Search Documents

By S. R. B. Cooke, J. Bruce Clemmer, F. P. Diener

"The limestone deposit utilized by one of the plants of the Universal Atlas Cement Co. is covered in part by a stratum of cherty limestone. If this overlying deposit could be utilized by removing the excess of chert economically, quarry costs could be reduced and the amount of rock economically available would be increased greatly. On account of the distribution of flint and limestone, a product fairly free of flint can be obtained until the quarry face is about 50 or 55 feet high. As the face is worked farther back into the hill, the comparatively clean stone is overlain with a constantly increasing amount of high-flint limestone. If this flint remained with the limestone, there would be a prohititively high silica ratio in the finished cement; if the flinty layer were removed as overburden a very large tonnage would be handled and much good stone lost. Consequently it was felt that means should be devised for separating the flint from the limestone after it reaches the plant.The investigation was undertaken by the Mississippi Valley Experiment Station of the United States Bureau of Mines in cooperation with the Universal Atlas Cement Co. and the Missouri School of Mines and Metallurgy, Rolla, Mo.CONSIDERATION OF PROCESSESMany schemes for the separation of Minerals are based on differences in the specific gravities of the minerals to be separated. In this case the flint has a specific gravity of approximately 2.62 while the limestone averages about 2.70. This differential is not large enough to permit separation by any method based on specific gravity. Furthermore, all the limestone particles in any given sample are not alike; usually about 10 percent of them have a specific gravity the same as, or lower than, the flint."

Mar 1, 1935

By Russell R. Trengove

In order to extend or delimit the known ore reserves adjacent to the Comet Coalition property on the western slope of the Highland Peak Range about 8 airline miles west of Pioche, Nev., the Bureau of Mines undertook an exploration project of diamond drilling. Production figures from this property, formerly known as the Schodde, are not available, but it has been reported that small amounts of rich silver and gold ore were Shipped by wagon to a smelter in the Salt Lake valley during 1900-1910. Small shipments were reported for the period 1915-1927, also. A study of the Pioche District by the Federal Geological Survey in 1942 and 1943 was the basis for the exploration program of the Bureau of Mines in 1947 This program consisted of diamond-drilling three holes. The total footage was 2,967 feet. No. 1 hole was drilled 1,260 feet, a record depth for diamond drilling in the Pioche District. Silver-bearing lead-zinc sulfide ores are found in the Combined Metals limestone, known locally as the C.M. bed, These deposits have been formed by replacement of the limestone that is inclosed in the Pioche shale.

Jan 1, 1949

By H. M. Cooper

Many analysts have had difficulty in obtaining accurate and consistent determinations of the volatile matter in low-temperature coke when the usual standard method for coal was followed. The tendency is toward too-high results, due to mechanical losses which are extremely difficult to avoid or control. With cokes there also may be an error due to excessive oxidation of the fixed carbon. Much of the earlier experimental work on the volatile-matter determination in coal, such as that of Parr, Fieldner and Davis, and others, has been on the effect of time, temperatures, shape and size of crucibles, method of applying heat, and type of furnace, all of which data has evolved the present A.S. T. M. standard method for volatile matter in coal and coke. It is not the purpose of this investigation to deal directly with the above phases of the procedure, but rather to study some of the factors affecting the results in those types of fuel which give erroneous results due to mechanical losses. This mechanical loss is usually designated as "sparking." There are two kinds of sparks or incandescent particles which may appear: particles of soot from partially condensed carbon from the burning gases, and unburned particles of the material itself which escape. The first type does not affect the accuracy of the volatile matter results, and is therefore negligible. The second type, however, causes appreciable loss and results in showing higher volatile percentages than actually exist.

Jan 1, 1932

By J. D. Marchant

In the spring of 1953 a series of heats were made using a 3-phase, size ST, Pittsburgh Lectromelt arc furnace to develop a method suitable for melting, refining, and granulating cobalt powder produced by the Calera Mining Co., at Garfield, Utah. According to specifications stipulated by General Service Administration, the granules had to pass a 2-inch screen and be retained on a 6-mesh screen, be low in phosphorus and sulfur, and contain a minimum of 98.7 percent cobalt plus nickel. Various combinations of water temperature, water jets, and rate of pouring were tried early in the campaign to produce desirable granules. It soon became evident that a properly refined and deoxidized molten bath was the major requirement for a satisfactory product. The physical characteristics of the granules were improved also if, just before pouring, the surface of the molten metal bath was pre-pared by a method involving the use of silica flux. The Bureau processed 107,750 pounds of cobalt powder. A total of 104,810 pounds of cobalt granules meeting General Service Administration specifications was returned to the producer. The refining slag, which was also returned to the company, contained 1,781 pounds of metal.

