Search Documents

By E. L. Bruce

Introduction The Outokumpu copper mine is situated in eastern Finland, 50 kilometers west of the city of Joensuu or 225 kilometers directly north of the city of Viborg (Viipuri), which is situated at the eastern end of the gulf of Finland (Figure 1). The ore-body was discovered in 1910 by Dr. Otto Trüstedt after two years of careful, scientifically-directed, search. During the early period of development of the mine, the ore was treated locally and the copper re-covered by an electrolytic process. Now the ore is concentrated by tables and by flotation. The concentrates are shipped to Germany for refining. In 1929 the mine produced 150,000 tons of ore from which between 20,000 and 25,000 tons of flotation concentrates containing 20 per cent copper were produced. Profits in 1929 were approximately half a million dollars, but the present price of copper will affect very seriously the profits for 1930. The ore reserves are given as between 7 and 8 million tons (1). The grade of ore is stated to be 4 percent to 6 percent copper, with a little zinc.

Jan 1, 1931

By M. Gaumont, F. Robichaud

"Agnico Eagle Mines Limited (AEM) is a Canadian-based gold producer with operations in Canada, Finland and Mexico. In 2010, AEM produced its first gold bar in Nunavut, Canada as it started its Meadowbank operation. It is also in 2010 that AEM acquired the Meliadine property, which is located 25 Km North of Rankin Inlet, Nunavut, Canada. The Meliadine gold project is an advanced exploration and development project, comprising of workers camp, underground and open mines, a processing plant and all the services facilities and infrastructures required to sustain operation in a remote arctic environment.Pending formal board approval, production start-up is planned for Q3 2019 and the process flowsheet is based on an ore processing rate of 1.1 million dry tonnes per year (3,000 dry tonnes per day from underground mining) for the first three years, and 1.98 million dry tonnes per year (5,000 dry tonnes per day from both underground and open pit mining) for the remaining years at 92% process plant availability.To the end of 2015, more than 45 metallurgical test programs have been conducted on the Meliadine deposits. Based on the results of these programs, an optimal gold circuit was designed, comprising of crushing, grinding, gravity separation and cyanide leaching with a carbon-in-leach circuit (CIL), followed by cyanide destruction and filtration of the tails for dry stacking. The assumed gold recovery for the reserves averages 96.0% at a 7.44-g/t gold average mill feed grade."

Jan 1, 2016

By Brigitte J. Dejou

The Red Dog sediment-hosted zinc-lead deposit is located in the Brooks Range thrust belt in northwest Alaska, approximately 1000 km northwest of Anchorage. The mine constitutes the primary deposit in a 400 square kilometre district, which hosts several other mineral occurrences. All the known mineralisation is hosted by the Mississippian Ikalukrok Member, deep basinal shale of the Kuna Formation, part of a Devonian to Cretaceous sedimentary sequence. The rocks underwent intense deformation during the Brookian Orogeny in Middle Cretaceous time. Several thrust faults juxtapose the stratigraphy. The Red Dog mine is composed of four deposits which together contain 105 Mt in resources and reserves for a total resource exceeding 18 Mt of Zn metal. The mine is an open pit with 25 foot high benches. The biggest challenge is not the Arctic conditions, but metal extraction, due to the fine grained nature of the mineralisation and the variability of the ore. The mine produces Zn and Pb-Ag concentrates that are shipped to smelters around the world from the Red Dog port facilities during the short summer period. Ore mineralogy is generally simple and consists of sphalerite, pyrite, galena and marcasite. The deposits are generally overlain by decametre thick exhalative barite horizons and exhibit strong silicification, which locally obliterates the original textures. Although described as a world class Sedex-type deposit, a large portion of the mineralisation exhibits sub-surface replacement textures. Moreover, unlike most other Sedex deposits, the reconstruction of the basin is made difficult by the structural complexity of the district. To assist exploration in the district, several assumptions are made regarding the deposit settings relative to metal source, growth faults or crustal extension.

