Search Documents

By N. A. Eilertsen

The Aroostook manganese-bearing deposits lie within a rectangle 30 miles wide and 70 miles long. Over 40 different deposits have been discovered in this area, but they have not been mined because the ores are difficult to treat. In 1949, the Maple Mountain area was selected for detailed investigation by the Bureau of Mines, because study by the State of Maine and the Federal Geological Survey indicated that it was the most promising in Aroostook County for developing a large tonnage of reserves. Investigation by the Bureau of Mines disclosed that all of the reported deposits of the central district were located on the limbs of a syncline underlying a pear-shaped area of 283 acres between the crests of Maple Mountain and Hovey Mountain. The ore area has been outlined by trenching and drilling along three sides of the perimeter, while the remaining side is defined by a fault. The area has a length of 6,300 feet and a maximum width of 3,100 feet. Diamond-drill holes have intersected the deposit as deep as 1,550 feet below surface, but additional deep drilling would be required to determine the intensity of folding or warping at depth. The Maple Mountain-Hovey Mountain deposit lies in the slates of Ordovician age and is classified into three zones, of which the upper, averaging about 57 feet thick, is designated manganiferous purple and red slate. The central zone, also averaging about 57 feet thick and containing the highest manganese content, is manganiferous, banded hematite. The lower zone is manganiferous, interbedded hematitic and green slate with an average width of about 33 feet. Manganese minerals occur with hematite in all three units. Trenching on the northwestern slope of Hovey Mountain uncovered other disconnected deposits of manganiferous rocks of earlier age than the ore of the syncline. The general strike of these deposits, which range from 15 feet to 75 feet in thickness, is southwest a length of 5,000 feet. They dip steeply southeast. The ore of the syncline is predominantly deep, hematitic red, inclining to red-dish black, fine-grained, dense, and thinly laminated. It is hard and siliceous. Hematite has, in places, been altered to magnetite. Because of the fine-grained texture of the ore, the manganese-mineral constituents are difficult to determine. Of the manganese silicates present, braunite is the most readily identified. Manganese carbonates and oxides are found also.

Jan 1, 1952

By Jasinder S. Jaspal

In underground room-and-pillar mining methods, the sectional conveyor belts are extended or retracted periodically to maintain shuttle car tramming distance to a minimum. A conventional conveyor belt extension or retraction is a heavy, arduous job that if mecahnized, has the potential to improve productivity and safety. To reduce the burden of heavy work of this activity and mechanize it, the Bureau of Mines developed a conveyor belt service machine (CBSM) through a research contract with Tractor MBA. The CBSM is a self-contained, battery-powered, rubber-tired vehicle capable of handling, storing and transporting conveyor belting, wire rope, and associated belt structures in seams as low as 48 in. Belt extensions and retractions are accomplished by moving the tailpiece of a belt conveyor with the CBSM to the next position while dispensing or retrieving the belt, wire rope, and associated belt structures. The CBSM improves the belt extensions and retractions by making them easier and faster, and it utilizes fewer workers. The CBSM was surface tested at the Bureau's Mining Equipment Test Facility (METF) to evaluate its performance and reliability. Modifications were made to the CBSM to correct deficiencies found during surface testing.

Jan 1, 1988

By Robert H. King

An analysis of low-voltage shielded trailing cables is performed to develop a method for calculating the differences in operating costs between shielded and non-shielded cables. Two types of shield constructions are considered (SH-C and SH-D) for the three major underground coal mining methods. Data from laboratory and in-mine testing are presented in addition to an analysis of safety benefits. Recommendations for further investigations are proposed. Example calculations with sensitivity analyses are presented. Recommendations for further investigation include costs impact considerations.

