Search Documents

By M. R. Geer

Three coals from the Wilkes on - Carbonado district of Pierce County , Washington , were subjected to washability analyses to estimate the amount and quality of washed coal obtainable . Because the coals were unusually difficult to clean , the washability examinations were supplemented by table tests , tests in dense - medium cleaning units , and flotation tests . None of the coals could be reduced to the desired 10 percent ash by tabling and the response to flotation by two of them was poor . Dense -medium treatment provided coal of the desired quality , but with the most difficult coal the recovery efficiency was lower than usual .

Jan 1, 1964

By Philip C. Tully

This Bureau of Mines report contains experimentally determined vapor-liquid equilibria data for a helium-nitrogen-methane mixture with a nominal composition of 15, 60, and 25 mole-percent, respectively. Measurements of the equilibrium phase compositions were obtained by means of a windowed cell, in conjunction with an automated chromatograph and a special analyzer for low helium concentrations. The data presented include a comprehensive table and eight graphs depicting phase compositions, vaporization ratios, and correlations with a previous study of two helium-nitrogen-methane mixtures of different compositions.

Jan 1, 1976

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1952 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 94 samples of aviation gasoline which include, for the first time in this series of reports, data on five samples of grade 108/135 aviation fuel. Data also are given for 34 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers? production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 20 manufacturers of aviation gasolines and of 16 producers of aviation jet fuels are represented.

Jan 1, 1953

By Murray Jacobson

Data obtained by the Federal Bureau of Mines on the dust explosion hazard in air are presented for 220 samples of agricultural products. Information is given on ignition temperature of dust clouds and layers, minimum explosive concentration, minimum electrical energy for ignition, explosion pressure and rates of pressure rise, amount of inert dust required to prevent flame propagation, and, in a few instances, the permissible oxygen concentration in an atmosphere to prevent ignition by spark and by heated surface. The effects of particle size and source of sample on explosibility are shown. The relative ignition sensitivity, severity of explosion, and overall explosibility of the materials are characterized by empirical indexes. This report contains Ma obtained by the Bureau in laboratory studies on the explosion hazards of agricultural dusts. Recognition of the dangers will encourage adoption of adequate measures to prevent ignition and explosion during preparation, processing, and utilization of the materials. Agricultural products constitute one of the largest groups of materials used in America. More than 260 million tons of various grains, much of which now exists in dust form, was grown in 1958.6/ Over 600,000 tons of the annual production of 200

Jan 1, 1961

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1963 to June 30, 1964 are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1964; in general; the research reported in these publications antedates the report period. Part 3 describes a short-term investigation into safety problems associated with shipping of molten sulfur; this investigation is not at present destined for publication elsewhere.

Jan 1, 1965

By Farrel W. Lytle

Instrumental analysis has become an indispensable tool in research and production of the rare-earth elements. This development can be attributed mainly to a combination of two factors--the marked chemical similarity of the rare-earth elements, which excludes classical methods of analysis, and the speed and accuracy of instrumental-analysis techniques. With continued improvements in methods of producing high-purity rare-earth elements, keeping pace instrumentally is becoming much more difficult. Accordingly, greater emphasis is being placed on improving instrumental limits of detection and accuracy. The methods employed most frequently for determining impurities in rare-earth elements involve use of the optical-emission spectrograph (3, 4)4/ and the spectrophotometer (9). Although numerous X-ray-emission spectrographic methods (6-8) have been developed for analyzing rare earths, these techniques have not included detection of low-level impurities. This investigation was conducted to find the precision and accuracy of X-ray fluorescence in deter-mining impurities in rare-earth oxides in the 0.01-to 1.0-percent-concentration range.

Jan 1, 1959

By G. V. Sullivan

This report summarizes the results of a preliminary study concerning manganese extraction from low-grade dolomitic materials from the Philipsburg district in Montana by the Dean-Leute ammonium carbamate process. Studies were made to determine the relationship between the variables involved in treating these materials by a roast-leach process and the amount of manganese extracted. The variables studied were the roast temperature, the roast particle size, the molar ratio of NH3 to CO2 in the leach solution, the liquid-solid ratio in leaching, the leach time, and the size of the particles being leached. The roast-leach studies were statistically designed, and the experimental results were evaluated by an analysis of variance.

