Search Documents

By R. V. Ramani, R. Bhaskar

"The National Academy of Sciences (1) recognized the importance of studying the spatial and temporal characteristics of respirable coal mine dust atmospheres. In this paper, the progress to date of a research project on dust transportation and deposition in mine airways is presented. A mathematical model is proposed for studying the transport of dust. A source representative of dust generation in underground coal mining is defined. The influence and applicability of surface roughness, dispersivities, coagulation and reentrainment to vine dust flow arc examined. A convective-diffusion model is proposed for the transport and deposition of dust in mine airways. Using the model, the spatial and temporal characteristics can be evaluated in terms of dust concentrations in the mine atmospheres.INTRODUCTIONThe prediction of the behavior of fine particles Is Important in many fields of science and engi¬neering including physics, chemistry, mining, mineral processing, and atmospheric science. In mining from the health point of view, fine coal dust is associated with the appearance of pneumoconiosis in miners exposed to the dust. Also, in addition to being a nuisance factor obscuring visibility and general mobility of miners, it can lead to sudden catastrophic incidences of explosions. This paper outlines the progress to date of a research project on dust transportation and deposition in mine airways. A mathematical model is proposed for studying the transport of dust for the various mechanisms. The dust dispersion is defined in terms of a dispersion term determined from experimental data by Skubunov (23). Coagulation is considered as one of the mechanisms that can lead to changes in the particle size distribution. Reentrainment as a possible secondary source of dust was examined during model development but was not included in the final model."

Jan 1, 1988

By H. E. Powell

Magnetic susceptibilities were determined by the Bureau of Mines fur 19 cobalt- and nickel-bearing minerals and for a suite for synthetic cobalt-nickel diarsenides analogous to the rammelsbergite and safflorite series. Relations between susceptibility and composition were found to be nonlinear for both impure natural minerals and pure synthetics.

Jan 1, 1967

By E. A. Pelczarski

Initially, the objective of this contract was to develop a PWSCSR that could meet proposed criteria (that were different from 30 CFR 11(Title 30 of the Code of Federal Regulation part II) and that would be less than twice the size and weight of a filter self rescuer. This objective was met. Consequently, the original contract was extended to develop a PWSCSR that would meet existing CFR-30 criteria within the same size and weight constraints. This resulted in the development of a PWSCSR (the SR-100) that received NIOSH/MSHA approval (TC-239). This report presents a historical discussion of the design and development of the SR-100 as developed by CSE Corporation under Bureau of Mines contract number H0368013. The technical parameters and the test results of NIOSH/MSHA 30 CFR 11 certification are also presented.

Jan 1, 1990

By Brian R. Zelenka

The Bureau of Mines (Bureau) reviewed all available information regarding geologic and depositional processes contributing to potential coastal and offshore platinum group metal (PGM) placer deposits around the Goodnews Bay Mining District. The Bureau found that favorable environments for PGM along with gold and chromite enrichment include: (1) buried paleofluvial channels; (2) recent paleofluvial channels with little marine sediment overburden, (3) beach deposits, particularly in the upper swash zone and near back beach environments; (4) paleostrand lines; (5) shoal lag deposits inside the mouths of Goodnews and Chagvan bays; and (6) bases of far offshore tidal ridges which may represent reworked glacial deposits. Limited geologic and compositional (assay) data prevent determination of deposit size and grade of PGM mineralization for each deposit class. Future geologic sampling requirements for demonstration of identifiable offshore and beach PGM-bearing placers are discussed. Beach and offshore sampling programs conducted by the Bureau in 1986 will contribute additional information providing verification of specific deposit classes.

Jan 1, 2011

By George R. McCormick

Because several new and unusual synthetic minerals were found in the system MgO-MgF₂ - SiO2 with Li * , or Nat a similar system with Geo₂ replacing Sio , plus Lit was investigated . In addition to the expected compounds of germanium , Ge - fluor - hectorite and a Ge - fluor- chrysotile were synthesized . Protoamphibole was not observed . Data are given for 69 compositions prepared in the system MgO- MgF₂ - Ge02 at 6.94 percent LiF .

Jan 1, 1964

By J. E. Miller

This paper reports experimental determinations by the Bureau of Mines of compressibility factors to 4,000 pounds per square inch absolute (p.s.i.a.) for helium at temperatures from -10° to 130° F. and for 16 helium-nitrogen mixtures at 70° F. This information is needed for computing accurate discharge volumes and is necessary for determining an average-density value for use in orifice-meter formulas. In thermodynamic calculations, several functions of the compressibility factor with pressure and temperature are required. The data in the original publications (6, 8)5 of this study have been reexamined and have been given a more comprehensive treatment. The recalculated compressibility factors are higher by approximately 0.2 percent because in the earlier work a linear relationship between the compressibility factor of helium and pressure was assumed.

