Search Documents

By F. S. Wartman

The presence of magnetite, either dissolved or suspended as solid crystals, in slags from the copper reverberatory furnace is a frequently mentioned cause of an abnormally high copper content in those slags. The presence of this oxide in the slag is to be expected, since it is present in appreciable amounts in both converter slag and roaster calcine which comprise a considerable proportion of the furnace feed. Magnetite is also a product of some of the furnace reactions. These abnormal losses result in several ways. Magnetite is supposed to favor the formation and retention of copper ferrite, in the slag. Crystals of solid magnetite suspended in the slag are objectionable-because they make the slag less fluid and often entrap globules of matte. Frequently these crystals settle into a layer at the slab-matte interface which may have such mechanical strength as to create a false bottom and interfere with furnace operation by preventing separation of matte from slag. Magnetite may, by crystallizing on the furnace bottom, build the bottom to such a level that the furnace can no longer be operated.

Jan 1, 1928

By B. K. Shibler

A highly flexible laboratory-scale fluidized-bed reactor was designed, constructed, and successfully operated continuously at temperatures up to 1,300° C during an investigation of thermal methods for decomposing gypsum. This report discusses briefly the many problems encountered in developing the 10-inch-diameter reactor and describes its design and construction in sufficient detail to enable other research organizations to build a comparable unit. The reactor consists of a 10-inch-inside-diameter vertical tube which can be varied from 6 to 10 feet high; it is formed from 2-and 3-foot sections of silicon carbide pipe. The tube is surrounded by a 3-inch heating space formed by an outer 4.5-inch-thick circular wall of insulating firebrick. A cone-shaped fluidizing chamber is bolted to the bottom of the reactor. Fluidizing gas enters through the bottom of the cone, and ore is introduced by means of a screw feeder connected to an inlet located just above the gas port. A silicon carbide overflow tube of 1.25-inch inside diameter extends upward into the reactor. The depth of the bed is controlled by substituting different lengths of overflow tube. Twin dust-recovery systems, each composed of a cyclone and Fiberglas filter, are attached to two gas outlets at the top of the reactor tube. The reactor is designed for research on both exothermic and highly endothermic reactions. It can be fired externally by means of four natural gas burners that jet tangentially into the annular space at the base of the reactor. Alternatively, it can be fired internally, using a mixture of air or oxygen and natural gas as the fluidizing medium. A separate instrument panel contains flowmeters, manometers, an automatic program controller, and a multiple-point recorder for printing a record of the temperatures measured by thermocouples located at critical points in the reactor.

Jan 1, 1963

By J. D. Ramsdell

The study described in this report was undertaken to obtain information on the character and effect of antimony additions to titanium. The availability of high-purity, low-hardness titanium metal, resulting from fused-salt electrorefining techniques, permitted a reassessment and evaluation of the physical behavior of titanium-antimony alloys. Alloys, based on several grades of titanium containing up to 10 percent antimony, were arc-melted and processed to sheet by hot and cold rolling. Properties and characteristics were evaluated by hardness tests, hot and cold rollability, annealing treatments, metallographic examination, and tensile tests.

Jan 1, 1960

By David E. Emerson

An improved method and apparatus for determining the impurities in helium by preconcentration and subsequent analysis by mass spectrometry are described. Preconcentration of the impurities is accomplished by passing a known volume of helium, at slightly above atmospheric pressure, through a metal coil and trap assembly immersed in liquid helium. The concentrated impurities are then analyzed by mass spectrometry. This method can detect impurities in the range of 0.01 to 600 ppm with an accuracy of better than ±0.05 ppm at the 1-ppm level. One operator can analyze 15 samples in an 8-hour day.

