Search Documents

By T. H. Miller

This piper is a continuation of a series of yearly review articles started in 1925 by Thomas Varley. The development of flotation has been rapid, and better understanding of the functions o' flotation reagents has resulted in many changes in the kinds and quantities o reagents used. It is the purpose of this report to present the information in such a manner as to be of value to the milling industry as well as to the manufacturer of flotation reagents. These data have been compiled from a. survey of approximately 250 flotation plants of all classes within the United States. Many of these plants made complete reports of their operations, out others were apparently unable to supply this information in sufficient detail to meet the requirements of this investigation. Although it is realized that the data obtained in this survey are not as full as they should be to render the greatest service possible to the milling industry, it is hoped that succeeding articles will include complete information regarding milling; conditions and recoveries. As in the past, every effort has been made to conceal individual plant operations. RESULTS OF INVESTIGATION Table 1 gives the tons of ore treated by gravity and flotation methods and the concentrates produced as reported by 208 plants. The totals of 77,043,535 tons of ore and 4, 596,640 tons of concentrates from this table compare with totals of 78,973,012 tons and 4,683,972 tons respectively (furnished by the Bureau of Mines, Division of Mineral Statistics), indicating that the milling survey is about 98 per cant complete.

Jan 1, 1930

By D. Bienstock

A high-B.t.u, gas can be synthesized by the catalytic methanation of a mixture of 2.5 to 3 parts of hydrogen to 1 part of carbon monoxide, obtained in the gasification of coal, using a steel catalyst followed by Raney nickel in a hot-gas-recycle system. Conversion of 99 percent of the H2+CO yields a fuel gas with a heating value of 983 to 1130 B.t.u. per cubic foot containing 78 to 96 percent methane, no carbon monoxide, and very small amounts of unsaturated hydrocarbons. With the steel catalyst alone, conversions were 85 to 90 percent, giving a fuel gas of 810 to 868 B.t.u, per cubic foot, or 847 to 975 B.t.u. on a C02-free basis. INTRODUCTION In 1948 the U.S, marketed production of natural gas was 5.15 trillion cubic feet; by 1958 it had reached 11.0 trillion cubic feet, a rate of growth of 8 percent annually. 4 5 Although demand is expected to increase less rapidly, by 1966 it may reach 16 trillion cubic feet, based on an estimated 4.7 percent annual increase.6

Jan 1, 1961

By D. Harrington

Metal-mine fires in the United States are not of frequent occurrence and relatively for of those that do occur result in loss of life, although many cause heavy property loss or are costly to extinguish. Over a span of years, however, more lives are lost in metal Trines from fires than from any other of the untoward occurrences which afflict metal mining, such as electrical storms, floods, cave-ins, magazine explosions, or strikes. In perhaps more than 90 per cent of the fires. in metal mines' there is no loss of life; hence, the general public, even the general mining public, seldom hears of these fires, though the property loss frequently reaches hundreds of thousands of dollars; on the other end, in some instances the property damage from an underground metal-mine, fire has been negligible and the loss of life comparatively high. In any comprehensive study of metal-mine fires, ventilation is certain to be found a vital factor. The influence of ventilation on fires and the influence of fires on ventilation are of vital importance. In metal-mine fires very few persons meet death from actual contact Pith heat or flame; nearly all fatalities are duo to asphyxiation or suffocation. A well-planned, well-installed, and well-operated mechanical ventilation system is unquestionably one of the best available present-day protections from loss of life and property in case of fire in a metal mine; that this is true is attested by the usual helplessness of mining officials in trying to handled underground fires in a mine that has not had the foresight to install mechanical equipment to control underground air flow. On the other hand, the establishment of high-velocity air currents without sufficient day by day attention to such details as the method of coursing, or controlling, or confining them most certainly tends to increase dangers from fires rather than to aid in the avoidance or elimination of these dangers; the truth of this latter statement is shown by the fact that the greatest, loss of life in metal-mine fires during the past 20 years has been in relatively well-ventilated workings, and in every case the life loss has been due to some more or less trivial or easily remedied defect in the Ventilating system - usually a defect that has had some reference to doors used or supposed to be used to deflect or control air currents.

