Search Documents

By J. W. Griffith

"The mines in the Bancroft area of southeastern Ontario, a few kilometres west of the town of Bancroft, are in Faraday and Cardiff Townships. Three companies, known as Canadian Dyno Mines Limited, Macassa Gold Mines Limited (Bicroft Division) and Madawaska Mines Limited (formerly Faraday Uranium Mines Limited), with plants capable of handling a total of 4,()()() tons (3,629 tonnes) of ore a day, were at one time in production. A fourth company, Greyhawk Uranium Mines Limited, operated a small mine whose ore was shipped for custom treatment to the nearby Faraday mill. Canadian Dyno Mines Limited ceased operations in June 1960. In June 1963 the Bicroft Mine was closed and a year later Faraday closed because of contract completion. But in 1975, Faraday (now called Madawaska) was re-opened but closed again in 1982. During 1959, the peak year, these four mines produced an estimated 1,100 tons (998 tonnes) of uranium precipitates, which represented nearly 7 per cent of Canada's output for that year(Fig. 1).The deposits occur in pegmatitic granite dykes in a region of high-grade metamorphic and metasomatic rocks. Uranium distribution is usually controlled by the distribution of mafic minerals, particularly hematite and magnetite, and by late fractures. The best visual indicators for uranium concentration are hematite staining in the pegmatite, followed by the amount of mafic inclusions or crystals. The Bancroft area orebodies are the only known deposits of the general pegmatitic class in Canada that contained economic deposits of uranium. The principal radioactive minerals are uraninite and uranothorite. By comparison with many other pegmatitic occurrences, some of the ore bodies are unusually large, persistent in depth and relatively rich in uranium minerals. At the end of 1981, total ore reserves were estimated at 1,500,00 short tons (1,360, 000 tonnes) averaging 0.11 % U3O8."

Jan 1, 1986

By G. Chung, W. Petruk, D. Doyle

"A series of tests was conducted on Carol Lake iron ore, which contains about 38 wt % hematite and 19 wt % magnetite, to establish a flowsheet for high weight yield by spirals. A pilot plant was run in parallel with the IOC concentrator to simultaneously test two flowsheets on the same feed material. The IOC concentrator processes the ore by treating it directly in a spiral circuit, whereas the pilot plant used a laconite flowsheet which had a low intensity magnetic separator (LIMS) at the front of the circuit. The LIMS produced a non-magnetic (hematite-rich) product and a magnetic (magnetite-rich) product prior to treating the ore in two separate spiral circuits. The results from about 150 tests were evaluated by chemical assays and materials balancing techniques, and a selected test was evaluated by the image analysis and materials balancing technique.The image analysis and materials balancing evaluation showed that a higher hematite recovery was obtained by the hematite spiral circuit than by the IOC concentrator spiral circuit, and a slightly lower magnetite recovery by the magnetite spiral circuit than by the IOC concentrator spiral circuit. Furthermore the hematite recovery by hematite spirals was higher than the magnetite recovery by magnetite spirals. The better hematite recovery was achieved because a higher liberation is obtained for hematite than for magnetite, and the hematite in the Carol Lake ore has a narrower grain size range than magnetite. Consequently, better spiral control can be maintained when processing a hematite-rich spiral feed, than when processing a magnetite-rich spiral feed. Since the feed to the IOC concentrator spiral is a mixture of hematite and magnetite, an intermediate hematite recovery is obtained by the IOC concentrator. INTRODUCTIONA study of characteristics that affect recoveries of hematite and magnetite from the Carol Lake ores of the Iron Ore Company of Canada (IOC), was carried out in connection with a project on designing a flowsheet for maximum weight yields. A pilot plant using a taconite flowsheet was run in parallel with the existing IOC concentrator which uses a classical iron ore flowsheet. About 150 tests were run to compare iron recoveries and weight yields by the spirals in the two flowsheets. Better iron recoveries were indicated for the taconite flowsheet, but the results were not consistent and the reasons for the observed differences were not apparent. The material from one test (Test 61), which gave better iron recoveries for the taconite flowsheet, was evaluated by the image analysis and materials balancing technique. A suite of samples was taken from 5 points in the IOC concentrator and from 8 points in a pilot plant (taconite flowsheet). The samples were analyzed to compare the behaviours of the Carol Lake hematite and magnetite in the spirals of the two flowsheets. The results provided a sound basis for further tests in designing a high weight yield flow sheet."

