Search Documents

By A. Saramak

"The paper focuses on problems of atmospheric pollution by the dusts, produced during the course of crushing and grinding processes, and the main objective of investigative programme is an assessment of emission of particulate pollutants for following crushing devices operated in plant scale: impactors, cone and jaw crushers. All crushers operate in aggregate production plants in Poland. In the first stage of investigations there were determined dust emission levels and supporting characteristics for all crushers under investigation. Then there were introduced indices that allow for comparative analysis in terms of dust emission, for devices with different energy consumptions and comminution ratio. It appeared that crushers with high the overall dust emission do not always achieved unfavorable dust emission per comminution ratio or energy consumption. The introduced indices proved their usefulness, because they helped to carry out a comparative analysis among crushers, operating under different technological conditions. It is also easier to assess environmental impact of individual crushing devices, under analysis. Results of investigations also show that environmental impact of different types of crushers is diverse and it is difficult to compare dust emissions of various types of crushers without taking into account technological aspects (like throughput, comminution ratio, energy consumption, and others) of their operations.INTRODUCTION Mineral processing of raw material is a complex process, involving in general operations of size reductions and separation. Depending on the type of specific raw material, the technological circuit may include operations of comminution and size classification. This is a typical circuit for aggregate production. In ore treatment industry the process in much more complicated and include also a metallurgical treatment of ore concentrate – the final product from processing plant stage.In general, regardless the type of raw material, operations of size reduction are present in each technological circuit of mineral processing. Operations of crushing and grinding are an integral part of processing technology, because they play a crucial role in effective treatment of mineral raw materials (Gawenda 2013). Their duty is to liberate the useful minerals from the gangue in ore treatment industry, or to produce the material with the required particle size in case of aggregate processing. Crushing and grinding operations are of a high negative impact on environment and humans. They consume great amounts of energy, what indirectly contributes to higher emission of carbon dioxide CO2. Apart from energy, crushing and grinding device consume significant amount of steel and other metals and alloys due to high wear of working parts and grinding media. This is also of negative environmental impact due to emissions of additional amounts of CO2 in production of steel and other metals required as spare parts for comminution devices."

Jan 1, 2018

By A. Ekrem Yüce, Gülay Bulut, Feridun Boylu, Vecihi Gürkan, Istanbul Technical University, H. MustafaTarkan

"Nickel sulphide ores subjected to this investigation were taken from Orhaneli district where widespread chromite mineralisation can be occurred. Significant amounts of magnetite and chromite have been existed in the ore together with sulphide and oxide type nickel minerals. Ore sample is constituted about 70% magnetite, 15% sulphide minerals, 5% chromite and iron oxides as well as 10% gangue minerals.According to the chemical analysis results, the representative ore sample contains 1.32% Ni, 10.8% SiO2, 78.4% Fe2O3, 1.3 g/t Ag and 1.0 g/t Au. Mineralogical examinations showed that pentlandite (Fe, Ni)9S8, violarite (Ni, Fe)3S4, millerite NiS and asbolane (Co, Ni)MnO2.(OH)2.1-2H2O were the main nickel minerals and magnetite, chromite, chromium spinals, pyrite, pyrhotite, chalcopyrite, cubanite, goethite, hematite, limonite, rutile, chlorite, talc and serpentine group minerals as associated minerals.The aim of this investigation was to produce valuable nickel concentrates by using gravity separation, magnetic separation and flotation methods. As a results of laboratory scale studies, alternative flow sheets for the production of nickel sulphide concentrate were developed. The related experimental results are given in Table 1."

Jan 1, 2003

By Aldo Cipriano, Fernando Estrada

The mining industry is in search of control strategies that allow considering a global optimization of their processes, ensuring their stability. This has led to the application of recently developed control techniques on large-scale systems in the mining processes. One of the most important process of the mining industry is the mineral grinding, as the product particle size impacts, in a significant manner, the recovery rate of the valuable mineral in the separation stages. As a solution, a centralized hybrid model predictive control (HMPC) is presented; this control approach maintains the product particle size on a defined range and minimizes energy consumption, maintaining the grinding plant in a stable operation. As a comparison, a conventional model predictive control with an expert system to handle discrete events was developed, showing HMPC is a suitable solution that can used in the grinding process, with the benefit that it handles in the same controller both discrete and continuous dynamics and events.