Jan 1, 1933

By William C. Henkes

Anticipating the availability of space-altitude imagery from the Earth Resource Technology Satellites (ERTS), the Bureau of Mines investigated the possibilities of using suck imagery in its activities in solid waste disposal, reclamation of mine workings, and mineral resource inventory. The study indicates that monitoring open pit and strip-mining operations can be done using conventional techniques if the sharpness of the imagery is sufficiently high. Possibilities also exist for semi-automated processes for change detection. Additional experimentation is needed for multispectral discrimination and identification of mine-related phenomena.

Jan 1, 1971

Introduction The NIOSH Office of Mining and Construction Safety and Health Research has redesigned its Mining Safety and Health Web topic page. The updated page incorporates a significant amount of new safety and health information, plus an improved layout to better serve stakeholder needs. It also provides back-ground information about the NIOSH Mining Research Program, including research awards, core competencies, unique labs, community and educational outreach, and a brief discussion of how the research program is structured. The new Web topic page can be found at www.cdc.gov/niosh/mining. "Search" Feature The redesigned Web topic page features improved search capabilities. The "Search Mining" feature on each page lets you search only the NIOSH Mining Safety and Health Web topic page. The user can still search the entire NIOSH Web page by using the "Search NIOSH" option. New Safety and Health Topics Developers expanded the "Safety and Health Topics" and reorganized the site to make it easier to find information. Each topic link now has a significant amount of new and updated information, as well as links to related topics of interest. Safety and health topics include dusts, diesel exhaust, hearing loss, contact with electric current, fires, explosives, ventilation, emergency management, new and older workers, and education and training. All topics can be accessed from the home page (Figure 1). Publications Although the Web topic page highlights many of the most requested publications on the safety and health topic links, you can find a complete list of downloadable publications as well. More than 600 mine safety and health publications are now downloadable from the page. Short summaries let the user quickly identify publications of interest. Products The updated Web topic page offers more than 120 NIOSH mine safety and health products, including training exercises, toolbox talks, videos, computer software, guides, and checklists, many of which are downloadable. If not, instructions are given on how to obtain copies. Some of our products include: • Software to analyze horizontal stress, design pillars for longwall mines, and select roof bolts for ground control. • Educational software including the Hearing Loss Simulator, which simulates the effects of noise and aging; and Coal Country, which teaches children about coal formation, mining techniques, and everyday uses of coal. • Utility software including the HazCom Helper software to assist individuals in writing a HazCOM plan, as required by the Mine Safety and Health Administration (MSHA), to track hazardous chemicals at their mine sites. • Guides for troubleshooting roof support systems, under-ground workstation design, and seating design. • Training exercises and videos that can be used for safety training. Data and Statistics General mining statistics are used by a wide variety of stakeholders. The NIOSH Mining Web topic page offers statistical graphs, tables, maps, fact sheets, and other publications that document the mining population, injuries, fatalities, diseases, and occupational exposures for all mining commodities. If users prefer to analyze data themselves, downloadable files of MSHA data are available. These cover employment, production, injuries, fatalities, and accident data from 1983 to the present and are available in both SPSS® and dBASE® formats.

