Search Documents

By Steve Forgeron, Brendan MacKenzie, Kevin MacPherson

"The geological composition of strata immediately adjacent to coal seams has a significant effect on the safe and efficient extraction of coal from underground mines of the Sydney coalfield. Geological features such as paleo-sandstone river channels, seam splits, floor rolls, paleo-soils and stone-filled rupture features can rapidly alter the competency of immediate roof and floor strata, significantly reduce the height of the coal seam, cause rapid variations in seam gradient and influence the in situ and run-of-mine quality of the coal.The impact of these features on the over-all mining operation can be significantly reduced if mine management can be for-warned of their impending occurrence. Using the information acquired from boreholes, geological mapping, x-ray diffraction analyses, microscopic studies, geophysical logs and seismic surveys, sedimentary models have been constructed which enable the mine geologist to predict, with increasing accuracy, the future occurrence of deleterious geological features ahead of the working face."

Jan 1, 1986

By R. C. Lo, M. D. Scott

"This paper reviews tailings management at Highland Valley Copper, and outlines main features of its tailings storage facility enclosed between the H-H and L-L dams. Key management focusses are: energy efficiency, cost effectiveness, safety and integrity of the tailings impoundment, environmental protection, and reclamation after decommissioning. Main features of the tailings facility include: high international standards for seismic and flood design criteria, water management and water quality monitoring, operations and construction optimization, reclamation and decommissioning plan, and geotechnical challenges associated with the complex geology of the L-L tailings dam foundation.IntroductionHighland Valley Copper stores its tailings mainly in the Highland Valley tailings facility (ultimate capacity: 1.8 billion tonnes). Smaller tailings storage facilities were operated by predecessor companies: the Number One Pond, the Trojan Pond at Bethlehem and the Highmont Pond at the Highmont operation as well as backfilling the Heustis and Jersey lona Pits at Bethlehem. These areas are currently not in use, and are in the reclamation phase prior to decommissioning. This paper focusses on tailings management in the main facility. As indicated in Figure I, the facility includes three tailings dams: these are, going from east to west, the H-H, J-J and L-L Dam, named after the alignment alternatives in the initial feasibility studies. From 1970 to 1977 Canadian Bechtel Ltd. advised Highland Valley Copper's predecessor company Lornex, on tailings storage at the H-H and J-J Dams and on the L-L Dam. Since the completion of the L-L Starter Dam in 1977, Klohn Leonoff Ltd. has provided ongoing consultation and construction monitoring of the raising of the L-L and the H-H Dams. The J-J Dams is currently buried by deposited tailings. This paper reviews key tailings management focusses and main features of the tailings facility."

Jan 1, 1992

By R. S. Nichols

"During 1973 to 1978, Canadaka Mines Limited, a subsidiary of St. Joseph Explorations Ltd., undertook an extensive exploration and development program in the Cobalt area. This program resulted in the delineation of previously unknown stratigraphic units in the Archean volcanic sequence. During this time period, significant are controls related to area silver deposits were also identified.The Archean geology is comprised of a volcanic pile conformably overlain by sediments. The volcanics contain at least two felsic volcanic centres near the stratigraphic top of the pile. The bulk of the pile consists of mafic flows and interflow sediments. lnterflow sediments around silver are shoots contain mineralized halos of base metal sulphides. The halos exhibit lateral and vertical metal zoning with Cu, Pb and Zn mineralization decreasing away from an are shoot.Silver mineralization controls determined during the Canadaka program agree with the historically well established importance of Coleman sediments as well as Archean contacts for hosting silver deposits. The vertical extent of are shoots is typically 150to 250ft. A strong correlation was found to exist in the Cobalt area between Archean strike and the strike of are veins. Finally, al/ Cobalt area are deposits appear to be associated with a distinct volcanic pile at the top of a sequence of Archean flows."