Jan 1, 1980

By E. C. Lane

This is the first publication in a projected series of reports on properties of commercial motor fuels pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The report gives results of analyses in oil-company laboratories of samples of gasoline obtained from service-station pumps in 18 marketing areas by representatives of oil companies. These companies obtained the samples and analyzed them for their own information and supplied data from their laboratory reports to the Bureau of Mines for compilation and publication. History of Bureau of Mines Gasoline Surveys The following quotation from Report of Investigations 3162/4 is included in this place for the information of readers who are not familiar with the Bureau of Mines gasoline surveys that have preceded the present report:

Jan 1, 1936

By S. L. May

Procedures for separating columbium and tantalum have been developed by the Bureau of Mines as part of a broad research program on the utilization of low-grade ores of columbium and tantalum, Columbium and tantalum compounds of greater than 99 percent purity have been obtained by application of the solvent extraction separation system: Hydrofluoric acid-sulfuric acid-methyl iso-butyl ketone. This system is unique in that it not only separates columbium from tantalum, but also separates these two metals from other metallic impurities. The system is effective for separating the metals irrespective of the tantalum and columbium ratio of the starting materials. Investigations in which the spent feed obtained from the initial coextraction step was recycled to the system indicated that efficiency was increased, and cost was reduced without impairing product purity. Continuous tests demonstrated that this solvent extraction system could be used in large-scale equipment without loss in efficiency or in purity of products. The separation of columbium and tantalum has been difficult because of the similarity in their chemical bahavior. Many methods have been proposed for separating these two elements, but most methods either did not achieve satisfactory separation or were tedious and time consuming. The Marignac process (3, 4)4 developed in 1866 was the only method used commercially until recently. This separation procedure is based on the difference in solubility in aqueous solution of potassium tantalum fluoride and potassium columbium oxyfluoride. Current commercial practice appears to favor solvent extraction as a method for separating tantalum from columbium (1). Several efficient methods for separating columbium from tantalum by solvent extraction (2, 9, 8) were reported earlier from this laboratory.

Jan 1, 1961

By William J. Campbell

Evaluation by the Bureau of Mines of published expansion values for magnesium oxide shows significant variation in values, which may be attributed to sample variables, experimental errors, or systematic differences between measuring techniques. To eliminate the sample variable in measuring expansion, thermal expansion characteristics of a high-purity polycrystalline magnesium oxide were determined by 21 cooperating laboratories using one or more of the following techniques; X-ray camera, X-ray diffractometer, dilatometer, interferometer, and telemicroscope. All expansion values were corrected by the author to a single reference temperature of 25° C. Linear expansion was expressed as a power series in the form of the following equation. Expansion (percent) = [[ A + B (?t) + C (?t)2] ?t 104] The constants, A, B, and C, were determined by least square techniques for X-ray camera, X-ray diffractometer, and dilatometer data separately, and for combined data of all five techniques. Expansion values are tabulated from 26° C. to 1,400° C. in 2° C. intervals using constants derived from X-ray camera data. Below approximately 500° C., expansion values obtained by dilatometric and interferometric methods are significantly lower than those by X-ray methods; above 500° C., this bias decreases rapidly. Comparison of results within methods showed the least variance for X-ray camera results; dilatometer and X-ray diffractometer results have about the same variance. The average deviations, in percent, between observed and calculated expansion values among methods were approximately 10 percent from 100°C. to 300°C., 5 percent from 300°C. to 500°C., and 2 percent from 500°C. to 1,400°C. Maximum deviations were approximately twice as large in most instances.

Jan 1, 1962

By J. C. Edwards

The Bureau of Mines developed a mathematical model for analysis of the impact of scrubber bed length, porosity, and gas flow rate on the absorption of C02 in a breathing apparatus. The model accounts for the decrease in available absorbent through chemical conversion. The pre-dicted efflux of C02 from a canister containing LiOR compared favorably with measured values reported elsewhere. It was determined from a com-putational study that the time for breakthrough of C02 at a prescribed level is nearly directly proportional to bed length and inversely pro-portional to gas flow and porosity.