Jan 1, 1962

By Charles L. Parsons, R. B. Moore, S. C. Lind, O. C. SCHAEFER

Early in 1912, from information received by the Bureau of Mines, it became evident that quantities of valuable radium-bearing ore from Colorado were being exported for manufacture in foreign coun- trics and that at least part of the manufactured product was being returned to this country and sold at a price entirely incommensurate with that received by the miner and the prospector. Consequently, in line with its efforts to increase efficiency in the mining and treat- ment of mineral resources, the Bureau of Mines undertook an inves- tigation of conditions. Results of this preliminary investigation were published, in the summer of 1913, as Bulletin 70, which gave an out- line of the radium deposits of the West, the conditions of mining, the wastes involved, and the status of the production of radium from its ores. At about this time newspapers and medical journals were publish- ing statements regarding the value of radium in cancer therapy. These reports, although many of them were exaggerated, brought out clearly the remarkable virtue of the gamma rays for the treat- ment of cancer and other malignant growths. In view of the fact that the largest known supplies of radium ore in the world are in the States of Colorado and Utah and on the public lands of the United States, it was deemed highly important for the Bureau of Mines to study the production of radium in detail. Such study, it was hoped, would enable the prospector and miner to obtain a fairer price for the ores and would furnish information necessary in case Congress appropriated funds to develop methods for extracting radium from ore on the public lands under Government supervision, to be supplied at cost to the hospitals of the Army, Navy, and Public Health Service.

Jan 1, 1915

By Thomas C. Mowatt

Chemical and petrographic studies were carried out on selected tin-bearing rock samples of contact-metasomatic origin from the Cassiterite Creek and Brooks Mountain areas, Seward Peninsula, Alaska. The tin content of rocks ranged from 0.39 to 8.9 pct. Leaching with a 20 pct hydrochloric acid solution released from 19.3 to 67.9 pct of the tin. Cassiterite was not observed in the rock samples. These results are significant with regard to tin recovery and reserve delineation in these and similar occurrences. Part of this leachable tin may be associated with metasomatic borate minerals.

Jan 1, 2011

By Foster Fraas

The Bureau of Mines investigated a method for calculating values of adsorption energy; the goal was to devise an equation consistent with experimental data accumulated in the investigation of adsorption as related to ore separation processes. Numerical identification of the constants of a previously formulated equation provided an equation by which values of adsorption energy could be calculated. Values thus calculated checked with those obtained by calorimetric measurement.

Jan 1, 1965

By I. L. Nichols

Volatilization of cesium from pollucite ore was investigated as an initial step in the production of purified cesium metal or cesium salts. High recovery of cesium and rubidium as chloride sublimates was accomplished by 2-hour roasts in a tube furnace using charges containing 1 part ore, 2 parts limestone, and 0.23 part calcium chloride. Recoveries of cesium in the sublimate product were 89.1, 92.9, and 95.2 pct, respectively, using 1,100° C and vacuum, 1,250° C with an air sweep, and 1,250° C without an air sweep. Most of the lithium, sodium, and potassium sublimed with the cesium and rubidium, but virtually none of the calcium, aluminum, and silicon in the charges was volatilized.

Jan 1, 1966

By R. V. Ramani

This volume is the third of a four-volume final report on research carried out under a contract from the U.S. Bureau of Mines on the development of a computer simulation model for surface mine reclamation planning. The other volumes are titled as follows: Volume I: Ore Reserve Estimation, Volume II: Dragline Model, and Volume IV: User's Manual for OPMHS/2. The Mine Coordinate Generator System serves as an interface between the Geology and Reserves System (Volume I, final report) and OPMHS/2 (Volume IV, final report) to provide local mine grid information which is used as input to the decision making process and dynamic simulation routines of OPMHS/2. After the Geology and Reserves System has been successfully run for a property, a data base containing values for each grid cell covering the property is created at the end of execution, if chosen as an option by the user. The Mine Coordinate Generator reads this information and creates a special direct access data set from the sequential data input. When information defining the mine grid is read, the values present in the property grid are for the interpolation of values for each mine block.

Jan 1, 1985

By D. B. Gawthrop

"One of the properties of an explosive, of interest to the user, is its ability to transfer detonation across an air gap to another explosive charge. This Property is of particular importance with permissible explosives used in coal mines, since they are relatively insensitive to detonation when compared to many of the commercial dynamites used in metal mining.An essential characteristic of an explosive is that it shall always be sufficiently sensitive to propagate detonation completely. An insensitive explosive constitutes a hazard because of (1) the danger of drilling into unexploded portions of charges of explosives which have partially misfired, and (2) the likelihood of a low order of detonation, or the burning, of all or part of the charge in a hole prepared for blasting. The latter condition not only usually produces large volumes of poisonous gases, but it is particularly hazardous in gassy or dusty coal mines where explosions may result.The Bureau of Mines and manufacturers of explosives determine the sensitivity of explosives to detonation over an air gap by means of a [(halved-cartridge gap test,"" for which the ends of the cartridges of explosive exposed to one another, are cut off. Since in blasting, the crimped ends remain on the cartridges used, this investigation has been made to ascertain the effect of the crimped paper ends on the distance detonation is propagated over an air gap as compared with the propagation distances obtained when the crimped-paper ends are removed."