Jan 1, 1988

By Michel David

"The usual complaint of mines is that grade does not match exploration expectations. Quite often, more tons are mined than expected but at a lower grade. This can be seen as dilution. Geostatistics can help predict which dilution can be expected both in terms of grade and tonnage for different mining methods.The usual vocabulary of geostatistics speaks of block distribution; block variance, size effect, information effect, all terms which say very little to the practitioner. In f act, all this can be rephrased in terms of dilution .In this paper, the following is presented - an example which shows how reserves change with the size of selection units and number of samples taken, and tables which show the dilution that are bound to happen when dealing with the commonly encountered log-normal distribution. Finally, the paper shows how grade tonnage computations should be made in the case of an arbitrary distribution. IntroductionGeostatistics progresses more and more rapidly if one judge s by the number and quality of papers published in Mathematical Geology or at APCOM meetings. More and more case studies describing successful applications are published (David et al., 1986)(Kwa and Mousset-Jones, 1987). It is estimated that more than 270/0 of the gold mines around the world use geostatistics. There is still, however, a lot of resistance from the remaining 73%. Geostatistics has more formulae and equations than it needs to reach year 2000. We will be well into the third millenium before all the models available now are actually used. The progress may come in the form of finding better ways to present known statistical results and getting away from the jargon of geostatisticians. One example may be in trying to explain how we can answer the most common plea of the mining industry: production grade is not what was expected in the feasibility study."

Jan 1, 1988

The mixer that is commonly encountered in hydro metallurgical operations consists of a single turbine and tank combination. However, it would be advantageous to examine some common solvent extraction mixing systems in the light of the fundamentals of chemical reactor design. The basic concepts of reactor design are commonly used in the chemical industry, and it should not be too difficult to apply them to solvent extraction. The factors that affect the engineering design of a reactor are: the reacting system; the type of reaction; and the configuration of the reactor. The reaction system in solvent extraction consists of a heterogeneous liquid phase, involving two immiscible liquids. It is essential f or the process that the reactor product can be separated efficiently in the subsequent settler. The type of reaction in solvent extraction system may be quite complex, and the picture is complicated by the presence of competing and side reactions. The reactors themselves have been generally continuous stirred tanks, and the nature of the mixer-settler makes it unlikely that the pumping mixer can be dispensed with. However, it appears that there should be some definite advantages to a system of stirred reactors in series. The kinetic experiments which are carried out should have the definition of optimum reaction conditions as one of their goals. The data obtained from these experiments must also be applicable to the design of reaction equipment. Reactor selection and design is often a unique problem for each chemical process, and does not lend itself to a systematic general approach. However, the application of chemical and physical principles to mixer design in solvent extraction should result in practical, more efficient plants.

Jan 1, 1979

By G. J. Reid, D. H. Stewart

"A diversity of structures and rock types in the Aft on pit has resulted in the occurrence of several different types of wall failure. Delivery of ore to the mill has not been affected and safety has not been compromised thanks to effective remedial 1V0rk and to a system of structural mapping, back analyses of failures, groundwater monitoring, and simple movement monitoring. Remedial measures have included artificial support, dewatering (including vacuum-assisted drainage), flattening of slopes and temporary buttressing. This paper describes six different wall failures at Afton and highlights the features of each. Examples given include rates of movement, extent and direction of movement, and piezometric responses. The practical, low-cost monitoring system was sufficient in one case to allow the prediction of date of failure. IntroductionThe Afton copper deposit is located 13 km west of Karnloops, British Columbia and has been mined for nine years out o f an expected eleven-year life. Open pit mining has reached 700 feet below sur face and is designed to proceed to 970 feet below surface by the time the pit is completed. The excavation is in a structurally and lithologically complex environment. Inevitably, some wall failures have occurred but these have been limited to small, manageable failures which have not compromised production or safety. To handle the failures it has been necessary to understand their nature. Of prim e concern has been the rate s of movement, but displacement vectors and hydrology have been monitored as well. The monitoring system is based on EDM surveys and on wire extensometers and plates set across cracks. Water levels have been read in standpipe piezometers. At Afton the emphasis has been on simple, practical, and inexpensive monitoring and because rock type s and structures play such a major role in any failure, detailed geologic al mapping is carried out."