Jan 11, 2005

By John Soule

The Torpedo copper mine in the Organ Mining, District, Dona Ana County, N. Mex., was discovered in 1899, and production of copper from oxidized-ore deposits was begun in 1900. Production continued through 1907, but operations were only intermittent frown 1907 through 1921. The production of copper during these periods amounted to about 3,500,000 pounds. Reserves primary sulfide copper ore were believed to occur below the old workings, and after a detailed examination of accessible workings and a study of drilling records of several private companies by an engineer of the Bureau of Mines, a development program of diamond core drilling was initiated. This investigation was started October 3, 1949; and completed April 30, 1950. Four holes totaling 2,122.3 feet wore diamond-drilled, and 70 samples were analyzed. All drilling was done with a Government-owned hydraulic-feet drill having special rods and core barrels to increase the recovery of core in critical zones. This report describes the location, history, ore deposits, and factual data obtained by the Bureau of Mines from the drilling.

Jan 1, 1951

By Robert S. Schechter

A minitest of the new potassium chloride-potassium carbonate two-stage in-situ uranium leach process has been carried out at the Intercontinental Energy Corporation (IEC) Zamzow project site in South Texas. Substantial quantities of high concentration uranium were produced indicating the viability of the leach solution. The test results yield information regarding the reservoir dispersivity, the average cation-exchange capacity of the formation, and the distribution coefficients describing cation-exchange reactions. The test also indicates permeability anisotropy and the existence of disturbed flow fields.

Jan 1, 1985

By W. Hermanson

This report, which covers the period from January 16 to October 21, 1974, describes the work performed in compliance with the requirements of contract no. H0242028 and modifications 1 and 2 thereto. The purpose of the contract was to further reline and modify three of the canopies (shuttle car, loader, and roof drill) which were developed under contract no. H0220031, and to conduct further testing and demonstration of the relined designs. Modifications I and 2 involved conducting further in-mine evaluations of the face. drill and cutter canopies, also developed under contract no. H0220031. In addition to the canopy modifications, the contract involved an evaluation of an operator's seat concept for a shuttle car which was developed for the USBM by another contractor.

Jan 1, 1974

By E. M. Tignor

As a part of the program of promoting the conservation and efficient utilization of petroleum, studies are being made by engineers of the Bureau of Mines on secondary oil-recovery projects throughout the United States. In furthering that aim, engineering data concerning the reservoirs, methods of stimulating the production of oil, and other pertinent facts are collected, studied, and subsequently published so that others may profit by the experience gained. This report presents the results of a study made by engineers of the Franklin, Pa., office of the Bureau of Mines of secondary oil-recovery operations in the Boggs field, Spencer district, Roane County, W. Va., whore natural gas is injected into the reservoir to stimulate the production of oil from a so-called stripper field. The Boggs field, like most others in the Appalachian region, is one in which the major part of the natural energy that caused oil to flow through the reservoir to the producing wells during the primary stage of oil production has been dissipated. For all practical purposes, most of the oil produced in the Appalachian region at the present time can be considered to be from stripper fields. Consequently, secondary recovery methods are being used extensively in the oil-producing areas of New York, Pennsylvania, West Virginia, Ohio, and Kentucky for recovering some of the oil that was not produced by primary production methods.

Jan 1, 1949

By Edward L. Burwell

The Bureau of Mines conducted laboratory experiments to determine the change during retorting in the apparent permeability and the degree of compaction of beds of broken oil shale. Grades of oil shale studied ranged from 20.6 to 46.7 gallons of oil per ton (gpt), and the simulated overburden pressures applied to the shale were from 300 to 900 psi. Linear regression analysis of the data produced equations describing the response of the oil shale. Oil shales of approximately 20 gpt experience only minor apparent permeability reductions under test conditions, but richer shales (30 to 50 gpt) lose essentially all permeability. The permeability reductions were accompanied by corresponding decreases in bed height that ranged up to 37 percent of the original bed height.