Jan 1, 1970

By James F. O?Neil

Brown iron ore deposits in Quitman County, Ga., were investigated by the Federal Bureau of Mines in cooperation with the State of Georgia, Department of Commerce, and the University of Alabama. Ninety-one holes were drilled, having an aggregate footage of 2,188 feet; seventy-one holes penetrated 248 feet of iron mineralization. Average thickness of the ore zone was 3.5 feet under an average thickness of 14.7 feet of overburden. The drilling developed inferred reserves containing nearly 30 million long tons of crude ore with an average analysis of 28 percent iron plus minor quantities of manganese. Test work done by the Bureau on the crude ore samples indicated that they would upgrade by current lug washer practice, with the use of a 1i8-inch screen, and yield 4.4 million dry long tons of concentrate with an average analysis of 52.1 percent iron plus manganese. The weight recovery obtained was 14.7 percent. Research studies made by the Bureau showed that the weight recovery would be increased by changing the screen size without any appreciable sacrifice of grade. The average weight recovery was increased to 18 percent with a 10-mesh screen and 22.8 percent with a 20-mesh screen. Screen tests studies indicated that there was no appreciable interlocking of the iron and manganese minerals and the clay and silica waste particles of the materials retained on a 200-mesh screen. Clay was prominent in micron-size slimes. Silica was deleterious in the minus 20-mesh size.

Jan 1, 1965

By S. J. Broderick

[The term "nonmetallic minerals? as commonly used is the mining industry, refers to those minerals of industrial importance that are mined essentially for uses other than for the metals contained. The field comprises several hundred rod minerals of industrial importance, of which 70 have can adequately described in the textbook Industrial Minerals and Rocks. A few o f the more important nonmetallic products are sand and gravel, salt, phosphates, clays, refractories, limestone, and cement materials. Some of the minerals, such as bauxite and pyrolusive, have both metallic and nonmetallic applications, but in this report only the nonmetallic mineral phases are considered. In the organic field of nonmetallics only coal is considered, as, the others - petroleum, natural gas, natural bitumens, and hydrocarbons - are of no importance in water softening.]

Jan 1, 1941

By R. W. Huber, R. C. Wiley, V. C. Petersen

"Three arc- melted ingots, two of a t itanium-7 percent manganese all oy and the third of unalloyed titanium, were forged and rolled into 3/ 4-inch plate; comparative data were obtained on these processes. The finished plate, part of which was used by the Naval Bureau of Ordnance, was tested for mechanical and other properties.These properties were correlated with sponge purity, forging technique, rolling temperature, and cooling rate from the rolling temperature. For the alloy material, transformation data were obtained, and their age-hardening characteristics were studied. The temperature-impact relationship was established for rolled sections from all three ingots.INTRODUCTIONArc -melted ingots of unalloyed titanium and a titanium-manganese alloy were fabricated into plate under closely controlled conditions by personnel of the Metals and Alloys Section, Physical Metallurgy Branch, Bureau of Mines, College Perk, Md. This program was cosponsored by the Naval Bureau of Ordnance. Bureau of Mines interest lay in correlating the processing procedures with the mechanical properties of the finished plate.Considerable data have been published recently on constitution diagrams and properties of titanium-manganese alloys in genera1. 3/ 4/5/6/ However, little if any correlation between processing schedules and end results has been published, particularly with respect to the present commercial production of the proprietary titanium manganese alloys . Several factors in the production of titanium and titanium alloys have a pronounced influence on the physical and mechanical properties of the finished product: (1) The degree and nature of impurities in the base materials, ( 2) the amount of impurities introduced during the melting cycle and their distribution, (3) the homogeneity of the alloy, (4) forging, (5) rolling, and ( 6) final heat-treating cycles. All of these item£ are important from a metallurgical standpoint in producing the desired end properties in the metal."

Mar 1, 1955

By Richard F. Hewlett

Numerous populations of assays have been simulated for a range of assay values representative of low-grade mineral deposits to facilitate the study of problems encountered in evaluating these deposits. Analysis of these simulated populations of assays (obtained by using statistical probability models for the simulation) makes possible the quantification of the effects of (1) various composite assay intervals, (2) ore reserve computational methods, (3) uneven assay intervals, and (4) various cutoff grades on both the precision and the accuracy of the estimated average grade and tonnage of ore.