Jan 1, 1961

By Frank J. Wiebelt

In its efforts to maintain production of tungsten during the recent war period, the Bureau of Mines explored certain parts of the properties of the Atolia Mining Co. in San Bernardino County, Calif., by diamond drilling. Owing to past production record and other available data, the area was considered attractive for possible development of new ore bodies. Scheelite occurs in narrow veins ranging in width from a fraction of an inch to several feet. The veins are in quartz monzonite in a zone 2 miles long and 500 feet wide. Production from the district was reported to have been over 1,000,000 units of W03. Twelve diamond-drill holes, totaling 5,056 feet, were drilled by the Bureau of Mines in the vicinity of the Papoose, Papoose No. 5, Amity, and Union mines, the tailings pond, and the "Old Spud Patch." The work began in August 1943 and was completed in June 1944. This publication briefly describes the history and deposits of the district and gives full details of the work performed by the Bureau.

Jan 1, 1950

By R. Karl Zipf, Z. T. Bieniawski

"A set of fracture profile photomicrographs is presented for fractures generated under mixed mode loading of the Pittsburgh coal. The fractal dimension is used· to characterize the irregularity of these profiles and a tentative relationship is presented between the fractal dimension and the fracture toughness. Surface roughness appears to depend solely on the stress intensity and no other dependence was observed with fracture loading mode, loading rate· or specimen orientation. Observations of crack bifurcations.in fracture profiles can indicate crack growth direction whereas direct surface observations generally cannot in materials such as rock and coal.1 INTRODUCTIONThe production of fine fragments of material as a result of some loading event occurs in many industrial processes. In crushing and grinding, the efficient production of fine fragments is the desired end result; .however, in coal cutting, the production of fine fragments may lead to high levels of respirable dust in the immediate atmosphere with the danger of human lung diseases. Two of the most important sources of fragments in the 1 to 10 micron size range during a cutting process are 1) severe crushing in a zone near the loading tool and 2) subsequent shearing along major crack surfaces that form the larger fragments during material reduction. These and other sources of fine fragments generation are discussed by Roepke (1984) and Zipf and Bieniawski (1986). The physical character of the nearly created major crack surfaces is believed to have a strong influence on the amount of fine fragment generation that occurs during subsequent shearing movement. When the major large fragments initially form, they are ""locked"" in place by the irregular character of the new fracture surface. Only after some relative motion has occurred between fragments are they actually liberated, and the net result is the formation of additional fine fragments. The fine fragmentation is not necessarily limited to the shearing of high points from the macrocrack surf ace since material remaining in the wake of the crack tip is damaged to a substantial depth below the actual crack surface."

Aug 31, 1989

By BUREAU OF MINES

A complete list of permissible mining equipment, rescue apparatus and gas masks tested prior to July 1, 1928, was published in Bureau of Mines Information Circular 60772. The present list includes practically all equipment tested and, approved by the Bureau, up to and including Jan. 1, 1929. It covers electric air compressors, coal drills, mining machines, loading machines, conveyors, mine pumps, room hoists, mine telephones, rock-dusting machines, switches, electric cap lamps, flame safety lamps, electric hand and trip lamps, flash lamps, methane indicators and detectors, blasting units, storage barrery locomotives, tandem locomotives, power trucks, concrete mixers, self-contained oxygen breathing apparatus and gas masks. The system under which those devices were tested permits the manufacturer, after his equipment has passed certain tests prescribed by the Bureau of Mines, to mark his equipment with a seal shoring that it has been "approved" by the Bureau. These tests are designed to insure that the equipment has the minimum requirements for safety in use. The only object of the Bureau in making such tests and pub- lishing lists of permissible equirment is to safeguard the lives of workers and to help lesson the hazards of mining.