Jan 1, 1987

By W. J. Wiehagen

The Work Crew Performance Model (WCPM) seeks to define performance variability within similar tasks of an underground work crew and relate observed variability to a cost consequence. Performance variability is described using work site observations to determine the adherence to job elements con¬tained within a standard operating procedure. Key components of the WCPM include (1) job definition through task analyses and the ranking of job elements by perceived cost consequence, (2) observational techniques for establishing performance baselines by measuring adherence to safe and proficient job procedures, and (3) cost linkages between adherence to task procedures and measures of consequence for noncompliance. Data presented within this report were obtained through the study of shuttle car operation in an underground mine in Appalachia. Observed adherence to safe and proficient job procedures by opera¬tors matched well with the consensus profiles (measured through a nominal group technique) with min¬ing personnel. It was also found that experienced operators consistently outperformed less experienced, incidental operators. These findings imply potential use of the WCPM as a practical procedure for thinking systematically about the choices available to reduce performance variability. Field application of the model can offer useful data to evaluate training and financially support performance improvement strategies that can be tested for their ability to reduce human error.

Jan 1, 1994

By John C. Gagliardi

The U.S. Bureau of Mines, in cooperation with Carter Mining Co., conducted vibration tests of four off-road vehicle seats. The purpose of the tests was to determine which seat provided the best vibration attenuation under laboratory conditions. Laboratory tests were constructed to simulate the mining vibration environment within the limitations of the test equipment. The acceleration test levels and corresponding response of the seats were low compared to ISO 2631's fatigue-decreased-proficiency time limits. Two of the seats employed mechanical suspensions and two seats employed air suspensions. The seats were tested using a 22,241-N (5,000-lbf) electrodynamic shaker. Mechanical suspension seats were tested with various preload-to-mass ratios (PMR's) and cushion densities. Air suspension seats were tested with various air pressure levels and seat cushion densities. Air suspension seats provided good vibration attenuation if pressurized greater than 552 kPa (80 psi). Mechanical suspension seats' attenuation performance decreased if the PMR exceeded 9.8. Seat cushions of lower density provided less vibration damping.

Jan 1, 2010

Table 1.-Salient aluminum statistics (Thousand short tons and thousand dollars) [ ]

Jan 1, 1967

By Forrest T. Moyer

In 1969, the number of fatal injuries in the coal mining industry was lower than in any previous year and the number of nonfatal injuries was lower than in any preceding year except 1968. Fatal injuries in 1969 totaled 203 with frequency rates of 0.85 per million man-hours of worktime and 0.36 per million tons of coal These rates were new annual lows. Nonfatal injuries totaled 9,917 with frequency rates of 41.76 per million man-hours and 17.42 per million tons. The severity rate for fatal and nonfatal injuries combined was 7,359 days lost or charged per million man-hours. The average severity was 173 days lost or charged per injury. These statistics represent the injury experience of an average of 133,302 employees per day working an average of 225 days in 5,955 coal mines for a total of 237-5 million man-hours worked and a coal output of 565 2 million tons

Jan 1, 1973

By T. A. Henrie

One objective of Project Gnome is to study the feasibility of a phase of the Plowshare program recovering thermal energy from an underground nuclear explosion. The test will be conducted in an underground salt deposit. It is anticipated that some of the energy thus released will be stored as thermal energy in molten salt. This report describes the pre-Gnome experiments conducted at the Federal Bureau of Mines Metallurgy Research Laboratory, Boulder City, Nev. The objectives of this study were to determine the problems involved in the recovery of thermal energy from molten salts to assist in planning the experimental program for the Gnome project.

Jan 1, 1961

By S. H. Ash

NO MORE important question has come before the coal-mining industry in many places, especially in the anthracite region of Pennsylvania, than prevention of stream pollution by mine drainage. Available information on acid mine drainage in the anthracite region of Pennsylvania indicates that a pollution problem must be solved in any program of anthracite mine drainage. The major problem concerns satisfactory disposal of the daily average mine-water discharge of 327,000 gallons per minute (g. p. m.), or 472 million gallons per day (g. p. d.), containing a free-acid load of 431 tons or a total acid load of 934 tons a clay as H2S04. This report indicates the scope of the problem and gives some suggestions concerning its solution.

