Search Documents

By G. L. Oldright

This paper is the twelfth of a series on smelting in the lead blast furnace and the fifth dealing with blast-furnace gases. It was noted in Report of Investigations 2957 that the gases evolved from the top of the lead blast furnace at Tooele were similar in composition to those from the top of an iron blast furnace. It was noted in Report of Investigations 3095 that at Kellogg, where a smaller percentage of coke on charge and shorter stock column were employed, the gases evolved were much less reducing. At times there was a considerable amount of oxygen in the top gases at the second plant. More SO2 was also evolved from sulphides in the charge. Then operations were conducted as at Kellogg, the gases were alternately reducing and oxidizing. This paper deals with the gases evolved in smelting a charge containing more zinc than at either of the other two plants with about the same amount of coke as was used at Kellogg,: To compare other factors influencing the composition of the gases, it may be noted that at Tooele the approximate height of the charge column was 15 feet, at Kellogg 9 feet and at Trail 13 feet. The furnaces have about the -same cross-sectional area- tog. The furnaces at Tooele are about 6 inches wider at the tuyeres, being 54 inches wide against 48 for the other two plants. At Tooele and Kellogg the furnaces are fed at the top from bottom-dump cars. At Trail the charges are dumped from Decauville cars (bottom cars which dump when tilted), which run on tracks placed on both sides of the blast furnaces. The hoods through which the waste gases are conducted are directly above the shafts of the furnaces. The flues for removing the effluent gases lead off from under the charge floor at Tooele and Kellogg. (Charging and distribution of the feed in the furnace covered later in a rate paper of series.)

Jan 1, 1934

By C. B. Barmore, B. W. Gandrud, B. M. Bird

"The Bradford mine of the Alabama By-Products Corporation is located in the Warrior coal field of Alabama, in the northern part of Jefferson County, about 25 miles north of Birmingham. The coal mined from the Black Creek bed at this point is not considered to be ideal for coke making by itself but because of its exceptionally low ash content is mixed with the higher-ash coking coals from other beds of the district to control the ash content of coking mixtures. Further reasons for using this coal only as a diluent of the higher-ash opals are that the thinness of the bed renders the production costs relatively high and the reserves are somewhat limited.This paper, which is the fourth of a series on the washability of Alabama coals, Like its predecessors dealing with the Mary Lee beds and the Clark bed,6 contains screen-sizing and float-and-sink tests of a representative sample of the raw coal, and flakiness tests showing the proportions of flaky particles in certain selected sizes. However, inasmuch as the float-and-sink tests of the coarse sizes showed excellent liberation of coal from impurities, crushing tests have not been considered necessary.The data on which this report is based have been obtained in connection with an exhaustive study of coal preparation in Alabama now being conducted by the U. S. Bureau of Mines and the University of Alabama with the cooperation of the different coal operators. As the work progresses other papers will follow containing further data on Alabama coals and giving results obtained in preparing these coals by various methods."

Apr 1, 1931

By P. L. Woolf, J. P. Morris, E. Foerster, G. R. Zellars

Measurements of vapor pressure can be used to determine the thermodynamic activities of the components of metallic solutions . The determination of activity by this method requires accurate values for the vapor pressure of the pure component and for its partial pressure above the alloy solution . This investigation was conducted to measure the vapor pressure of liquid manganese for use in future studies of the activity of manganese in various liquid alloys . In related investigations in the Bureau's Pyrometallurgy Laboratory , vapor pressures of copper , iron and nickel have been measured and activit 4 5 6 have been determined in the iron- copper and iron- nickel systems . Difficulties were experienced with manganese which were not encountered in the previous investigations . Manganese oxidizes readily and greater care was needed to maintain an oxygen- and moisture - free atmosphere in the furnace . In addition , liquid manganese wet the refractories and there was a tendency to foam and splash on introduction of the carrier gas . Because of these difficulties several variations in the experimental procedure were studied . These were first tested with silver which has a vapor pressure of the same order of magnitude as manganese but is relatively inert at high temperatures . Although no significant changes in the original procedure resulted from this work, considerable data were obtained for silver and have been included in this report . Bauer and BBrruunnnneerr7/ have reported the only extensive investigation of the vapor pressure of liquid manganese . However , their results are not consistent with the data obtained by McCabe and Hudson for solid manganese . Measurements of the vapor pressure of silver have been reported by McCabe and Birchenal1,2/ Schadel and Birchenall , 10/ Harteck , 11 / Fischer , 12/ and von Wartenberg.13 / Generally , these investigators conducted their measurements at lower temperatures than were used in this study .

