Search Documents

By Kihong Park, Matthews C. Habjan, Arthur L. Miller

New Mining Safety and Health Administration (MSHA) regulations limit the mass concentration of airborne diesel particulate matter (DPM) or, more specifically, the concentration of elemental carbon (EC), in underground mines. The mine operators are responding by introducing a variety of controls to reduce DPM in the mines, potentially including the evaluation of new maintenance procedures to reduce underground mine vehicle emissions. There is currently a lack of an inexpensive and dependable method to directly measure the DPM concentration emitted from the vehicle tailpipe. To that end, this work demonstrated a simple field portable method for estimating the mass concentration of elemental carbon exiting the tailpipe of a diesel engine using a direct reading photometer. Simultaneous measurements of tailpipe exhaust were made with a Thermo Electron Personal DataRAM 1200 photometer (particulate mass concentration based on light scattering) and by analyzing PM2.5 and PM1.0 samples collected on quartz fiber filters using the National Institute of Occupational Safety and Health (NIOSH) method 5040 (mass concentration of EC via thermal-optical method). Results indicate surprisingly good correlation (R2 ) 0.97) of the two methods when the data are adjusted for relative humidity (RH) and corrected using an empirically generated calibration factor. Although preliminary, it may be possible to implement this method in maintenance shops to monitor emission trends and to compare emissions of various vehicles in a fleet. Such data will be useful for fleet planning to meet new air quality standards.

By J. W. Paul

The United States Bureau of Mines has made a study of roof control in 68 mines operating in the Pittsburgh coal bed in Pennsylvania, West Virginia, and Ohio. In making these studies, much information was also obtained on various exact methods of development and pillar extraction as practiced by this large group of mines. It is proposed in this paper to describe these methods, by which this group of mines in 1931, a year of reduced industrial activity, produced 28,123,000 tons of bituminous coal - 7.4 percent of the national production for the same year and an amount equal to the combined production of the coal mired in the States of Alabama, Colorado, New Mexico, Utah, and Wyoming. The results of these studies, insofar as they pertain to the prevention of injuries from falls of roof, have been published by the Bureau of Mines. In this paper only a few mines typical of each system will be described; however, should the reader be interested in other details with respect to these mines, he may refer to the following publications: T.P. 522, 1932, 43 pp. Falls of roof and coal in mines operating in the Pittsburgh coal bed in Marion and Monongalia Counties, W. Va., by J. W. Paul and J. N. Geyer.- A study of nine mines in these two counties of northern West Virginia.

Jan 1, 1935

By P. M. Daling

This report, sponsored by the U.S. Bureau of Mines, presents the results of an examination of the safety of the impactor shaft sinking system in comparison to conventional shaft sinking technology. Detailed study of the impactor system was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the impactor machine and its support systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates measures of both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the impactor shaft sinking system was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that the impactor shaft sinking system is safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by an average of over 35 percent with use of the impactor shaft sinking system. Design change recommendations to further improve the safety of the impactor system include a revised fire suppression system, improved access to and from the operator cabs, reliable noise attenuation measures, and improved communication systems. An operational safety manual was also developed for the impactor shaft sinking system.

Jan 1, 1982

The annual reports of the supervising engineers of the seven sections comprising the Mining Division are assembled in the following pages and constitute the annual report of the division. In planning activities, the aim has been to adapt the work to changing conditions and needs of the mining industries and to avoid becoming bound to any particular type of investigation when others are found to be of more pressing interest.

Jan 1, 1939

By Richard L. Ash

Introduction The blasting capabilities of commercial explosives are often rated according to their loading densities and detonation velocities. Both the density and velocity are relatively easily measured, the values of which can be used for determining the approximate detonation pressure developed by an explosive during any given set of blasting conditions (1-5). Knowledge of the actual rate of detonation attained at all points along a charger's length also is considered to give a good indication of how well the explosive is functioning. Many factors affect the density and velocity and have been thoroughly discussed by various authors (4, 6-12). For recording velocities several methods are available, but the resistance-wire, or probe, continuously recording technique has the distinct advantage of providing a record of the complete progress of an explosive reaction from the time it first initiates. Figure 1 is a copy of a typical record obtained by the procedure with certain significant information indicated. The theory and applications of the method are extensively covered in the literature so need not be reviewed for this report (13-18). Only the specific equipment and procedure employed for this investigation are presented.