Jan 1, 1993

By Kwang-Hyun Jeon

Recently, 3D printing technology in the manufacturing field is in the spotlight. In the construction industry, similar rapid prototyping technology that does not use conventional form can be applied to meet the demand on free formed structure that can provide aesthetic value and functionality. Conventional formwork can increase construction cost and period for various structure with complex shapes while it has numerous advantages such as high strength, convenience, accuracy and good quality of surface roughness. To meet the demand on free formed structure, automated freeform construction systems such as Contour Crafting and Concrete Printing have been developed with active collaboration between university and industry in USA and England. However, details on the system have not been fully released in public, so the possibility of its fusion and spin-off technology cannot be expected. In this paper, cost-effective solution for mechanical and control system for constructing a free curved structure without mold are described. As an appropriate material for the system, fiber reinforced mortar was selected by experiments on compressive strength, setting time and fluidity. After performing G-code simulation, transfer and extrusion experiments with the selected mortar mix were performed and the possibility of the development of automated freeform construction system was demonstrated. Based on this research results, it is required to keep the automated freeform construction system improve and extend it into the new application area in construction industry.

Aug 1, 2013

By Lauri Gregg

How Can Man Meet the Carbon-Free Energy Challenge ? ? Increases in Energy Efficiency can displace 1/2 to 2/3 of the Carbon-Free Energy required to stabilize at 550 ppmv ? Renewable Energies require too much land and thus can displace 5 to 10 % of the energy requirement ? Large new sources of carbon free energy are needed ? Conservation is desirable but provides only a small and variable contribution ? People will have to adjust to higher levels of CO2 in the atmosphere as energy demand continues to grow

Nov 1, 2002

By J. F. Magee

THERE is nothing new about drag-line dredging for placer gold. The use of the separate unit for excavating preceded the large barge with bucket-line excavator mounted upon it, which has developed to a high state of perfection through use in every part of the world. But at present there is a vogue for a small, inexpensive plant to work economically the shallower gold gravel deposits that the bucket-line dredges do not work. The dragline dredge consists of the drag-line excavator, on caterpillar mounting on the edge of the dredging pond, which feeds the gravel to the washing plant, mounted on a floating barge in the pond. There have been more than twenty-five such plants built and operated in central and northern California and an unknown number in other States. There have been variations in details of design but the essentials are similar in all. I wish to describe the operation of a typical drag-line dredging plant, that of the Wyandotte Gold Dredging Company on the Farnan Ranch in the Oroville district. This organization of six active partners built their first plant on Wyandotte creek in the autumn of 1933. The operation was successful due to wise management, which was based upon good plant design and proper principles of operation. The partners elected one of their number, H. F. England, as manager with full control and responsibility. This plant and operation furnished the pattern for many subsequent ones.

Jan 1, 1937

By L. Voisin, G. Damm

"In order to develop a new pyrometallurgical process for eliminating detrimental arsenic and antimony from the impurity-rich matte produced from copper concentrate, and for treating the occasionally generated speiss in nonferrous smelting processes, the phase relations in the Fe-Cu-S-As-Sb system saturated with carbon at 1473 K were investigated. The distribution of elements between the condensed phases at the miscibility gap, where three equilibrated phases of iron-rich alloy, copper-rich alloy, and matte coexist, were also studied. The investigation was carried out by performing a series of laboratory scale experiments in an electrical furnace at 1473 K, followed by a quenching method on the final stage. The samples obtained from the experiments were analyzed by using Inductively Couple Plasma (ICP), Atomic Absorption Spectroscopy (AAS) and Carbon Infrared Spectrometry (CIS) techniques.The results were compared with previous investigations for the Fe-Cu-S-As-C and Fe-Cu-S-Sb-C systems and discussed on the basis of the molar fraction distribution for both arsenic and antimony in the matte phase at five different matte grades. It is expected that by using this phase separation technique it might be feasible both, the cleaning of a complex copper matte and the elimination of arsenic and iron together with an acceptable amount of antimony into the iron-rich alloy phase, which can be discarded as a harmless and smaller deposit."