Jan 1, 1955

By R. R. Schehl

The Bureau of Mines analyzed the structure of a high-grade metallurgical coke, carbonized at different temperatures in the range 500° to 1,000° C, through X-ray diffraction studies. Growth in the crystallite size with increasing coking temperature was calculated from profile analysis and compared with values obtained from the radial distribution function. The carbonization temperature appeared to have little influence upon the stack height, whereas the layer diameters more than doubled in size between 500° and 1,000° C. These results are comparable to those obtained from other studies of poorer quality cokes.

Jan 1, 1974

By R. S. Fowkes

Jetstream pressure distributions and coal cutting rates were determined for a number of nozzles and under different operating conditions. The jetstrearn pressure distribution data were fitted to an assumed curvilinear equation by the utilization of a numerical least-squares technique with the aid of a digital computer. Subsequent manipulation of the approximation equation showed that the total force of the jetstream, rather than its maximum pressure or total kinetic energy per unit Lime, was the most significant quantity affecting the coal cutting rate. A shorter method for assessing the ability of a nozzle to cut coal was found.

Jan 1, 1968

By L. G. Trudell, J. W. Smith, K. E. Stanfield

Oil- yield data are presented for 40 sets of core samples and 83 sets of drill cuttings collected in 1952-62 from drilling operations in the Uinta basin of eastern Utah . This accumulated information on the location , extent , and richness of oil shales of the Green River formation is used to appraise the deposits as a source of oil and related products . Core samples used in the study were obtained specifically for evaluating oil shale , and they were satisfactory for this purpose , except they did not completely penetrate the formation . The drill- cutting samples were inferior to the core samples and yielded more erratic results . Consequently, oil yields based on cuttings should be regarded as indicative , rather than definite , until substantiated by other means . In general , the oil- yield data indicate Green River oil shale in Uinta basin is not as thick or as uniform as that in the Piceance Creek basin of western Colorado . However , it is an important potential source of oil . Estimates that beds 15 feet or more thick that average 25 gallons of oil per ton represent at least 120 billion barrels of oil in place are supported by the recent oil- yield data .

Jan 1, 1964

By H. B. Humphrey, F. E. Cash

From 1900 to 1929 , 1,005 or approximately 30 per cent of all fatalities in the coal mines of Alabama were caused by fires or explosions of gas and dust . In the 3 -year period from 1927 to 1929 only 15 men were killed by these causes , a reduction from 30 to 9 per cent of the total . Notwithstanding this marked improvement , which is due largely to the efforts made by the State inspection department , the operators , and the Bureau of Mines to stamp out this type of disaster , Alabama still has more than its share of such fatalities which can and should be prevented. A list of explosions from 1894 to 1929 compiled from information obtained through the records of the State Inspector's office , the reports of Engineers of the Bureau of Mines , and the operators , is given in Table

Oct 1, 1930

By L. F. Willmott

The production operation of a Kerpely gas producer at Louisiana, Mo., is described. This unit, originally designed for airblown operation was modified to permit using oxygen in the blast in place of air. The first runs J for test purposes, were made in June 1950. After this, seven production runs were made and these are the subject of this report. Total gasification time was 245 days. In each run, Nut or Pea coke or mixtures of both at a rate varying from 1,700 to 2,300 pounds per hour was converted with oxygen and saturated steam to produce synthesis gas - primarily carbon monoxide and hydrogen -approximating a predetermined rate of 80,000 to 95,000 cu. ft. per hour and a predetermined hydrogen-carbon monoxide ratio, The requirements per 1,000 std. cu. ft. of (CO + H2) were 21.6 to 30 pounds of coke, 213 to 267 std. cu. ft. of oxygen, and 3L4 to 47.B pounds of steam.