May 1, 2006

By T. Peters, W. C. Ferguson

"Shebandowan is about 600 miles west of Sudbury and 50 miles west of Thunderbay close to the trans Canada highway. Shebandowan Lake is about 38 miles long. The ore body is located between No. 1 and No. 2 shafts at the lower end of the lake. The economic mineralization lies between 200 and 2000 feet below. Years ago development of this ore body would probably have entailed draining the lake and using the open pit method to mine the ore.The water of Gold Creek which flows into Lake Shebandowan is representative of all local waters and is very close to rain water in purity. It is obvious that any industrial water discharged would have a measurable impact on the local water. The dissolved solids content is low and consistent with what is normally found in northern Ontario.A Koepe headframe is the only visible evidence of the mine from the lake. The Koepe headframe is esthetically pleasing and quiet in operation. The structure is of concrete to control noise. Noise from ore dumping is controlled by dumping underground to an ore pocket 400 feet below the surface. A 3600 foot conveyor belt carries the ore underground to the mill and is out of sight of the lake and the cottagers. The main objective to all our environmental efforts has been to preserve the natural beauty of the region. The mill is housed in a conventional metal-clad-siding building painted in esthetically pleasing colours. A single service building houses warehouse, dry storage and offices. The area surrounding the mill and service building is paved or grassed and drainage from this area is collected and pumped to the tailings area. Air intake silencers are installed on the compressors which are mounted at the back of the mill. Sound measurements taken on the lake indicate that noise suppression is excellent."

Jan 1, 1975

By T. Backers

In fracture mechanics modeling the rock mass is seen as the combination of rock material and fractures, which are evident on different scales. The activation and propagation of fractures dominates the stability and performance issues as well as fluid flow potential. Once fractures have started to grow into each other and create through going separations, stability of rock engineering constructions may be violated. Further, as fracture mechanics inherently incorporated a scaling law in the form of the participating fracture length, scaling issues can be more accurately mirrored. This contribution highlights some examples of application of a fracture mechanics based code on some rock mechanics issues such as numerical laboratory experiments, borehole stability or the creation of fluid pathways due to underground constructions. The results show explicitly the creation of fractures and connection of existing ones, and hence the safety and performance issues. It has to be concluded that the basis for frequent application of fracture mechanics on specialized challenges in Geomechanics is laid, and the needs for future developments are defined.

May 1, 2009

By D Reddy Chinnasane

Outline Location of BirchtreeMine and Layout of 124 OB Cut and Fill Mining Background Purpose of the Studies Methodology Results and Analysis Conclusions and Recommendations

Oct 1, 2010

By Matthew Violot

Introduction ?Located off highway 6, approximately 5 km, SW of Thompson, Manitoba ?Base metal mine: Nickel? Maximum Depth: 4100 ft ?Started Production in 1966 (INCO, 2006)?Halted in 1978?Re-opened in 1989 ?Two types of mining:?VBM (vertical block mining)?Cut and Fill 1.1 Problem ?Birchtree mine is experiencing failures and undesirable dilution in some of their stopes. ?Time can have a large effect on open stopestability. ?Birchtreeis interested in how time is affecting the stability of their stopes. ?The study focuses on the lower 84 complex, which extends from 2750 to 4100 foot level.

Nov 1, 2011

The #3 Shaft at Brunswick Mine, Bathurst, New Brunswick, Canada, intersects a soft graphite zone just below the 3400 Level. Ground movement within this zone causes the concrete liner of the shaft to be deflected towards the shaft?s interior, affecting the steel framework of the conveyance. In some areas, the clearance between the cage and the liner has been reduced to less than 2 cm, which is a concern. An innovative surface-mounted extensometer was designed in 2008 to monitor potential movements of the shaft?s liner. Four such novel extensometers were installed in the shaft for the surveillance of a particularly critical 3.0m by 5.5m area. This article describes the approach taken to instrument the shaft, the principle of the new extensometer, as well as the performance of the instrumentation following its installation.