Jul 1, 1960

By G. C. Branner

The bauxite diagram presented as figure 1 was developed to clarify, by graphic means, the theoretical chemical constituents of gibbsite-kaolinite-type bauxite for all possible proportions of these two minerals from pure gibbsite to pure kaolinite. The tables in the report reflect the same date. The diagram provides (1) a graphic representation of the relations of constituents with respect to a ill possible percentages of alumina and silica, (2) a basis for verifying the accuracy of analyses of gibbsite-kaolinite bauxite, and (3) a basis for estimating the type and proportion of alumina hydrate and/or silicate minerals that may be present in gibbsite-kaolinite-type bauxite. The diagram, with accompanying interpretations and use formulas, will be useful to those connected with the mining and processing of bauxite.

Jan 1, 1955

By Frank E. Cash

Accident prevention is an integral part of the operating procedure of the petroleum industry, and refinery officials and employees throughout the United States are exerting concerted effort to reduce the frequency and severity of accidents and are realizing definite results. In other words, the petroleum industry is safety conscious to a much creator decree than most of the other mineral industries. On January l, 1936, there were 11 operating, refineries in Louisiana with a crude-oil capacity of 199,750 barrels per day.4/ This report deals with safety in four of these refineries representing. 72 percent of the refinery capacity of Louisiana.

Jan 1, 1940

By Lindsay D. Norman

Four chloride and seven fixed-nitrogen processes for recovering manganese from domestic resources are described. The chloride processes are divided into two classes (leaching and chloridization) depending upon the major operation responsible for converting the manganese minerals to the chloride from which manganese oxide products are obtained. The fixed nitrogen processes, all of which yield high-grade manganese oxide products, are essentially either leaching or roasting processes. The 11 processes include HC1 leach, HC1 chloridization, HC1 chloride volatilization, CaC12 chloride volatilization, NO2 leach, HNO3 leach, HNO3 ?NO2 leach, H3 ?CO2-H2O system leach, (NH4)2SO4 leach, (NH4)2SO4 roast , and ammonium salt roast .

Jan 1, 1963

By Jr. East

The Bureau of Mines conducted an investigation of the Nightingale tungsten deposit about 38 miles north of Fernley, Nev., from September 1939 to March 1940, to determine possible resources of tungsten ore. The property was owned by the Gold, Silver & Tungsten, Inc., which maintained its offices in Boulder, Colo. Ore was discovered in 1917, and some ore was mined in 1918 and treated in a mill at Toulon, a station on the Southern Pacific Railroad, 40 miles east. Same shipments were made since 1918, but no production figures are available. The ore is mined from nearly vertical tactite bodies at the limestone-granite contact. The Bureau of Mines excavated 944 linear feet of trenches, drifted 52 linear feet, sunk a shaft 20 feet in depth, sampled the underground workings by cutting 743 linear feet of channels, sampled the surface trenches by cutting 415 linear feet of channels, and drilled 9 diamond-drill holes, totaling 3,000 feet. The ensuing sections note the location and physical features of the district and specify the property and ownership. The history of the mine is briefed, and the geology and mine workings are described. The work done by the Bureau of Mines is summarized and supplemented in detail by assay maps, logs of diamond-drill holes in appendix A, and a table of sample analyses in appendix B.

Jan 1, 1950

By Lindsay D. Norman

Four chloride and seven fixed-nitrogen processes for recovering manganese from domestic resources are described. The chloride processes are divided into two classes (leaching and chloridization) depending upon the major operation responsible for converting the manganese minerals to the chloride from which manganese oxide products are obtained. The fixed nitrogen processes, all of which yield high-grade manganese oxide products, are essentially either leaching or roasting processes. The 11 processes include HC1 leach, HC1 chloridization, HC1 chloride volatilization, CaC12 chloride volatilization, NO2 leach, HNO3-NO2 leach, NH3-CO2-H2O system leach, (NH4)2SO4 leach, (NH4)2SO4 roast, and ammonium salt roast.