Jan 1, 1973

By F. G. Scott

This document is a proposed program plan for mining environmental research to be conducted by the U.S. Bureau of Mines in support of industrial oil shale mining and processing. This program plan is one of three research alternatives being considered by the Bureau, each based on a different level of anticipated funding. This report documents the mid funding level program plan.

Jan 1, 1980

By J. R. Thoenen

In the summer of 1937 the authors began a series of time studies of the various processes employed in' the production of crashed stone. These studies, made at quarries situated in the eastern and southeastern parts of the United States, have not been completed, but to make results available to the industry as early as possible, it was decided to publish summarizes of the studies made to January 1, 1939, as a series of progress reports. The first of these dealt with power-shovel loading and was issued as Report of Investigations 3461 in September 1939. The second, issued in September 1939 as Report of Investigations 3467, dealt with quarry haulage. The present report discusses analyses of time studies of primary drilling a t the same group of quarries. OBJECT OF STUDY Pressure of business problems frequently requires the entire attention of quarry management, and in consequence internal plant economies often are neglected. Also, operating officials absorbed in their local problems are prone to overlook possible economies that would attract attention immediately were they critically examining another plant. The authors felt that technical studies at a number of plants, made by impartial engineers, might disclose opportunities to reduce costs or improve efficiency in internal plant processes.

Jan 1, 1940

By E. E. Ungar

Criteria applicable to noise in coal cleaning plants are presented, and the generally applicable noise control principles and approaches are discussed. The operating characteristics and equipment of coal cleaning plants are described. Considerations entering in the selection and design of noise control means are delineated, and specific means for equipment noise reduction are described. The limited utility of acoustically absorptive materials in plant spaces is indicated, administrative means for reducing worker noise exposure are pointed out, and ear-protective devices are described briefly. The reduction of plant noise reaching nearby communities is discussed. Programs leading to quieter machines an coal cleaning plants are suggested.

Jan 1, 1974

By Maurice C. Fuerstenau

The kinetics of leaching galena with ferric chloride and ferric nitrate have been examined as a function of ferric concentration, salt concentration, temperature and particle size. Diffusivity of ferric complex ions was also established as a function of ferric chloride concentration and temperature. In the presence of 3 M NaCl, leaching rate is controlled by product layer diffusion when ferric chloride is added as oxidant. With NaCl concentrations less than 3 mole/liter rate decreases with decreased NaCl concentration, and, thus, rate is apparently not controlled by product layer diffusion. It is suggested that rate is controlled by lead chloride solubility at the reaction interface under these conditions. When ferric nitrate is added as oxidant, leaching rate is limited by chemical reaction control. An electrochemical model is presented. Activation energies are 8.1 and 11.3 kcal/mol in the ferric chloride and ferric nitrate systems, respectively.

Jan 1, 1984

By S. Gallagher, A. G. Mayton

Back injuries account for a high proportion of lost workdays in the mining industry and are a leading cause of disability in mine workers. Two risk factors for low back injuries are manual lifting and whole-body vibration exposure when operating mobile equipment. Recent research has shed light on possible mechanisms through which low back injuries may occur, and the results of these studies can be used to improve the design of lifting tasks and seats to decrease injury risk. This article discusses recent research results and how this knowledge can be leveraged to reduce the risk of low back pain.

The mineral industry of Benin contributed less than 1% of the 1977 gross domestic product (GDP), which was estimated at $500 million.' Other than limestone and salt, no exploitable mineral deposits have yet been discovered in Benin, which has been rated by the United Nations as one of the world's least developed nations. In 1977, the economy was further weakened by petroleum price increases and severe drought. The country continued to depend on foreign assistance, which averaged $20 million per year, to finance development projects. The country's first 3-year plan, which was put into operation in October 1977 after many delays, allocated more than $1 billion to projects in infrastructure, agriculture, and light industry. The most important infrastructure project was the expansion and modernization of the port of Cotonou, valued as an entrepôt port for the transit of goods to the neighboring countries of Niger and Nigeria. Plans called for an increase in handling capacity to 1 million tons of cargo annually, the improvement of port and cargo handling operations, and the upgrading of the efficiency of the Port Autonome de Cotonou (PAC) management system. The $46 million project was to be financed by a consortium led by the International Bank for Reconstruction and Development (IBRD) and including Canada, France, Nigeria, and Abu Dhabi. Construction was scheduled to begin in 1978 and be completed in 1980.