Jan 1, 1964

By David E. Nicholson

This report investigates the mechanical behavior of fine soils in a lunar environment in engineering gravity-flow bins. The ultrahigh vacuum, absence of moisture, and a lunar gravity one-sixth that of earth gravity represents a unique environment, both advantageous and detrimental to these systems. On earth, moisture and gases contained in powder masses can be responsible for complex descriptions of gravity flow. Their absence appear to simplify the lunar soil behavior. However, simulation of the lunar gravity and vacuum complicates the development of experimental data for designing bins. The properties of a dry soil powder, its behavior under one-dimensional compression, and its torsional and direct shearing strength under earth atmosphere are described in part 1 of this paper. These properties provide the parameters for a finite-element analysis to optimize the design of bins, to be described by Dr. William Pariseau in part 2. Shear tests assess the failure criteria for the material. Compression tests provide modulus and (Ko) stress-ratio values from the loading portion of the compression cycle, duplicating the condition of a bin at rest with the discharge closed. During the unloading portion of the compression cycle (soil overconsolidated), the residual Ko values rise. It is postulated that this phenomenon creates a high-lateral stress in bins when they approach incipient flow. Assessment of the Ko value, overconsolidation ratio, and the void ratio state is proposed as a criterion to determine the flowability of powder.

Jan 1, 1971

By Daniel R. Babich, Jeffrey R. Vipperman, Eric R. Bauer

Prolonged exposure to loud noise can cause permanent damage to the auditory nerve and/or its sensory components. Despite regulations and efforts by government and industry to reduce noise-induced hearing loss (NIHL), it is still a problem in the U.S. coal mining industry. The Mine Safety and Health Administration noise standard (30 CFR3 62), which was enacted in September 2000, is aimed at reducing NIHL in the mining industry. To address NIHL in various aspects of coal mining and provide the necessary information to effectively implement control technologies, the National Institute for Occupational Safety and Health conducted a cross-sectional survey of noise sources and worker noise exposures. Noise surveys consisting of full-shift worker noise exposure (dose) determination, time-motion studies (task observations), and equipment and/or area noise profiling were completed in 8 underground coal mines, 10 surface coal mines, and 8 coal preparation plants. The studies revealed that more than 40% of all workers monitored were subject to noise exposures above 90 dBA TWA8. A summary of these studies is presented, their application to administrative and engineering controls is discussed, and exposure reduction methods are reviewed.

Jan 12, 2006

By B. W. Gandrud, G. D. Coe

"INTRODUCTION The Bureau of Mines, United States Department of the Interior, with the cooperation of the University of Alabama and coal producers of Alabama, is making a series of washability studies to obtain technically and commercially important data from the productive coal beds of the State. Based on the system followed in these studies, this report consists of screen-sizing and sink-and-float data on the America and Pratt beds at Gorgas, Ala.SAMPLING AT THE MINESAlthough operations were discontinued in 1929, the accessible openings of the old Gorgas mines of the Southeastern Fuel Co. made possible the taking of samples from the America bed at three openings and from the Pratt bed at two openings. A sample was taken from the America bed at the Klondyke opening; a second was taken about 1 rile south of the Klondyke at the Musgrove America opening, and a third sample was taken about 1-1/2 miles south of the Musgrove-America at the Cricket Lodge opening. A sample was taken from the Pratt bed at Musgrove-Pratt No. 1, which is about 3/4 mile east of Musgrove-America, and a second sample was taken at Musgrove-Pratt No. 2, which is about 3/4 mile west of Musgrove-America. The samples ranged in weight from 1/2 ton to 1 ton and were equivalent to approximately a 2-ton sample from each bed. Figure 1 shows sections of the beds at the places sampled.In addition to the samples for washability study, a seam sample for analysis was taken at each of the places sampled. So as to give a representative seam sample for each of the two beds, these samples were combined in the laboratory in proportion to the thickness of the bed at the places sampled."

Jul 1, 1939

By B. W. Gandrud

At the Southern Experiment Station of the Federal Bureau of Mines, reports are prepared from time to time on results of washability studies of commercially important coal beds in the Southern Appalachian region. The investigations that provide the material for these reports are made by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the mine operators. This report records the results obtained on a sample of run-of-mine coal taken in June 1953 from the Pratt bed at the Davidson Coal Co. mine about 1 mile west of Graysville, Ala. One of the main objectives of a washability study is to obtain technically and commercially important data in connection with the best methods for preparing and utilizing the Nation's limited reserves of good coking coal. Such information is important from the standpoint of conservation in that it facilitates selection of preparation methods that will yield an acceptable grade of coking coal with a mini-mum of losses of coal in the rejects. The Pratt bed is one of the main sources of coking coal in the Jefferson County part of the Warrior field. This is the first time, however, that data from a complete washability study of coal have been obtained from this bed in Jefferson County. In the Graysville area, Pratt-bed coal has good coking characteristics and is used for blending with other coals in making metallurgical coal. The extent of its use in such blends is severely limited in this area, however, by the fact that it has a high sulfur content, which has not been reducible to any great extent by washery treatment.

