Search Documents

By M. X. Yao, C. D. Opris, P. C. Patnaik, R. Liu, X. J. Wu

Two cobalt-based superalloys, Stellite 694 and Stellite 712, were functionally graded with reinforcement of titanium-carbide particle for high-temperature wear/corrosion applications. The designed composite specimens were fabricated using powder metallurgy (P/M) technique, combined with hot isostatic pressing (HIP). Calorimetric effects of the alloy powders were investigated using the differential scanning calorimetry (DSC) technique, which provided the basis of the sintering cycles designed. The phases present in the microstructures of the materials were analyzed using SEM and X-ray diffraction. The wear resistance of the materials was evaluated on a pin-on-disc tribometer. It was demonstrated that adding titanium-carbide particles to the alloys has increased significantly their wear resistance. It was also found that the HIP process had improved the density of the sintered specimens and thus enhanced their wear resistance.

Jan 1, 2004

By Paul D. Young, Michael J. Allan

"The Con Mine has been producing gold continuously since 1938. In 1990 laboratory and pilot plant investigations began into the use of pressure oxidation for treatment of an arsenic trioxide waste product from two previous roaster operations on the property. This led to the construction in 1992 of a 96 ton/day plant to treat a mixture of arsenic waste and flotation concentrate from the existing mill. The plant was commissioned in the fall of 1992.This paper describes experience gained in the commissioning and initial operation of the plant. The unique aspects of treating a hazardous waste product are described including special operating procedures to satisfy environmental and employee safety concerns. The paper further describes modifications made to the process flowsheet, to operating procedures and to materials of construction in the early months of operation."

Jan 1, 1994

By J. L. Rodrigues Bravo

The aim of this paper is to show the results of the study that relate the variations of the bismuth content in the Caraíba Metais' electrolytic copper with the main electrolysis' process variables as electrolyte flow rate and temperature, anode's impurities content, electrolyte composition, current density, etc and their combinations and factors like cathode washing, blend of materials entering rod plant's furnace, analytical methods, shot-circuit inspection, etc. Also, the methodology considered arsenic, bismuth and antimony mass balance in the electrolysis and their electrolyte's molar ratio relations as well as bibliographic references of refineries that operate in similar conditions. The results showed the circumstances with the major probability of causing bismuth content increasing in the electrolytic copper and the main operating conditions that have to be fixed for having less bismuth variation and lower content in the electrolytic copper.

Jan 1, 2007

By F. Golestani-Fard, A. A. Nourbakhsh

In this paper microstructural development of nitride-Bonded SIC refractories is reported in presence of Al203, Mg() and Urea additives .The samples were prepared by mixing, shaping and firing at 1400-1500°c in a controlled atmosphere furnace. Phase analysis, microscopic observation and mechanical evaluation were taken for microstructural investigations. The strength of samples doped with Al203 was first increased and then decreased at higher amount of Al2O3 additions. The addition of MgO decreased the strength while the urea showed an improving effect on strength. These phenomena could be attributed to microstructural evolution and mainly to liquid phase formation and grain morphology. It was found that the additives such as Al203, MO and urea could modify the microstructure in terms of phase formation and texture modification, which in terms influences the mechanical behavior.

Jan 1, 2004

By Fengxiang He, T. Meadowcroft, Yanjun Zhang

Slag from the zinc fuming furnaces contains about 3 percent zinc and 0.1 percent lead. The paper outlines several experimental techniques for recovering these components from liquid fumer slag. The simplest method, remelting followed by a hold period, indicated that a substantial fraction of the metal values was recoverable as a result of fuming into the gas phase, presumable by reduction of the metal ions by divalent iron ions. Following on from this, slag samples were equilibrated with copper, chosen because the activity coefficients of zinc and lead in copper are very low. This improved metal recovery, with substantial amounts of lead and zinc reporting to the liquid copper as well as to the fume. Application of an electrical emf across the slag-metal interface, using a graphite anode and a liquid copper cathode, resulted in further gains in metal recovery.