May 1, 2009

By G. Simard, M. J. Gagnon, A. Charette, G. Péloquin

"In the Bayer process, flocculants are introduced in the feed well to enhance the aggregation of red mud particles. To gain a better understanding of the flocculation process taking place in the feed well, shearinduced flocculation was achieved using concentric rotating cylinders (Couette system). Our previous work has shown the effect of the shear rate on the aggregate’s settling rate and on residual turbidity of the Bayer liquor. In this study, the data demonstrated that the aggregates at selected shear levels appear as a population with a widespread size distribution. By using an imagery apparatus, it was possible to measure the size, the shape, and the sedimentation velocity of the larger red mud aggregates. Marked differences were noticed in the characteristics of the aggregate populations obtained under various shear conditions. IntroductionIn the Bayer process, red mud particles are separated from the liquor in primary clarifiers and washing circuits under the action of synthetic polymers. The agitation in the feed pipe and in the feed well affects the flocculation since the aggregates are formed by the interaction between the red mud particles and the polymers. A minimum shear rate is needed to initiate the aggregation process of fine particles (Warren, 1975).Different systems have been used to study the effects of shear on the flocculation process (Tampo and Watanabe, 1979; Klimpel and Hogg, 1986; Scott et al., 1996; Biggs and Lant, 2000). The Couette flow system has been used in some studies on shear-flocculation (Oles, 1992; Farrow and Swift, 1996a, 1996b). The importance of the physical properties of the aggregates in determining the efficiency of the solid-liquid separation process within a given gravity thickener has been demonstrated (Farrow and Warren, 1989a)"

Jan 1, 2002

By S. Tuttle, R. Sisson

"Suncor Energy Inc. has proposed a 2.2 billion dollar expansion to the current oil sands operation, which will more than double the productive capability of the facility. As part of the application for this expansion, a comprehensive closure plan had to be developed and filed.Closure planning includes a systematic evaluation of the area to be developed, the development activities planned, the goals and objectives of the corporation in re-establishing landforms and ecosystems at the same time as running an effective operation. As early as is practical during the mine development, surface contouring is completed, soil is reconstructed, and vegetation, surface drainage and wetlands are re-established. Once active reclamation is complete and vegetation has been re-established, Suncor monitors maturation of landscapes and ecosystems to provide the submission basis for reclamation certification"

Jan 1, 1999

By G. Zhu

The straight Y-shaped silica nanorods have been synthesized on Si wafer by thermal chemical evaporation of mixed powders of silica and graphite at 1300_ and condensation on Si substrate without assistance of any catalyst. The synthesized samples were characterized by means of scanning electron microscopy, transmission electron microscopy. The results suggested that the straight Y-shaped silica nanorods have uniform diameter about 50-200nm and neat smooth surface. The growth of such silica nanorods may be a result of the fluctuation of external conditions and internal structure faults causing a change in the growth direction of silica nanorods developed.

May 1, 2008

By Malcolm Scoble, Jean-Marc Robert, Luciano Piciacchia

"An approach to the in situ testing of mine backfills is outlined. It has been developed to provide a measure of the effective strength and stiffness of such materials after placement in stopes. This paper is based upon recent field studies undertaken at five Quebec mines. Details of the selected instrumentation, supporting equipment and testing procedures are reviewed. The mechanical behaviour of the backfills is reported and related to their physical properties. This approach represents an economical, simple and reliable means to assess the mechanical characteristics of backfill materials as an aid to both mine design and placement quality control. IntroductionDevelopments in backfill and mining method technology are creating a pressing need to develop effective techniques for characterizing the physical and mechanical properties of backfill in situ, rather than relying on traditional laboratory testing. The development of bulk mining methods is creating the requirement to more fully understand the nature of exposed fill faces to design for stability in pillar recovery operations. Other backfill technological developments currently receiving widespread attention are high density placement and the use of alternative additives to Portland cement. In Canada, U.S.A. and South Africa attention is also being placed on employing backfill to alleviate rockburst hazards(1,2.3l. In situ testing offers the potential to measure the geomechanical properties of backfill once placed in stopes , in order to assess its actual role in pillar recovery and ground support. Similarly, it offers the ability to provide some quality control during backfill placement. This role is seen as becoming increasingly important with the growing recognition of the need to pay greater attention to the mode of placement, which governs segregation and variation in the properties actually achieved by the backfill after placement."