Jan 1, 1929

By Henry Kreisinger, John Blizard

This preliminary statement presents some of the results of tests carried out at the Lakeside Station of the Milwaukee Electric Railway and Light Co. , by the fuel section of the U. S. Bureau of Mines , in cooperation with the research department of the Combustion Engineering Corporation of New York . The object of these tests was to determine the thermal efficiency , ease of operation , and other particulars of a boiler equipped with specially designed furnace and burners for burning powdered coal . The boiler tested haş 13380 square feet of heating surface , and is one of eight boilers equipped with the Lopulco powdered coal system supplying steam to two 20,000 -Kw . steam turbines in the largest power house burning powdered coal . Twenty- six tests were run at rates of heat transference varying from 4000 to 8000 B.t.u. per square foot of boiler heating surface , and the mean thermal efficiency attained was about 84 per cent , based on the gross calorific value of the fuel as fired . The efficiency varied little with the rate of steaming , and its high value is accounted for by the small loss from incomplete combustion and the small amount of excess air which varied from 5 to 36 per cent . The coal burned had a gross calorific value of about 11500 to 12800 B.t.u. per pound , contained 2 to 5 per cent moisture , 33 to 36 per cent volatile matter and 9 to 13 per cent ash, and was so ground thaf 89 to 95 per cent would pass through a 100- mesh sieve . The ash had a softening point of 2150 to 2450 degrees F. , but did not fuse together at the bottom of the furnace because it was partly protected from the flame radiation by means of a series of water tubes connected to the boiler which were placed between the fumace bottom and the flame, ..

Jan 1, 1923

By John R. Bartels

This report discusses an improved method for rerailing underground railcars devised in a joint effort by the Bureau of Mines and Hoesch MFD. This improved method utilizes a lightweight hydraulic ram with hand-pump activation to move a bridge-mounted roller carriage in conjunction with steel-reinforced air-lift bags. This method provides a lightweight portable system in which only two workers are required to perform the mine car rerailing operation. Because of the very narrow confines in underground mines, use of overhead cranes and other surface rail techniques is not possible. This new system is designed for very low profile work, and provides the necessary lifting force from light- weight compressed-air bottles.

Jan 1, 1985

By P. M. Sullivan

This report describes a new application of electroamalgam metallurgy in recovering all the zinc as refined metal from galvanizers' sal skimmings. Pure zinc was recovered by electrolysis of skimmings leach liquors in amalgam cells. The following information was gained as a result of literature studies and subsequent laboratory investigations. 1. Reports in the literature indicate that pure zinc can be recovered from chloride solutions with the aid of amalgam cells. From Europe it was reported that amalgam cells could be used to recover pure zinc and chlorine from leach liquor obtained from pyrite cinders following a chloridizing roast.

Jan 1, 1956

By John G. Kovac

A computer simulation has been developed to estimate the chances of a miner making a successful escape while wearing a SCSR. The model takes into account: (1) training in the use of SCSRs, (2) apparatus integrity, and (3) the oxygen cost of a mine escape. This Bureau of Mines report examines survival odds for a prototypical escape, and illustrates how these odds change when SCSR training is improved.

Jan 1, 2009

By W. W. Simpson

The Bureau of Mines conducted research to determine the effects of potassium trithiocarbonate (KTTC), a degradation product of potassium ethylxanthate (KEX), on flotation of chalcopyrite and molybdenite. Small amounts of KTTC were identified in fresh and aged solutions of KEX using thin-layer chromotography. Hallimond tube flotation tests on pure minerals showed that KTTC acts as a weak collector for chalcopyrite. Both KEX and KTTC tend to depress molybdenite, but the depression effect is easily overcome by addition of a small quantity of fuel oil. The results of the Hallimond tube tests were confirmed in batch flotation tests using a porphyry copper ore.

Jan 1, 1983

By M. K. Quinn, N. P. Reddy, A. W. Khair

"An analysis of coal fragmentation due to the action of a continuous miner is presented. Underground coal cutting by a drum-type continuous miner was simulated in the laboratory using a specially designed unique automated rotary coal cutting simulator (ARCCS). The rotary coal cutter provided the versatility of varying the operating and in-situ parameters to provide information on the effects of generating 37 pm (0.0015 in) particles. In these tests, coal blocks with an approximate dimension of 50.8 x 35.6x 20.32 cm (20x 15x 8 in) were first subjected to confining pressures equivalent to in-situ conditions. The blocks were then cut by the rotary cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as (1) penetration of bit into coal, (2) penetration resistance (thrust and cutting pressures), (3) rotating velocity of' cutting head, and (4) acoustic emission activity in the coal block were monitored. During the test, all the cut products were collected for size distribution analysis. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using a camera attached to an optical microscope.The results led to a better understanding of the mechanisms of the fragmentation process during coal cutting and the effect of operating parameters, in-situ conditions and coal type on the size distribution of the cut product:"