Jan 1, 1955

By L. H. Banning

In the fall of 1953 the Philippine Bureau of Mines, under a Foreign Operations Administration Technical Assistance (FOA-TA) program, began a systematic investigation of the nickel content of the well-known Surigao laterite areas, on the island of Nonoc northeast of Mindanao, to determine the occurrence, distribution, and grade of nickel contained in the laterite and in the subjacent serpentine. At the same time, a technical review of the possibility of producing commercial ferronickel from the nickeliferous materials in the Philippine Islands was made, and a smelting process was suggested. The proposed process would be similar to that developed by the Federal Bureau of Mines for the reduction of the nickeliferous serpentine occurring in the Nickel Mountain ?deposit at Riddle, Oreg. The potential avail-ability of electric power from the Maria Cristina facilities at 3 mils per kw.-hr. would enhance the economic possibility of this program. Development of an economically feasible process for recovering nickel from the nickeliferous serpentines and laterites should lead to the establishment of a new industry in the Philippines, to the development of a source of nickel in the Far East, of which at present there is none, and to partial solution of the problem of supplying the free world with nickel. Enough preliminary reconnaissance had been completed by early 1954 to permit sampling of the deposit for metallurgical investigations. The FOA then requested the Federal Bureau of Mines Northwest Electrodevelopment Laboratory, Albany, Oreg., to conduct preliminary electric smelting studies on nickeliferous serpentine and laterite samples.

Jan 1, 1955

By H. A. Doerner

For the past three or four years attention has been attracted to the deposits of lead vanadate in the Goodsprings , Nevada , district . Some ore running as high as 9 per cent 205 has been produced , but most of it runs from 0.5 to 3 per cent . Only a little ore , and that of the richer sort , has been shipped , since the low- grade ore will not stend the cost of shipment and no concentration mill has been available . Preliminary experiments indicate that chemical treatment of the low- grade ore without concentration is not feasible . Its treatment therefore involves two distinct problems ; first , mechanical concentration ; and second , a smelting or chemical treatment to obtain the lead and vanadium in marketable form . Upon this basis the work has been conducted . The writer wishes to acknowledge the excellent work done by J. T. Norton and Virgil Miller on table concentration and by J. E. Conley , who suggested and did preliminary work on the direct smelting method . Many helpful suggestions were received from Dr. S. C. Lind and John Gross of the Bureau of Mines . The ores were furnished by Mr. Frank Williams and Mr. James Ewing .

Jan 1, 1923

By John R. Bradley

The available supply of fuel and power is a subject of importance at all times and particularly at this time. The following brief survey of fuel and power in the United States appraises the extent of the several primary sources of energy the approximate monthly demand, 1929-40; the chief centers of production and consumption; and shifts in the principal uses from 1929 to recent years. The period covers the boom year 1929, the years of the great depression, the more normal year 1937, the recession in 1938, the year 1939, and 1940 (which was affected by armament programs). In some instances, the data for 1939 and 1940 are preliminary. The four primary sources of fuel and power are coal, petroleum, natural gas, and water power. Wood fuel, important in some regions, and foreign trade in natural gas and hydroelectricity represent a relatively small part of the energy supply and are not considered in this study. The tonnages shown are in terms of coal, based upon the calorific or B. t. u. equivalents of the several sources of power. In practice, the usable heat or energy varies according to the type of equipment available for its use. For example, the efficiency of turbine water wheels and internal-combustion engines is much higher than that of steam plants and household-heating devices.

Jan 1, 1941

The principal activities of the Bureau of Mines Explosives Research Center from July 1, 1963 to June 30, 1964 are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1964; in general, the research reported in these publications antedates the report period. Part 3 describes a short-term investigation into safety problems associated with shipping of molten sulfur; this investigation is not at present destined for publication elsewhere.

Jan 1, 1965

By David J. Kusler

This report describes a rapid, reliable, and relatively simple method developed by the Bureau of Mines Pyrometallurgy Laboratory at Bruceton, Pa., for determining lime (calcium oxide) and magnesia (magnesium oxide) in various materials containing these constituents in greater than trace amounts. Optionally, titania (titanium dioxide) may be determined for the same sample. The accuracy of the method, suitable for most purposes, is shown by comparing the Bureau results with those obtained by accepted procedures. The method has been applied satisfactorily to the routine analysis of blast-furnace slags, for which purpose it was primarily developed, and to other calcareous compositions. In the Pyrometallurgy Laboratory it has replaced the standard methods previously used to determine lime and magnesia, and has been in general use by that laboratory for the past several years. The analysis time, generally under 3 hours, is considerably less than required by standard methods.

Jan 1, 1960

By Timothy A. Clancy

In support of research on forming ceramics from mining and processing wastes, the Bureau of Mines tested various commercial refractories to evaluate their resistance to melts of these wastes. Sixteen refractories of various types were exposed in slag erosion tests to two siliceous waste melts with Si02/CaO ratios of 4.0 and 2.2, The extent and nature of slag attack were then determined for each refractory. The nature of slag attack was investigated through scanning electron micrographs and microprobe elemental distributions. The refractories that performed best in resisting attack by the melts were high-alumina types, and of the refractories tested, the most resistant was a 90-pct-Al203, 10-pct-Cr203 refractory.