Jan 1, 1988

By L. Dekker

"In 1979 Chevron Standard Limited and Irving Oil Limited intersected a thick, high-grade sylvinite zone in the Windsor Group in the Chevron Irving Malagawatch No. I well in central Cape Breton. This well was the third and final hole of a program designed to evaluate a non-commercial oil discovery made by Chevron Standard's Mineral Staff in 1978 while carrying out base metal exploration. Nine holes were subsequently drilled to evaluate the significance of the potash discovery. The delineation drilling proved the Malagawatch structure to be complex with the potash zone showing erratic grade and thickness distribution. Based on the drill information the potash accumulation at Malagawatch is uneconomic, however, other salt ""structures"" in the Bras d'Or Basin may in time prove to have better potential.History of DiscoveryIn 1972 Cuvier Mines discovered the Gays River lead-zinc deposit (MacEachern and Hannon, 1974) which prompted Chevron Standard's Minerals Staff to carry out a study of the Windsor basins in Nova Scotia (Figs. I and 2). As a result of this program several carbonate-hosted lead-zinc prospects were identified in the basal Windsor carbonate; one of these was at Malagawatch on Cape Breton Island . In 1978, after preliminary exploration surveys, a diamond drill program commenced consisting of 5 BQ holes (Fig. 3), three of which tested the basal carbonate. Instead of the reefoid bank facies of the Gays River Formation (Giles et al., 1979), the favoured host for economic base metal mineralization, this carbonate was developed as a laminated, pelletoidal, lime packstone more characteristic of the facies equivalent Macumber Formation (Schenk, 1967). While drilling one of these holes, No. 3-78, oil scum was intermittently detected on the drilling mud. The hole was abandoned at 191 m in anhydrite, without having reached the basal limestone."

Jan 1, 1985

By Lynn C. Fister

"Coal is rapidly becoming a major alternative to oil. According to the World Coal Study Final Report, total world coal trade could approach one billion tons annually by the year 2000. To facilitate the increased production and export market potential of the coal producing countries, advancements must be made to improve the transportation systems. Coal slurry pipeline systems could play a significant role in achieving these market forecasts.There are three major components to a coal slurry system the preparation plant, the pipeline and the dewatering plant. The experience and expertise gained from the Consolidation Coal Company system in Ohio, the Black Mesa system in Arizona and ETSI's Coal Evaluation Plant demonstrate that slurry pipeline technology is proven and available to meet the coal transport challenge.The costs of transporting coal by slurry pipeline can offer significant savings, as about 70 per cent of its costs are fixed. The reverse is true for railroads, where 75 to 80 per cent of the costs vary with inflation. All forms of transport-rail, barge and pipeline-will be required to move the massive volumes of coal. Coal slurry systems can provide a viable transport alternative.IntroductionThe importance of coal as a major alternative to oil is now well known and accepted throughout the world. Increasing oil prices over the last eight years have had a serious effect on national economics, particularly in those countries that are heavily dependent on oil. Coal can replace oil as the principal fuel source which could support world economic growth over the next two decades. This is the main conclusion of the World Coal Study (WOCOL) Final Report, published in May 1980.The product of that report was a result of considerable deliberation by key industry leader s and energy experts. The underlying message of the World Coal Study is that our energy and economic problems can be faced with confidence if coal use doubles by the early 1990s and triples by 2000, and if steam coal trade expand s considerably."

Jan 1, 1982

By G. B. Hobbs, S. Saimoto, L. Collins

"Plastic yielding and flow in metals is dependent on the microscopic process of simple shear along crystallographic planes and directions known as slip. Thus, by altering the crystallographic direction of the stress axis or placing constraints in the direction of plastic flow, anisotropy of yield strength for the same material is observed. This phenomenon is called texture strengthening. The application of this concept to highly anisotropic crystal structures such as the hexagonal group of titanium and zirconium alloys, the former in missile casing and the latter in nuclear reactor fuel tubing, seems obvious. The outstanding example in cubic structures is the case of deep-drawing steel. The R value, the width strain over the thickness strain during a tensile test, is taken as a measure of texture strengthening. In face-centred cubic structures, texture strengthening has been completely ignored on the basis that materials with R less than one are not amenable to this beneficiation. This study will review two aspects of texture which will lead to strengthening, first the thermal stability of the deformed microstructure, which is dependent on the stress axis, and second, the texture strengthening aspect of fcc metals.A review of recovery and recrystallization in textured aluminum wires, copper and cupro-nickel sheet will be presented with the view of extending these concepts to the manufacture of heat-exchanger tubing. The superior creep properties of specially processed commercial products such as TD-Ni, TD-NiCr and MAR-M200 will be shown to be a manifestation of the same physical phenomena."