Jan 1, 2014

By Guy Chevalier

QCM?s pellet plant, located in Port-Cartier, Quebec, produces up to 8.6 million tons of iron ore pellets annually. Four different types are produced: three for blast furnace operations and one for direct reduction furnaces. The paper presents the scientific approach that led to the installation of new process equipment to improve the reducibility of direct reduction pellets (DR pellet). The findings, the equipment selection and some post start-up modifications are presented. This low silica DR pellet is used in Midrex and HyL shaft furnaces. A good DR pellet has to meet strict chemical, physical and metallurgical specifications. An important metallurgical property is its ability to release oxygen when exposed to reducing gases. Considering that the market for DR pellets is expanding and being aware that reducibility is critical for our clients, a program to improve the latter was undertaken. Test work showed that one factor which has a negative effect on reducibility is the proportion of particles larger than 75 microns. Knowing that the best way to reduce the amount of coarse particles was to close our open grinding circuits, we began evaluating the most suitable classification equipment applicable to our process operations. We settled on hydro-classifiers based on their very sharp cut and their low operating costs. In light of the hydro-classifiers performance it was also decided to replace the hydro-cyclones of an already closed circuit.

May 1, 2003

"The South African Mineral Resource Committee (SAMREC), a Working Group of the SAMREC/SAMVAL Committee (SSC), under the joint auspices of the Southern African Institute of Mining and Metallurgy (SAIMM) and the Geological Society of South Africa (GSSA) developed the SAMREC Code. The Code sets out minimum standards, recommendations and guidelines for public reporting of exploration results, mineral resources and mineral reserves in South Africa. It is applicable to the reporting of all styles of solid mineralization or economic deposit. However, certain commodities, namely coal and diamonds, have specific additional reporting requirements. The Code does not apply to oil, gas or water."

Jan 1, 2003

By Maurizio Violo, Arjan Beqiraj, Umberto Masi

"Abstract - Four main podiform occurrences of chromite have been distinguished in the ultramafic Bulqiza massif, Albania; they are associated from the bottom to the top with: i) basal harzburgites (lower tectonite sequence), ii) dunitic lens-bearing harzbugites (middle-upper tectonite sequence), iii) layered chromitite-bearing dunites of transitional zone, and, iiii) the stratigraphically lowermost part of the magmatic section. However, only the occurrences hosted by rocks ii) and iii) are economically important.Chromite compositions similar to those of other podiform chromites are bimodal. Thus, chromites from occurrences ii) and iii) are richer in Cr than chromites from the other two occurrences. Accessory chromite disseminated throughout the massif is richer in Fe than orebody chromite, displaying similar range of the Cr/Cr+Al ratios, with accessory residue chromite matching the characteristic (Cr/Cr+Al >0.6) range of type-III Alpine peridotites. Both orebody and accessory chromites show compositional ranges correlating with host-rock compositions, i.e., the Cr-rich chromites are hosted by the most refractory ultramafic rocks. Therefore, the Cr/Cr+Al and Mg/Fetot (Cr/Fetot) ratios of chromite are useful for exploration of high-grade, metallurgical chromite ore at Bulqiza and in other massifs of similar geodynamic setting."