Jan 1, 1955

By W. D. Mcmillan

During the fall of 1943 the Bureau of Mines put down four churn-drill holes totaling 435 feet of bore at the McGregor zinc lead mine near Potosi, Washington County, Mo., after the property had been examined by John Soule, an engineer of the Bureau, in the fall of 1942. A small production of lead and barite ore had been maintained at this property for many Years from shallow deposits in residual clays. A few shafts had penetrated the underlying dolomites and exposed a network of narrow fractures containing galena, sphalerite, barite, and marcasite. The drilling by the Bureau tested conditions at depths ranging from 80 to 130 feet. This report sets forth the data resulting from the work.

Jan 1, 1948

By William Eathorne

"INTRODUCTION Retsof mine, adjoining the village of Retsof, Livingston County, New York, is about 5 miles northwest of Geneseo and 55 miles (air-line distance) due east of Buffalo. It is a single-bed rock-salt mine having extensive horizontal workings as much as 2-1/2 miles long and 1 mile wide and has been in continuous operation since 1885. Retsof tine is the largest producing salt mine in North America and is reputed to be the largest active salt mine in the world.Retsof is one of three large salt mines operated by the International Salt Co., Scranton, Pa.; T. Forster Courthope is general manager of Retsof and also of the company's Detroit salt mine in Michigan and has held that position for 27 years. He is assisted by Stanley Martin, general superintendent; R. Goetz, Maintenance superintendent; and John Riordan, mine superin¬tendent. All are old-timers at Retsof and, according to Courthope, contri¬buted the ""lion's share in bringing the mine to its present standard of safety.ACKNOWLEDGEMENTThis circular was made possible by the generous cooperation of T. Forster Courthope and his assistants, Stanley Martin, R. Goetz, and John Riordan. The information and time generously given are gratefully acknowledged.GENERAL INFORMATIONThe rock salt as mined contains about 99 percent sodium chloride and requires only crushing and screening to prepare it for the market. With the exception of a large jaw crusher underground, all crushing is done in a mill building attached to the headframe of the main hoisting shaft (fig. 1).Five sizes of salt are produced, ranging from about 1/2 inch diameter down to minus seven mesh."

Sep 1, 1949

By David C. Oyler

The U.S. Bureau of Mines studied the interaction of longwall shield supports and adjacent strata at the Meigs No. 31 Mine in southeastern Ohio. Twenty-three legs of twenty shields at midface were instrumented with pressure transducers and monitored for 11 weeks. During the project, leg setting pressures were reduced twice to determine the effect of setting pressure on shield-strata interaction. No correlation was observed between setting pressure and leg loading rates. The shield loading profiles were consistent with a model in which the roof consists of two zones, a thin immediate roof loading the shields well below the typical setting force and a main roof zone essentially supported by the coal and gob and loading shields through its convergence. This model was used to develop an equation for estimating average loading rates at the site. The only variable of the equation is time, and the equation consists of an exponential term to account for the immediate roof loading and a linear term to account for main roof loading. The equation gave good correlation with average loading rates, but the variation in loading from cycle to cycle was too great for the equation to give good predictions of individual cycle loading rates.

Jan 1, 2010

By J. E. Chilton

The U.S. Bureau of Mines has developed an intrinsically safe carbon monoxide (CO) monitoring system for mines by coupling a fiber-optic data telemetry (FODT) system with a prototype electro-chemical CO monitor. The CO monitoring system can be used in a coal mine as one component of an early fire warning system. This system may be used in belt haulage entries when the entries are used for supplying ventilation air to working places. The FODT accepts a 0.1-to 1.1-V analog signal from the monitor and converts it to pulses (0 to 5 V) at frequencies from 1.1 to 11 kHz that drive a light-emitting diode (LED). An electrically nonconducting fiber-optic cable carries the LED signal to a remote receiver. The receiver analyzes the incoming light signal and displays the measured CO concentration in parts per million. This report discusses the performance of the FODT system and characteristics of the CO monitor such as response times, linearity, and temperature and pressure effects.

