Search Documents

By L. C. IlsLey

"During the last eight years there has been a noticeable increase in the use of permissible equipment in gassy and dusty coal mines. This trend has undoubtedly been toward greater safety in mining, but in spite of this all is not well ""along the front.""In many mines those in charge, either through ignorance or supposed economy, have neglected to install sufficient copper and maintain good bonding on the rails used for return circuits to have a safe working voltage for the permissible equipment which is intended to afford them safety.Low voltage, when properly analyzed, is not economy but frequently is an expensive oversight. Burned-out armatures, controllers, rheostats, and switches are costly in themselves to repair or replace, but the greatest cost in many instances is the loss of production resulting from idle and broken-down equipment.From a safety standpoint, excessive low voltage where permissible equipment is necessary is almost criminal negligence. A burn-out of any kind is liable to cause an arc that may burn its way through a casing wall and bring about a hazardous condition if gas or dust in explosive proportions should be present. Again, all wiring, both interior and exterior to the apparatus, is subject to the extra heating consequent upon low voltage. It should be remembered that if the voltage drops the current must increase a corresponding amount in order that the same work may be accomplished; and as the heating effect is as the square of the current, an enormous overheating of the electrical parts and wiring often takes place. This heating effect is especially detrimental to trailing cables used on portable equipment, because under the most favorable conditions the size of cable selected is only barely sufficient to do its work properly at a safe working temperature; therefore, when the extra current load is added because of poor voltage, overheating is sure to result, with consequent deterioration of the insulation, This effect greatly increases the liability of cable failures in service, and in turn adds to the hazards incident to the use of portable equipment of the permissible type involving the use of trailing cables.Some manufacturers have tried -to protect their equipment from low voltage, especially below a certain point, by -installing low-voltage relays which will trip when the voltage falls to a predetermined value. It is understood that some operators have hesitated or refused to install such low-voltage protection because they were aware that the voltage conditions were so poor that the equipment could not operate under the safe limits set. It is difficult to understand how any progressive company that is willing to go to the ex-pense of installing permissible equipment could be so shortsighted in this phase of common sense, safety, and economy."

Dec 1, 1929

By James L. Ash

This report contains the results of a technical and economic evaluation of conceptual systems for the underground mining, rubblization; and in situ retorting of deep oil shale deposits. Study efforts were first directed towards evaluation of the applicable geology, associated minerals, rock mechanics, in situ retorting, access mining, ventilation, rubblization, safety, and environmental impact factors. Conceptual systems were synthesized and then evaluated against these factors from both a technical and limited economic viewpoint. The results of these evaluations were then analyzed 'and, based upon this analysis, the following two systems were selected for further study: System II: Room and Pillar-Vertical Drill and Blast System IV: Tunnel Boring-Horizontal Ring Drill and Blast Due to the large number of variables to be considered, a computer program was developed and utilized to provide data for the cost trade-off studies and economic analysis. Results of the early computer runs indicated the value of the tool available in the computer program and led to an extension in the contract to determine the sensitivity of the systems to several of the more apparent significant variables. These results in turn led to a refinement in the design assumptions and a better understanding of the technical and economic options available to an owner-operator of a Vertical Modified In Situ Shale Oil Extraction System. This report is submitted in fulfillment of the requirements of Contract Number S0241073 by Fenix & Scisson, Inc. to the Denver Research Center, United States Department of the Interior, Bureau of Mines. Work was completed as of November, 1976.

Jan 1, 1976

By E. A. Mihok

A pilot plant for treating mine drainage by neutralization with limestone was designed, fabricated, and operated by the Bureau of Mines. The process consists of (1) producing a very fine (minus 400-mesh) limestone slurry, (2) mixing the slurry with the mine water, (3) aerating the resulting mixture to remove carbon dioxide and precipitate iron, and (4) separating the solids from the liquid by sedimentation. A mine discharge of pH 2.8, containing 1,700 ppm total acidity, 36 ppm ferrous iron, and 360 ppm total iron, was treated at rates from 300 to 400 gpm. The treated water ultimately reached a pH of 7.4 and contained no detectable iron. The resulting sludge compacted to approximately one-third the volume of sludge from mine water neutralized with lime. The advantages of the limestone process, compared with the conventional lime process are as follows: Widespread distribution and lower cost of run-of-mine, indigenous limestone; simplicity of plant design; reduced hazards and plant operating and maintenance costs accruing from the use of a less reactive chemical agent; higher solids concentration of the precipitated sludge; and no deleterious effect caused by accidental overtreatment. While total process costs could not be determined, it is conservatively estimated that the cost of treating mine water by the limestone process is one-third to one-half the cost of the lime process, depending on the characteristics of the water to be treated and the availability and quality of limestone used.