Jan 1, 2014

By Weiguo Xie, Malcolm Powell, Lian Liu, Ping Yu

"In order to develop a common mathematical and simulation platform for tumbling mills, a review of existing mechanistic models was made identifying the key aspects of grinding and slurry transport which are common to all tumbling mills. A mill model structure has been developed for all types of tumbling mills based on the population balance framework by incorporating breakage characteristics, slurry and solids transport, product classification and discharge, and energy consumption. A size-dependant breakage model developed by the JKMRC is applied. Transport is separated from breakage events and treated as a main sub-model in the new model structure. The model structure is based on dynamic time-stepping technique to enable dynamic simulation capability for non-steady-state simulation and control modelling. It is envisaged that the new model will cover a full range of milling conditions. It should enable a smooth transition between different mill types, such as from AG (Autogenous Grinding) to SAG to ball mill. The dynamic mill model structure developed here is the first step towards mechanistic modelling of grinding mills and provides great potential for the optimization of the comminution process."

Jan 1, 2014

By Jaime Sepúlveda

"A broad diversity of critical operating conditions may influence, in very convoluted ways, the actual performance of any given mineral processing system, to the extent that it becomes nearly impossible to empirically determine the independent, decoupled impact of each condition. An effective approach to better understand the behaviour of such complex systems is via the extensive use of sufficiently detailed and reliable mathematical models, allowing the process analyst to explore and learn about the independent effect of all relevant operational conditions. Certainly, these tasks are greatly facilitated if the appropriate software tools - such as the Moly-Cop Tools software package - are readily available. Moly-Cop Tools 3.0 is a set of 63 easy-to-use EXCEL spreadsheets designed to help process engineers characterize and evaluate the operating efficiency of any given grinding circuit, following standardized methodologies and widely accepted evaluation criteria. Moly-Cop Tools 3.0 covers conventional and semiautogenous mills, crushers, HPGR’s, rod mills and vertimills, with the corresponding mass balance and parameter estimation routines; plus complementary spreadsheets regarding Bond’s Law calculations, grinding media selection and performance evaluations and other useful utility functions. As a relevant example of application, specifically focusing on semiautogenous grinding operations, the current publication describes how the models can help us learn and rationalise critical empirical observations such as the relationship between feed particle size and optimal ball filling, the role of the rocks as autogenous grinding media as well as the impact of feed size and discharge grate opening on the mill grinding capacity. Over the last 20 years, Moly-Cop Tools has gained wide acceptance around the mineral processing community in recognition to the quality of the mathematical models contained, their simplicity of application and ease of sharing of the calculations amongst all interested parties, since it is available free-of-charge with no restrictions to make as many copies as needed."

Jan 1, 2014

By J. D. Miller

The more efficient production and use of mineral resources is a major objective of our sustainability efforts. Resource characterization is a critical component for optimization of the mine-to-mill process, including innovative processing for sustainable growth. Such characterization is now referred to as geometallurgy, with advanced instrumentation including, for example, particle size analysis, XRF, XRD, NIR, automated SEM/EDAX analysis (QEMSCAN, MLA), and high resolution X-ray micro tomography. Geometallurgical information is important for exploration, deposit evaluation; mine planning, design and analysis of separation processes, etc. Characterization of mineral processing particles in 3D is now possible using high resolution X-ray micro tomography (HRXMT), and such HRXMT systems have been installed at several laboratories around the world. After review of principles, the features of such HRXMT analyses are presented including size/shape, damage state, mineral phase identification, and evaluation/isolation of trace mineral particles. With new algorithms for image analysis, quantitative data treatment is possible for construction of liberation-limited grade/recovery curves, for the determination of specific crack surface area, and for complex texture analysis including grain exposure. Finally, new tomographic characterization possibilities are discussed to provide the foundation for the development of advanced, innovative processing strategies for sustainable growth. Keywords: X-ray tomography, resource characterization, HRXMT, particle size analysis XXVI INTERNATIONAL

Sep 1, 2012

By O. A. Punishko, G. G. Mineev, Zabaikalsky Ore-Dressing Plant, M. V. Malova, O. V. Belousova, S. A. Bogidaev

