet Corporation and attempt to identify its operating environment and underlying ""strategy"" until 1974, when the company's management assumed office. The company's operating environment and ""interim strategy"" from 1975 to 1980 will be described. The discussion will cover an environmental forecast and define the company's"" strategy for survival"" for the balance of this century.IntroductionIn December last year, I was asked to deliver a pa per for the management lecture series a t the Asian Institute of Management in Manila. The paper was entitled "" The 1970's: A Decade of Disaster For New Mining Projects"" . In that paper, it was my task to review the results of new mining projects in the Philippines during the previous decade. The task was not a happy one, for the results themselves were not only unhappy, but disastrous on a scale unprecedented in Philippine history. Out of a total of 17 major mining project s involving an aggregate capital investment in excess o f US $2 billion during the 1970s, only three project s have been profitable, and all the rest have either gone "" belly up"" or are teetering on the very edge of financial disaster.It is in the context of this shocking record of widespread financial dislocation in the Philippine mining industry, (which in varying degrees appears to have been paralleled in virtually every other country in the world where mining is an important sector of the economy) that I address myself tonight to the theme of this symposium. My paper is entitled ""Risk Management Strategy in Mining"" and it is sub titled ""Can Benguet Corporation Survive to Celebrate its Centennial in 2003?"". I have inserted the word ""Strategy"" and added the subtitle, because I wish to make it clear first, that my presentation to you tonight will be focused exclusively on the strategic aspect s of risk management, and second that I will limit myself to Benguet's own ""in-house"" experience and perspectives on this subject. I would caution you therefore, to consider my views within this restricted framework, and in light of the particular and sometimes peculiar circumstances within which Benguet Corporation operates."

Jan 1, 1983

By K. Sinding, R. Poulin

"Recent land-use decisions in British Colwnbia, and the publication of a report on compensation for expropriations of resource interests, have highlighted the nature of land use policies. Landuse decisions, such as the creation of large new parks, raise three principal issues which have implications for how land-use policy is conducted and how it impacts on the mining industry. The first is the identity of the parties advocating different land-use policies and their motives for doing so, the second is the changing nature of benefits derived from land, and the third is the change of property-rights regime which is devised to accommodate the (changing) benefits from using land and natural resources, as well as the interests of the different parties involved.Involved Parties and BenefitsThe process of establishing or modifying property rights depends on the interest groups involved. Three distinct categories, each with distinct incentives which can influence the process, must be distinguished: private claimants, politicians and bureaucrats (Libecap, 1989).The first groups claim rents and management powers through asset ownership. They may be incumbent owners seeking enforcement of the status quo, new claimants seeking redistribution of assets, or third parties who depend on the distribution of assets (e.g. lenders, labour suppliers and contractors). Some infonnal property arrangements can be negotiated within the group whereas others requires action in the political arena through lobbying politicians for (re)allocation of property rights and influencing bureaucrats for favourable administrative decisions. The second category is politicians, who direct the powers of the state to change or enforce property rights. Both incwnbents and office-seekers fall in this category and their actions and opinions are shaped by their constituencies and financial backers. However, not all causes can be championed and trade-offs have to be made, resulting in decisions that maximize political benefits. The third category of parties in the process is the bureaucrats. The power to manage has been delegated by politicians but bureaucrats also have opportunities and incentives to further their own interests. These can include maintaining or expanding jurisdictional turf or increasing operating budgets (Libecap, 1989)"

Jan 1, 1994

By Robin E. Goad

?Located 160 Km northwest of Yellowknife, NWT, Canada Current winter road access ?New all-weather road planned ?Power within 22 km ?Hwy to Edmonton 80 km south Close to existing infrastructure

May 1, 2006

By Bong Sun You

AZ31 magnesium plate of 300mm in width and 40mm in thickness was produced by horizontal continuous casting machine, and its microstructures were analyzed on the surface and in the plate interior. The defect formation on the surface and subsurface, such as side cracks, buckling, pores and segregation, was very sensitive to the casting condition and processing parameters. Especially, casting speed and secondary cooling were the most dominant parameters to control the solidification behavior of magnesium melt, for example the position and shape of the solid/liquid interface in the mould. The cyclic marks on the surface were obvious because the plate were drawn by 4-step cycle and can not be removed. The average grain size of as cast plate measured as 50-65µm at the near surface and 300-400µm in the center of the plate was relatively small because secondary cooling water was applied to control the surface quality resulting in rapid solidification of the melt in the mould.