Jan 1, 2004

By M. S. Moats

As smelter feeds become more complex, the impurities that ultimately report to electrorefineries are changing. Many of these impurities collect in the electrolyte and must be controlled. As commercial copper electrorefineries look to expand their capacities by increasing their operating current density, the interaction between electrolyte composition and anode passivation can cause operational difficulties. To improve the industry's understanding of the passivation phenomena, the role of electrolyte composition was evaluated using commercial electrorefining anode samples. The electrolyte composition variables examined were copper, acid, nickel, arsenic, chloride, thiourea and glue. Finally, the role of non-commercially utilized additives, such as bromide and polyethylene glycol were studied. From this investigation, electrolyte parameters that inhibit copper dissolution through copper sulfate precipitation, copper oxide stabilization and/or absorbed species lead to accelerated passivation. Species that prevent passivation have the ability to complex cuprous ions. Possible mechanisms for the role of each.

Jan 1, 2007

By T. Cutard, E. Cailleux, F. Nazaret, G. Bernhart

This paper deals with the study of the mechanical behavior in the 20°C-900°C temperature range of refractory concretes reinforced with metallic fibers. Fibers are introduced to improve the damage resistance and to minimize the quasi-brittle behavior of refractory concretes. In some cases, a plastic or ductile like behavior can be obtained. Two approaches are considered in these studies. The first one is based on the micromechanical scale. Main objectives are to understand, quantify and predict the thermomechanical behavior of monofiber microcomposites. Such considerations are helpful to optimize the composite formulation for a better behavior. The second one is based on the macromechanical scale. Main objectives are to characterize and to model the macroscopic thermomechanical behavior of randomly reinforced refractory concretes. A particular attention is firstly paid to the relationships between the microstructural changes and the mechanical properties and secondly to the structural size effects.

Jan 1, 2004

By S. R. Izatt

The use of MRT, a highly selective separations technology, has long been demonstrated to be a cost effective, efficient, and environmentally sound process for extraction of a wide range of anions and cations that are commonly found in copper electro - refining and electro - winning circuits, as well as in environmental treatment operations. This paper provides an update of commercial MRT applications in the copper industry. Several recent installations and test programs are reviewed including recovery of bismuth from tank house electrolyte, and from chloride matrix selenium reduction solution which is generated in the anode slimes treatment process. Recovery and refining of platinum group metals originating in the anode slimes is also discussed. Various other base metal and other target separations of interest to the copper producer are also reviewed. The recovery products are high purity metal salts which can be marketed directly or readily reduced to metal.

Jan 1, 2007

By T. Hartmann

The presence of crud represents a permanent challenge for solvent extraction in the hydro-metal industry. The crud is a stable emulsion which slowly spreads along the phase boundary between the aqueous and organic phase. The crud can significantly impair the efficiency of hydro-metal extraction because the phase boundary between the aqueous and organic phases assumes substantial proportions, and the settlers cannot react flexibly. In a chain reaction, all settlers connected in series become infected with crud. The transfer of organic phase to the electrowining (EW) cell can cause 'cathode burn'. Continuous treatment of the crud is extremely effective and reliable with a 3-phase separating solid bowl centrifuge. All three phases are separated distinctly from one another. All associated process steps exhibit a steady uniform efficiency. First and foremost, they ensure a reliable, continuous extraction process and, second, they recover valuable re-usable organics from the crud.

Jan 1, 2007

By Jorge Amaya

A critical aspect of long-term open-pit mine planning consists in computing a production schedule based upon a block sequencing strategy. Such a schedule should specify when and if blocks should be extracted in such a way as to maximize NPV, while satisfying wall-slope and production capacity constraints. It is well known that this problem can be modeled with integer programming (IP). However, integer programming is not used in practice because the size of typical block models makes such problems intractable to standard IP solvers. In this article we describe a scalable IP-based methodology for solving very large (millions of blocks) instances of this problem. We show that embedding standard IP technologies in a local-search based algorithm we are able to obtain near-optimal solutions to large problems in reasonable time. This methodology has been tested in several mine wide block models.

Oct 1, 2009

By Jorge Amaya

A critical aspect of long-term open-pit mine planning consists in computing a production schedule based upon a block sequencing strategy. Such a schedule should specify when and if blocks should be extracted in such a way as to maximize NPV, while satisfying wall-slope and production capacity constraints. It is well known that this problem can be modeled with integer programming (IP). However, integer programming is not used in practice because the size of typical block models makes such problems intractable to standard IP solvers. In this article we describe a scalable IP-based methodology for solving very large (millions of blocks) instances of this problem. We show that embedding standard IP technologies in a local-search based algorithm we are able to obtain near-optimal solutions to large problems in reasonable time. This methodology has been tested in several mine wide block models.

