Search Documents

By Robert Hopler

THE KEYSTONE NATIONAL POWDER COMPANY is an Independent organization, incorporated under the laws of the State of Pennsylvania. It has three dynamite mills near Emporium, Pa., with a daily capacity of 165,000 pounds. It maintains branch offices in practically all the largest cities east of the Rocky Mountains, and has distributing magazines located in every section where there is a demand for high explosives, with facilities for wagon deliveries. Our mills are all of modern type and are equipped with the most improved machinery for the manufacture of high explosives. The efficiency of our laboratory in conjunction with the high class of labor employed, has enabled us to put on the market an explosive, the quality of which is the result of extensive research and scientific knowledge. Our modern and complete equipment for harbor and railroad transportation insures our patrons of prompt deliveries, which is an essential feature particularly to contractors and those whose facilities for storage are limited.

Jan 1, 2013

By Chris Vagasky

On July 10, 1926, lightning struck at Picatinny Arsenal, New Jersey, and caused the explosion of at least 600,000 pounds (272,000 kilograms) of ammunition, resulting in more than $600 million (2015 dollars) in damage, the destruction of 200 buildings, and 22 deaths. Fortunately, there has not been a major incident involving lightning and explosives in the US in some time, though lightning has destroyed fuel storage tanks in recent years, including in North Dakota, Texas, and Ohio. Lightning poses a significant hazard to the explosives industry. Carrying high currents and temperature, lightning can cause explosives to detonate, start fires near storage facilities, and injure or kill operators.

Jan 1, 2017

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"The urgent need for improvements in the control and mitigation of environmental and social conditions associated with the extraction and processing of raw materials is increasingly a demand imposed by legal entities and institutions. Therefore, this present article proposes an improvement of the estimation in the magnitude of the vibrations resulting from rock blasting methodologies in the surrounding areas,incorporating the heterogeneity caused by uncontrollable parameters, such as geological andgeotechnical characteristics. This methodology combines the use of empirical vibration attenuation lawscommonly known and with terrain discretization techniques using Voronoi’s decomposition. For thevalidation assessment of this methodology, the data set collected and compiled is composed by 87 vibration measures collected in 16 sample points in one area of study of which 2/3 of the samples were used to create the model and 1/3 for the validation. Using normality tests for statistical residue analysis,it is possible to infer that this present model has null residual mean, as well as a smaller sum of residualerrors. Comparing the methodology present in this paper with the procedures executed nowadays, areduction of the errors associated with the estimation is obvious, highlighting a better characterization of the behavior of the vibrations associated with rock blasting."

Jan 1, 2017

By Mark Spaniel

Computer 3D modeling to evaluate the potential underground blasting fragmentation performance based on rock within calculated damage radii along drillholes, as well as the burden distance from explosives along each drillhole. The results estimated from the 3D computer models closely predicted results found in the real world testing.

Feb 1, 2020

By Joe Atalla, Jesse Desrochers, Rodrigo Hayashida, Joseph Mukendi Kabuya

The Mont-Wright mine stands as a prominent open-pit operation in Canada, renowned for its vast iron-ore reserves. However, the efficacy of its blasting operations, crucial for efficient production, has encountered challenges due to the diverse lithological compositions across multiple pits. This study presents a comprehensive approach to optimize blasting practices at Mont-Wright mine, tailored to the specific lithological characteristics of each rock domain. Through systematic analysis and experimentation, blasting guidelines were meticulously developed, aiming to enhance grindability and equipment productivity. The implementation of these guidelines promises significant improvements in operational efficiency and resource utilization, positioning Mont-Wright mine at the forefront of sustainable iron-ore extraction.

Jan 21, 2025

By Robert Hopler

BH Note: This price list stresses the point that the number six strength cap should be used with all high explosives. It’s interesting that duPont chose to continue to supply the lesser strength caps – but lowered the price of the #5 or #6 to be closer to that of the #4 and #3. There were imports of the lower strength caps at the time that had to be competed against, hence the price reductions. Another interesting point on this price list is the noting on the “Red Cross Explosives” page that these explosives reduce the danger incurred during the operation of thawing. As noted many times in these articles, this problem was not to be solved for about another 16 years or so.