"In order to intensify benefication processes (flotation and magnetic separation) for rebellious tantalitecolumbite ores electrochemical machining of pulp (ECM) is suggested instead of costly mechanic-chemical activation and magnetizing roasting. Any change in the surface mineral-semiconductor potential under the action of electrochemical treatment results in the change in the isoelectrical state of the surface and the adsorption property of the mineral with respect to ionogenic reagents-collectors. In this case conditions are created for regulating the ion composition, reduction-oxidation potential and pH of the liquid phase of the pulp without any extra introduction of expensive and often ecologically harmful chemical substances.Ores containing tantalum and niobium are characterized by complex chemical composition, determining their physical properties (conductivity, dielectric penetration, magnetization value, etc.) and their electric susceptibility.The authors investigations show that the pulp electrochemical treatment leads to the increasing magnetic susceptibility of the paramagnetic minerals. The main chemical elements forming the columbite-tantalite minerals except tantalum and niobium are iron and manganese. They determine the rare-metal minerals paramagnets properties. The electrochemical treatment changes the relation of the oxidized and reduced forms of these elements having. The method of cathode pulp treatment before flotation is successfully tested industrially.In the field of noble metals metallurgy new technological proposals are reduced to the following. As is know, the production of noble metals from unusual raw materials demands the elaboration of principally new technologies new technologies in so far as the methods for gold and silver extraction from ores are as a rule low elective and at the existing level of engineering are economically not expedient.The analysis of the main trends in the field of non-standard raw material treatment shows that the perspective ones are the geo- and biotechnological processes (underground leaching and leaching in heaps - UL and HL and microbiological methods of metal extraction)."

Jan 1, 2003

By V. Panayotov

Slag and by-products of metallurgy bear valuable components and their processing raises an in-creasing interest. Coke and iron have to be separated and other components have to be depressed, in order to obtain sellable high quality copper concentrates. Use of classical mineral processing technologies, such as magnetic separation, sulphidization, hydrometallurgy, etc. yields copper concentrates with grade of 4%~6% Cu. Copper is lost in tailings and the whole technological cycle is low profitable. Technology proposed applies an electrochemical treatment of the industrial water entering the flotation cycle. Iron and iron compounds that do not bear Cu, coke and gangue materials are depressed during the copper flotation. Copper concentrate of grade of 9.8%~10% Cu is obtained at simultaneous increase of Ag recovery by 8%~10%. As a result company profitableness is increased. Technology proposed is easy to implement, it does not require changes in the existing technology flow-sheet, and additional investment is low. The flotation process can be aided by a specially developed system for real-time analysis of the obtained copper concentrate which allows in-time corrections in the flotation parameters and entire process control. Applied flotation schemes, technological parameters and results obtained are described.

Jan 1, 2014

By J. B. Rubinstein

"The paper gives an overview of the history of flotation machine development. The laws of their evolution are stated and the place and role of column flotation are demonstrated.The major parameters of column cell diameter and height are discussed. Options are proposed for optimization of the hydrodynamic characteristics of large-capacity column cells. The high efficiency of columns with cell height of 4-6 m is demonstrated. The optimum parameters of multisectional column machines are determined. Their advantages compared to monocells are shown. A scaling-up procedure for column machines was developed based on flotation macro- and microhydrodynamics simulation."

Jan 1, 2003

By J. Roth

The increasing demand of the filler industry regarding fineness and better delaminated products led to the development of a series of different grinding machines, which differentiate basically by the grinding mechanism as well as the kind of classification. Spiral jetmills grind, as it is well known preferably by delamination, therefore a spiral jetmill with integrated dynamic classifier has been developed. Especially the enhancement of the functional properties of the used industrial mineral fillers is a factor of highly increasing importance. These properties are very often bound to the platy shape of the minerals expressed by the aspect ratio. The developed Spiral Jetmill shows sufficient ability for such delamination and therefore increases in aspect ratio. In a series of comparative tests the suitability and advantages of this system regarding achievable fineness down to the submicron range as well as the conservation or even improvement of the aspect ratio of different minerals has been studied. As an emphasis on the results application tests with certain materials in the plastics field have been conducted. Due to the fact that in this range the required specific energy for achieving the necessary fineness increases exponentially another target is to optimize the grinding efficiency. A special feed control system provides on one hand a sufficient load inside the mill to obtain maximum utilization of the applied energy and on the other hand to prevent the mill from overfilling and coming with this a poor classification. The integrated classifier is a combination of a high speed motor with directly attached classifier wheels. This unit on one hand grants the necessary high circumferential speed of up to 190 m/s for providing an exact top cut of the ultrafine products and on the other hand gives the required operational reliability for continuous operation. Hard grindable impurities, which enrich inside the mill chamber, can be rejected from the process leading to an even cleaner product. Comparative tests on a talc product with certain free quartz impurities showed a significant improvement of the final product with respectively low loss on rejected material. This effect again had a beneficiary impact on the suitability of the final product when used in plastics application.

