Search Documents

By Tristan Worsey, Nathan Rouse, Daykin Schnell

The authors were retained by a proposed underground metals mine operation to evaluate the potential blast vibration amplitudes that could be generated at surface structures above the proposed mine. Literature reviews of published blasting documentation gave little information, data, or models on surface blast vibrations produced by underground mines. At the client’s request, the authors contacted a number of underground mining operations to evaluate interest in sharing blast vibration data with the authors so that the authors could develop an underground-to-surface blast vibration regression equation.

Feb 1, 2020

By Nikolaos Petropoulos, Changping Yi, Daniel Johansson, Håkan Schunnesson

The effect of jointing on fragmentation by blasting was investigated experimentally and numerically. Firstly the experimental results were presented. Then the numerical modelling based on the experiments was performed. The same conclusions can be obtained based on both experiments and numerical modelling.

Feb 1, 2020

By Corry Goumans

Description of Project: Drilling, Blasting and Installation of Catenary Cables. Project Owner: Rio Tinto Alcan

Jan 1, 2010

"In this work a blasting seismograph was tested on a vibration shaker controlled by a single-point laser Doppler vibrometer (LDV). A total of 43 tests were made to measure the transfer properties(transmissibility and phase shift) of the basic elements of the full monitoring chain and investigate theperformance of the full system. The main elements of the seismograph are described by second ordertransfer functions with typical parameters calibrated through nonlinear fit of the measured responses. The resulting transfer function is used to compare the behavior of the tested seismograph with fourtheoretical seismographs representative of those used in blasting. Fifteen theoretical inputs are runthrough the transfer function of each seismograph to assess their steady-response. The error (expressed as gain) in the peak velocity has been assessed. It varies from -1.5 to 2.3 dB (equivalent to atransmissibility of 0.84 to 1.3, respectively) depending on the seismograph and frequencies of the input.The largest errors occurred for input signals with frequencies in the low (<32 Hz) or high ranges (>125Hz), where the mechanical, electronics and digital parts of the seismograph modify the signals. Seismographs with the nominal transfer function described by DIN 45669:1:2010 are ranked with the smallest errors. Monitoring devices with transmissibility around one in a narrow bandwidth, in line with ISEE suggested criteria for amplitude response, involve large phase shifts at low and high frequencies, resulting in a worst performance."

Jan 1, 2017

By Sedat Esen

"This paper presents a critical review of the fragmentation data obtained from some large open pit copper and gold mines. Database ncludes 35 mines with Uniaxial Compressive Strength values ranging from 19 MPa to 227 MPa (2756 psi to 32923 psi). Variation in the fragmentation data and the causes are discussed in detail. Quality assurance/quality control (QA/QC) in drilling and blasting was shown to have significant impact on fragmentation. In addition, controllable blast design parameters including drill pattern, powder factor, blast timing, stemming length, etc as well as the large blast sizes havesignificant potential to improve fragmentation. Feed size requirements of crushing and grinding circuits were discussed in detail. The paper discusses the effects of different size fractions (top size, 80 %passing size and % passing 10 mm (0.5 in)) on the downstream processes and the role of the fragmentation model in the mine to mill process. Blast domains based on rock strength and structure canbe established by using a fragmentation model which is calibrated using measured fragmentation data. This allows the blast engineer to compensate for changing rock characteristics and stabilize the ROMfragmentation size and result in increased crusher and mill throughput. Two case studies were presented to demonstrate the benefits achieved in downstream processes. Main benefits were reduced downtime at crusher circuits, improved mill throughput as well as reduced total operating cost. A simple relationbetween uniaxial compressive strength and powder factor was proposed using the database for the optimized mines as a guideline to allow site engineers to compare their sites against the other sites."

Jan 1, 2017

By Wilfrid Comeau

Vibrograms, which last significantly longer than the actual blast (say 10 to 15 cycles or more), may be signalling an elastic response, which is not uniquely blast related. For example, geophones mounted on a part of a structure, which can elastically resonate at a frequency included in the seismogram, may not show the structure’s real reaction to the blast. This resonance usually amplifies the ground vibration. This contribution examines one particular case where blasting excited and amplified a resonant ground response, and the method used to significantly reduce or eliminate this undesirable condition.

Jan 1, 2007

By S. Geerts, J Davidson

The purpose of the experiment was to determine detonation characteristics of various improvised explosives. The test consisted of detonating a pipe filled with an explosive compound inside of a plywood arena. The pipe will be located in the center of the arena to ensure even distribution on the witness panels. Details on pipe dimensions, weights of the pipe and explosive, and the density were recorded prior to testing for use in the model calculations. The same size pipes were used throughout to minimize the variables inherent in testing. The plywood witness panels will capture the fragments so that penetration data was obtained, primarily the surface area of impact and depth of penetration. Through the use of the penetration data in conjunction with a mathematical model the original fragment velocity was determined. The mathematical model was developed to measure lethality of fragments from explosives and was modified to determine the original fragment velocity instead. From this model other variables such as the Gurney velocity were calculated. This test was done with an explosive compound that was commonly found, and numerous improvised compounds. In order to guarantee accurate data all of the explosives used for testing were cap sensitive, to eliminate the need for a booster charge which would introduce many unknown variables. The one common explosive compound that was used was C-4 which has known data in order to show accuracy of the model and calculations. The other 5 compounds chosen will not have this data as they will primarily be improvised mixtures.