Jan 1, 1974

By J. E. Murphy

A method is being developed by the Federal Bureau of Mines for recovering lead metal from galena without the generation of SO2. Lead chloride is obtained by leaching lead concentrate at a temperature of approximately 100° C with FeCl3 solution: PbS + 2FeCl. " PbC1 2 + 2FeC1 2 + S. Electrolysis of the PbCI 2 product in a fused-salt bath results in deposition of molten lead metal at the cathode and evolution of chlorine at the anode. The chlorine can then be absorbed in the spent leach solution to regenerate FeCl3 for recycling. Optimum electrolyte composition was a PbC12-LiCl eutectic containing 7.6 wt-pct LiCl. The PbCl2-NaCl eutectic also proved satisfactory. Electrolysis in the PbCl2-LiCl bath at 450° C yielded 99 pct current efficiency at a current density of 5 amp/in2 with an energy requirement of only 0.24 kW-hr/lb metal produced. This compares with 98 pct current effi¬ciency and 0.26 kW-hr/lb metal produced for the PbCI2-NaCI bath. A typical lead deposit contained less than 100 ppm total detectable metallic impurities. At the low temperature employed for electrolysis, there was essentially no vaporization of Pb or FbC12.

Jan 1, 1974

By M. E. Adam

This report describes the construction and testing of large (30 ft high by 55 ft wide) stopping and overcast structures in an oil shale mine. The work was undertaken to develop construction techniques and cost data, and to measure leakage rates on full scale structures in an oil shale mine. A design data base was developed by reviewing industry practice, oil shale industry plans, and technical literature. Alternate layouts for room and pillar mining were examined to find ways to reduce the size and number of ventilation control structures. Six full size stoppings and one overcast were built in the Colony Pilot Mine. Leakage rates were measured using both SF6 tracer gas techniques and the ?brattice window? method. The leakage was measured both before and after a full scale face blast. Blast air pressures were measured across two of the stoppings. Cost and leakage data were used to evaluate the projected overall performance of various combinations of the stoppings in a two-panel oil shale mine.

Jan 1, 1986

By R. L. Handy

The objective of this research was to devise and test an apparatus to rapidly evaluate the cohesive and frictional strength of coal in situ, in order to increase the safety and percentage of coal recovery from underground coal mines. During the first year device was designed utilizing the bore-hole shear test principle from soil shear strength testing: Two opposing corrugated plates are forced outward to exert a controlled contact pressure against the sides of a previously bared hole, and then the plates are very slowly pulled along the axis of the hole to cause shearing of coal in contact with the plates. Results with the device are expressed in terms of a friction angle[_] and a cohesion c. The [ ] angles obtained from an Iowa coal arc in close agreement with and fall between results from triaxial and direct shear laboratory tests on the same coal. The measured cohesion was found to be much less than from the comparable laboratory tests. It may be increased by pre-stressing and other techniques to embed the shear plate teeth for the first shear test point.

Jan 1, 1973

By K. L. Paciorek

The aim of the present study was to determine the thermal oxidative behavior of materials used in coal mines, with emphasis on the type and relative concentration of the products, in particular the toxic species formed. To supplement this work and to gain understanding as to the type of products possibly formed and also to assess the limitations and advantages of the various analytical methods used a literature survey of the past investigations performed on the compositions of direct interest to the subject program was conducted. The compositions thus covered were cellulose, polyvinyl chloride, neoprene, urethanes, polyamides, polyesters, polyethylene, epoxy, phenoxy, urea-formaldehyde and melamine formaldehyde resins. The results of this review are compiled in the Appendix. The experimental work consisted of thermal oxidative degradation of 36 materials and 4 composites using a stagnation burner apparatus developed in these laboratories which affords a dynamic system approximating somewhat the conditions encountered in underground coal mines. This technique as employed during this program gave only the relative product concentration at specific periods of the decomposition process, The advantage of this approach is that in this manner screening of materials can be accomplished in conjunction with some assessment of the decomposition rate as influenced by temperature and material composition. Limited static tests were performed using a sealed tube method. The materials studied were grouped according to their compositions. The following were the main groups: (a) polyvinyl chloride-containing materials, (b) neoprene compositions, (c) rigid foams (urethanes, isocyanates), (d) miscellaneous materials (including jute, fiberglass, polyethylene and some articles of unknown composition), (e) coal and fluids (phosphate esters, organic esters, oil-water emulsions), and finally (J) composites. The latter comprised a mixture of a phosphate ester fluid with (a) coal, (b) a representative polyvinyl chloride sample, and (c) a neoprene type composition.