Jan 1, 1981

By P. J. Urso

"This paper discusses the mining problems encountered at the Fording River coal mine to date, and how they have been solved. All of the production now comes from surface mining, but underground hydraulic mining is planned and briefly described. Other facets of the operation, including markets, equipment and personnel, are covered. IntroductionFording Coal Limited was formed in 1968 to mine and market metallurgical coal resources held by the company in the East Kootenay region of southeastern British Columbia. The company, at its Fording River operations, holds approximately 48,000 acres of coal lands, having an estimated 2.0 to 3.0 billion long tons of metallurgical coal in place. (Although not a point for further discuss ion in this paper, the company also holds approximately 1.0 million acres of mineral rights. These consist primarily of coal in Alberta, potash and coal in Saskatchewan, and minor industrial mineral holdings of limestone, salt and bentonite in the three western provinces.)Fording Coal is owned 60% by Canadian Pacific Investments Ltd. and 40% by Cominco Ltd. Inasmuch as Cominco itself is owned approximately 54% by CPI, it is seen that the effective CPI ownership of Fording is about 82%. The company, originally staffed and managed by Cominco, has been independent since January, 1978, with its own board of directors, management, staff and employees.The company's head office is in Calgary, Alberta. The Fording River operations are located approximately 45 miles north of the Crowsnest Pass, near the Alberta/British Columbia boundary, only 95 air miles and 200 road miles from Calgary.A contract was signed in 1969 with the Japanese steel mills to provide 45 million long tons of metallurgical coal over IS years, commencing in 1972 at an annual rate of 3 million long tons per year. Despite some start- up difficulties, the mine and plant facilities achieved their rated capacities in 1975, producing and shipping at the 3-million-Iong-ton level. The coal specifications are shown in Table I."

Jan 1, 1980

By R. A. Walker, G. Scheltgen, T. Javorsky, G. Blackwell

"Recent engineering advances in open pit rock mechanics have resulted in improved pit wall slope design and improved operating procedures in the event of a major wall instability. At the other end of the spectrum, on the scale of single bench failures, considerable discretion is left to the mine operators as to how potential problems are handled. The usual alternatives are either to operate with caution beneath potential hazards, or try to bring the unstable rock down. In specific cases it may be advantageous to attempt to stabilize rock structures for reasons of access and operating safety.A t the Brenda Mines open pit a prominent structure on the north wall had caused recurring bench-scale wedge failures when exposed on each mining level. In spite of operating precautions a shovel was hit by a rockfall causing significant damage. The first section of this paper describes the investigative, design, and stabilization methods which permitted subsequent mining beneath the structure to proceed without incident. Emphasis is placed on the personnel and equipment resources available at the mine site which were used to minimize costs and which would be available at most operating mines.The second section describes an ongoing research project that utilizes radio telemetry to transmit slope monitoring data. As part of this project the wedge structure was instrumented so that it could be continuously monitored with the aid of a computer. The application demonstrated the potential of 'micro- chip' technology to remote data collection and processing as related to rock structure monitoring, slope stability and safety."

Jan 1, 1989

By S. Perkins, E. Young, L. Dufour, K. McVey, L. Rolandi

This paper presents a review of plant layout considerations incorporated into recent designs of SAG/Ball mill circuits for two medium sized concentrators. The plant layouts presented and the design concepts discussed, relate to smaller SAG circuits, but can equally apply to larger milling circuits. Included are design concepts and ideas introduced by the various project teams, and the focus is on the primary factors of any layout design which are safety, constructability, operability, and capital cost.