Jan 1, 1951

By H. N. Dunning

A comprehensive research program designed to aid development of new and improved methods for more complete production of petroleum from partly depleted reservoirs is being conducted at the Bureau of Mines Petroleum Experiment Station, Bartlesville, Okla. Water flooding has accounted for much of the petroleum produced by secondary-recovery methods; however, a considerable portion of the crude oil commonly remains in place after water flooding has been terminated. In recent years the possibility of increasing the efficiency of water flooding by using surface-active additives has received wide attention. In general, the results of laboratory research have shown that use of detergents as water-flooding additives will reduce the residual petroleum in porous media (1).3/ Some less extensive field tests have supported this conclusion but have not been entirely conclusive (2). Later studies (3, 4) have given conflicting evidence as to the relative worth of detergent additives for water floods in water-wet (hydrophilic) or oil-wet (hydrophobic or lipophilic) reservoir materials. The results of these studies emphasize the need for a more complete understanding of the fundamental principles involved in displacing petroleum from reservoir surfaces by injected fluids. Accordingly, a comprehensive research program was initiated to investigate the practical and fundamental aspects of detergency in petroleum production.

Jan 1, 1953

The papers contained herein summarize results of various recent Bureau of Mines investigations in the area of mine power distribution systems. They are based on information from Bureau personnel, contractors and grantees, and Mining Enforcement and Safety Administration. Conclusions drawn from a series of parameter measurements on mine power systems, taken over a 3-year span, are presented. Personnel and equipment hazards due to faults on isolated, solidly grounded, and resistance grounded three-phase systems are discussed. Two papers cover dc applications of circuit breakers, including a novel protection scheme for trolley lines. The methods of suppressing induced arcing currents and voltages in a-c machines are evaluated. An evaluation program for ground monitors is described. Acceptance test procedures and the importance of various paparameters for trailing cable splice are covered. A number of techniques for locating faults in trailing cables are described.

Jan 1, 1975

By Maureen M. Foss

Underground coal mining is hazardous due to changing geological conditions. One geophysical method showing promise for in-seam hazard detection is ground-penetrating radar (GPR). The Bureau of Mines recently completed preliminary studies to demonstrate the feasibility of using GPR for in-seam hazard detection. Investigations included air and coal tests for the purpose of checking equipment accuracy, coal penetration, and other factors such as the effects of receiver orientation. Further investigations involved using both a short pulse and a new prototype synthetic-pulse system to locate a clay vein in a coal seam using trans-illumination. Data were gathered on multiple travel paths, and a back projection processing technique was then used to create a tomographic image using the calculated velocities. A computer model of the same coal seam was subsequently processed using the same tomographic tech-nique, and the results were compared with those of the actual data. Analysis of the tomographic images shows the presence of the clay vein, although its boundaries are unclear due to the tomography method used. Results of these preliminary studies show that GPR is feasible for use in in-seam hazard detection and point the direction that future research should take. A need has been shown for research involving more sophisticated tomography techniques, transmission studies on thicker coal seams, and reflection studies using the synthetic-pulse system.

Jan 1, 1987

By S. M. Shelton, R. B. Fisher, M. M. Fine

"INTRODUCTION The Batesville manganese district lies in the southern part of the Ozark region, mostly in Independence County but partly in Sharp, Izard, and Stone Counties of north central Arkansas.Oxides, carbonates, and silicates of manganese are found in the district. 4/ Carbonate ores have been mined from time to time, but the reserves of potentially commercial ore are chiefly black manganese oxide minerals.The district has produced manganese ore for many years. lip to and including 1933, 160,804 long tons of ferruginous manganese ore (10 to 35 percent manganese) and 140,277 long tons of metallurgical ore (35 percent or more manganese) were shipped;./ most of it was wad orThe term ""wad ore,"" used locally to designate the soft, clayey de¬posits of oxide ore, is a partial misnomer. The ores contain a soft, low-specific-gravity mineral of indefinite composition, which can be designated as wad, but coarse and fine particles of psilomelane and hausmannite, with a smaller proportion of braunite, pyrolusite, and indefinite manganese silicates, are also present. Large and small lumps of high-grade, hard manganese oxide minerals are found, frequently embedded in a soft, black matrix of fine particles of manganese oxides mixed with gangue."