Nov 1, 1932

By H. B. Humphrey, F. E. Cash

The Birmingham coal-mining district of Alabama has many local physical conditions that contribute largely to the proble of preventing coalmine fatalities . Coal : nes of Alabama have been under the supervision of the State mine inspector since 1892 , and reports have been made with increasing completeness since that time . The U. S. Bureau of Mines has maintained a station of the safety division in the district since 1912 to cooperate with operators and the State in the advancement of safety in mining . A description of conditions in regard to fatal accidents as they have been and as they now are in Alabama , compared with the entire United States , will indicate the progress that has been made and that should still be made in reducing fatal mine accidents .

Sep 1, 1930

By R. R. Sayers, W. J. McConnell

"The health, comfort, and efficiency of men engaged in the mining industry may be impaired, in some instances very seriously, by abnormal physical conditions of the mine air or by variations in its composition. This is true in some of sheet metal mines of the West where high temperatures with varying humidities are encountered. Physiological studies have been made in some of these mines showing the effects of various temperatures end humidities. As it is difficult to carry out studies on many controlled temperatures, it was thought best to make the experiments in a laboratory and apply the results to the industry insofar as practicableThe effects of moderately high temperatures and humidities are more difficult to measure perhaps than the extreme conditions, but may be predisposing causes of fatigue, discomfort and disease, A cooperative study of the physioloical effects of heat and humidity is being conducted by the Bureau of Mines and the U. S. Public Health Service cooperative with the American Society of Heating and Ventilating Engineers, in the Research Laboratory of the Bureau of Mines at Pittsburgh, Pa."

Mar 1, 1924

By R. V. Ramani, W. Miola

"A relationship exists between the quartz contents in the underground coal nine airborne dust samples and those in the coal and host rocks that are mined [17, 18, 19] The prescribed method for quartz analysis in respirable airborne coal dust samples is the MSHA P-7 method. Accurate quartz analysis procedures are needed for bulk samples in order to predict the potential quartz content in airborne nine dust, which in turn will aid the design of quartz dust control procedures during mining. thereby reducing the airborne quartz dust in underground atmospheres. The requirements of this method are that the amount of quartz is the sample be less than 250ug, and the total sample weight less than 2,500 ug. Unlike with airborne dust samples, there are no limitations to the available mass of bulk samples. However, these are no standard procedures for the preparation of bulk samples for scanning or prescribed methods for quartz analysis. The NIOSH and MSHA methods are certified for roped* dust and the acceptance of these methods for bulk samples assumes that the bulk samples will be reduced to the conditions specified for respirable dust samples. An alternative method is X-ray diffraction, which provides higher average quartz values than those obtained from P-7 method for the same samples.An investigation was carried out to determine the optimal procedure for preparing the bulk samples for the IR and XRD analyses. In this paper, the investigations on the effects of calibration, particle sizes, matrix composition, interferrous, and behavior of the filter substances on IR, XRD and FTIR results are presented. The error introduced by the presence of kaolinite and a new sample asking procedure to reduce it are discussed. The problems experienced with conventional sample holders for scanning were eliminated with the design and development of a new hollow sample holder. Quantitative comparison of quartz determinations by IR, XRD and MR methods on coal, roof and floor rocks, and airborne dust samples are presented. The important factors affecting the results of quartz analysis methods are: 1) bulk sample preparation for obtaining representative and homogeneous analysis samples: 2) particle size distributions of the analysis samples and calibration standards; 3) qualitative matrix composition of the analysis sample; 4) matching calibration standards to analysis sample; 5) substrates for sample deposition during analysis sample preparation; 6) procedures for analysis sample mounting; 7) selection of proper portions of she response profile for insanity measurement; and 8) interferences of spurious phases with the critical analyses. The recommendations of this study are important to enable comparisons and interpretations of analysis and research results."