Jan 1, 2011

By Zhiwei Jiao, Ziqing Guo, Mushen Wang, Yueda Fang, Qiuming Tang

In order to achieve anti-terrorism, production safety, better explosive performance, lower cost, and environment protection, we developed HMS (emulsification in borehole).Long-process PM (plant-mixed) and SM (site-mixed) emulsion trucks are reviewed and compared to a new type of short-process HM (hole-mixed) truck for onsite emulsion manufacturing. The short-process HM truck has demonstrated many advantages over its PM and SM counterparts in areas such as process safety and security, energy efficiency and environmental impacts: 1) No emulsion matrix is manufactured in the plant, transported on public roads, or even present on the surfaces of blasting job sites. Such characteristics are certainly beneficial in eliminating risks of the product being diverted and used by unlawful players; 2) This short-process involves "micro-fluid control to form super oil phase-rich" in tubular emulsification process, making it intrinsically safe; 3) There is basically no residual matrix left in the truck or on the job site to clean up, which greatly reduces environmental impact of the process; 4) Comparing with typical PM and SM trucks, the HM truck has eliminated the needs of many power equipment and critical pump pressure for turbulent flow forming a static emulsification with super oil phase -rich is only 0.2Mpa. These is therefore quite energy efficient.

Feb 1, 2020

By Italo Onederra, Miguel Araos

Most of the current explosives for mining blasting activities rely on voids to become sensitive to initiation, then detonating and finally, sustaining that detonation. The use of voids is known as hot spot sensitisation. Various forms of voids serve as hot spots – gas bubbles (predominantly in bulk explosives), glass (or plastic microballoons, for packaged products), or expanded polystyrene (bulk explosives). Gas bubble sensitisation uses the decomposition of sodium nitrite to produce nitrogen gas bubbles, which are dispersed throughout the bulk explosion. These gas bubbles, when hit by a shock wave (such as from a booster), compress and heat up, subsequently decomposing the explosive and releasing energy to sustain the detonation. It has been suggested that the use of different types of gases to create voids in non-ideal explosives could offer some alternatives to the sensitisation process, which could be reflected in the change of the detonation properties of the explosive. The reason would be that each gas has a different ratio of specific heats (=/), and when these gas bubbles are compressed, they will heat up to different temperature, affecting the decomposition of the explosive and thus, the VOD.

Jan 26, 2026

By Ricardo Dr. Chavez, Mathieu Lachamp, Rob Dr. Farnfield

Pueblo Viejo is an open pit gold mine in the Dominican Republic which is always looking forward to implement the newest technology in the industry to improve all processes. Focusing on one of the pillars of the department and our company, digitalization, we’ve been looking for the technologies that allow us the automation of data generation, supervision and process innovation. That’s where a new Drill and Blast software takes place, helping to integrate the process from the beginning to end, right after the pattern is designed until it’s blasted, allowing us to track results like vibration, fragmentation, performance, cost and inventory of each blast in a single platform. The software helps engineers to generate back analysis by blast, bench, pit, month and many other ways, in a timely friendly manner. Therefore, we can catch business opportunities and improvement for the drilling and blasting process.

Jan 1, 2019

By Robert Hopler

209. Nitro-glycerine is produced by the action of nitric and sulphuric acids on glycerine, and is a heavy liquid of oily appearance, of specific gravity about 1•6, varying from colourless when quite pure to a yellow or brownish yellow. It is of a very sweet taste, and without odour, and is an active poison. Mere handling of it will in most persons induce sickness and headache. It explodes when heated to about 360° F. or from shock, but in small quantities it ignites and burns with some difficulty by the mere contact of flame.