Jan 1, 1989

By H. A. Watson

The introduction and use of synthetic materials in various applications may lead to potential hazards from toxic, gaseous, decomposition products if these materials are subjected to conditions abnormal to their intended use, such as high temperatures or burning from accidental causes. This report covers an investigation of such possible hazards from toxic gases produced by the burning or thermal decomposition of some low-density, expanded, synthetic materials, three of which consisted of polyvinylchloride and one of acrylonitrile. In the production of certain expanded plastic materials, Chemical blowing agents frequently are used to produce a cellular structure. One of these blowing or foaming agents contains azo-bis-isobutyronitrile, which is designated in this report as PN. Information indicates that a product of decomposition of this blowing agent, formed in the blowing operation, is tetra-methyl-succino-nitrile, designated as TSN, Which is significantly toxic. Decomposition of the blowing agent, with release of its azo nitrogen, is represented by the following reaction:

Jan 1, 1951

By Ann Hubbs, Vincent Castranova, Jane Y. C. Ma, De-Hwa Chao, Joseph K. H. Ma

AN OVERVIEW OF THE ACTION OF TETRANDRINE ON SILICOSISBecause of the persistent presence of silica dust in the lungs silicosis is a progressive and irreversible disease. At present, there is no proven effective therapy for silicosis. Limited choices of therapeutic intervention with corticosteroids and other immunosuppressive regimens 1,2 have been accepted for some forms of pulmonary fibrosis. These treatments are only minimally effective, and the results provide little understanding of the disease state due to the lack of correlation between drug activity and the mechanism of fibrosis. Thus, continuing effort must be made in the search for effective antifibrotic agents, which may be used to provide a sequential analysis of the fibrotic process and to open the door for further research and clinical development. Tetrandrine is one of hundreds of drugs screened for antifibrotic activity by Chinese scientists. It has been used in China as a treatment for silicosis in open clinical trials3 and in laboratory animals. The action of tetrandrine on pulmonary fibrosis has been attributed to its ability to inhibit particle stimulation of alveolar macrophages, a key cell type central to the fibrotic process, to release oxygen radicals and inflammatory cytokines. Alveolar macrophages (AM) residing on the alveolar wall, are the predominant phagocytic cells of the lungs responsible for pulmonary defense against inhaled microorganisms and other particles and thus play an important role in maintaining the homeostasis of the lungs. 7 Ample evidence suggests that cells of the monocyte-macrophage series play an important role in the immunopathogenesis of pulmonary fibrosis. When upregulated by silica, alveolar macrophages generate reactive oxygen metabolites8·9 which can damage lung parenchyma and release fibrogenic growth factors and cytokines, 10,11 such as interleukin 1 (IL-1), which can induce fibroblast proliferation and collagen synthesis. The cytokine-mediated fibroblast proliferation and collagen synthesis are key steps in the development and progression of pulmonary fibrosis .11 Previous studies by our group have shown that tetrandrine exhibits strong binding affinity to AM and inhibits particle-stimulated respiratory burst activity (oxygen consumption, superoxide anion release, and hydrogen peroxide secretion) in these cells. 13 In addition, studies by Kang et al. 14 have reported that tetrandrine inhibits silica-induced release of fibrogenic factors such as IL-1 which are capable of inducing fibroblast proliferation and collagen synthesis. Reist et al. 15 further suggested that the antifibrotic action of tetrandrine may be mediated in part by the direct effect of this drug on the ability of fibroblasts to respond to proliferative agents. These results indicate that the mechanism of silicosis involves activation of AM and fibroblasts by silica, resulting in abnormal collagen production due to miscommunications between the cell types. Tetrandrine may interrupt this process by direct interaction with the lung cells.

Jan 1, 1998

By David R. Hanson

Transient electrical noise events pose serious problems for data acquisition systems used in monitoring acoustic emissions in laboratory and field environments. The U.S. Bureau of Mines has designed and constructed a trigger discriminator circuit for use in ultrasonic acoustic emission studies. Designed for use with signals in the frequency range of 50 to 400 kHz, the instrument examines .incoming signals for frequency content, amplitude, simultaneity, threshold crossings, and number of channels above threshold. If preselected criteria on these properties are met, a plus 5-V pulse is output that may be used to trigger a data acquisition system, allowing rejection of noise events that do not possess useful information. The system was designed for four input channels, but may be expanded to more channels with minimal design changes.

Jan 1, 1995

By Lloyd Carpenter

Eighteen elements were determined spectrochemically in vanadium metal and its compounds in the general range of 1 to 1,000 ppm by means of spark-ignited unidirectional arc excitation. The samples were converted to vanadium pentoxide and combined with a mixture of graphite, lithium carbonate, and gallium oxide. For the molybdenum determination, the oxidized samples were mixed with sodium chloride and packed in copper electrodes. Average precision of the method was 15.6 percent relative standard deviation and relative error was 4.4 percent.

Jan 1, 1963

By N. F. LeJeune

[ ]

Jan 1, 1924