Search Documents

By Yael Miron

This report describes laboratory studies by the U.S. Bureau of Mines to determine the suitability of a static oxygen (OJ adsorption test for evaluating the self-heating tendencies of coals. Reliable minimum self-heating temperature (SHT) values from adiabatic oven tests were used as standards for comparison and evaluation. A suite of six coals was tested in the adiabatic oven and in sealed flasks. In the latter tests, both undried and dried samples, in a range of four particle sizes, were examined. Miniature pressure trans-ducers monitored pressures in the flasks, and gas samples taken at the end of the tests quantified all the gases present. An excellent correlation was found between the minimum SHT's and amounts of O2 adsorbed over a 7-day period for dried coals, independent of particle size. In addition, a good correlation was obtained between the minimum SHT's and pressure changes in the flasks at the end of the test for the same coals, also independent of particle size. Based on these results, the sealed flask test can be reliably used to determine the self-heating tendency of a bituminous coal sample.

Jan 1, 1990

By Arthur L. Murray

"INTRODUCTION In compliance with those provisions of the organic act establishing the Bureau. of Mines which relate to improvement of health conditions of persons engaged in the mining, preparation, or treatment of mineral substances, sanitary surveys have been made of towns and villages housing the coal miners, metal miners, and mill and smelter employees of Utah.The purpose of the surveys is to afford studies of conditions prevailing in the various mining and smelter towns so far as concerns housing, water supplies, sewage disposal, refuse disposal the handling of foodstuffs, general sanitation, wash and. change houses, and the control of preventable diseases, all of which directly or indirectly have a bearing on the health and efficiency of employees and their families. Certain other factors have been added to the general sanitary surveys such as school and recreational facilities, which have a decided influence on contentment and efficiency. Through comparisons of favorable and unfavorable conditions and practices, and the dissemination of such information, improvements can be effected which will benefit both the employees and the employers.ACKNOWLEGMENTSAcknowledgment is made of the many courtesies shown by the officials of companies and towns visited. In some instances the towns were entirely under the control of officials of mining companies, being on company property whereas, in other instances, the towns wars incorporated not under company management. Particular acknowledgment is made of the assistance given by the Utah State Board of Health through Health Commissioner Dr. T. B. Beatty."

Oct 1, 1932

By P. R. Jones

The Bureau of Mines has written a computer program for the design and cost of a shell and tube type heat exchanger, in which a change in phase occurs on the shell side. The total cost, which was minimized, includes the annual fixed charges and annual operating costs. The program was written to meet the following requirements: (1) Triangular pitch, (2) single or multiple pass, and (3) heating or cooling. Price optimum design was obtained for four standard tube diameters and pitch. Standard heat exchangers whose area equaled or exceeded the required area are also listed. The program was made adaptable to various fluids and to various tube dimensions by including many of the required data such as physical properties of the fluids, tube data, and standard shell data as input data.

Jan 1, 1969

By W. C. Phalen

During the search for deposits of soluble potash salts in the United States, carried on by the United States Geological Survey, much infor- mation was collected on the salt resources and industry of the United States. The more important features of the information thus gath- ered, compiled, and digested may be classified under five headings, as follows: 1. Geology of the salt deposits of the United States. 2. Theories relating to the origin and formation of salt deposits. 3. Chemical composition of saline materials in the United States, principally rock salt and natural and artificial brines. 4. Statistics of salt production in the United States. 5. Technology of salt production. The first four items are not discussed in this report, but their treatment will comprise a separate report published by the Geologi- cal Survey, which will supplement this report, relating to salt- making processes, and will describe comprehensively the salt resources of the United States. Persons desiring a copy of that report should apply to the Director of the United States Geological Survey, Wash- ington, D. C. In addition to the discussion of processes, this report gives a brief description of the more important sources of salt in the United States. This description has been abstracted from the much length- ier description contained in the report to be published by the Geo- logical Survey.