Jan 1, 1981

By Kenneth H. Johnston

The Weber pool in Washington County, Okla. (fig. 1), covers an area extending from 2 miles east and slightly north of Bartlesville, Okla., to a point approximately 2-1P tiles northeast of Dewey, Okla. The pool is a part of the area designated by the Standing Committee on Oil Field Nomenclature, Kansas-Oklahoma Division, Mid-Continent Oil & Gas Association, as the Bartlesville-Dewey field. In the following discussion of the geology, development, and exploitation of the Weber pool, the writers, by means of structure maps, cross sections through various parts of the reservoir, and tabulated development data and production statistics, have recorded salient information on a field that was developed before .1910 in an Area that has been repressured since 1926. The total oil production to January 1, 19.0., from the 2,639 developed acres considered in this report, was approximately 14 million barrels, or a recovery of about 5,3;2 barrels per acre, or 227 barrels per acre-foot. The production of the estimated 18 million barrels of recoverable oil remaining in the Bartlesville sand reservoir will require the initiation of additional secondary-recovery practices on some of the leases and the application of a more systematic repressuring program on others.

Jan 1, 1950

This report presents the results of a study of Kennecott Copper Corporation?s Chino leaching dump at Santa Rita, N. Mex. The stability studies described herein were performed on only one cross section of the leach dump, utilizing data obtained from drilling, sampling, and testing, which was limited in nature. The first part of the report contains a discussion of site geology and seismicity, pertinent information on the waste material disposal system and leaching method, a discussion of the waste embankment characteristics, a summary of the engineering analyses, and a bibliography. The second part (appendices) contains basic geologic and engineering data supporting the discussions in the first part.

Jan 1, 1974

By Bryan Buchholz, N. Kumar Kittusamy

Previous studies indicate that operators of heavy construction equipment are afflicted by musculoskeletal injuries of the arms, shoulders, neck, and lower back. These injuries appear to be due to excessive periods of sitting (static posture), work intensity, whole-body vibration, high resistance levers, repetitive motions, and awkward postures. (2-5) Although numerous studies have shown an association between operation of heavy construction equipment and symptoms of musculoskeletal disorders, very little research has been performed that systematically characterizes operating engineers' exposure to ergonomic hazards. The objective of this study was to systematically characterize the ergonomic hazards associated with excavating operations. As such, the following were performed: (1) vibrations were measured at the operator/seat interface (X, Y, and Z axes), and at the floor of the cab (Z axis); (2) psychophysical ratings of whole-body vibration (WBV) level and overall seat design were obtained; and (3) postural assessments of the job were made. Methodology This study evaluated an inexperienced female operator performing excavation, utilizing two different pieces of equipment. The operator was 37 years old, 162 cm tall, and weighed 80 kg. She had approximately 15 hours of operation time (experience) on the equipment evaluated. The two pieces of equipment used were: a Case Super 580E (1986) backhoe/loader, and an Insley H-2000 excavator (1975) (see Figures 1 and 2). More evaluations were performed on the backhoe/loader than on the excavator. The following evaluations were performed on the Case equipment: 1) vibration levels at the seat and floor; 2) psychophysical ratings of the overall seat design and vibration levels (for the task duration, and for an 8 hour duration); and 3) postural assessments. For the Insley equipment, all of the evaluations were performed except vibration measurements. When the evaluations were conducted, the following environmental conditions were noted: the temperature was 31°F, and soil and terrain conditions were rough and frozen.

Productivity in underground metal and nonmetal mines is contingent upon work methods, mine layout, and ore handling techniques. One of the most important factors impacting productivity is the efficient movement of men, materials and supplies from the surface into and throughout the mine. Various transportation systems such as man-trains, service shafts, rubber-tired diesel equipment, etc. are currently used to transport men and supplies in underground mines. In many underground mines, it is not uncommon for a worker to spend 25% of his eight-hour working day traveling from the surface to his work area and returning to the surface.