Jan 1, 2014

By Y. M. Zhu, G. C. Gong

"The influences of citric acid (CA) on the flotation behavior of cassiterite using styrene phosphonic acid (SPA) as the collector were studied via single mineral flotation tests, contact angle measurements, zeta potential determinations and solution chemistry calculations in this paper. The results of single mineral flotation tests revealed under the conditions that pH=4 and the dosage of SPA 100 mg/L, the recovery of cassiterite reached 76.78%. The addition of 20 mg/L AC decreased the recovery by 12.42% at pH=4. Contact angle measurements demonstrated the adsorption of CA prior to SPA made the cassiterite more hydrophilic. The results of zeta potential determinations and solution chemistry calculations indicated the chemisorption of C6H7O7- and C6H6O72- filled parts of the Sn site on cassiterite surface and prevented the SPA from getting adsorbed. The hydrophilic effect of AC was stronger than the hydrophobic effect of SPA and the flotation of cassiterite was crippled. INTRODUCTION Tin is an important metal which is widely used in medical instruments, marine engineering materials, electronic and electrical devices, welding, weapon manufacturing and organotin compounds industries (Angadi et al., 2015). Cassiterite is the only mineral from which the tin can be extracted, thus it is of great importance to efficiently exploit the cassiterite mineral. Flotation is an indispensable method for the recovery of cassiterite (Li et al., 2015). However, cassiterite is usually in association with many other gangue minerals which are of similar floatability, such as quartz, calcite, fluorite, iron oxide, wolframite, scheelite and tourmaline (Sreevinas, 1997). So some modifiers are necessary in the cassiterite flotation process. The amounts of the modifiers used in the flotation must be judicious and the overmuch modifiers may cripple the recovery of cassiterite (Parsonage et al., 1987). Nevertheless, the research about the effects of the modifiers on the flotation behavior of cassiterite has been rarely reported. In this paper, the influences of citric acid (CA) on the flotation of cassiterite using styrene phosphonic acid (SPA) as the collector were investigated by flotation tests, contact angle measurements, zeta potential determinations and solution chemistry calculations."

Jan 1, 2018

By S. S. Yu

In this paper, the producing process of using V2O3 as raw material to obtain vanadium nitride was analyzed through the means of thermodynamic. The analysis shows that conversion follows the principle of reduction step by step in the conversion process of V2O3. The temperature of the reaction system has prominent influence on the nitrogen content of products, and the reaction is very sensitive to temperature. As raising temperature, the fine grain structure of the nitrides is more evident, and the grain size of nitrides increases. At 1703K, the nitrogen content of the products tended to be constant after soaking over 3 hours.

Jan 1, 2014

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, A. Abazarpoor

The research aimed to compare the chemical analysis (K, Na, Cl) of Iranian concentrate plants, which are the main source of materials corrosion in the pelletizing plants. Cl alongside alkaline elements (especially K) may cause corrosion and plug in the grate plates and other involved equipment. Therefore, it is tried in the processing plants to remove impurities from the concentrate to prevent potential problems in pelletizing and iron/steel making processes. Part of these impurities are existed in the nature of ores and others are sourced in the processing water. Various samples from the largest Iranian concentrate plants including Chadormalu, Gol-e-Gohar, Jalal-Abad and Sechahun were prepared to investigate the possibility of alkaline problems for each samples. The amount of Cl, K and Na of Chadormalu sample was obviously low and therefore no alkaline problem is expected. The Cl content of Gol-e-Gohar sample was high (980 ppm) while amount of K was less (0.008 Wt. %). Due to low content of K, most of Cl will release as Cl2 or HCl and so problems caused by KCl plugging would not be a problem. The amount of Cl in Sechahun case was nearly same as Jalal-Abad (400-600 ppm), higher than Chadormalu and less than Gol-e-Gohar samples. However, the K content was higher than all samples (0.04 Wt. %). Therefore, the amount of evaporated K would be 2-4 times more than other samples. Since the amount of Cl and K is simultaneously higher than usual iron ores, therefore alkaline problems may be a serious prevention factor for the continuous operation of this plant. In order to solve this problem some counter-measures is suggested and discussed including cleaning system, partial dust enriched with KCl removal and variation in the materials type of involved equipment.