Jan 1, 2012

By P. Mottahed, E. K. S. Passaris, J. Q. Ran

"The jointed roof of underground mine openings in stratified rock can be analyzed in terms of a voussoir beam. Because of the essential indeterminacy of the structure, previous attempts of theoretically solving the equilibrium equation have been unsuccessful. Numericalanalysisby the finite element method taking the geometrical and joint non-linearity into consideration combined with the experimental method has been adopted to study the performance isopara of the voussoir beam. Deformation and failure mechanism is analyzed in relation to the failure modes. Equations are proposed to estimate the elastic buckling strength and the crushing strength of the voussoir beam and to verify the failure mode of shear sliding. For application of the mechanism of the voussoir beam in mining operations, methods are described to predict the stability of a jointed roof and to design the dimensions of mining openings.IntroductionThe roof stability of an underground mine opening has direct effects on the selection of support methods, opening dimensions and, more importantly, on the safety of mining personnel. The prediction of the roof stability can be of importance in the design of a mining method and in mining operations. The jointed roof of mine openings in stratified rock can be stable under transverse load depending on the roof geometry and properties of the roof material and joints. The stability of this type of roof can be analyzed in terms of a voussoir beam which was introduced by Evans (1941) to study the strength of underground strata. Brady and Brown (1985) analyzed the voussoir beam and suggested that the mechanism of the voussoir beam could be used in the design of underground mine openings in stratified rock instead of the traditional continuous beam theory."

Jan 1, 1993

By J. Spross

"The Key Lake mill has operated since the fall of 1983. The ore from both Key Lake open pits will be depleted by 1997. It is planned to use this mill, located about 60 km southwest of McArthur, to process the McArthur River ore.While the geological data collected so far on the McArthur deposit are encouraging, more information of the deposit is needed before any detailed mine planning can begin.The surface drilling program identified the orebody and provided information on the geomechanical and hydrological properties of the overlying sandstone. It was proposed to conduct an underground exploration program to further delineate the orebody. This was air proved following a public hearing and review process. This program involves the sinking of a 630 metre deep shaft and the driving of one or two drifts along a portion of the orebody. From these drifts, exploration drilling every 10 m to 15 m through the orebody will provide the information required for the preparation of a feasibility study and an Environmental Impact Statement (EIS)."

Jan 1, 1994

By L. A. Homeniuk, R. Bonnar

"The Fond-du-Lac uranium deposit is located on the northern rim of the Athabasca Basin. The uranium mineralization is, for the most part, confined to the Athabasca Group, which is underlain by pre-Helikian metamorphic rocks of the Western Craton.The deposit is characterized by a remarkable train of mineralized glacial erratics which led to the original discovery. The mineralization is present as a ""high-grade"" core and a diffuse ""low-grade"" aureole. The ""high-grade"" core occurs as a stockwork of steeply dipping pitchblende veins which strike N 50°E. Hematite, siderite and secondary silicate are also abundant. The ""low-grade"" aureole contains uraniferous goethite, argillaceous material and rare carbon buttons. Recent alteration to coffinite has taken place along the margins of pre-existing ore minerals.The ""high-grade"" core is 390 m long and 10 to 40 m wide, and is surrounded by an irregularly shaped zone of ""low-grade"" mineralization with a similar length and a width of up to 350 m.Comparing the Fond-du-Lac deposit to other unconformity-type deposits, several important differences can be noted:1. Ninety per cent of the ore is above the unconformity, in the Athabasca sandstone.2. The deposit is not associated with underlying graphitic rocks or a major structure.3. The clay-rich alteration zone is not extensive around the Fond-du-Lac deposit.Although there are differences with other Athabasca unconformity-type deposits, the high-grade portion below the unconformity suggests a common origin.The ore deposit is postulated to have been formed from uranium-bearing solutions which entered the stockwork of fractures. Following the reduction in part of these solutions by pre-existing carbonaceous matter and pyrite and/or chemical reaction with pre-existing hematite, deposition continued as a result of decreasing temperature and pressure. Subsequently, minor supergene redistribution of the uranium has taken place."

