Search Documents

By Oliver Bowles

Enormous quantities of limestone are used for metallurgical purposes. Approximately 23 million tons were so used in the United States in 1925 chiefly for smelting iron ores in the blast furnace. Smaller amounts are used in basic open-hearth steel manufacture, and in smelting lead, copper and antimony ores. Most limestone producers lave little knowledge of the way in which their stone is used in metallurgy. Maximum tolerances of silica, alumina, sulphur and possibly magnesium; and minimum content of calcium carbonate may be arbitrarily fixed for the guidance of the producer, but aside from these requirements little information is available to producers on the manner in which their stone is used, the office it performs in smelting, or the effects of impurities. More complete [wledge] of utilization would enable limestone operators to solve their production problems more intelligently.

Jan 1, 1927

By B. H. Eccleston

Experimental data were obtained from two medium-duty diesel engines derated to qualify for use in underground mines. Gaseous and particulate emissions from these engines were measured and results provide information on the effect of exhaust treatment devices on the emissions. The devices in the study were a catalyst, a particulate trap, and an exhaust gas cooler of the water scrubber type. Emission levels of carbon monoxide and hydrocarbons were observed to be very low in comparison with emission levels of comparable engines in full-rated operation. Oxides of nitrogen and benzo(a)pyrene content of the exhaust also were found to be somewhat low in comparison with previous findings. For particulate reduction, the combination of a particulate trap and a scrubber was observed to be the most effective combination tried; in some cases, over 60 pct particulate reduction was effected by the trap-scrubber combination.

Jan 1, 1981

By Peter G. Kovalchik

To compare the viability of the new fuse wire arc test (FWAT) as a substitute for the comparative tracking index (CTI) for determining surface resistance to electrical tracking, the Bureau of Mines constructed a fuse wire arc tester and undertook a detailed testing program for testing insulating materials used on explosion-proof enclosures. This report describes the Bureau's apparatus, the two methods (CTI and FWAT), and the results of the Bureau's testing, showing comparisons of the FWAT with the CTI. Results showed strong correlation between the two methods, as all specimens tested that had CTI ratings of 400 V ac rms and above passed the 10-test sequence with the FWAT, whereas all specimens with lower CTI ratings failed, with the number of tests to failure corresponding roughly to the descending CTI rating order.

Jan 1, 1987

By Charles A. Kumbe

"INTRODUCTION The Sullivan Mine was examined by Thomas L. Chapman, an engineer of the Bureau of Mines, in March 1943. Samples taken from the few mineralized exposures justified further investigation of the property. To determine whether extensive exploration of the property would be warranted, the Bureau did a small amount of trenching and underground work during April 1943, 3/ under Bureau project 1462.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its, primary objective the, more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratary project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurigical Branch, R. G. Knickerbocker, chief, analyzes samples and performs beneficiation tests.The investigations of the and Metallurgical Branches of the Bureau, as reported in this paper, were supervised by J. Hedges, district engineer for Arizona, and S. R. Zimmerly, regional engineer for the Western Region, respectively."

Feb 1, 1947

By Thomas H. Dubaniewicz

The National Institute for Occupational Safety and Health, Pittsburgh Research Laboratory, conducted a study of past mine explosions to identify the ignition locations and ignition sources responsible for the most severe explosion events resulting in death. Since the Scotia disaster of 1976, many fatalities from underground coal mine explosions have been linked to nonpermissible electrical equipment ignition sources located in intake air courses. With few exceptions, explosion protected equipment is generally not required in intake air courses of gassy underground coal mines in the US. Cigarette lighters were another prevalent ignition source for fatal explosions ignited in intake air courses. Several mine rescue/ recovery teams have encountered electrical ignition hazards. The study provides evidence that intake air courses of gassy underground coal mines fit the description of certain Hazardous (classified) locations described in the US National Electrical Code®. Class I Division 2 or Zone 2 explosion protection tech¬niques may be used to design intake air equipment so that it does not present an ignition source under normal operation, before mine power is shut down in emergency situations. Nonpermissible circuits in intake air courses that are likely to remain energized during emergencies, e.g. battery powered equipment, should be protected by more stringent Class I Division 1, Zone 1, or Zone 0 techniques, to protect rescue/recovery personnel.