Jul 1, 1942

By X. Chi, J. W. Griffith, C. L. Schengrund, J. Sabol

"Experiments were carried out to determine the long-term effect of instillation of 500 mg of generic bituminous, anthracite, quartz, or titanium dioxide (Ti02) dust on the composition of pulmonary surfactant. Dust was instilled in the caudal lobe of the right lungs of female pigtailed macaque monkeys (Macaca nemestrina). The composition of surfactant isolated from cell-free bronchoalveolar lavage (CF-BAL) samples obtained from right lungs (dust exposed) at various times over the following year was compared with that of surfactant isolated from CF-BAL from left lungs (dust free) . Little change was seen in the amount of surfactant-associated lipid phosphorus as a result of exposure to dust. Exposure to quartz, anthracite, or Ti02 dust induced a significant increase in the total amount of protein in the surfactant-enriched fraction. The relative amount of specific proteins was also altered: surfactant-associated protein A decreased, and the amount of the heavy and light chains of immunoglobulin molecules (identified by NHiterminal amino acid sequence analysis) increased. These changes were visible more than a year after instillation of quartz and at least 3 months after instillation of anthracite dust. Despite variation in the responses of the individual animals, the changes observed might serve as an indicator of the severity of the effect of exposure of the lung to mineral dust and/or to pathogens. IntroductionSurfactant is essential for normal pulmonary function and gas exchange. It functions to reduce surface tension and may help to prevent pulmonary edema [19] and to protect against infection [13]. The importance of surfactant to normal Jung function is illustrated by the fact that neonates lacking appropriate surfactant undergo respiratory distress and do not survive without clinical support."

Dec 1, 1996

By Terry J. Close

In 1985, at the request of the U.S. Bureau of Land Management, the U. S. Bureau of Mines studied part of the 56,623-acre South McCullough Mountains Wilderness Study Area (NV-050-435) in order to evaluate its identified mineral resources. The area studied is located in Clark County, NV, about 30 miles southwest of Boulder City. No mineral resources were identified. The study area contains the eastern part of the unorganized McCullough Mountain (McClanahan) mining district which has had no recorded production. Between 1911 and 1982, 23 lode claims were located in the part of the mining district that is in the study area; four of these claims are currently held by assessment (1986). A total of 11 mineral sites were found and examined during the U.S. Bureau of Mines investigations; 26 mine workings were examined. Of the 11 sites, four are within the study area, and seven are nearby. Of the seven nearby sites, six are adjacent to the west boundary and consist of precious-and base-metals bearing vein occurrences in metamorphic rocks. The seventh site is near the east study area boundary, and consists of a tungsten-bearing vein occurrence that is also in metamorphic rocks. The four sites within the study area consist of vein occurrences in metamorphic rocks that contain silver, gold, arsenic, lead, zinc, and copper. The veins at these four sites are too small and low grade to be classified resources; however, there are indications that three of the sites may have silver and gold resources at depth. Detailed delineation of the veins, and determinations of tonnages and grades are needed. This would entail additional mapping and sampling, trenching and drilling, and opening inaccessible workings.

Jan 1, 1987

By Martin Hertzberg

This Bureau of Mines report analyzes diverse observations of the rates and mechanisms for the pyrolysis and devolatilization of coal and polymethylmethacrylate (PMMA). New data are presented for PMMA, together with new morphological evidence for the microscopic structure of the pyrolysis and devolatilization wave front in coals. It is concluded that there is no substantive evidence to support the traditional viewpoint that the pyrolysis and devolatilization rate process occurs isothermally, under chemical rate control; or is described realistically by a classical, unimolecular Arrhenius function of temperature. Instead, the reaction process occurs as a highly nonisothermal, heat-flux-driven, pyrolysis and devolatilization wave front, whose speed of propagation is predictable by internal heat transport constraints. Except for the complication of its charlayer residue, whose increasing thickness insulates the pyrolysis wave front from the heat source flux that drives it, both coal and PMMA behave similarly during pyrolysis and devolatilization. For PMMA, decomposition occurs at a temperature of 3500 to 5500 C; for coal it occurs at 4500 to 6000 C. There is no evidence that the reactant temperature ever exceeds those values regardless of the source temperature to which the samples are exposed.

Jan 1, 1988