Jan 1, 2011

By Ruilin Yang

This paper provides a theoretical analysis of shockwaves in an air-deck induced by detonation of an explosive charge and shows that the initial shock pressure in the air-deck at the interface with the explosive charge is only about 1% of the detonation pressure. A rarefaction wave with the low pressure travels back into the explosion detonation products greatly reducing the post-CJ detonation pressure. Additionally, AUTODYN modelling shows that the pressure attenuates further during shockwave propagation along the air-deck. Although the pressure increases at the bottom of the blasthole due to shock reflection, the overall pressure in an air-deck does not increase and is still around 1% of the detonation pressure which is too low to break most rock.

Jan 1, 2016

By Stephen Mansfield

In metalliferous mining operations, subdrill is that portion of the blast hole that is drilled below the target grade elevation, and in most cases loaded with explosives. Its primary aim is to enable efficient excavation down to the target floor level. Subdrill is often described as being expensive and that excessive subdrill should be avoided, as it can result in damage to the subsequent floor, lead to difficult drilling conditions and higher vibration levels. As a result, many operations aim to apply the bare minimum amount of subdrill in order to excavate to the target floor

Feb 1, 2020

By D J. McLane, J T. Rathbun, B T. Lusk

The dynamics of explosive detonations are understood, however recreating a real-world, full scale scenario is costly. The use of a shock-tunnel allows testing to be done on a smaller scale, with the simulated effect of a large explosion. Analyzing explosive waveforms using this method can greatly reduce cost in testing blast resistant products, such as anti-terrorism devices, mine safety products, and military equipment. The purpose of this paper is to better the understanding of how the waveform characteristics resulting from an explosive detonated within a shock-tunnel differ from those in an open-air arena test. The variables of comparison between an open-air arena test and those conducted within a shock tunnel are peak pressure, impulse, shock wave velocity, and cross sectional shape of the shock front. Understanding how these variables differ, tests utilizing a shock tunnel can be conducted with a higher degree of accuracy and repeatability.

Jan 1, 2013

By Allen Kinney, P. T. Freeport

This paper presents the methodology for final wall-controlled blasting utilized at the Grasberg Mine. The resulting optimized slopes representa14%and17% increase to bench face angle (BFA) and inter-ramp slope angle (ISA), respectively. The corresponding increase in both copper and gold recovery was more than 40% greater than forecast for each material. The Grasberg open pit mine is located in the remote jungle province of West Papua Indonesia, at an elevation of 4,200 meters(13,780 ft).With a diameter of approximately 3.5km(2.2 mi), anddepthover1.2km(0.7 mi),P.T. Freeport Indonesia (PTFI)has mined billions of tons of rock from one of the world’s largest gold and copper deposits. Grasberg Operation and Engineering implemented a quality driven slope optimization program for the final pushback, with the goal to safely increase recoverable metal through steeper slopes, while utilizing existing infrastructure and equipment. This paper focuses on controlled blasting initiatives, blast monitoring, and as-built slope measurement tracking, although many groups contributed to the success of Grasberg slope optimization. The potential slope optimization area was divided into two sections based on geologic assessment: Area A at radial 200°-270° and Area B at radial 270°-360°. Original slope designs for areas A and B specified ISAs of 51° and 52°, respectively, with all BFAs in the pit at 70°. Through continuous development, collaboration and achievement, the Grasberg final pit accomplished a BFA increase to 80°for all areas, and an ISA increase from 51° to 56°in Area A, and 52°to 60° in Area B.

By Dirk Voogt, Quentin Steyl, D. Scott Scovira

A South Africa iron ore mine reported a decline in blast performance and ore and waste fragmentation. Preliminary investigation by the explosives services company found that the straight gassed bulk emulsion was breaking down and collapsing inside of some loaded slept blastholes. The bulk emulsion loaded at the subject site was manufactured in country and shipped to various clients throughout the region, with normal function in blasts at other sites. Historically, the bulk formulation emulsion being used at the subject mine site also performed well and without issue. This raised the question, “why is this bulk emulsion now breaking down and not firing in blastholes?”. Iron ore mines are not typically associated with reactive or acidic ground, and ground sample reactivity testing against the emulsion confirmed this. So, if not reactive ground or acidic water, then what is causing the emulsion to breakdown?