Jan 1, 2010

By J. D. Ramsdell

The purpose of this investigation was to determine the effects of the impurities, oxygen, nitrogen, carbon, and iron (in low percentages) on the mechanical properties of electrolytic titanium. The strength and hardness of binary Ti-O, Ti-N, and Ti-C alloys are linear functions of alloy content in the composition range investigated. Compared to oxygen and carbon, nitro-gen is the most effective strengthener and hardener, followed by oxygen, then carbon. When the carbon concentration is above 0.10 percent, carbides are present, and strength and hardness are relatively unchanged. For equivalent hardness levels, Ti-Fe alloys are stronger than binary titanium alloys containing oxygen, nitrogen, or carbon. However, the strengthening is related to the presence of transformed beta in the structure.

Jan 1, 1960

By T. D. Moore

Methane emission from two surface gob-degasification boreholes was measured by the Bureau of Mines. The investigation took place during mining of a 3,200-foot longwall panel in the Lower Kittanning coalbed in central Pennsylvania. The first hole was 500 feet from the start of mining, and the second hole was 2,200 feet. The first hole went on natural draft as soon as the longwall face passed it. This caused the methane flow in the return entries to drop 75 pct. In the 6 months required to complete the panel, the two holes emitted 69 MMcf of methane in varying percentages of concentration in air. In 3 years, the holes emitted a total of 150 MMcf of methane.

Jan 1, 1976

By N. S. Dalal, X. Shi, P. M. Gannett

"Chromates are known to induce tumors (1, 2), mutations (3), and DNA damage (4-6). However, the underlying biochemical mechanism(s) is (are) not fully understood (6). Recent studies have indicated that hydroxyl (·OH) radical may play an important role (7-11). The mechanistic studies of Cr(Vl)-related ·OH radical generation in biochemical systems have shown the reaction of a Cr(V) species with hydrogen peroxide (H20 2 } through a Fenton-like mechanism to be one of the important steps (9-11): Cr(V) + H20 2 - Cr(VI) + ·OH + OH-. (1)In biological systems the Cr(V) species are generated via the reduction of Cr(VI) by a variety of components, such as microsomes (12), mitochondria (13), mitochondrial electron transfer complexes (14), and at least three flavoenzymes (glutathione reductase (GSSG-R),3 lipoyl dehydrogenase, and ferredoxin-NADP+ oxidoreductase) (9, 15, 16). In the case of flavoenzymes, Cr(V) formation is accompanied by the reduction of molecular oxygen ( 0 2 ) to H20 2 • The Cr(V) species then reduces H20 2 to generate •OH radicals and Cr(VI) (16).To understarid the mechanism by which Cr(V}-generated ·OH radicals cause cytotoxicity, Aiyar et al. (8) investigated the reaction of Cr(VI) and H20 2 to generate ·OH radical and its reaction with 2'-deoxyguanine (dG) to form 8-hydroxy-2'-deoxyguanine (8-0HdG}:"

Mar 1, 1992

A PRELIMINARY PROGRAM, dated April 25, 1974, was prepared for Development Engineering, Incorporated (DEI) on research and development laboratory, field and other engineering studies for the disposal of retorted oil-shale materials. This PRELIMINARY PROGRAM included a discussion on the peculiarities of the retorted shale materials to be investigated and a discussion of the various laboratory and field tests which would need to be conducted to define their physical and chemical properties. The PRELIMINARY PROGRAM was divided into eight work phases as follows: I -- Program Development II -- Exploratory laboratory tests on old USBM retorted shale III -- Laboratory tests on pilot plant retorted shale. IV -- Laboratory tests on retorted shale from the semi-works plant and field test plots and ponds. V -- Field compaction tests. VI -- Infiltration pond tests VII -- Bureau of Mines special tests.

Jan 1, 1975