Jan 1, 2009

By Robert W. Freedman

In the Bureau of Mines study, a filter with a 20-by 20-inch-square cross section was inserted into the exhaust ducting of a 4-stroke-cycle, 90-hp diesel engine, and the efficiency of removal of total particulate was measured gravimetrically as a function of time. Removal efficiencies were close to 90 pct during the main portion of several extended runs employing several combinations of filter beds. Variations in engine load had little effect on collection efficiency. Particle size as measured by a Bureau-developed online instrument centered on 0.07 m based on number count. Removal efficiency increased rather sharply for both larger and smaller particles.

Jan 1, 1979

By H. Kenworthy

The objective of this investigation was to evaluate the technical feasibility of smelting certain low-grade domestic iron ores in an electric furnace. Laboratory-scale experiments showed that a high recovery of iron in the form of pig iron can be obtained from east Texas ores containing less than 25 percent iron. The pig iron was amenable to standard-or electric-furnace-refining methods for producing steel. Car-bon, silicon, and phosphorus were the primary impurities removed in refining. Overall recoveries of iron as pig iron exceeded 95 percent, in contrast with commercial mineral-dressing recoveries on these particular ores of 50 percent of the iron as a 45-to 50-percent iron concentrate.

Jan 1, 1958

By W. H. Ode, W. A. Selvig

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County Colo., in connection with a survey of carbonizing properties of American coals 4/ and investigations of their chemical and physical properties. 5/ The coal represented by the sample from Weld County was reported to give off combustible volatile matter at unusually low temperatures when placed on a fuel bed. The yields of tar and oil and the composition of the as from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

May 1, 1937

By Arcy P., D&apos Banister

Several gold-antimony geochemical anomalies were outlined near Stibnite, Idaho, using the humus sampling technique. Several hundred reconnaissance humus samples were collected and analyzed by a combination fire-assay atomic absorption method. The results partially outlined several gold-antimony anomalies and are very encouraging for further work in this part of Idaho.

Jan 1, 1970

By William O. Vanderburg

Tis paper describing the mining practices at the Cold Springs mine of the Wolf Tongue Lining Co. at Nederland, Colo., is one of a series of similar papers prepared by the Fureau of kines on mining practices, methods, and costs at various mines in the United States. The writer acknowledges the assistance of William Leach and William T. Todd, manager and mine superintendent of the Wolf Tongue Mining Co., respectively, in the preparation of this paper.

Dec 1, 1932

By Michael Horn

This report presents a structural analysis of the economies of Spokane County, Washington and 21 surrounding counties. An economic trading region made up of 22 eastern Washington, northern Idaho, and western Montana counties, with Spokane, Washington as the central place, was defined for this study. The Micro IMPLAN modeling system with the 1990 county database was used to create an Input/Output based model of the regional economy. The leading industries, with respect to employee compensation, employment, value of exports, and total industry output are shown for each county and the region. The value of total industry output from natural resource based industries is also shown (or each county and the region. The total industry output from the Spokane Economic Trade Area (S ETA) region is valued at $22.3 billion. The SETA region provides $7.1 billion in employee compensation to a work force of 374,000. Spokane County, Washington accounts for about 50 percent of the regional total output, employee compensation, and employment. Both Spokane County and the region as a whole produce about 80 percent of total industry output for final demand with the remaining 20 percent going to intermediate inputs for further production. About $7.4 billion of the $22.3 billion SETA output is exported from the region. Spokane County exports about $4.7 billion, or 41 percent of the $11.5 billion Spokane County output. Exports account for more than 50 percent of the total output in 12 of the 22 counties within the region. Based on the output of the top 25 industries in each county and the SETA region about 9 percent of the industry output from Spokane County and 18 percent of the regional industry output come from natural resource based industries. For counties other than Spokane County, total industry' output from natural resource based industries represents from 12 percent to 81 percent of county output from the top 25 industries. Natural resource industries account for more than 50 percent of total county output in 8 counties within the region