Jan 1, 1917

By Manuel Gomez

This report presents prediction equations for 12 variables that are indicative of metallurgical coal quality. The variables include six for coke strength and six for carbonization product yields. All variables were predicted for coking coals having volatile matter contents from 16.3 to 42.1 percent, dry basis. The prediction equations, developed by mathematical-statistical techniques, were based on information from the proximate and ultimate analyses, the size consist, and the petrographic composition of bituminous coals carbonized in BM-AGA retorts at 800°, 900°, and 1,000° C. The equations were evaluated for validity with independent data derived from the 900° C carbonization of 33 binary blends of various coals and 22 binary blends of Pocahontas No. 3 low-volatile bituminous coal with 11 high-volatile bituminous coals. Results show that metallurgical coal quality can be predicted ahead of mining because data used to derive the prediction equations can be obtained at the time of exploration. Capability to forecast coal quality is useful in mine planning and should provide basic information for optimization of blending and crushing techniques and thus lead to the production of uniform coke.

Jan 1, 1970

By Llewellyn A. Rubin

ROUTINES AND SUBROUTINES A- 1 Wait Loop (Wait) A- 2 Receiver Processing (RCVP) A- 3 Control Panel Sequence (CPNL) A-4 Interrupt Routine (INTRP) A- 5 Math Processing Routine (PROC) A-6 Input Constants for Math Routine (CONI) A-7 Angle Conversion Routines (LVERT) A- 8 Display Routine (DSPY) A- 9 Message Print Auxillary Routine (MESSO) A-10 Auxillary Subroutines (AFUTC and AGETC)

Jan 1, 1973

By W. C. Phalen

During the search for deposits of soluble potash salts in the United States, carried on by the United States Geological Survey, much information was collected on the salt resources and industry of the United States. The more important features of the information thus gathered, compiled, and digested may be classified under five headings, as follows: 1. Geology of the salt deposits of the United States. 2. Theories relating to the origin and formation of salt deposits. 3. Chemical composition of saline materials in the United States, principally rock salt and natural and artificial brines. 4. Statistics of salt production in the United States. 5. Technology of salt production. The first four items are not discussed in this report, but their treatment will comprise a separate report published by the Geological Survey,a which will supplement this report, relating to salt-making processes, and will describe comprehensively the salt resources of the United States. Persons desiring a copy of that report should apply to the Director of the United States Geological Survey, Washington, D. C.

Jan 1, 1917

By Sam McNary

The U.S. Bureau of Mines used the East Fork Pine Creek watershed to conduct a pilot study for an inactive and abandoned mine lands inventory, during which techniques and methodologies would be developed for subsequent inventories. A total of 177 waste dump samples, 191 mill tailings samples, and 36 stream sediment samples were collected. Water samples were collected from 18 sample sites during five sampling events. Waste dump, tailings, and stream sediment samples were analyzed for antimony, arsenic, cadmium, copper, iron, lead, mercury, and zinc. Results indicate a multidisciplinary approach is necessary: disciplines should include geology, geostatistis, geochemistry, geophysics, biology, hydrology, and remote sensing; small prospects do not generally contribute to watershed contamination, major mine and mill sites may contribute metal enriched sediment of metal enriched water; speciation studies and bioavailability studies are important.

Jan 1, 1995

By Max F. Lee, Warren A. Peck

The applicability of the Q-system [Barton et al. 1974] to Australian underground metal mines is discussed with reference to two common design issues: ground support for horizontal mine development, and assessing the stability of bored raises. Installed ground support in mine development is com-pared to empirical estimates using the Q-system and associated support capacity calculations. Data are graphically presented from 59 specially selected sites at 15 contributing mines. The actual performance of large-diameter raise-bored shafts is also compared to empirical stability assessments using a modified version of Q (Qr, after McCracken and Stacey [1989]). Lower-bound Qr values are plotted against raise diameter for 47 selected sites at 23 mines in Australia and Papua New Guinea. The influence on Q and Qr of some geotechnical aspects of the Australian landscape, the dynamic nature of mines (compared to civil construction), and occupational health and safety regulations are discussed. Stability and support assessments that are based just on Q or Qr are not always conclusive. It is often necessary to consider other rock mass parameters, the regulatory environment, and risk issues. These results are interim; further data collection and analysis are required with regard to comparing actual performance versus empirical assessments.