Nov 1, 1995

By S. A. Matthes

This Bureau of Mines report describes analysis of a copper slag for 13 elements from a single sample solution by flame atomic absorption spectroscopy. Samples are dissolved with 7 ml of an HC1-HF-HN03 (3:1.5:2) mixture in heated plastic pressure vessels. A 1.5-pct boric acid solution is added to dissolve precipitated fluorides and to reduce matrix effects that interfere with atomic absorption analysis. Preparation time is less than 1 hour per batch of 10 samples. Total analysis time is less than 6 person-hours for 130 determinations with an average relative standard deviation of 1.83 pct for the 13 elements. Simple acid standards were used for all determinations. Values obtained by this method are in excellent agreement with values obtained by slower, more costly procedures.

Jan 1, 1980

By Manuel Gomez

Carbon number distributions were obtained for tar acid fractions from five low-temperature tars by low-ionizing voltage mass spectrometry. Quantitative data for phenols representing seven structural compound types were examined by statistical analysis. It was shown that for the phenols discussed, the data could be represented by regression equations expressing phenolic concentration as a function of the reciprocal of the carbon number and the carbon-to-hydrogen ratio of the parent coal. The total concentration of each structural type present was found to depend on the molecular weight and boiling point of the initial member of the group. Carbon distribution data for the tar acid fractions studied support the view that low-temperature tars contain the same chemical compounds but in different proportions.

Jan 1, 1965

By Thomas L. Vandergrift

This U. S. Bureau of Mines (USBM) report evaluates three stress-transfer-modification concepts for their potential in reducing longwall gate road stresses and closures. In each of the three concepts - packwalling, gob infilling, and entry filling -support structures are constructed on the headgate side of the panel parallel with or inby the face line. When the headgate becomes the tailgate of the adjacent panel, these structures are in place to accept stresses transferred from the mined-out panel. Using the USBM nonlinear boundary-element program MULSIM/NL, baseline models of typical longwall stress transfer behavior were developed for both intermediate depth and deep mining conditions. These models were verified by comparing model results with field measurements and observations. The stress-transfer-modification concepts were then incorporated into the deep baseline model to quantify the effects of each concept on tailgate closure. Modeling results indicated that entry filling is the most effective concept in reducing tailgate escapeway closure. Using only 18 m3 of a weak fill per meter of face advance (7.3 yd3 per ft of face advance), tailgate escapeway closure was reduced by 33%. By improving the quality of the fill, similar results were achieved using 50% less volume.

Jan 1, 2010

By V. Vallyathan, Xianglin Shi, N. S. Dalai

While Cr(VI) is a known carcinogen, the underlying biochemical mechanism is still not fully understood (1). In a pioneering study Jennette (2) utilized electron spin resonance (ESR) spectroscopy to demonstrate that a long-lived Cr(V) species is generated during the reduction of Cr(VI) by microsomes in the presence of NADPH. Later Wetterhahn and co-workers (3, 4) showed that incubation of chromate with isolated rat liver mitochondria causes the reduction of Cr(VI), as well as the formation of a Cr(V) species. Analogous Cr(V) species have also been detected in the reduction of Cr(VI) by other cellular systems such as Hanserulla polymorphared (5) and blood cells (6, 7). All these as well as other studies (8-12) have suggested that this Cr(V) species plays a significant role in the mechanism of Cr(VI) toxicity. Thus far, however, the chemical structure of this dominant Cr(V) species formed in cellular systems has not been identified, and this observation provided an impetus for the present investigation. Another reason for undertaking this study was that some recent reports (10-16) suggest that hydroxyl ('OH) radicals may also play an important role in the mechanism of Cr(VI) toxicity. In particular, it has been shown that OH radicals are formed in reactions between Cr(V) species and H2O2 (13-16), and that the radical yield depends on the chemical structure of the Cr(V) species (15). For example, while Cr(V)-diol complexes efficiently generate OH radicals, another Cr(V) species, the tetraperoxochromate (CrO3/8) ion, does not (15). Thus in the present study, we focused our attention on the following: (a) structural identification of the Cr(V) species generated in the reduction of Cr(VI) by subcellular as well as cellular systems, using microsomes, mitochondria, and Escherichia coli; (b) possible detection of OH radical in the same systems since there is no earlier report of chromium-mediated generation of 'OH radicals in a cellular system; (c) possible involvement of molecular oxygen in chromium-related OH radical generation since a recent report (17) indicated that Cr(VI) mutagenesis is strongly oxygen dependent; and (d) elucidation of the mechanism of OH radical formation in these systems.

Mar 1, 1992