Jan 1, 2000

By Masashige Makifuchi, Hiroki Kumakura, Kota Nagai, Takahiro Kikuchi

"A large amount of platinum group metals (PGM) are used in automobile catalyst. It is important to recover the metals from wasted catalyst. Nomura and Kageyama (2013) suggested recovery process that PGM oxides were absorbed to perovskite-type oxide based on LaScO3. In their process, the PGM in wasted catalyst as absorbed to the perovskite-type oxide as PGM oxide. It has potential to each element in the process if the perovskite-type oxide is selected properly. In this study, the PGM oxide absorption properties of various perovskite-type oxides are investigated to develop a new recovery and separation process. The various perovskite-type oxide were synthesized with metallic platinum, palladium, rhodium at high temperature in air atmosphere. And the PGM contents in the perovskite-type oxide after the experiment are determined by chemical analysis. Some of them have the properties to absorb specific PGM oxide selectively. In addition, in order to increase the amount of absorption of PGM oxide and composition of the perovskite-type oxide experimental temperature was investigated. Then it is also found that doping another specific element to the perovskite-type oxide is effective to increase the amount of absorption of PGM oxide. Then a new recovery process of PGM from wasted automobile catalyst, in which PGM can be separate to each element, was designed.INTRODUCTIONA large amount of Platinum (Pt), Palladium (Pd), and Rhodium (Rh) are used in automobile catalysis (Figure 1) (Platinum, 2013). Natural supplies for these metals are limited and PGM mining can detrimental environmental impact. Therefore, the recycling of PGMs from wasted automobile catalysis is very important. The Rose process (Figure 2) was developed as a process to recover PGM from wasted automobile catalysis. In this process, the automobile catalysis is first crushed mechanically, and then extracting agent, copper (Cu), and flux are melted at high temperature. The mixture separates into a metal phase, (Cu alloy containing PGM) and slag. The PGM is enriched by oxidizing. Cu to Cu oxide. The PGM are then recovered and separated to each element in a wet process. However, it is hard to dissolve the PGM with acid because they are chemically stable and strong oxidation agent such as aqua regia is used. Moreover, to separate the PGM to each individual element, a solvent extraction process is required."

Jan 1, 2016

By E. S. Moore

GOLD was discovered previous to the year 1900 on the east shore of Emerald lake, Afton township, Timagami Forest Reserve. It was found in a small cavern in banded iron formation, close to the water's edge. This occurrence of gold was mentioned in several reports that referred briefly to this area, and prospectors evinced considerable interest in the region. It was not, however, until the Golden Rose Mining Company, which was incorporated in 1909, started operations that much work was done on the property. In 1915-16, this Company, under the direction of E. J. Townsend, the President, did a considerable amount of work. A small mill was built and ore was extracted from pits, trenches, and a one~ hundred-foot shaft. In 1927, Afton Mines, Limited, was incorporated to take over the property, and about thirty men were employed for a time. During 1934, the New Golden Rose Mining Company was organized to handle the property, and the Consolidated Mining and Smelting Company of Canada, Limited, undertook to develop the mine. In March of the following year, this Company began deepening the shaft from 100 feet to 500 feet. A considerable amount of drilling had previously been done on the hill of iron formation in which the mine is located. Further drilling was done from the surface, and altogether about twelve holes have been put down to test the formations. Over 2,000 feet of drilling has also been done from the underground workings. The mine is now known officially as the New Golden Rose mine, although to many it is better known as the Afton. To reach the property during the summer months, there is a boat trip of about thirty miles from Timagami, a wagon-road portage of one mile to Obabika lake, a boat trip of ten miles on this lake, and finally a wagon-road portage of one and one-quarter miles to Emerald lake. The mine lies about three-quarters of a mile down the east shore of the lake. A 75 h.p. Diesel engine and compressor were taken in over this' route last summer, and it is evident that the transportation problem is quite a serious one. Airplanes have been much in use, and a winter road runs from the mine to Chudleigh, on the .Canadian National railway near Sudbury.