Jan 1, 1994

By J. Dean Warner

In 1984, as part of a project to evaluate Alaskan occurrences of certain critical and strategic minerals, the Bureau of Mines investigated a columbium-bearing regolith on upper Idaho Gulch, near Tofty, AK. The regolith is derived from weathering of a dolomitic marble and consists mostly of iron oxide minerals with accessory apatite, zircon, xenotime, rutile, monazite, and the columbium minerals aeschynite, columbite, and ilmenorutile. Two regolith lenses contain 340,000 lb of columbium resources at an average grade of 0.07 pct. Calculated composite concentrates from two regolith samples (approximately 200 lb each) contained 53 and 57 pct of the columbium at grades of 0.97 and 0.86 pct, respectively. In each case the grade could be improved to 1.1 pct Cb with a sacrifice of 9-pct recovery. The regolith's mineralogy, trace-element geochemistry, and similarity to descriptions of other columbium-enriched regoliths suggest that the underlying marble may be a carbonatite. The lack of associated alkalic igneous rocks and the stratiform nature of the regolith, however, may be interpreted as evidence for sedimentary origin of the marble. The marble and regolith are a lode source for some of the minerals in the Idaho Gulch placer deposit.

Jan 1, 1986

By A. T. Coumbe

The first national survey covering sales of fuel oil by States and principal uses was made in 1926 by E. B. Swanson of the Bureau of Mines (then under the U. S. Department of Commerce) under a cooperative agreement with the American Petroleum Institute. This annual study, covering the market for fuel oil, was made through 1930 with the financial help of the institute bat has since been continued by the Bureau up to the present time. The scope and coverage of the survey have gradually changed over the years as new uses for fuel oil have been found and new products have come into importance resulting in market expansion. Range oil (No. 1 fuel oil or kerosine) came into use for cooking and space-heating daring the depression era in New England, and it was first reported as a total in the 1931 survey. In 1934 the sales were compiled on a State basis. State totals for distillate fuel oil, Diesel fuel, and residual fuel-oil sales were first shown for 1934 and by principal uses and States in 1937. Kerosine deliveries by States and main uses were also released for the first time in 1937.

Jan 1, 1952

By Harold E. Heide

Although the United States has been the largest consumer of tin, only a small quantity of tin was produced or. the North American Continent during peace times, and thy deficiency was made UP by foreign imports. Because the most important sources of tin wore cut off by the war with Japan, it became necessary to increase imports from South America and Africa and, if possible, develop domestic tin reserves. Most of the tin produced in North America has come from the Seward Peninsula, Alaska, and a substantial portion of this was produced from the Potato Mountain area. Tin was first identified as occurring in the Seward Peninsula by A. H. Brooks in 1900, when a part of heavy concentrates from Anikovik River and Buhna Creek, one of its tributaries, proved to be stream tin. 4/ His report was given considerable publicity by the daily press, and the first steamers north in 1901 carried a number of prospectors bound for the Seward Peninsula to search for tin. The deposits of stream tin on Buck Creek in the Potato Mountain area were discovered in the fall of 1901. 2/

Jan 1, 1949

By Gerald T. Homce

A system capable of monitoring a mine electrical power system to detect incipient electrical component failure could significantly improve power system safety and availability. The U.S. Bureau of Mines funded a contract with The Pennsylvania State University (Penn State) to establish the theoretical and technical framework for such a system. This report briefly outlines the contract, reviewing related Bureau and Penn State work prior to its award, and describes support work carried out by the Bureau. The main focus of the report is on research efforts by Penn State and subsequent results. An existing algorithm for incipient-failure detection and classification was studied, and recommendations are made to improve its performance. In addition, mathematical models of cable-connected motor systems and deteriorating motors were developed and implemented on computers. These models and laboratory tests were used to study and document relationships between component deterioration and electrical terminal effects. The project was supported by the U.S. Navy and the nature of its interest in the application of failure prediction techniques is also included.