Jan 1, 1987

By S. Yalcin, S. Chang, M. Oliazadeh

"Present day ferrochrome demand is on the rise, as more steel products require this material as an alloying element. It is projected that the stainless steel demands will grow by about 6% per year to 2020; as such, the supply and demand for ferrochrome appears promising. Chromite is the only economical source of chromium, which is commonly upgraded by gravity techniques and used to produce ferrochrome. The gravity separation methods are not able to treat particles finer than 0.1 mm efficiently. Therefore, in processing chromite ore, a large quantity of fine tailings; some 25% of the mineral values have been reported as lost in slimes during processing. The chromite content of these tailings is typically 10-20% Cr2O3 and accumulates into a large stockpile/pond. A chromite concentrator project in Canada, considers a cut-off grade of 20% Cr2O3. This indicates further processing might be required to recover chromite from low-grade stockpile when the high-grade deposits are depleted. Low-grade ores normally indicates disseminated chromite ores with low liberation and consequently fine comminution. This paper reviews the techniques for treating chromite from fine material and provides some examples of successful operations in fine chromite recovery. Beneficiation techniques for fine particles include gravity separation, magnetic separation, and flotation. Several case studies are presented here that used one of the aforementioned methods or a combination of them.INTRODUCTIONChromium is one of the essential element and important material for production of ferrochrome alloys and special steel. Chromium occurs as chromium spinel, a complex mineral with chemical composition of (Fe, Mg) O (Cr, Al, Fe)2 . Chromite ore is exclusively found in ultramafic igneous rocks. Major associated gangue minerals are talc, quartz, serpentine and iron oxides.Chromite is a heavy mineral, with a specific gravity in the range of 4-5, relative to associated gangue minerals in a chromite ore, which makes gravity concentration a suitable process. This is generally true for coarse particles, ranging from 1 mm to 100 mm. Typically, the ore is prepared by crushing (and grinding if necessary) to a suitable size and the material is sized for the appropriate beneficiation techniques. It is common to use heavy medium separation (e.g. dense media drums, dense media cyclones, or Dyna Whirlpool) to treat coarse size and intermediate size particles (1 – 100 mm). Intermediate and fine particles (20 – 0.1 mm) could be treated by jigs. Spirals, shaking table, sluices, and Reichert cones can upgrade fine particles. Figure 1 shows a typical chromite beneficiation process flowsheet. As can be seen, it consists of three major sections: feed preparation (crushing, screening), de-sliming, and concentration. Beneficiation recoveries range from 80 to 85%, although the ratio of upgrading is only 2 to 3."

Jan 1, 2013

By Juan Anes, Dominic Fragomeni, Tim Edwards, Dave Scott, Simon Yu

"The Montcalm concentrator operation was successfully commissioned in fall of 2004 at the Xstrata Copper’s Kidd Creek Metallurgical Site, Timmins. The start-up met or exceeded the Type 1 profile as defined by McNulty. Since the life-of-mine was estimated at seven years, concentrator optimisation endeavours had to be fast-tracked. These joint endeavours between the Kidd Creek Metallurgical Site staff and Xstrata Process Support were focussed on increasing ore treatment capacity and metallurgical performance. This paper reviews these endeavours. A flotation circuit survey, together with appropriate Process Mineralogy measurements, identified recovery opportunities in both locked and overground pentlandite in final tailings. The bypassing of first rougher concentrate directly to final concentrate was also recommended, given the composition of that stream. A subsequent grinding circuit survey identified a low circulating load due to poor classification performance. Modelling of these data suggested a change to the cyclone nest and pumping arrangements in the grinding circuit. Implementation of these recommendations has led to a 25% gain in milling circuit capacity as well as improved flotation circuit performance. These improvements amount to nickel and copper recovery gains of 2.57 and 1.83% respectively.INTRODUCTIONHistoryThe Montcalm Ni/Cu Ore is processed in a spare division of the Xstrata Copper’s Kidd Creek concentrator, located near Timmins in Northern Ontario. The flowsheet had been specified by earlier work, and the project fast-tracked so as to commission production operations into a time of rising nickel and copper prices. The Montcalm flow sheet starts with on-site ore crushing to - 19 mm. The crushed ore is trucked to the concentrator. This off-site crushing minimizes contamination with the Kidd Creek Cu/Zn ore. In the concentrator, rod and ball mill grinding to a target p80 of 39 µm produces the Rougher Flotation Feed. Flotation to Bulk Concentrate follows as Cu/Ni roughing and two stages of cleaning. Bulk concentrate is subjected to Cu/Ni separation using conventional column cells. Xanthate is the collector and MIBC is used as frother. Depramin C, a CMC (Carboxy Methyl Cellulose) is added to depress ferromagnesian silicates in the flotation process."