Jan 1, 1968

By M. C. Irani

The Bureau of Mines, in cooperation with the Mine Safety Appliances Co., has developed a continuous-recording methanometer utilizing a catalytic combustion detector. The methanometer, which is presently operating at 22 exhaust fans at 14 mines in the Eastern coalfields, is reliable and simple to install, operate, and maintain. The instrument and the details of its installation and calibration are described. Analytical data obtained by infrared spectrophotometer and gas chromatograph are presented to substantiate its re liability.

Jan 1, 1974

By E. D. Palmes

A new type of personal sampler for quantitative estimation of atmospheric concentrations of contaminant gases was first reported from this laboratory in 1972. The sampler requires no pumps or flow regulators and employs instead the motion of the gas molecules them-selves to furnish the power for sampling. Under this grant, work was completed on development of a kit for the field determination of both NO2 and NO. Detailed instructions for the preparation of the samplers and the use of the kit was supplied to the Technical Project Officer. Attempts were made to adapt the same type of sampler to the measurement of SO2 and CO. Both gas chromatographic and turbidimetric procedures for the final estimation of the S02 proved to be unsatisfactory. For CO no reagent was found which would react sufficiently rapidly with this gas to utilize the essential feature of the diffusion sampler, the maintenance of a diffusion gradient which is at least approximately numerically equal to the ambient concentration. A number of publications on use of the NO2 sampler, both at occupational and community air pollution levels, have resulted from this work.

Jan 1, 1979

By B. J. Moore

This publication contains analyses and related source data for 675 natural gas samples from wells and pipelines in 24 States and 5 foreign countries. The samples obtained and analyzed during calendar year 1980 are included in tables 1-4. Those samples included in tables 5-7 were collected during the years 1960 through 1979. However, permission to publish the analyses of those samples was not given until the past year when the operators were again contacted to seek release of the information. All of these samples were collected as a part of Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted in the United States by the Bureau of Mines since 1917. In late 1965, the survey was expanded to include foreign gasfields. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4862 and 576. The results of the investigation of the occurrences of helium are published annually to make the information available as soon as possible to the gas industry and the general public. Twenty-two previous publications have presented the results of 12,152 gas analyses made prior to 1980. The first three, Bulletins 486,' 576,5 and 617,6 contain analyses and related source data on 5,218 gas samples collected from 1917 through 1980. The other

Jan 1, 1981

By F. A. Penning

This report describes the development of skip and guide desings for vertical shafts in deep vein mines. Skip and guide systems for bottom dump skips are identified as being used in current practice. Mine visits were made to obtain current information on the needs and problems of operating mines. Methods of structural and mechanical analysis of skip bodies and bails are outlined. A dynamic computer model was written to find the dynamic interaction between skips and guides for guides with geometric misalinements. A materials evaluation section identifies currentavailable and applicable materials that can be used effectively for new skip construction. Guide materials are also presented. Analysis includes the economies resulting from streamlined buntons and from low skip payload ratios. Selection of materials is based on strength, abra¬sion and corrosion resistance. Design requirements related to the shaft environment are presented. Consideration for the selection of guides and buntons is also given. Conceptual design includes the concept of cylindrical skips, center-seeking guide rollers, and asymmetric bail design to decrease dynamic interaction. An outline for field tests is presented. Future research areas are: testing, guide geometry measure¬ment, advanced suspension, dynamics, and structural configurations.

Jan 1, 1977

By Richard I. Miller

Science Applications, Inc. has developed for the U.S. Bureau of Mines a rapid response radon monitor capable of accurately responding within three minutes to changing radon levels of magnitude from 100 to 10,000 pCi/1, typical of the levels in working uranium mines. The instrument weighs 17 pounds, is sized 12" x 10" x 6", and is capable of 8 hours of continuous portable operation with a self-contained, rechargeable battery power source. Residual chamber contamination from a radon level allowed to remain in the chamber for 90 minutes is about 10 percent, decaying about a factor of two in one hour. The instrument sensitivity is a nominal 0.1 cpm/(pCi/1), with a background count rate of less than 1 cpm.

Jan 1, 1979

By Liming Yuan

Barometric pressure changes affect air density, leading to change in the mass of the gas in the gob. When the barometric pressure decreases, the volume of gas in the gob expands, while the volume of gas contracts when the barometric pressure increases, causing the gob to breathe out and in. Although the concept of gob ?breathing? is simple, its effect on spontaneous heating of coal in the gob area is not clear. In this study, computational fluid dynamics (CFD) simulations were conducted to model the spontaneous heating of coal in longwall gob area under measured barometric pressure changes. A single longwall panel using a bleederless ventilation system was simulated. If there is no barometric pressure change, the intake airflow rate is equal to the return airflow rate. When the barometric pressure changes, these two airflow rates are no longer equal, and the difference between the two airflow rates represents the airflow rate the gob breathes in and out. The effect of inflow and outflow of gas on the potential spontaneous heating in the gob was investigated using the CFD model developed in our previous study. The effect of barometric pressure changes on the spontaneous heating was found to be dependent on the gob permeability and the coal oxidation rate. The effect of barometric pressure changes on oxygen concentrations in the gob was also examined.