Jan 1, 1989

By T. Bieniawski

"INTRODUCTION The Congress theme ""Improvement of Mine Productivity and Overall Economics by Modern Technology"" is probably beat: addressed by the subtheme allocated to this Plenary Session. It is appropriate that .Theme 1 emphasizes the simple point that effective use of geotechnical information is the key to improving mine productivity. In essence, this means that: (1) geological and geomechanics, (rock mechanics) data must be collected in sufficient quantity and of high quality; (ii) data interpretation must be performed specifically for purposes of engineering design; (iii) innovative design approaches should be used to bring about Improvements in productivity and safety.While, each of these three aspects .may: seem obvious to any mining engineer it is a fact that the above sequence is seldom followed and as a result, mining engineering not infrequently lags, behind other branches of engineering when it comes to design creativity, efficiency and safety.. . After all, mining is still-one of the most hazardous occupations and we are gathered here to discuss, at the highest world professional forum, how to use more effectively the modern technology. This however, does not mean that mining engineers are less capable than other engineers or that their achievements are any lesser; far from it! Mining engineers are the cream of the engineering society on whose efforts depends the welfare of mankind. Moreover, they have produced minerals and coal evergrowing quantities against evergrowing difficulties. Yet, we must and can become even better because we are not making full use of the modern technology and rock mechanics knowledge already at our disposal, and. we are not being innovative enough to the full extent of .our capabilities."

Jan 1, 1989

By I. O. Salyer

This research was conducted with the objective of suppressing the respirable dust in coal mines by foam application. A formulation was developed for making a water-based, high-expansion, and limited stability foam. A horizontal boring machine was used as a laboratory coal mining model for generating coal dust. A modified laboratory foam generator was built. Foam was applied directly to the point at which dust was being formed by the cutter of the boring machine working against a block of coal. Coal dust was sampled with an impinger and analyzed for the particle count and particle size distribution. Coal dust suppression test results on freshly generated dust have demonstrated very clearly that in laboratory scale experiments over 90% of the respirable coal dust can be suppressed by foam. These tests were run when initial coal du t concentrations were 10 and 70 million particles per cubic foot (mppcf).

Jan 1, 1970

By James A. West

The South Asian countries of India, Pakistan, Afghanistan, Ceylon, Nepal, Bhutan, and Sikkim arc to varying-degrees just beginning to achieve significant economic and industrial development. These countries are richly endowed with certain mineral resources, and development of these resources is being accelerated. In 1965, the mineral industry remained a relatively small sector of the region's economy, accounting for only about 1 percent of its estimated gross national product of $62,528 million. Nevertheless, the estimated $630 million total value of minerals produced in South Asia during 1965 represented an increase of nearly 15 percent t over that of 1964. India continued as the dominant mineral producer of the region, accounting for 85 percent of the total value of all minerals produced ill 1965. India increased its output of iron ore, manganese, mica, coal, and petroleum. Pakistan accounted for 13 percent of the value of the region's output and recorded increased output of iron ore, chromite, coal, natural gas, and most other minerals. The small mineral industry of Ceylon attained remarkable growth in the production of ilmenite, graphite, and gem stones. The mineral industry of Afghanistan remained relatively insignificant, although development of large known resources of natural gas was continued, Nepal, Bhutan, and Sikkim produced no commercially significant quantities of minerals in 1965.

Jan 1, 1967

By John R. Benham

The West Pioneer RARE II study area, No. 1-006 (fig. 1), has Figure 1.--NEAR HERE a high molybdenum resource potential. Two molybdenum-bearing areas are being explored by Utah International and by Cyprus-Moly Corp, Inc. using geophysical exploration and diamond core drilling. The study area also contains potential resources of gold and silver at six prospects: the Bear Paw (Ibex), Black Bear, Coeur d'Alene, Franklin No. 1, Martin, and Maynard. In addition, the Black Rear and the Martin contain possible copper, lead, and molybdenum resources. Most of the workings are caved.

Jan 1, 1981

By Allen D. Look

Use of two-way radio communication at the Santa Rita open pit of the Kennecott Copper Corp. has furnished a satisfactory answer to the problem of communications for an operation covering an extended area. Coordination of operations has resulted, with little loss of time in making changes during the shift. Repairs are facilitated, and safety of operations is increased through better control of blasting and hazardous conditions. INTRODUCTION Expansion of mining operations brings increasing needs of improved communications to coordinate the mechanized operations that contribute to the efficiency of present-day open-pit methods. Equipment found satisfactory when first installed becomes inadequate as distances and demands increase. It is the, purpose of this paper to record the progress being made by one mine in meeting this problem.

Jan 1, 1952