Jan 1, 1975

By V. E. Edlund

As part of a research program for recovering alumina from domestic nonbauxitic resources, the Bureau of Mines investigated a lime-sinter, caustic leach technology for anorthosite. This report discusses the unit operations--feed preparation, sintering, and leaching. Acceptable pellets for the bench-scale sintering studies were prepared from mixtures of minus 200-mesh anorthosite and limestone using water alone as the pelletizing agent. Heating pellets at 1,270° to 1,360° C for periods of 0.5 to 2 hr, followed by a 15-min soaking period at 700° C and cooling to room temperature, produced a sinter that dusted to more than 90 pct minus 65 mesh. The weight ratio of limestone to anorthnsite was critical in producing sinter exhibiting good dusting and leaching characteristics. A ratio of 2.0 was optimum for the bulk samples of anorthosite and limestone used in this research. Leach solutions from lower ratio sinters were unstable; gelation became progressively more severe with higher ratio sinters. Leaching the dusted sinter with 10-pct Na2CO3 at 60° C extracted 85 to 90 pct of the alumina in a product solution containing about 50 g/l A1203. Leach residue in contact with pregnant solution tended to set up as a rigid gel as a result of cementation, comp action, and gelation. The presence of a calcium-sodium zeolite [(Cn,Na2)6?(Al2Si04)12?27-3OH20] in the ungelled residues seemed to be the main difference between gelled and ungelled residues.

Jan 1, 1982

By William R. Wayment

The objective of this investigation was to obtain data on friction-head losses of sand slurries during their transport in pipelines. The data ultimately will be used in designing hydraulic transport systems. Information that was incidental to the primary objective was gathered on degradation, changed percolation characteristics, and critical velocities of the slurries~ Tests were made in a closed-circuit pilot plant, with one type of tailing, through horizontal 2-, 3-, and 4-inch-pipe test sections at various pulp densities and flow velocities. Tests were made in a closed-circuit pilot plant, with one type of tailing, through horizontal 2-, 3-, and 4-inch-pipe test sections at various pulp densities and flow velocities. Approximately 2,000 tests were run in the pilot plant. The ranges of flow velocities used in the experiment were 2.8 to 19 f.p.s. in the 2-inch line, 4 to 14.5 f.p.s. in the 3-inch line, and 4 to 11 f.p.s. in the 4-inch line. Velocities were varied in increments of 0.5 f.p.s. through the entire velocity range in each pipe size. Densities were varied in 3-percent increments from 40 to 70 percent solids by weight except for one series of tests in the 2-inch line; in this series, densities were varied in 5-percent increments from 5 to 65 percent solids by weight.

Jan 1, 1962

By Frank G. Horino

Drill cores from 18 exploratory holes that were drilled into the unleached saline beds were tested for mechanical properties by the Bureau of Mines. Test cores were primarily selected from zones L4B, R4B, L3, and R3A in the Piceance Creek Basin, Rio Blanco County, Colo. Regression analysis techniques were tried in an attempt to relate kerogen yield or apparent specific gravity to the parameters compressive strength, Young's modulus, and Poisson's ratio. Correlation coefficients were very poor, indicating that this type of analysis was not amenable to these data. Analysis of variance techniques were tried using a division of either greater than or less than 10% nahcolite together with the requirement of less than 3% dawsonite. Results showed that a larger percentage of nahcolite tended to lower the compressive strength and to increase Young's modulus. A second analysis was made using a division of less than 3% dawsonite and greater than 3% dawsonite together with the requirement of less than 1% nahcolite. For this analysis, a larger per-centage of dawsonite tended to increase compressive strength, Young's modulus, and Poisson's ratio. Mean compressive strength values were determined for the mining horizons of interest. Average physical properties for design purposes were also determined for the horizons of interest and for a proposed adit based only on logged geologic depths to these horizons. No consideration was given to percentages of nahcolite and dawsonite. Creep data obtained from nahcolite-and dawsonite-rich oil shales provides a best fit to a modified power equation.

Jan 1, 1978

This Bureau of Mines report concerns two subjects important in the application of electric power in mining systems. Electrical transients and their suppression are discussed, and several considerations are explored with regard to the use of explosionproof or other electrical enclosures.

Jan 1, 1979

By Gregory M. Molinda

The Coal Mine Roof Rating (CMRR) was developed 10 years ago to fill the gap between geologic characterization and engineering design. It combines many years of geologic studies in underground coal mines with world-wide experience with rock mass classification systems. Like other classification systems, the CMRR begins with the premise that the structural competence of mine roof rock is determined mainly by the discontinuities that weaken the rock fabric. However, the CMRR is specifically designed for bedded coal measure rock. Since its introduction, the CMRR has been incorporated into many aspects of mine planning, including longwall pillar design, roof support selection, feasibility studies, extended-cut evaluation, and others. It has also become truly inter-national, with involvement in mine designs and funded research projects in South Africa, Canada, and Australia. This paper discusses the sources used in developing the CMRR, describes the CMRR data collection and calculation procedures, and briefly presents a number of practical mining applications in which the CMRR has played a prominent role.

Jan 5, 2007