Jan 1, 2010

By B. W. Gandrud

This report presents the data of one of a series of investigations of the washability of Alabama coals as indicated by float-and-sink tests made by the Bureau of Mines at the Southern Experiment Station in cooperation with the University of Alabama and Alabama coal producers The Klondyke mine, operated by the Blocton Mining Co., is about 1 mile east of West Blocton, Bibb County, Ala., near the southwestern extremity of the Cahaba coal field. The Bureau of Mines already has published three reports that deal with the washability of Cahaba coals - one a washability study of the Clark bed at Marvel4/, one on the tabling of fine coal from the Thompson and Woodstock bed , and the third a washablility study of the Henry Ellen bed at Acmar6/.

Jan 1, 1939

By E. D. Calvert

Molybdenum has been successfully cast into static and rotating molds in conventional equipment used for casting titanium and zirconium. Melting was accomplished by using an arc potential of 36 to 40 volts with a current of 10,000 amperes. Pouring efficiency, after a skull had been formed in the crucible, averaged 70 percent. Techniques are described by which four successful castings were made. Tensile properties on specimens cut from one centrifugally cast tube averaged: Tensile strength, 39,800 p.s.i.; yield strength (0.1 pct. offset), 35,300 p.s.i.; elongation, nil; reduction in area, nil; impact strength, 2 ft.-lb.; hardness DPH (diamond pyramid hardness) 180. Mold reaction was not evident in shapes cast in machined graphite. This was not true, however, for rammed graphitic-base molds.

Jan 1, 1960

By Harold E. Marr

A simple algorithm is presented for processing digitized X-ray spectra obtained with a Si(Li) or Ge(Li) semiconductor detector coupled to a multi- channel analyzer. The simplified least-squares procedure is used to smooth out the statistical fluctuations in the spectrum by repeatedly fitting a quad- ratic equation to a predetermined number of channels and performing a traveling smooth across the spectrum. A logarithmic transform is applied to the raw data to minimize the distortion of the gaussian-shaped peak profiles. The efficacy of the technique is evaluated by observing the distortion of several gaussian-shaped peaks that have been subjected to the smoothing operation. The locations of maximums and minimums in the spectrum are predicted in the process as well as the values of the peak heights. The convolution integers from a least-squares fit of a quadratic equation are calculated as part of a FORTRAN subroutine. The building-block approach to computer programing in a small laboratory is discussed.

Jan 1, 1972

By M. G. Wallis

This report presents the results of a study to develop a detailed mining method design based on longwall mining with sublevel caving. The method is applicable to low-dipping coal seams 20 or more feet thick such as are found in the western United States. The report covers (1) the development and description of the mining method, (2) evaluation of the engineering feasibility of the design, (3) estimates of productivity and recovery, and (4) an engineering cost analysis and economic feasibility evaluation of the mining method design.

Jan 1, 1977

By Douglas W. Fuerstenau

A detailed experimental study of breakage kinetics in a batch rod mill indicates that while the system is inherently nonlinear, the feed disappearance kinetics for the finer sizes and the coarser sizes at high holdups is well represented by first-order behavior. The set of breakage distribution functions was found to be normalizable and independent of particle holdup in the mill. The size discretized initial breakage rate functions were found to be inversely proportional to particle holdup and almost directly proportional to particle size. A linearized grinding model that results from the first-order Taylor's series expansion of the breakage rate expression was found to give good simulations of the mill product size distributions without recourse to any parameter improvement routines. Material transport through rod mills was evaluated by investigating the effect of operating variables on the holdup and residence time distribution of particulate solids flowing through the mill. Identical experiments performed in a continuous ball mill helped delineate the fundamental differences in particulate transport through these two types of mills. Mechanistic interpretations of the observed transport phenomena are presented, and their implications in the context of tumbling mill analysis and design pointed out.