Jan 1, 1936

By W. R. Middagh, R. M. Garvey

"Phosphate rock is shipped by boat from Florida to Vancouver, B.C., where it is unloaded and stored in a 50,000-ton silo. It is shipped from Vancouver in 100-ton hopper cars in 80-car trains to Fort Saskatchewan. Both the ship and the hopper cars are on a back-haul with potash. The rock cars are unloaded at Fort Saskatchewan at a rate of approximately 4 cars per hour. The rock is stored in three concrete silos, 40 ft in diameter by 110 ft high, which hold 18,000 tons of recoverable rock with 2,000 tons dead space. The rock is reclaimed from the silos by gravity and fed to the phosphoric acid plant by remotely operated conveying equipment.Problems encountered in the operation include scheduling the rock shipments, contamination of the rock with potash, and handling the 80-car trains both in Vancouver and Fort Saskatchewan."

Jan 1, 1968

By D. E. Ayres, J. Farstad

"The Midwest uranium deposit is located within the Athabasca Basin near its eastern margin and displays many of the features seen in a number of other similar deposits in this area. The mineralization occurs in the vicinity of a tectonically disrupted portion of the unconformity separating the clastic sedimentary rocks of the Helikian Athabasca Group from Aphebian pelitic meta-sediments which are equivalent to the basal pelitic meta-sediments of the Wollaston Group. The orebody consists of pods of massive pitchblende and sulphur-arsenides within an elongate and tablular envelope of disseminated and fracture controlled mineralization. The massive pods are intimately associated with overbank mudstones of the lowermost Athabasca Group. Both structure and lithology have played major roles in localizing the deposit as follows:1. The basement lithology influenced the mineralogy of the regolith produced on the pre-Athabasca unconformity.2. The style of clastic deposition and the character of the regolith on this unconformity favoured local preservation of mudstones.3. The basement lithology influenced the location of zones of post-Athabasca faulting.4. The proximity of these fault zones to mudstones provided for the coincidence of circulatory channels for fluids bearing uranium, with a good precipitant for the metal.IntroductionA brief summary of the geology of the Midwest uranium deposit was presented by J. Farstad (1979) to the attendees of the Saskatchewan Potash and Athabasca Basin uranium deposits field trip organized by the Canadian Institute of Mining and Metallurgy (May 28 to June 1, 1979). Since that time a substantial amount of data has been collected and studied. This paper is a precis of a report by J. Farstad (1981) which summarizes the geology of the deposit as inferred by visual examination of diamond drill core, augmented by information obtained from detailed examination of selected cores by D.E. Ayres."

Jan 1, 1986

By Don McColman

"Tires, although not always the largest single cost item in open-pit mining operations, will place in the top three, along with explosives and fuel. How this high-cost supply is controlled is dependent upon on an efficient tire program. The success of this program is, in turn, dependent upon the people who are directly associated with tires and their use, namely: the mine's tire personnel, the tire sales representatives and a technician for the rubber company. The technician will relay his observations and information received from the mine personnel back to the manufacturer with recommendations to overcome current problems .Haulage truck tire life and costs in a hard rock open-pit mine are governed and controlled by four important factors:I) Field control.2) Operating within manufacturer's guidelines.3) Different tire purchasing methods.4) Scrap piles.Field ControlPerhaps the most influential people involved in this program are those who live with the tire through every hour of its lifespan: the truck driver, the shovel operator, the dozer operator, the grader operator and the shift boss. Of these, the truck driver has the most control, in that he can drive over or around rock s as these situations arise. The loading area, the edge of the haul road and the dump account for most of the tire injuries.This is why shovel, dozer and grader operators must appreciate their influence on haulage tire life. Spillage cleanup must be ongoing and is not being done adequately if any of these operators are idle. The shift boss that drives by a rock on the road without removing it or calling for a cleanup has little recourse with the truck driver who runs over it-he has sanctioned the driver's actions by his own neglect."