Jan 1, 2006

ABSTRACT The SART (sulphidization, acidification, recycle, and thickening) process is an effective way to separate copper and cyanide in the waste stream of gold processing plants using cyanidation. Factorial experimentation has been conducted to create models of copper recovery, cyanide recovery, acid addition, and oxidation/reduction potential during SART. Economic analysis of the resultant models showed that SART is best operated with a sulphide-to-copper molar ratio of approximately 0.56, pH of 4, and a minimized cyanide-to-copper molar ratio. The experiments also showed th0at residence time can have drastic impacts on SART performance.

Jan 1, 2013

By Asanga S. Nanayakkara

The surface deformations induced by reservoir dilations can be measured using tiltmeters and these measurements can be used to infer reservoir level volume changes by solving an inverse problem. Preferred approach to solve such an inverse problem is to consider more tiltmeter measurements than the number of unknown variables considered in the inverse problem. However, sufficient number of measurement points is not always available due to economical and practical issues. This paper proposes a new approach to circumvent this problem. The new approach entails generation of pseudo surface deformation data by curve fitting tiltmeter measurements using a mathematical function, which delineates three-dimensional characteristics of surface deformation profiles. Then a three-dimensional inverse problem is solved using pseudo surface deformation data. This method is useful in inferring reservoir volume changes with high areal resolution when the number of available measurements is not sufficient to acquire the desired areal resolution.

Jun 1, 2012

By Carl Faessler

Abstract Some Canadian geologists believe chat, in the Grenville sub-province of Eastern Canada, there is no granitic intrusion older than the anorthosite. The writers are among those who hold the contrary view. They suggest a new means to distinguish between rocks belonging to intrusions respectively older (Laurentian) or younger (Pine Hill) than the anorthosite. This new method is based on microscopical observations which demonstrate that the Pine Hill intrusives contain a large amount of exsolution perthite, whereas the Laurentian intrusives are completely devoid of exsolution perthite. Where perthite is present in Laurentian rocks, it is the result of lacer hydrothermal replacement. Introduction The present paper is the result of a systematic study of some acidic intrusive rocks in the Grenville sub-province. These rocks underlie large areas of the Canadian shield in the Province of Quebec, mostly along the southern border of the shield.

Jan 1, 1946

By Jaana Romppanen, Satu Jyrkönen, Tiina Ranki, Peter Björklund, Markku Lahtinen, Kaj Eklund, Päivi Suikkanen

Outotec is continuously developing our existing process equipment and new equipment solutions to enhance the Flash Smelting process. Thanks to the long operating history of the Outotec Flash Smelting process feedback from the numerous operating references are available and is utilized. The general goals for development work are to improve equipment performance, thus realizing savings in Smelter plant operation costs by increasing the process efficiency and online availability. Digitalization also opens new possibilities for the feeding equipment and furnace operation monitoring. These solutions will improve the safety and performance of the smelter, and provide process and equipment related information which has not been available earlier. INTRODUCTION The year 2019 marks the 70th anniversary of Flash Smelting. The technology was operated on industrial scale for the first time at the Outokumpu Harjavalta copper smelter in Finland in 1949. The Flash Smelting technology, is now owned and developed by Outotec Oyj and the first plant, is now owned by Boliden Harjavalta Oy. The two companies have been evolving throughout history by optimizing the process for various feeds and raw-materials, as well as through developing the equipment and operating practices. Even though sustainability was not a hot theme/topic during the first days of Flash Smelting, it has nevertheless been the key principle in guiding the development. This is well proven by the wide adoption of Flash Smelting for the processing of copper and nickel concentrates, mostly due to its ability to fulfil the economic and resource efficiency criteria demanded by its operators. Along with the process technology development, also development of the equipment has taken place over time. Outotec is continuously working on developing our equipment to better suit the changing need of our customers in the continuously changing operational environment. Orebodies are getting more challenging with lower ore grades and more impurities. Achieving high recoveries for all valuable elements becomes more difficult with high slag quantities and with the need to tackle the high impurity concentrations. There is a need for higher capacities in greenfield and brownfield smelters. The role of the Loss-in-Weight Feeder, the Air Slide and Concentrate Burner is to ensure even feed into the reaction shaft of the Flash Smelting Furnace, and to enable controlling the process well, thereby enabling the best performance for the customers smelter. The design of the Flash Smelting Furnace aims for high availability, long campaign and safe operation.