Jan 1, 2018

By G. V. S. Murthy

Beach Placer Ilmenite is an important source for production of titanium metal, titania slag and pigment grade titanium dioxide. Besides, these well known applications for which Ilmenite is mined and processed, there are other emerging processes that are being tried for obtaining highvalue products. Synthesis of Ilmenite based materials for varistor applications and direct electrochemical reduction of Ilmenite to produce ferrotitanium are two such attempts being discussed in this work. In this paper, recent efforts undertaken to study the electrical and magnetic characteristics are discussed. Ilmenite, FeTiO3, is one of the mixed-valence transition metalbearing minerals, inwhich Fe can be in two different oxidation states, Fe2+ and Fe3+.. Similarly, Ti can be in Ti3+ and Ti4+.Ilmenite is inherently suitable for making Varistors, which are devices, used for limiting the transient voltage surges in a circuit. Varistors produced from Ilmenite can withstand harsh environments seen in nuclear reactors and outerspace. Electrochemical reduction of Ilmenite can be used to prepare ferrotitanium directly without any reductant. The process essentially involves removal of oxygen from the mineral through electrolytic action using calcium chloride as electrolyte and graphite as anode. At a temperature of 950°C, it is shown to be possible that all the oxygen can be removed from the Ilmenite sample, which passes through the electrolyte, to form CO/CO2 at the anode. The process has immense potential for cost effective production of titanium metal as well. Results of the above developmental works are presented in this paper. Keywords: beach placer ileminite, varistor applications

Sep 1, 2012

By F. C. Yi

Discontinuous and consecutive process was applied to probe into the Kinetics and adsorption theory for Cs+ adsorbed by Zeolites under the conditions of temperature, time and fixed-bed dynamic adsorption. It indicated that the sorption kinetics behavior of zeolite?s sorption on Cs+ is ac-cord with pseudo-secondary velocity equation, velocity constant k2=0.0005213 g?mg min-1, and equilibrium adsorptive capacity is 147.0588 mg?g-1; The equation can be expressed as: Y=0.0068X+0.0887; From the analyzing of diffusion coefficients on different temperatures and times, the coefficient of diffusion is not only related with the fabric of mineral and the character of ions but also the temperature and time; When the ambient temperature hoisted, the diffusion velocity augmented rapidly; Cs+ would get over a certain energy barrier when it enters into structure of zeo-lite; This energy is expressed by activation energy, and its value is E=131.668818 kJ?mol-1; There are two dominating adsorption mechanisms in the system of zeolite absorb Cs+: ionic interchange and surface coordinate adsorption.

Jan 1, 2014

By E. A. Brocchi

This work is dedicated to the chemical treatment of a typical EAF dust by chlorine content agents. The residue contains 48% Fe2O3 and 28% ZnO mainly in the franklinite structural form. The others less compounds are: 4.00% CaO, 2.60% MnO, 2.20% MgO, 1.08% PbO, 0.36% Cr2O3, 0.21% B2O3, 0.03% CdO and 0.01% NiO. The experiments purpose is selectively to remove zinc from the residue leaving the iron behind. Thermodynamics studies have indicated some roasting possibilities. The experimental results have shown that both HCl leaching and carbochlorination will remove iron and zinc without any selectivity. However, either the chlorine or the calcium chloride roasting seems to form, preferentially, the zinc chloride. So, it will be presented how the EAF Dust can be treated by the using of chlorine roastings process such as carbochlorination in order to separate the zinc and iron present in the frankilinite, main EAF dust content.

Jan 1, 2014

By E. Pourjenaei, P. Ghobadi

High Pressure Grinding Roll (HPGR) is efficient equipment in comminution process. HPGR could be a good option for preparing ball mill feed at the first stage of grinding due to its high efficiency and low energy consumption. Closing with a screen, these mills are utilizing as one of the principle parts in mineral processing industries, especially for iron ores. Recently, HPGRs are working as primary mills at 4 developing lines in Gol-e-Gohar Iron Ore Processing Complex, Iran. Different mechanism of particle crushing in compare to the other tumbling mills makes the HPGR as certain equipment with its own particular controlling parameters. Hydraulic pressure, roller speed and level of material inside feeding hopper are the most important variables influencing grinding efficiency of the HPGR. To figure out how they impress the process and operation situation, different industrial tests were carried out and the best result (d80 about 8 mm for HPGR discharge) was achieved at 180-190 bar pressure (P), 300 rpm speed (S) and 50% of hopper level (L). It is worth noting that this finding has been observed through past pilot test too. We also used design expert method (DX7 software) to develop the best design and analysis the test results, as well. According to the mechanical restriction of HPGR and process limitation in the plant (based on the industrial results), we adjusted value of each parameter in a logical range. Therefore, 20 industrial tests were conducted, as DX7 recommended, and the various impacts of the parameters and their interaction were identified based on statistical analysis. As the authors expected, it was revealed that after presser, roller speed is a critical variable because of its significant role in residence time of the particles between the rollers. The function below has been determined to explain the relation between different parameters and the response.