Jan 1, 1983

By W. E. Anable

The Bureau of Mines studied the purification of commercially available vanadium in the 100-kw electron-beam furnace. Purification studies were conducted on a 100-gram button scale by melting and holding the liquid vanadium at temperatures ranging from 2,060° to 2,080° C at pressure of 5(10)-5 torr for periods ranging from 5 to 20 minutes. The effect of doping vanadium with carbon and metallic additions was determined. This study demonstrated that hydrogen was readily removed to 3 ppm or less, oxygen and carbon were reduced to less than 100 ppm each, and the metallic impurities were reduced Co the range of 10 to 500 ppm. The nitrogen content was not reduced in any of the buttons; rather, the nitrogen concentration generally increased as samples were held for successively longer periods. Oxygen was removed much faster and more completely when vanadium was doped with small carbon additions or one of several dopes prior to melting.

Jan 1, 1967

By H. H. Schrenk, W. P. Yant, P. H. Mautz

"In a study of the chemistry and pathology of chronic benzene poisoning, which was conducted cooperatively by the United. States Bureau of Mines, the Barrett Co., and the producers of benzene, it was necessary to make quantitative determinatious of the abzorption, distribution, and: fate of benzene in the organism. Although methods for determining benzene in relatively large amounts were available no satisfactory method was found for removing and determining the small amounts that are present in the tissues or excretions after exposure to conditions which ultimately cause chronic poisoning. This no doubt accounts for the lack of information in the literature on this particular phase of benzene poisoning.The writers have found in work that will be described in a subsequent publication that the amounts of benzene present in the tissues and excretions under conditions of exposure which produce chronic benzene poisoning arc of the order of a fraction to a few milligrams per 100 grams of tissue. This report describes a method developed and found satisfactory for these determina¬tions.RÉSUMÉ OF PERVIOUS METHODSA method for the determination of benzene in tissue was developed by Joachimoglu. 5 In the Joachimoglu procedure the ground organs are mixed with water and acidified with diluted sulphuzic acid, and the benzene is distilled into a receiver containing carbon tetrachloride. The benzene is nitrated in the carbon tetrachloride, the carbon tetrachloride evaporated, the acid mix¬ture neutralized, and the dinitrobenzene extracted with ether. After removal of the ether the dinitrobeuzene is determined gravimetrically. Joachimoglu reports that this method is about 55 to 60 percent quantitative."

Aug 1, 1935

By J. A. Cavallaro

To determine whether magnetite consumption could be reduced and salable coal production increased by using froth flotation units in series with magnetic separators, the Bureau of Mines conducted laboratory froth flotation tests on primary magnetic separator effluents obtained from three coal preparation plants. Tests were performed in a standard 500-gram-capacity laboratory batch flotation cell. Oleic acid and methylisobutyl carbinol were used as the collector and frother, respectively. Magnetite recovery was comparable to that expected from secondary magnetic separation, and salable float coal recoveries of 0,8 to 7.6 tons per hour were obtainable. The economics of the proposed technique appear to be sound.

Jan 1, 1966

By J. H. McClain

In the last 3 years' operation of the zirconium-production plant, zirconium metal has been employed to good advantage in many applications. The most frequent use has been in situations requiring resistance to attack by hydrochloric acid. In this service, it has been shown to be a serious competitor to Hastelloy. Zirconium also has excellent resistance to most other corrosives end could be considered for use as an all purpose metal. For example, this report cites 18 applications in hydrochloric acid, 4 applications in sulfuric acid, 5 applications in phthalic-hydrochloric acid, 3 applications in wet hydrogen chloride-chlorine atmospheres, and 2 applications in fused caustic.

Jan 1, 1954

By M. M. Tilman

The objectives of this research were to determine the practicability of using cobalt as a means of controlling the amount of ferrite in the micro-structures of semiaustenitic stainless steels, and to determine the effects of reduced ferrite content on mechanical properties of these steels. Cobalt additions of up to 3 weight-percent were made to type 17-7 PH2 (AISI 631) stainless steel. Ferrite contents were determined for alloys in the aged condition, and for alloys quenched from the hot working temperature. Ferrite can be completely eliminated from the microstructure of 17-7 PH stainless steel by additions of cobalt, but complete elimination of the ferrite phase results in lower tensile strength, yield strength, and hardness. Tensile properties, hardness, and impact strength were determined for aged material. A subzero temperature treatment before heattreating was necessary to obtain maximum strength in the alloys containing cobalt. Addition of 2 weight-percent cobalt enhances mechanical properties of 17-7 PH stainless steel.

Jan 1, 1968