Jan 5, 2007

By Z. J. Fink

Ultraviolet-visible and infrared emission spectra from propagating methane-coal-dust-inhibitor mixtures have been obtained in a 0.2-by 0.2¬by 5.3-m vertical duct over a range of flame speeds from 2 to 100 m/sec. Results serve as a basis for the design and evaluation of thermal radiation detectors for triggered barriers that suppress ongoing mine explosions. Of particular significance is the large continua superimposed on the methane-air spectra when small amounts of coal dust are present and the variation of emissivity with infrared (IR) wavelength in dust flames. In conjunction with the spectral measurements, studies of flame speed, particle size, gas sampling plus thermodynamics, and dust sampling are presented and discussed in order to gain insight into the more fundamental aspects of propagating explosions. Sampling results have shown that only a near-stoichiometric amount of dust is consumed in the flames studied even though initial concentrations are five times stoichiometric. Difficulty in propagating coal-dust inhibitor flames of realistic mine characteristics in a cold-walled laboratory duct has been encountered. A simplified analysis of the flame zone utilizing spectral and sampling results indicates that the stability of slowly propagating flames is more dependent upon thermal radiation than upon convection losses to the walls. It is predicted that thermal radiation losses will make any measurements of coal dust burning velocities, "quenching diameters," or flammability limits more apparatus dependent than those corresponding to gaseous fuels.

Jan 1, 1974

By E. D. Wilson

A study of factors related to subsidence was specified in a project proposal entitled "Structural Analysis of Block-Caving Operation, San Manuel Copper Mine, Pinal County, Ariz.," approved by the Bureau of Mines early in 1953. This proposal was designed by Charles H. Johnson, then chief of the Base Metals Branch of the Minerals Division, Washington, D. C., assisted by Dr. Leonard Obert, chief of the Applied Physics Branch, Region VIII (now Region V), College Park, Md., and E. D. Gardner, chief mining engineer, Bureau of Mines, Washington, D. C. It read as follows: This project is a study of the mechanics of undercut block caving in a deep ore deposit. The San Manuel is a low-grade disseminated copper deposit containing nearly a half billion tons of ore lying at depths of 500 to 2,000 feet. Development is just starting. Production is to begin in 3 to 4 years (in 1956) at a rate of 30,000 tons of ore a day, or 60,000 tons of copper a year. A Government loan of $90,000,000 /subsequently increased to $94,000,000/ and a long-term Government purchase contract support the capital investment, which will total about $110,000,000.

Jan 1, 1957

By M. F. Dunn

The objective of this work was to define jet fan performance in d variety of large cross-section underground mine applications and to develop guidelines for thin performance in open airways, dead headings, and multiple face areas. Measurements include common ventilation instruments, continuous recording remote electronic anemometers to measure air velocity, and sulfur hexaflouride tracer gas with chromatograph analysis to determine dilution rates and air recirculation. For open airways the following were determined: Large jet fans are leas efficient in smaller airways, but quite effective in larger open airways for achieving both uniformity end greater air entrainment, when inclined about 10° or elevated. For dead headings the following were determined: The jet fan must be placed against the rib of the heeding closest to the incoming airstream from the crosscut or recirculation will increase. The fan should be placed at the pillar corner to increase airflow. As the fan is moved closer inby, recirculation increases. Larger fans promote recirculation. Inclining fans about 12° improves airflow in large headings. For face areas the following were found: For panels having uncontrolled airflow, the fan should be placed in the incoming airflow, about one pillar inby, and directed diagonally across the faces. For panels having narrower rooms and controlled airflow, the fan should be placed alongside the panel side in the first room so as to direct or intersect the incoming airflow at the next entry or crosscut.