Jan 1, 2018

By Erico Tabosa, Meng. Jun, Kym Runge, Matthew Brennan, Weiguo Xie, Dee Bradshaw

Turbulence and its distribution are of great importance in flotation cell design as they affect suspension of particles, air dispersion and particle-bubble collision rates, which in turn determine flotation performance. However, there is no mature technique to measure turbulence in three phase (liquid-solid-gas) systems such as in flotation cells. In this article, the authors present two new approaches that are suitable for measuring turbulence distribution in three phase systems and validate their applicability. The first technique uses a piezoelectric vibration sensor (PVS) to measure fluid kinetic energy standard deviation and the second technique applies electrical resistance tomography (ERT) to measure conductivity variation at a measurement position in a flotation cell. For the PVS technique, calibration of the sensor was performed to determine the values of parameters that were needed to calculate the force applied to the sensor. Then measurement was conducted in a 60L batch flotation cell and the results were compared with LDA measurement. This demonstrated that the piezoelectric sensor signal provides a good representation of fluid kinetic energy standard deviation at the position of measurement. For the ERT technique, conductivity distribution data was processed to give conductivity variations, which were then used to calculate fluid kinetic energy standard deviation at the measurement position. The spatial distribution of turbulence obtained by performing multiple measurements at different positions in the 60 litre batch flotation cell was found to agree with the PVS measurement results. These two techniques are potentially powerful tools for turbulence measurement in flotation environments, enabling a clearer understanding of turbulence’s influence on flotation performance to be determined.

Jan 1, 2014

By Z. M. Dai

Microorganisms in AMD (Acid Mine Drainage) were enriched in 9K culture medium. The enrichment was applied to leach copper pyrite after the microbial community structure and metabolism was stable. Before and after bioleaching, the microbial DNA was extracted and applied to RFLP (restricted fragment length polymorphism) analysis to demonstrate the relationship between the leaching efficiency and the change of microbial community. Atomic absorption spectrometry results showed that when concentration of the pulp was 10% and pH were 1.5, 2.0 and 2.5, the leaching rate were 56%, 57% and 34% on the 18th day respectively. These results indicated that the rise of pH resulted in the decrease of leaching rate. In lower pH condition, the growth of microbe was faster: when pH was 1.5, the microbial cell number reached to 1.4×107cells/mL on the 9th day; while pH was 2.5, the microbial cell number decreased to 4×106cells/mL. The analysis of microbial community structure showed that Acidithiobacillus ferrooxidans and Leptospirillum ferrooxidans were dominant species before bioleaching (account for 43% and 32% respectively). And after bioleaching, these two species were still dominant when the initial bioleaching pH were1.5 and 2.0. While the initial bioleaching pH was 2.5, the proportion of these two species decreased. These results demonstrated that the initial bioleaching pH would affect the microbial community structure in bioleaching system at room temperature, and this affect could lead to different copper pyrites bioleaching efficiency.

Jan 1, 2014

By H. M. Gao

According to the difficulty of dolomite removal from collophanite,normal-reverse floatation process has been adopted in floatation with the use of highly selective collector G-4 and depressant S721. Good indexes of flotation have been obtained with the run-of-mine ore containing 17.96 % P2O5 and 2.31 % MgO being upgraded to a concentrate containing more than 30% P2O5 and less than 1% MgO. The reagent interaction mechanism in low grade collophanite flotation has been stu-died by FTIR analysis and theoretical calculation. The results indicate that the interaction between collector G-4 and collophanite is the result of chemical adsorption in combination with physical ad-sorption with chemical adsorption playing the major role. Depressant S721 adsorbs on dolomite surface to form a water film and effectively depresses the flotation of dolomite and reduces the MgO content in the concentrate.

Jan 1, 2014