Oct 1, 2009

By Michel Aubertin

Mining activities can produce large volumes of waste rock, which are typically deposited in piles on the soil surface, above the water table. Such piles can cover areas of several tens of hectares and can reach over a hundred meters in height. For hard rock mines, the waste rock grain size can vary from silty particles to metre-scale blocks. The internal structure of a pile constructed on a relatively flat surface typically includes two main zones. The first zone corresponds to the heart of the pile, and is formed by several sub-horizontal stratifications (with dense and loose layers) due to the heavy mine equipment traffic which induces local compaction and degradation of the waste rock. The second zone corresponds to regions where waste rocks are deposited by push-dumping or end-dumping close to the external flank of the pile, inducing grain size segregation along the slope. Depending on the deposition sequence, grain size distribution and bench height, a gradation may then be observed, with coarser particles (with cobbles and blocks) near the base and finer particles near the crest, together with inclined stratifications due to the advance of the deposition face. These internal features affect the distribution and flow of water (and air) in the pile. To assess the internal distribution of material properties within the pile, a combination of several tools is usually required which can provide information on the hydrogeological and geochemical characteristics of the waste rock. In this regard, geophysical tools are very interesting because they can lead to a threedimensional mapping of property variations. The information gathered from a combination of appropriately selected techniques can be used to construct numerical models to further study unsaturated water flow and reactive transport. Such simulations help better understand the pile response in its actual and future states, which in turn provides input to adjust the deposition sequence, to plan for closure, and to select an in situ groundwater monitoring strategy. The presentation will give an overview of techniques that have been developed to characterise material properties in the laboratory and in the field, and to obtain a general picture of a pile?s internal structure. Additional results on unsaturated reactive transport modelling will also be shown to illustrate how the internal pile structure may influence its hydro-geochemical and environmental response.

Nov 1, 2008

By G. Portillo

Electrospark Deposition (ESD) is a pulsed-arc micro-welding process characterized by using high current electrical pulses, of a short duration, to deposit an electrode material on a metallic substrate. The short duration of the electrical pulse allows for a low heat input over the substrate and an extremely rapid solidification of the deposited material. As a result, the ESD is capable of a wide variety of microstructures like micro-segregationfree solid solutions, nanostructured grains, metastable structures, and amorphous phases. The present work shows a microstructural analysis of rapidly solidified Al-Ni alloys coatings by the ESD process. Field Emission Scanning Electron Microscopy (FE-SEM) and X-Ray Diffraction (XRD) were performed to present the microstructural evolution as a function of the welding parameters. The phases and non-equilibrium metastable structures present in the alloys, and their distribution, were found to be a sensitive function of the alloy composition; hence its formation is governed primarily by thermodynamic considerations.

Jan 1, 2011

By J. M. Menacho

As usually occurs in technological development, heap leaching knowledge has been built upon two parallel lanes, theory developed on fundamentals but relatively far from industrial applications, and operational know-how generated from empirical trial and error. As a contribution to close the gap between the above-mentioned lanes, the De Re Metallica process consulting group has been developing and applying fundamentalsbased modeling tools for industrial process design and process optimization of existing plants over the last ten years. As result, a library of models is now available with application to the whole production chain from blasting to electro winning. This presentation is centered in heap leaching and several real case studies are developed, showing how paradigms are broken when fundamentals are applied. Cu2007 - Volume IV (Book 1) The John E. Dutrizac International Symposium on Copper Hydrometallurgy Edited by P.A. Riveros, D.G. Dixon, D.B. Dreisinger, M.J. Collins Toronto, Canada,

Jan 1, 2007

By J. M. Shneerson

Gipronickel Institute, Saint-Petersburg will The copper concentrate was extracted from copper and nickel matte after its hydrometallurgical treatment and nickel removal. The concentrate containing 60-74% of copper was represented by two principal copper minerals, digenite and covellite. The oxidising leaching of this kind of concentrate was studied at the Gipronickel Institute. The effect of key parameters, such as temperature, oxygen partial pressure and initial solution compound, on the rate of copper dissolution and transfer of sulphur from sulphide to elemental form was investigated. It was shown that at temperatures about 90DC, the sulphur content of covellite converts to elemental form. Under autoclave conditions at 11ODC, the elemental sulphur dissolves as a sulphate-ion. At the temperature range from 50 to 90DC, the copper dissolution rate is in direct relation with temperature. By increasing the temperature to 130DC, this effect is reversed. Based on the research work, a technological flow sheet for the leaching of the copper concentrate was developed.