Jan 1, 2019

By R. D. Studer

"The Snow Lake massive sulphide deposits are hosted by Aphebian volcanic rocks of the Flin Flon - Snow Lake greenstone belt, which in this area were deformed and metamorphosed to the amphibolite facies during the Hudsonian orogeny. All the known deposits occur in felsic rocks a short distance below the contact with an overlying mafic rock unit.The Stall Lake copper deposit occurs close to the top of an explosive felsic volcanic sequence. Rocks stratigraphically underlying the deposit have been hydrothermally altered by the mineralizing fluids. The sulphides were probably deposited from submarine volcanic vent(s) on the flanks of a felsic dome. The ore has been tightly folded, flattened and elongated parallel to the northerly trending lineation of the surrounding rocks during the several periods of deformation. Strike lengths of the lenses range from 60 to 300 feet and plunge-to-strike ratios are as much as 15:1.Ore lenses I to 4 typically consist of massive coarse-grained pyrrhotite, chalcopyrite and pyrite. A stratigraphically higher lens differs in that it contains fine-grained pyrite and chalcopyrite, with an increase in sphalerite toward its hanging wall. The No.4 orebody has a distinct footwall alteration zone characterized by brecciation and abundant chlorite-staurolite- garnet schist, with minor kyanite, anthophyllite, cordierite and anhydrite, as well as sulphide minerals. Chemically, the alteration zone is distinguished from the unaltered felsic rocks by Na20 depletion and Mg-Fe enrichment"

Jan 1, 1982

By P. B. Demarsh

"Location: - On highway 59, 17 miles east of Val d 10r near junction of Montreal highway in Northwestern Quebec.Life; - Started production 1952, ceased 1965.Ore: - Pyrite, chalcopyrite and small amounts of free gold and goldsilver tellurides in narrow quartz-carbonate-tourmaline veins in granodiorite. Specific gravity 2, 70.Capacity: - 700 tons daily Bevcon ore supply, l 000 tons daily when custom ore available.Assay: - Heads 0 .140 oz. per ton; tails 0. 009 per ton; extraction 92.5%.Grind: - 75% minus 200 mesh at 700 tons; 68% minus 200 mesh at 1000 tons. Detention time 28 hours and 21 hours respectively.Treatment: - Cyanidation process.Reagents: - Per ton. Aero Cyanide (NaCn) 0, 50; crushed unslaked lime 1. 75; zinc 0. 03; litharge 0. 10; steel consumption 2. 25.Water: - Pumped from land-lock spring fed lake l 1/2 miles distant.Cost: - Per ton. Crushing 0. 13; grinding 0 .32; filtration 0. 07; cyanidation 0.14; miscellaneous 0.29; total 0.95.Power: - Hydro-electric, 25 cycle, 12, 000 volts reduced to 550 volts.Labour: - Predominantly French Canadian, nucleus English Canadians.Tailings: - Impounded low lying pond.Personnel: - 15 including supervision.Flow sheet: - Canadian Mining Manual l 9 5 6 .Building: - Wood truss construction: 3/ 4 in. siding, ten test and 1/ 4 in. transite outside. Corrugated galvanized iron roof. Ground level foundations. Internal self induced heating. Wood stave tank equipment."

Jan 1, 1966