Jan 1, 1980

By Kim B. Shedd

The U.S. Bureau of Mines Particulate Mineralogy Unit examined the habits of six zeolite minerals commonly occurring in domestic zeolite deposits. Mineral habit is of interest because current theory on the potential for sarcoma production in test animals emphasizes the size and shape of mineral particles, without regard to composition or structure. A scanning electron microscopic study revealed that, of these six minerals, only mordenite and erionite crystallized in acicular to fibrous habits, The fibrous varieties of these two minerals were characterized by size and shape on the transmission electron microscope, and their dimensions were compared with those of asbestos and amphibole cleavage fragments. When comminuted, these two minerals possess "fibrosity indices" similar to those of amphibole cleavage fragments. One sample, a rare woolly erionite, has uniform widths, large aspect ratios, and a "fibrosity index" similar to those of asbestos.

Jan 1, 1982

By Charles C. Boley

High-volatile A bituminous coal from the Allen mine, Las Animas County, Colo., blended with char produced from the same coal yielded accept-able metallurgical coke in a 500-lb movable-wall test oven. Nineteen experimental runs were carried out using several concentration levels of two different chars, 5.6 and 19.6 percent volatile matter, produced by entrainment carbonization of the base coal. With the higher-volatile char, an acceptable coke was produced at a 22.5-percent concentration; the lower-volatile char did not produce an acceptable coke at the concentrations investigated.

Jan 1, 1972

By Frank T. Greene

An investigation of the quenching behavior of coal dust-air flames was carried out. The literature relevant to coal dust-air flames was reviewed, including information on the agglomeration, sedimentation, and dispersal of dust clouds. The simple equations relating the various concentrations involved in dust flame propagation are given and their implications elaborated. It is shown that the concentration seen by a moving flame in a sedimenting dust cloud can differ significantly from the concentration commonly measured in such experiments. The known dust cloud phenomena which appeared significant in flame propagation studies were experimentally evaluated, and quenching diameters, flame speeds, and lean propagation limits for several tube diameters measured. For Pittsburgh seam coal, the Minimum Quenching Diameter (MQD) for dust between 10 and 20 µm was found to be between 0.7 and 0.8 cm, and the lean propagation for 3.2-cm tubes to be approximately 200 mg/liter. Similar MQD data were also obtained for Pocahontas and Sewell coals, Beulah lignite, and a 50-gal./ton oil shale. The effect of temperature, coal particle size, and propagation tube material were also investigated.

Jan 1, 1981

By W. P. Diamond

The direct method test was developed for general mine safety applications by the U.S. Bureau of Mines in the early 1970's to measure the gas content of coal samples obtained from the relatively shallow depths of eastern U.S. coal mines. Over time, applications for gas content data evolved which required increasingly accurate desorption values. It became evident that some of the inherent weaknesses in the original direct method test could best be addressed by abandoning the water displacement based desorbed gas volume measurements. The ideal gas law based modified direct method (MDM) and associated desorbed gas volume measurement apparatus was developed to provide the most accurate desorption values possible for rock samples obtained from any gas-bearing strata. The MDM has a number of significant advantages, including: (1) increased accuracy, especially for low gas content samples, (2) a test apparatus with an integral sampling port to facilitate the collection of uncontaminated gas samples, (3) an inherent head space effect correction in the periodic MDM desorbed gas volume calculations, (4) measurement of positive and negative desorbed gas volumes, (5) elimination of differential gas solubility effects as a source of error inherent in the water displacement methods, and (6) a compact and rugged test apparatus that along with the elimination of the ?glassware? required for the water displacement methods, facilitates its use in the field.

Jan 1, 2008

Mining and the related extractive and processing industries are chiefly responsible for America's high standard of living. Enormous quantities of sand and gravel, limestone, copper, iron and a myriad of other mineral commodities are required to sustain our growing nation. However, the mineral deposits, both domestic and foreign, are becoming increasingly difficult to find. Adding substantially to the problem, is the fact that the conditions are worldwide. Foreign politics are increasingly affecting mineral commodity availability. Figure 1, taken from Bureau of Mines, "Status of the Mineral industries 1976" illustrates our dependency (in some cases total) on foreign sources for vital mineral commodities. While few nations are capable of exerting an OPEC-like influence on any one mineral commodity, the threat of cartel arrangements and related control strategies is evident. Nationalization of entire industries, once they become self-sufficient, is also exerting a disruptive influence on a large portion of the mineral industries.

Jan 1, 1977

By Laurance L. Oden

The Bureau of Mines is developing melting data for binary combinations of the alkaline earth fluorides and yttria to facilitate the formulation of slag composition. Liquidus and solidus temperatures and solid solubilities were determined for the BaF2-Y203 system, and the information is presented as the phase diagram. The phase diagram was constructed from data obtained by ceramography, X-ray diffraction, and thermal analysis of specimens encapsulated in small molybdenum ampoules. The data indicate a simple eutectic system with maximum terminal solid solubilities of less than 1 mole pct. The eutectic temperature is 1,343° C, and the composition of the eutectic is less than 1 mole pct Y203.

Jan 1, 1970