Jan 1, 2009

By Nick D. Rose

The Dy deposit is a 21 Mt Pb-Zn-Ag-Au SEDEX-type massive sulphide resource located in the Anvil District, Faro, Yukon. This relatively unexplored orebody lies at a depth of 480 to 920m below surface, dips 20 to 35o and comprises vertical ore thicknesses of 3 to 28m at a 9% Pb + Zn cut-off grade. The deposit has been tested at depth with 63 surface diamond drillholes, but has not yet been explored or developed by underground means. Over the past decade, pre-feasibility investigations were conducted for two separate owners of the property to determine the economic viability of developing an underground mine at Dy. Following these previous studies an assessment was undertaken between 1998 and 2000 to further investigate geotechnical considerations for underground mining. The results and conclusions drawn from this study provide direction for possible future exploration at Dy.

May 1, 2002

By Rodolfo Espinosa Gómez

"Industrias Peñoles, S.A. de C.V. – Mining Division, has initiated in the last ten years, six Mining Operations (Bismark, Tizapa, Ciénega, La Herradura, Rey de Plata, and Francisco I. Madero) and it has expanded several of their existing Operations (Sabinas, Fresnillo, Tizapa, Ciénega) one or more times.This work aims to share the experiences learned on this growing process. Some of these lessons are: 1) Project leaders must have a leadership that fosters good communication and team work; and this leadership style must come from top management. 2) A good communication must exist between the personnel from Engineering, Construction, and Operation. Also, this good communication must come from top management. 3) Starting the project with a solid Engineering Study. 4) Do not misunderstand cost with cost/benefit; always look at the cost/benefit. 5) Selecting good Contractors and good Suppliers. 6) Good training before the project commissioning is essential to reduce the learning curve period, this is even more important in areas where local people do not have any background in mining activities. 7) Recognizing that any project has a learning curve and it must be reflected on the production budget. 8) Avoid an over optimistic Mine preparation time schedule.BACKGROUNDIndustrias Peñoles S.A. de C.V.The mission of Industrias Peñoles, S.A. de C.V. (Peñoles) is to add value to non-renewable natural resources in a sustainable manner. Peñoles seeks to build long-term shareholder value; provide their customers with the highest quality products and services; maintain productive longterm relationship with their suppliers; develop and promote the capabilities of their personnel; foster mutually beneficial relationship with the communities in which it operates, and preserve the environment.Peñoles was established on 1887. It is a Mining Group with integrated Mining, Smelting and Refining operations of non-ferrous metals, and also produces inorganic chemistry materials. Peñoles is the main World producer of refined silver, metal bismuth, and sodium sulphate; Latin American leader in the production of refined gold, lead, and zinc.The Mining Group is made-up of nine mining operations producing concentrates with high gold, silver, lead, zinc, and copper contents. It produced in 2002, 365,900 ounces of gold; 52.7 million ounces of silver; 86,820 tonnes of lead; 266,000 tonnes of zinc, 11,840 tonnes of copper; with a total values of 3,780.6 million of Mexican pesos (~ $ 378.0 million U.S. Dollars)."

Jan 1, 2004

By Andy Cole

Barrick Gold recently implemented an oxygen roasting process to treat carbonaceous ore from its Goldstrike property in Nevada. One of the key project challenges was the design of the roaster gas cleaning system, which was driven by the requirements of a strict air permit and the need to achieve very high reliability. The roaster gas systems include multiple stages of wet particulate collection, a dual-alkali SO2 scrubber, mercury scrubbing, CO oxidation and NOx reduction. This paper describes the gas system, the influence of regulations on project implementation, and performance of the system.