Feb 6, 2023

By Karl Peterson, Bibhu Mohanty, Chanakya Nariseti

The mechanism of crack formation in two target rocks (Kuru granite and Flamboro Limestone) is studied experimentally by simulating the impact action of a percussive drilling bit. Rock samples are dynamically loaded using a custom made impacting bit (8 mm, 12 mm and 15 mm diameter bits). The target rocks are impacted at velocities 8, 10, and 12 m/s. The resulting crack patterns are visualized by three techniques, Dye penetration, CAT scans and Optical scans. Mapping of the crack patterns is manually done with Photoshop. For 3D damage visualization, the crack patterns are mapped in two planes (impact surface and longitudinal sections). The three techniques are compared to determine an optimum technique for better damage visualization. The evolution of crack pattern with impact velocity and bit diameter is discussed.

Jan 1, 2015

By Carlos Campos Junior, Leonardo Soares Chaves, Raul Carretero Hoz, Renato Jacome Costa, Davi Bastos Martins de Oliveira

The Vale’s Serra Sul mine, also known as S11D project, is one of the world’s largest open pit iron ore mines, located in Brazil’s Amazon region. The mine produces around 90 Mt of high-quality iron ore annually. Its unique orebody enabled the S11D project to adopt a truckless mining system with In-Pit Crushing and Conveying (IPCCs) for ore exploitation and waste stripping. The IPCCs system requires crushing the waste, mainly composed by the jaspilite lithology, and is also conveyed to waste deposits several kilometers away from the mine. Due to Amazon’s environmental restrictions, the project was designed with preliminary geological knowledge, leading to the installation of primary crushers not designed for the hardest jaspilite, with uniaxial compressive strength (UCS) up to 500 MPa. This resulted in low waste crushing performance, affecting stripping ratio and threatening future production. A project was developed to improve the fragmentation of the jaspilite, allowing higher waste IPCC production, and reducing the risk to the production due to low performance of waste crushing and conveying. The first challenge was the independence of the geological and the geomechanical models, while only the geological model was considered in blast designs, the geomechanical model describes six waste groups of jaspilite classified according to their strength. A new geological model was then created to incorporate the geomechanical classification, allowing different blasting design according to the rock strength of the jaspilite. The blasting pattern on most compact jaspilite was reduced 27%, from 22m² to 16m² in 9 7/8” diameter holes, with a proposed theoretical reduction of 23% of the P80, from 326mm to 250mm. The second challenge was the implementation of the new design, as this pattern size and the high powder factor (2.9 kg/m3) were paradigms for such a large iron ore mine. The measured results have shown 25% reduction of the P80, the crushing rate was increased by 17% (230t/h), saving around $2.4 million annually in crushing and conveying system maintenance.

Jan 21, 2025

By Tristan Worsey, Jhon Silva

The paper discusses a limestone quarry case study that looks at change in fragmentation due to using different charge sequences when using the regular rhythmic timing method.

Feb 1, 2020

By Brian Sandhuas, Robert McClure

All flyrock incidents have the potential to result in injuries or fatalities that can result in loss of company reputation, license to operate with clients, and bear the exposure to high cost liability. From 2007 to 2009, one North American Quarry and Construction Business experienced a series of flyrock incidents. In the spring of 2009, this business declared that the frequency and severity of Flyrock Incidents had reached an unacceptable level. A Flyrock Elimination Program was launched.

Jan 1, 2012

Dear All, I am looking for information about vibrations and effects on fish in pools. A tunnel blast is planned to be carried out as close as 300 meters to a freshwater fish growing plant. What is the vibration criteria for fishes in pools? Your comments will be highly appreciated.

Jan 1, 2012