Jan 1, 1986

By A. J. Sinclair

Abstract-Exploratory data evaluation is an essential part of every high quality, mineral inventory estimate. Efficient analysis involves a thorough organization of available quantitative data that are the basis of the estimate and perhaps the formation of composite grades. Data organization and evaluation can involve more than 50% of the time necessary to conduct a mineral inventory estimation. The principal purpose of exploratory data evaluation in mineral inventory work is to improve the quality of estimation by providing insight into characteristics of the variables under investigation. Specific aims include: (1) to recognize and eliminate errors; (2) to provide a comprehensive knowledge of the statistical characteristics of all variables of interest for resource/reserve estimation; (3) to document and understand the interrelationships among the variables of interest; (4) to recognize systematic spatial variation of variables such as grade and thickness of mineralized zones; (5) to recognize and define distinctive geological domains that require independent estimation of mineral inventory; (6) to identify and characterize outliers; and (7) to evaluate similarity/dissimilarity of various types of raw data, especially samples of different supports. These aims are not mutually exclusive but they can all have their own impact on resource/reserve estimation. Error must be minimized. Individual variables can have characteristics that lead to different decisions in the course of estimation. Similarly, interrelations of variables might contribute to the ease (or difficulty) with which estimates of several variables can be obtained. Trends can impose the need for two or more domains, each of which might be estimated independent of the others. Outliers, a perennial problem, require detailed evaluations because they impact on reserves much out of proportion to their abundance. Data, of widely different supports, generally must be standardized if all are to be used for purposes of estimation.

Jan 1, 1998

By A. Saigal

The effect of temperature on the cutting forces during machining of alumina reinforced aluminum composites was investigated, Aluminum 6061, 10% Al2O3 reinforced composite and 20% Al2O3 reinforced composite were tested, A 5/8-inch diameter high-speed steel end mill, a Micro 100 TiN coated single edge endmill cutter and a two-fluted solid carbide insert cutter were used for tooling, The results, in general, showed an increase in the cutting forces as the temperature of the material increased, From the raw data, there are temperatures ranges in which the force data did decrease but they were insignificant with regards to predicting a downward trend. A regression analysis was used to understand which variables had the greatest affect on the forces being generated, The correlation and regression analysis showed that at 600 rpm (velocity: HSS- 98,2 sfpm, Micro 100 cutter - 78,5 sfpm, solid carbide cutter - 192,4 sfpm) the tooling, the workpiece material, built up edge, and temperature were statistically significant factors in the test, Tooling was a significant variable in all testing, The smallest forces recorded during machining were generated with the solid carbide two-fluted endmill cutter, Visually, the solid carbide tooling produced a better surface finish during the testing which made it the tool of choice, In addition, the force data proved that as the cutting speeds were increased, the cutting forces decreased.

Jan 1, 2005

By P. Molera

"In Catalonia, between the 10th century and 1878, some installations were developed which at first were called ""factories"" and later ""fargas"", since they manufactured iron and steel of low carbon content. Because of its excellent quality, the fame of this metal spread from Catalonia to many countries. Fargas were started in Corsica, the Low Countries, Germany, Oriental India, Madagascar, Finland and along the rivers Orinoco and Mississippi among others. The extractive process used in these fargas has passed into history as the ""Catalan Farga Process"", ""Catalan Process"", or just ""Farga Catalana"". With this technology, raw material was obtained for the fabrication of tools, nails, weapons, grilles, etc. to supply the national and export markets. Aside from meteorites and native iron, found as metallic nodules in basalts in Greenland and Palestine, the ancient civilizations, which had no means to reach the fusion temperature of iron (1535°C), obtained iron by a direct process. Similar processes were used until quite recently (1930s) by certain tribes in Central Africa; holes in the ground were filled with iron ore and coal, and combustion encouraged by blowing air by mouth or with bellows made of animal skins. Thus without melting the iron it is possible to reduce the mineral and obtain a porous and impure metallic mass, which is purified on forging by mechanical squeezing. With a process very likely similar, the famous column at Dehli weighing 6.4 m.t. was built about 300 B.C."