May 1, 2002

By Leslie F. Sawatsky

Failure of drainage works is one of the principal threats to the sustainability of mine closure facilities but the risk can largely be remedied by appropriate design of mine closure drainage facilities. The feasibility of sustainable mine closure facilities that avoid failure of drainage systems needs to be established during the early stages of mine planning, before mine disturbances make sustainable closure uneconomical. Experience in mine development shows there is often enough latitude in mine plan development to incorporate measures with neutral economic consequence and positive environmental benefit. Project managers need to resist the temptation to develop mine plans and closure drainage plans independently. Integrated mine planning with effective inputs by environmental specialists and drainage designers may affect the overall mine configuration, footprint and schedule. Key issues pertain to the end pit location, waste dump configurations, pit infill elevations, fluid impoundments, diversion channel routing and preservation of flows to receiving waters. Guidelines with illustrations of suitable practices are presented to assist mine planners.

May 1, 2004

By James F. Archibald

In historic mining practice, typical thin liner support systems have been considered to comprise non-reinforced or mesh-reinforced shocrete linings. In the early 1990?s, development of alternate forms of liner systems was initiated in Canada which is now undergoing significant international growth in countries which sustain major mining activity. Now internationally designated as thin, spray-on liner systems, a wide spectrum of liner materials, ranging from liquid/liquid to liquid/solid component combinations, has become commercially available. This innovative family of products is characteristically identified as being rapidly deployable, capable of creating ultra-fast setting coverage over rock surfaces, and able to develop tenacious adhesion and pull strength capacities for resisting rock falls and movements. This paper presents a summary of current liner developments and use in principal mining districts world wide. Additionally, a database of material properties for principal product types used in mining and a review of common quality control testing procedures under development are provided. Such information is based upon recent Canadian and international efforts being taken to assess and develop user standards for the implementation of thin, spray-on liners as rock support in mines. This work is intended to continue for a period of years, with the eventual goal being to establish support and installation guidelines for mines based on quantifiable laboratory and field research.

May 1, 2002

By Greg Rasmussen

"Huckleberry Mines Ltd is an open pit porphyry copper-molybdenum mining operation located 120 km south of Houston, British Columbia with a 18,000 tpd milling facility. Huckleberry Mines is owned 60% by Princeton Mining Corporation, the operator, and 40% by Japanese partners.The Huckleberry deposit is one of several porphyry systems located in the Tahts a district of the intermontane belt of British Columbia. The principal economic minerals are chalcopyrite and molybdenite. The ore deposit is split into two ore deposits, the Main Zone, consisting of24,241,000 tonnes of mineable reserves grading 0.484 %Cu and 0.013 %Mo, and the East Zone, consisting of 66, 131,500 tonnes of mineable reserves grading 0.523 %Cu and 0.014 %Mo.The milling begins with gyratory crushing. This sizes the product down to 100% passing 6 inches. This product is discharged onto a stockpile by a stationary conveyor. The stockpile was designed for a capacity of 144,000 tonnes with a live capacity of 20,000 tonnes. Two apron feeders draw the ore from the bottom of the stockpile and discharge onto a SAG mill feed conveyor which in turn feeds a grinding circuit consisting of one 32' x 15' SAG mill and two 30' x 16.5' ball mills. The grinding cyclone overflow feeds bulk flotation at 55 -65% minus 200 mesh.The bulk flotation uses conventional rougher and column flotation methods to float a bulk concentrate recovering 92.6% copper on the East Zone and 95% copper on the Main Zone with 75% recovery molybdenum on both zones. The bulk concentrate feeds the bulk thickener which produces a density of 60 %solids. This in turn feeds the molybdenum circuit, which separates the copper and molybdenum, by depressing the copper then using conventional rougher and column flotation produces a copper concentrate of 27 %Cu and 0.02 %Mo, and a molybdenum concentrate containing 1.5 %Cu and 54 %Mo at 67% recovery. These concentrates are separately thickened, filtered, dried, and shipped to the smelter for processing."

Jan 1, 1998