Jan 1, 1982

By L. A. Homeniuk, R. Bonnar

"The Fond-du-Lac uranium deposit is located on the northern rim of the Athabasca Basin. The uranium mineralization is, for the most part, confined to the Athabasca Group, which is underlain by pre-Helikian metamorphic rocks of the Western Craton.The deposit is characterized by a remarkable train of mineralized glacial erratics which led to the original discovery. The mineralization is present as a ""high-grade"" core and a diffuse ""low-grade"" aureole. The ""high-grade"" core occurs as a stockwork of steeply dipping pitchblende veins which strike N 50°E. Hematite, siderite and secondary silicate are also abundant. The ""low-grade"" aureole contains uraniferous goethite, argillaceous material and rare carbon buttons. Recent alteration to coffinite has taken place along the margins of pre-existing ore minerals.The ""high-grade"" core is 390 m long and 10 to 40 m wide, and is surrounded by an irregularly shaped zone of ""low-grade"" mineralization with a similar length and a width of up to 350 m.Comparing the Fond-du-Lac deposit to other unconformity-type deposits, several important differences can be noted:1. Ninety per cent of the ore is above the unconformity, in the Athabasca sandstone.2. The deposit is not associated with underlying graphitic rocks or a major structure.3. The clay-rich alteration zone is not extensive around the Fond-du-Lac deposit.Although there are differences with other Athabasca unconformity-type deposits, the high-grade portion below the unconformity suggests a common origin.The ore deposit is postulated to have been formed from uranium-bearing solutions which entered the stockwork of fractures. Following the reduction in part of these solutions by pre-existing carbonaceous matter and pyrite and/or chemical reaction with pre-existing hematite, deposition continued as a result of decreasing temperature and pressure. Subsequently, minor supergene redistribution of the uranium has taken place."

Jan 1, 1982

By M. P. Brameld, R. H. McCorkell

"Overburden covering bedrock uranium deposits was sampled to depths of 29 m and Rn concentrations measured at the same depths. Total-alpha activities, V concentrations and Rn emanation (J) of the samples were measured. The U-flux into the overburden was greater in the past: oxidation and dissolution has since removed most U, leaving decay products which indicate the presence of U deposits when U itself does not. Distributions of U and decay products and their ratios to each other reflect U-migration and degrees of U-removal. Rn distribution in overburden is related to the J of overburden samples and the presence and movement of groundwater. Simple, rapid methods of total-alpha and J measurement are described.IntroductionThe overburden drilling apparatus developed by Bondar-Clegg and Company makes possible sampling and radon measurement in overburden from the surface down to about 50 metres. This apparatus was used here to study the diffusion of uranium and its decay products from ore deposits into over lying overburden at the N deposit of the Amok Ltd. property (Cluff Lake, Saskatchewan) and on the Imperial Minerals Ltd. property at Gooderham, Ontario. These ores are enclosed in bedrock; the overburdens were deposited by glaciers or streams. The migration of uranium and its decay products in such situations and the factors which affect it have been little studied in the past, as readily usable techniques for mapping it in three dimensions have not been available. The results reported here are somewhat sketchy and preliminary, but they indicate the value of the methods used and some of the patterns to be expected. Surface and subsurface sampling and measurements were carried out on 3-line grids crossing known zones of mineralization. The lines were 60 metres apart at Gooderham and 40 metres apart at Cluff Lake."