Jan 1, 1999

By R. Heikkilä

Fluent information exchange between different work phases, software and systems used in infra construction is a key for successful execution of infra construction projects. Open and publicly available information formats with the determined data models aim to facilitate the interoperability between different software and systems developed by competitive vendors. While building and construction industry has developed and used IFC format for years, infrastructure sector has just recently started to target clear efforts on the development of open information formats for infra construction processes. In the paper, a new Inframodel3 extension just developed in Finland and based on the LandXML1.2 international standard is to be introduced. The aim of the Inframodel3 was set to meet the requirements of information transfer needed especially between BIM based design software, measurement systems and 3-D machine control systems used in road, railway and watercourse construction projects. Some test results are reported and evaluated in the paper. In the field of bridge engineering, the IFC format and IFC Bridge extension have been tested and evaluated in Finland. The results from the experiments show and verify as well the applicability of these open formats to the information exchange requirements in bridge engineering. The current limits for open information transfer of these formats are shown. The active co-operation with the International Building SMART Organization has led to the achieved status and position for both the Inframodel3 and IFC Bridge formats and hence the continuing international support provided by Building SMART.

Aug 1, 2013

By X. J. Luo, F. Zhang

"Metallurgical slag (MS) such as steel slag, copper slag is a renewable resource and its compressive strength exceeds 200MPa in general. Because pure metal slug can easily be mixed into MS, complex recycle system is necessary in order to realize MS’s recycling. Meanwhile, there is high equipment failure rate in conventional crushing system. New crushing systems with inertial cone crusher could solve this problem very well. Recovery rate of MS tailings requires that crushing product can’t contain too much oversize product, so the essential equipment include two crushers and one sieve in the traditional crushing system. The new crushing system which only includes two crushers can meet the requirement and simplify the crush process. Investment of crushing equipment and infrastructure can be cut down. Operating and maintenance costs can be obviously reduced due to the simple process, which also could achieve high energy saving and excellent economic efficiency.INTRODUCTIONMetallurgical Slag (MS) such as steel slag, copper slag is a typical industrial solid waste and it threatens our environment’s safe. Metallurgical enterprises must take action to settle these wastes in order to protect our environment. Because pure metal slug can easily be mixed into MS, its uniaxial compressive strength (UCS) will exceed 200Mpa. If crushing station employs traditional crushing equipment, equipment failure will be easily caused because of these pure metal slugs. Coarse crushing equipment usually adapts jaw crusher in traditional Crushing technology and rod mill will be utilized to finish the secondary and fine crushing works. And the same time screening machinery should be used to ensure the suitable particle size (Figure 1)."

Jan 1, 2016

By Jan Drzymala, Przemyslaw B. Kowalczuk

Froth flotation is widely used for upgrading of ores and other materials. Efficiency of flotation depends on many parameters, including type, chemical structure and dose of flotation reagents. Selection of a proper frother in flotation depends on the material used, necessary dose of frother and its selectivity. The selectivity of flotation can be characterized by proper separation factors and indices. In this paper separation selectivity and power of frothers were evaluated basing on separation data for a given material and frother, plotted as the recovery of the useful component in the concentrate versus the recovery of the remaining components in the tailing. Such a plot is called the Fuerstenau upgrading curve. The selectivity was defined as the location of the whole upgrading curve in relation to no and ideal separation lines, expressed on the scale from 50 (no separation) to 100% (ideal separation). In turn, the flotation power was defined as the dose of frother to reach a certain upgrading level at which recoveries of the useful and unwanted components are equal. The power and selectivity of frothers were determined for the Kupferschiefer stratiform copper ore floated in the presence of a fixed amount of xanthate and varying doses of frothers using a laboratory flotation machine. Basing on the separation results for different poly(propylene glycol) (CnH2n+1O(C3H6O)mH, CnPm) and poly(ethylene glycol) (CnH2n+1O(C2H4O)mH, CnEm) alkyl ethers, it was found that the concentrate yield and recovery of copper as the useful component in the concentrate were greatly influenced by the type and dose of frother. However, the same results plotted in the form of the Fuerstenau upgrading curve clearly indicated that the selectivity of frothers was similar, while their power was different. It proves that both selectivity and power of frothers are useful parameters for characterizing flotation systems.

Jan 1, 2016