Jan 1, 1972

By Rolland L. Blake

The Bureau of Mines investigated the mineralogy, tonnage, and beneficiating characteristics of oxidized (nonmagnetic) taconite iron resources of the Western Mesabi Range as part of its program to insure adequate future domestic mineral supplies. Magnetic taconite currently provides about 95 pct of Mesabi production, but the large tonnages of oxidized taconite between the magnetic deposits will be needed to help meet future domestic demand for iron ore. Three bulk samples that represent large tonnages from the Western Mesabi Range were selected to determine their mineral composition and liberation by light optical microscopy and to test their beneficiating response. This report describes the mineralogy and liberation characteristics of the three samples of the Biwabik Iron-Formation for 26.5 mi (42.7 kID) from Keewatin to Grand Rapids, MN. (Details of response to beneficia-tion were reported previously.) The samples represent mostly material from the Lower Cherty Member of the Biwabik-Iron Formation, although one sample included some Upper Cherty Member. Minerals of all three samples were quartz (chert), hematite, goethite, and minor to trace amounts of magnetite, iron carbonate, and iron silicates. It was concluded that the oxidized taconites of the Western Mesabi Range represent a subeconomic indicated resource that can be selectively mined and beneficiated as a future large source of iron feed for steelmaking.

Jan 1, 1983

By G. G. Campbell

The Bureau of Mines initiated a field test of underground coal gasitication to investigate the technologic feasibility of gasifying a subbituminous coal. The test site is near the town of Hanna, Wyo., about 70 miles northwest of Laramie. Preliminary results of the experiment are described. The coal was ignited in the central well of a 16-well pattern. Both forward and reverse combustion techniques were attempted to prepare a path of sufficient permeability to permit the high air injection rat s necessary for gasification. Gasification between linked wellbores was sustained for periods as long as 3 months. Hydrogen-rich gas having a heating value of 100 to 150 Btu/scf was produced.

Jan 1, 1974

By L. C. IlsLey

Permissible electric nine lamps are approved with the. understanding that if actively marketed they will be listed in Bureau of Mines publications so that state mine departments, compensation bureaus, mine operators, miners, and others interested in safety equipment for mines may know the permissible lamps available and the important safety features of each. The last list of permissible electric mine lamps was issued as Report of Investigations 33045 in June 1936, a supplement to Bulletin 332.6 All lamps described in Bulletin 332 are either obsolete or have been materially modified, as covered by extensions of the original approvals. These modified lamps and the new designs approved since 1930-totaling 12 cap lamps and 23 lamps of miscellaneous types-comprise the present list of actively marketed permissible electric mine lamps. This bulletin presents the Bureau's test requirements and procedure relative to permissible electric mine lamps and describes briefly the lamps, giving tabulated details of each.

Jan 1, 1942

By John E. Pahlman

The Bureau of Mines conducted column-leaching tests on 25 domestic Mn ores to determine the feasibility of extracting Mn by in situ or heap leaching with dissolved sulfur dioxide (S02) solutions. The ores tested were obtained from deposits in Arizona, Arkansas, California, Colorado. Maine, Minnesota, Nevada, and South Dakota. Dissolved S02 was found to be effective for leaching Mn; extractions greater than 90 pct were obtained with solution application rates of 1 mL/min from uncalcined, minus 2.5-plus 1.3-cm ore pieces. Leaching these ores with solutions containing only 5-wt-pct S02 and no added H2S04 resulted in Mn being selectively extracted over Fe except when Fe was present as goethite or siderite. Ca solubilization was inhibited by controlling the solution application rate (1 mL/min). The rate of leaching was found to be principally dependent upon the rate at which the leaching solution can penetrate the ore, since the solubilization of Mn upon contact with S02 was observed to be rapid. Despite low water permeabilities of the ores (as low as 10-2 to 10-4 darcy). greater than 90 pct of the Mn was extracted from even the largest ore pieces tested (approximately 10 cm in diameter). It appears, therefore. that leaching Mn opens up the pores, allowing penetration of the leach solution into the ore pieces.