Jan 1, 2011

By VIVEK KUMAR HIMANSHU, Murari Prasad Roy, Kaushik Dey, Rakesh Kumar Singh, Ashish Kumar Vishwakarma

Sublevel stoping is commonly adopted method in underground hard rock mining. Proper planning and its execution is the key requirement for stope extraction using this method. The stope extraction has been a challenging task since decades. The major reason being the unavailability of free faces as compared to open cast bench blasting. The geological and geotechnical parameters changes gradually even within the stope itself. So the blast design parameters should be planned according to the scenario of upcoming ring. Blast design parameters like burden, toe spacing, inclination of blast holes, diameter of blast holes, charge density of explosive etc plays an immense role in rock damage. For the proper breakage of rock, the movement of burden is prime objective. To study this, explicit dynamic based modeller of M/s Ansys was used. The burden values were varied from 20-65 times diameter to assess optimum burden value during the study. The models were simulated for the rock having 35 MPa uniaxial compressive strength and 102 mm blast hole diameter. Altogether three holes were blasted having hole depth 14-14.5m. The blast design parameters and respective blast induced ground vibration has been measured at the experimental site. Core sample of the rock of experimental site has been used for the evaluation of geotechnical parameters. These geotechnical parameters were inserted into the simulation model. The volume of rock excavated along free face has been calculated in each model. It has been found that the burden value can varies from 35-40 times blast hole diameter (3.6-4.1m) to achieve greater volume of rock along the free face for 102 mm blast hole diameter and rock of 35 MPa uniaxial compressive strength.

Feb 6, 2023

By Barbara Rutter, Shonn Kevin McNeil

"This study discusses how a prototype was built to measure the sonic velocity in powdered explosives.The sonic velocity of an explosive is a benchmark to determine if the explosive deflagrates or detonates;however, little work has been done to determine this value for powdered explosives. This paperdiscusses the results of the initial prototyping tests where two known mediums, air and water, were used for validation. The prototype did record the sonic velocity within the known velocity ranges of air and water; however, a few depths did not fall into this range. This prototype could be used for testinggranular materials."

Jan 1, 2017

By Gregory Hempen, Thomas Keevin, Russell Wilcox, William Wild

The Department of Defense Strategic Environmental Research & Development Program (SERDP) awarded funding for evaluation of procedures to mitigate peak pressures and energy flux density in the water column from ordnance being detonated on the ocean floor. The research purpose was to conduct scaled testing to resolve whether a theoretically-viable covering technology was operationally effective in reducing blast effects and the impacts of shrapnel. An additional objective was testing effectiveness of this method for hard-bottom units (rock or coral) and (unconsolidated) sediment substrate.

Jan 1, 2011

By María Rocha, Benjamín Cebrián, Roberto Laredo

"Ring blasting designs have to achieve different goals in order to become efficient whether is done in up hole or downhole fashion. Ore recovery/dilution control, fragmentation and drift integrity all have to be taken into account when selecting parameters such as burden, spacing, linear explosive density and stemming. Blast energy simulation allows identifying contours of rock breakage and fragmentation, thuschoosing a combination of spacing at the end of holes and appropriate burden. Also, simulations are keyto concentrate energy levels on the mid part of the ring while making sure there is not too high of energy concentration around the drift, which integrity is needed for a safe ore mucking."

Jan 1, 2017

By Tyler Acorn, Paul Worsey, Nathan Rouse

The effect of the hole diameter on vibration attenuation has not been incorporated in most vibration models in the blasting industry. In current vibration models, the charge weight and the distance from the blast are the two primary variables that are addressed. Charge weight is a function of explosive density, charge length, and charge diameter. This geometry-weight can complicate the isolation of the charge diameter variable.

Jan 1, 2013

By P McConnell, T Garrigan

Tara Mines Limited, in Ireland, is Western Europe's largest zinc mine. Annual metal production, from 2.5 million tonnes of ore, consists of 180,000 tonnes of zinc and 34,000 tonnes of lead.

Jan 1, 1989

By Ali Kahriman, Olivio Angelini, Ibrahim Sefer, Burak Ekmen, Koray Arpak, Ertugrul Kaya, Yucel Karakus, Abdullah Sak, Aziz Ozdemir

In recent years, in order to bring solution to traffic intensity arising from transportation problems and facilitate public transportation in the modern world in paralel to urbanization and to the increase in population, it’s well known that, the construction of Access tunnels is inevitable. The driving of the tunnels is a subject of special interest in the technique of rock blasting. The essential factors in terms of tunnel driving and safety in tunnel blasting that is applied in metropolitan areas, an in depth knowledge of ground vibrations and the ways of reducing them to safer levels.