Jan 1, 1982

By Ward E. Kilby, Bruce I. Mcclymont

"Data from the South Fork Pit Area of the Bullmoose deposit in northeastern British Columbia are used to demonstrate the usefulness of microcomputers to the on-site geologist. The technique utilizes a series of digital surf aces in the form of a network of points to define various geologic parameters such as seam positions, topography and coal quality characteristics. Manual digitizing, kriging and combinations of these techniques are used to calculate these digital surfaces, the best method depending upon the type and quality of the data in question. Digital surfaces, each modelling a specific feature when combined and manipulated with the computer form a powerful tool, the deposit model. The resultant model, containing all the surfaces, is used to examine seam and inter-seam thicknesses, deposit volumetrics, seam quality characteristics and the adequacy of sampling.IntroductionCoal deposit modelling using computer-based techniques has become routine. However, a geologist working in the field, without access to mainframe or minicomputer, ha s considerable difficulty implementing these procedures. However, microcomputers, which are portable and inexpensive can handle exploration data, perform various geological analyses, and produce deposit models virtually at the same time as the data is being collected. For the on-site geologist this means that quick access to the results of such modelling could point out inadequacies in deposit definition and trends in coal quality deserving investigation."

Jan 1, 1985

By D. R. Spink, G. L. Rempel, C. O. Gomez Bueno

"A morphological and chemical study of the Great Canadian Oil Sands Ltd. (GCOS) fly ash has been carried out. Extensive scanning electron microscopy, as well as light microscopy, showed that the GCOS fly ash consists of two fractions, one composed of unburnt or partially burnt irregular-shaped carbon particles and an ash fraction composed of transparent and opaque, often coloured, glassy spherical particles-some of them cenospheres (hollow spheres) and the others plerospheres (hollow spheres packed with smaller spheres). Microcrystals (0.1 to 0.3 um long) growing on the inner and outer surfaces of some of the spheres were also noted and found to contain more Fe, Ti, Ni and V than the spheres.The carbon-free GCOS fly ash particle size follows a lognormal distribution, with a geometric median particle size (by count) of3.8um and a geometric standard deviation of 1.84. IntroductionCanada's current energy situation strongly suggests that oil from the Alberta tar sands deposits will probably be recovered more extensively in the future. Today's commercially proven technology to recover oil from the Athabasca tar sands, as practised by Great Canadian Oil Sands Ltd. (GCOS), involves two major operations, namely: separation of the bitumen from the sand and upgrading of the bitumen to refinery oil; the production of significant amounts of petroleum coke and sulphur during the bitumen upgrading process. The bulk of the petroleum coke is burnt in boilers to fulfill the energy requirements of the entire operation. The boiler ash, which contains appreciable amounts of metals, such as vanadium, nickel, titanium, iron, aluminum and other elements, is collected in the boiler hoppers and cyclones of the petroleum coke-fired steam generation plants. Thus, as well as representing a petroleum resource, the tar sands represent a resource for vanadium and possibly other metals providing that metal recovery processes can be developed."

Jan 1, 1980

By G. P. Demopoulos

"The recovery and separation of platinum-group metals (PGM) from primary and secondary materials currently attracts a lot of interest due to the high value of the metals and their increasing demand for high-tech applications. Thus, the traditional refining processes are gradually replaced by newer more efficient separation techniques such as solvent extraction and ion exchange. In this paper the classical and modern refining techniques are reviewed and the pertinent solution chemistry dictating proper processing strategies in each case is discussed. The technological advantages of the modern separation methods are emphasized and reference to the recovery of PGM from primary as well as secondary materials is given. INTRODUCTIONDue to their outstanding physicochemical properties, such as catalytic activity, conductivity and corrosion/oxidation resistance, precious metals now find extensive usage outside of the traditional jewellery and investment industries. The increasing use of precious metals in such areas as electronics and catalysis, as well as their increasing high value, has led to a growing interest in their recovery and separation from primary and secondary materials.Quantitatively the demand of platinum metals in the western world by area of application is described in Table I. Platinum and palladium represent 90% of the total demand, Rh and Ru 8% and the remaining is taken by Ir and Os. In terms of value the following were the average prices (US$/oz) of the metals in the second half of 1986: 500 Pt, 125 Pd, 1200 Rh, 650 Os, 400 Ir and 80 Ru. Due to these prices, exploration, mining, reclamation and refining activity were very high in South Africa, the biggest producer of Pt metals in the world, as well as in other areas: United States (Stilwater deposit), Canada (Sudbury, Marathon and Lac des Isles, Ontario; Kenly Lake, Quebec, etc.), Australia, Europe and elsewhere"

Jan 1, 1989