Jan 1, 1988

By W. P. Haynes, J. W. Mulvihill, G. B. Taylor, S. Katell

Capital and operating costs have been estimated for separating methane and hydrogen in gas - separating plants designed to produce 90 million scf per day of product gas containing a minimum of 90 percent methane . After a preliminary literature review of various separation techniques , three different processes --moving - bed adsorption using active carbon , oil absorption , and liquefaction -- were chosen for the cost estimates . Three different methane feed gas concentrations , 5 , 20 , and 50 percent ( cases 1 , 2 , and 3 , respectively ) , were chosen as representative methane concentrations for the separation estimates . Capital and operating costs were lowest for the moving - bed adsorption process in all three cases investigated . Operating costs declined from $ 0.24 to $ 0.06 per 1,000 cu ft of product gas , and capital costs declined from $47,490,800 to $7,411,200 as the percentage of methane in the feed gas increased from 5 to 50 percent .

Jan 1, 1964

By E. V. Cilento, R. C. Laotz, K. A. DiGregorio

"PULMONARY ALVEOLAR macrophages (PAM) protect the lungs by providing a first line of defense against inhaled foreign debris and bacteria. In this role PAM phagocytize foreign matter, secrete enzymes that augment microbial killing and digestion, and produce reactive oxygen me-tabolites (2, 3, 18, 19, 22, 26). However, in addition to this antibacterial function, PAM participate in a diversity of functions, such as tissue repair, lipoprotein metabolism, and immunoregulatory activities (11, 22).Studies have suggested the existence of a heterogeneous population of PAM with respect to immunologic function, enzyme release, phagocytosis, morphological characteristics, expression of membrane receptors, ad-herence, and superoxide (O2•) release (4-7, 10, 16, 21, 23, 28). This heterogeneity has been observed by analyz¬ing subfractions of PAM separated by cell density frac-tionation. For example, using guinea pig PAM, Dauber et al. (7) showed heterogeneity in cell density and size, morphological characteristics, and cytochemical properties, whereas Holian and co-workers (16) reported variations in migration, chemotaxis, O2• release, and pinocytosis among subfractions collected. Similarly, O'Neill et al. (21) observed functional heterogeneity in rat PAM with regard to phagocytosis, O2 • release, and lysosomal enzyme activity.Several investigations have reported a correlation between PAM activity and cell volume. Most studies have shown that O2 release from PAM increased with decreasing cell size (15, 21, 25), although Bielefeldt Ohmann and Babiuk (4) reported a decreasing trend. However, Gallin (13) has suggested that significant variability may even exist within density-defined or cell-volume subfractions that could lead to misinterpretation of results concerning PAM heterogeneity.A better understanding of the heterogeneity in O2 production may be obtained by using single cell meas-urements to evaluate whether functionally distinct sub-populations actually do exist. As such, the present study was designed to examine heterogeneity in O2 • release from single PAM using a recently developed electrooptical technique (8). The initial oxygen metabolite, O2•, produced by NADPH oxidase at the surface of the plasma membrane, was measured by quantifying the reduction of nitro blue tetrazolium (NBT I to a diformazan precipitate. Measurements were made from video recordings of individual cells stimulated by their adherence to the bottom of a culture dish. The cell volume and degree of spreading also were determined directly from the same video recordings, and the data were correlated with the initial rate and maximum amount of diformazan produced by the same cell."

Mar 1, 1992