Jan 1, 2010

By Jean-Francois Lagueux, Andre Pomerleau

Goldex Mine is an underground mine located near the town of Val-d’Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long holes stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23.0 M tonne (25.3 M ton) of ore, large blasts up to 1.8 M tonne (2.0 M ton) are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km (0.62 mile) radius of the mine site.

Jan 1, 2011

By Sven-Erik Johansson, Gosta Rundqvist, Donald Jonson

In Stockholm a new road traffic system called Södra Länken (Southern Link) will be in operation in late 2004. The total length of the road system is 6 kilometres of which 4,5 kilometres run through tunnels under suburbs immediately south of Stockholm inner City. The new traffic tunnels together with existing Metro tunnels, which mostly are in rock, will be the determining factor for blast design for many projects in the future. To set reasonable and safe permitted vibration levels the Swedish National Road Administration, Stockholm Region and Stockholm Transport Rail System have together financed a project to determine guide levels for blast-induced vibrations in traffic tunnels in rock. The purpose of the project has been to establish guide levels that are appropriate for different types of rock tunnels.

Jan 1, 2004

By Santiago Gómez, Pablo Segarra, José A. Sanchidrián

In this paper, differences between the industry-standard Holmberg-Persson (H-P) approach and a semi-analytical vibration prediction model called full-field solution (FFS) are analized. The analysis is conducted at two levels: vibrations and rock damage.

Feb 1, 2020

By Tapan Goswami, Brent Geoff

Mining multiple steeply sloping coal seams introduces challenges in terms of safety and productivity. Work on steeply sloping surfaces for the processes of bench preparation, mark-out, drilling, loading and blast tie-up, coal cleaning and recovery is inherently hazardous. Furthermore, a large number of mining cycles is usually necessary, as small rounds are required and each layer is separately drilled, loaded, blasted and excavated. This exposes personnel and machines to additional risks and also incurs higher unit costs of mining as machine productivity is reduced. A case study is presented of a mine in New South Wales, Australia where three coal seams are separated by layers of inter-burden rock. Due to the unfavourable sloping nature of the coal seams the conventional practice was to drill and blast each layer separately.

Jan 1, 2010

By Gary Cavanough

The spontaneous exothermic reaction of ammonium nitrate explosives with sulphide-containing rocks, commonly referred to as reactive ground, is a site-specific condition that can lead to spontaneous detonations. Mine sites typically carry out regular assessment of ground for reactivity. In Australia, reactive ground testing is conducted according to the Australasian Explosives Industry Safety Group (AEISG) Code of Practice. This paper presents a new method to assess reactive ground. The new method can be completed on the mine site or in the laboratory. The new method allows samples to be tested in hours not weeks, as required when using the method prescribed in the AEISG Code of Practice. The new method also provides an explanation of why ground is reactive or not reactive, Whereas the AEISG Code of Practice provides a reactive, not reactive or marginal results with no understanding of reason for these results. Case studies on the use of weathering agents, pH, sulphide content and carbonate content will be reported. These case studies identify instances where the testing as per the AEISG Code of Practice provides false positive and false negative results. A false positive result will require the use of inhibited products when they are not actually required which increases costs and reduces productivity due to the need to used multiple explosive products. A false negative result increases the risk of an unplanned initiation of a blast hole.

Feb 6, 2023

By E. Líder, J. Pavez, J. Rivera

The application of new technologies, methodologies, and the use of new products in mining operations is a practice that is becoming more common in the industry every day, added to the new challenges and restrictions found in the operation. In the city of Tierra Amarilla, the interaction between mining operations and the community presents a constant challenge given the proximity to the community and the limitations that this presents. Explosive charge mass, in conventional blasting using traditional explosives (ANFOs, packaged explosives for example) limits the explosive charge lengths (they are reduced), impacting the explosive charge productivity. To improve the productivity of explosive charge and fragmentation, the use of low-density explosives was proposed, allowing the increase of the explosive charge length, trying to maintain the vibration levels within the established limits (2mm/s), preserving the fragmentation of the rock in the required sizes. The present study shows the results obtained from the application of low-density bulk emulsion for production blasting charges using upward and downward fan drillings. During this process, 18 blasting events were carried out, of which 8 were Up-hole loading (average density of 0.75 gr/cc) and 10 with Down-Hole loading (average density of 0.95 gr/cc). In summary, a total of 110,760 tons of ore have been broken, using low density emulsion, meeting the proposed objectives such as: 33% reduction of vibrations, 12% overbreak (within the theoretical design), P80 of 11in and 4.6% in fines.

Jan 1, 2024