Jan 1, 2007

By A. Jain

During sheet forming, metal experiences not only multi-axial load, it also undergoes strain path changes. For example, metal in the flange region may be drawn, may bend and unbend through a bead, before bending around a die radius, etc. Compression data were obtained from AZ31 sheet after pre-straining in compression along an orthogonal direction. The compression directions correspond to the sheet product (rolling-RD, transverse-TD, and normal-ND) directions. Three cases are examined: slip dominated deformation (ND) followed by twin dominated (RD or TD) deformation, twin dominated (RD or TD) followed by de-twinning (ND), and twin dominated (e.g. RD) followed by cross-twinning or secondary twinning (e.g. TD). Slip induced pre-straining simply hardens the material, while twin dominated pre-straining alters the texture allowing the material to either de-twin or re-twin upon changing the strain path. Polycrystal plasticity modeling has been used to predict qualitative features of the flow curves during strain path changes.

Jan 1, 2006

By T. Watanabe, M. Nakagawa, K. Kimapong

Ultrasonic wave was irradiated on metal surface in water to introduce compressive residual stress. The ultrasonic wave that was oscillated with 19.5 kHz ultrasonic transducer and amplified with a step type horn was irradiated. Slight plastic deformation occurred at the surface region of pure metal such as Cu and compressive residual stress was introduced. It seemed that the plastically deformed depth from the metal surface corresponded approximately to the depth of introduced residual stress. The higher compressive residual stress could be introduced into the surface of Cu-Zn brass and SUS304 stainless steel because work-hardening was simultaneously induced to those alloys. Furthermore, since martensitic transformation was induced by the plastic deformation in the case of SUS304, the compressive residual stress could be introduced more deeply into the surface region. The residual stress of SUS304 reached to the maximum value of 574 MPa by irradiating for 5min.

Jan 1, 2004

By G. T. Fisher

A continuous process is used at Phelps Dodge Sierrita Inc. to produce copper sulfate pentahydrate via a solution extraction ? crystallization approach to supply the animal feed market. A review of the fundamental concepts of the process and unit operations is presented. Improvements in the process are aimed at achieving a controlled size distribution of product crystals (-40+80 mesh) with minimization of fines by primary nucleation and crystal breakage. An independent temperature control design was implemented for the heat transfer medium (water) in each crystallizer, albeit using common headers in and out of the chiller. This design was developed to maintain a controlled degree of supersaturation in each vessel while preventing localized spontaneous nucleation of fines and reducing encrustation of the heat transfer surfaces in each crystallizer. A model was developed to calculate the heat load and heat transfer coefficient of each crystallizer along with the saturation copper tenor as a function of temperature and free acid.

Jan 1, 2007

By G. Kordosky

Leaching aids that result in an increase in leaching rates and overall copper recovery have the potential to be beneficial to copper leach/solvent extraction/electrowinning operations. It is generally accepted that effective leaching aids facilitate the penetration of leach solution into ore by lowering the surface tension of the leach solution. Surfactants are designed to do this, and a leaching aid containing the widely used surfactant class, alkyl phenol ethoxylates, has been suggested. Alkyl phenol ethoxylates were tested to determine how they may affect phase separation, entrainment and degradation in a copper solvent extraction plant. The test results suggest the use of leaching aids at a regular rate, or even for a short time period, may have a long term impact on copper solvent extraction. Several scenarios are evaluated regarding existing operations and future solvent extraction projects and cautionary suggestions related to the use of surfactants as leaching aids are given.

Jan 1, 2007

By G. C. Weatherly, D. S. Wilkinson, A. M. Limarga

In addition to the harsh environment, materials for high-temperature applications are often subjected to a significant mechanical loading. Several researchers have noted that the rate of oxidation can be affected by stress in a range of materials. We have recently studied this effect in y-TiAl, based on the preliminary work of Magnan and Weatherly which showed that nitridation rates on the tensile side of a flexural creep specimen could be 10 times higher than on the compressive side. We have since developed a four-point bending creep setup capable of controlled atmosphere testing. We present quantitative data on the effect of creep on scale growth under a range of atmospheric conditions. Finite element analysis will also be used to show how modest applied stresses can have a large effect on scale growth rates through the generation of large stresses due to the mismatch of creep rate between the metallic substrate and the scale.

Jan 1, 2004