Jan 1, 1983

By Murray Jacobson

Facts obtained by the Bureau of Mines on the dust-explosion hazard in air of materials used in the plastics industry are presented for 313 samples studied in the laboratory. Information is given on ignition temperature of dust clouds and layers, minimum explosive concentration, minimum energy required for ignition, explosion pressure and rates of pressure rise, amount of inert dust required to prevent ignition and flame propagation, and, in some instances, on the limiting oxygen concentration in an atmosphere to prevent ignition by spark and by heated surface. The effects of particle shape, additives, and resin structure on explosibility are discussed. Relative explosibility of the materials is related to the ignition sensitivity and explosion severity and is denoted by an empirical index. Recognition of the degree of hazard will facilitate adoption of adequate measures for preventing ignition and explosion during manufacturing or processing.

Jan 1, 1962

By Chris Jobes, Alan Mayton, N. Kumar Kittusamy, Dean Ambrose

NIOSH researchers conducted a study to compare seat designs on underground coal mine haulage vehicles. The objective of the study was to support prior findings that NIOSH-designed seats, which incorporated ergonomic design features (e.g., viscoelastic foam padding and low-back support), are improved designs. Based on measured levels of vehicle jarring/jolting and perceived discomfort, researchers evaluated four different designs - two in-use and two NIOSH-developed, ergonomic designs. Researchers collected data using a short questionnaire, a linear, visual analog scale, and accelerometers with a data recorder. Results showed that vehicle operators favored the NIOSH seats with added adjustability, low-back support, and improved seat padding over the existing seats. In addition, the measurements indicated all NIOSH seats performed better than the existing seat, under the no-load (worse of two) conditions, in reducing peak acceleration, crest factor, and RMS acceleration. The authors summarize the data collected and operator preferences for seat designs and different foam padding arrangements.

By Gerald L. Finlinger

This Bureau of Mines publication reviews underground methane drainage programs being conducted in various coalbeds. Equipment used in drainage programs such as drills, underground pipelines, and methane monitoring systems is described.

Jan 1, 1980

By Donald E. Redmon

Industrial engineering departments perform staff duties and are most effective when sincerely supported by management. In accordance with the needs and desires of the mining companies involved, various industrial engineering functions have been adopted widely at western metal mines during the period 1950-60. Newly organized departments usually conduct method and equipment studies, work-measurement programs, and establish and maintain production standards. Supervisor-training programs and courses are effective in showing the relationship between supervisory responsibility and the purpose for which industrial engineering is practiced. Industrial engineering staffs of western metal mines are composed predominantly of personnel from within the companies. Experienced industrial engineers, not necessarily experienced in mining, frequently are hired by a company to help establish the department. Management consultants frequently are called upon to advise management and instruct department personnel in industrial engineering practices. Some departments have developed satisfactory industrial engineering programs without benefit of formal industrial engineering training or advice.

Jan 1, 1962

By Louis P. Domingues

As part of a study on high-temperature ceramic materials, the ammonium sulfate, carbonate, nitrate, oxalate, and sulfate salts of yttrium, lanthanum, and cerium were analyzed thermogravimetrically. The temperature ranged from room temperature to 1,500° C. Each salt was decomposed by heating at a rate of 2.5° C. per minute, and some of the salts were subjected to additional rates of 5° C. per minute or 10° C. per minute. The decomposition sequences have been identified, and the temperatures of formation of intermediate compounds and of the oxides have been determined. The minimum oxide formation temperature of a given lanthanum salt exceeds that for the similar salt of yttrium, and both exceed that for the same salt of cerium except for one cerium carbonate. Variation of the heating rate indicates a thermal lag in the materials and produces the shift of formation temperatures to higher values and loss of resolution in the weight-loss distribution as the heating rate increases.

Jan 1, 1962

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0,79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without re-treating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams, Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0.79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without retreating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some -were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams. Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as “Good” to “Very Good” using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.