Jan 1, 1963

By Almon F. Robertson

The floor of Shady Valley, Johnson County, Tenn., is underlain by the Shady dolomite formation. In places the residual clay derived from this formation contains considerable manganese oxides. Nine properties in Shady Valley and two in Doe Valley were prospected by the Bureau of Mines from January 1943 to April 1943. The results obtained indicate that the ore bodies are small and spotty and, that the ore is not well-adapted to gravity concentration. The work of the Bureau was confined to the open end of the valley. One mile northeast of the Ham Greer property, Beaverdam Creek enters a rocky gorge, and it was believed that the few prospects in this area were of secondary impor-tance and, owing to the steep slope and general roughness of the terrain, that exploration with the rite', bucket-drill would be impracticable. A total of 4,398.5 feet was drilled in 131 holes. In addition, 235 lineal feet of bulldozer trenches were cut and 4.5 feet of test pits were sunk. The following nine properties were explored in Shady Valley: Bentley, Walker, Blevins, Scott, North Ham Greer, South Ham Greer, Lipford, Blackburn, and Steagall In Doe Valley, the Gerd Shoun and Brookshire properties were explored.

Jan 1, 1949

By W. T. Benson

The nickel-bearing laterite deposits in the Pine Flat and Diamond Flat areas, Del Norte County, Calif., were investigated by the Bureau of Mines to determine the extent and nickel content of the two deposits and the amenability of the ores to metallurgical treatment. The work was based on drill-hole sampling and metallurgical tests in which attrition scrubbing and sizing, reduction roasting, and magnetic separation were used. Results of the sampling indicated that the deposits are comparatively small and are marginal or submarginal in grade. Metallurgical tests showed that no separation of cobalt from nickel and iron was made by sizing; however, a large portion of the chromium was separated. Reduction roasting and magnetic separation did result in upgrading the iron, nickel, and cobalt, and the simultaneous rejection of chromium.

Jan 1, 1963

By H. P. Hermance

The Ely mine, which at one time was the largest producer of copper in the United States, has been idle for the past 30 years. A remarkably continuous ore shoot probably averaging 100 feet wide and 19 feet thick was mined on about a 25° slope for 3,400 feet on the incline. The ore was massive sulfides containing chalcopyrite, pyrrhotite, pyrite, and sphalerite. The estimated production of the Ely mine is 400,000 tons of ore averaging 3.3 percent copper. Because of the critical position of copper during the recent war, a search for extensions and recurrences of parallel ore shoots at the Ely deposit seemed warranted. The Bureau of Mines surveyed selected areas by geophysical methods, diamond-drilled nine holes, and sampled mine dumps during its investigations, which began in 1942 and terminated in 1946. The diamond drilling totaled 5,229 feet. The logs of the holes include chemical analyses of mineralized sections.

Jan 1, 1949

By S. R. B. Cooke, F. D. DeVaney

"INTRODUCTION The potash mineral receiving the most attention in the newly discovered. New Mexico-Texas potash district near Carlsbad, N. M. is sylvite (potassium chloride). Sylvite contains more potassium than any other mineral. Merchantable high-grade deposits have been found, and those of lower grade may be enriched to a high degree of purity by refining methods. Deposits containing sylvite were the first to be developed and axe the only ones being mined.However, many other minerals that contain potash occur in the salt beds of the Carlsbad District. Of these the more important are polyhalite, carnallite, langbeinite, leonite, and kainite. The nature of the deposits and their mineralogy have been described in detail by members of the United States Geological Survey. 4/Langbeinite, although not so abundant in these deposits as carnallite and has particular interest because the potash is in the form of the sulphate and as such commands a premium in terms of K20 unit. This is explained by Fox and Turrentine 5/, who state:"

Feb 1, 1936

By J. W. Town

The Bureau of Mines conducted phosphate beneficiation studies to determine the influence of mineralogical and textural features on the recovery of phosphate from select bed and composite samples representing different phosphate rock types of the western Phosphoria Formation. Batch heavy-liquid tests showed that ore grade) pellet size, and type of interstitial material were significant parameters affecting concentrate grade and recovery. Recoveries at acid grade (31.5 percent P2O5) ranged from 98 to 56 percent. Liberation was essentially complete at 28 mesh, and recoveries tended to drop when overgrinding occurred.

Jan 1, 1966

By J. W. Griffith, J. L. Stauffer, L. M. Demers, D. C. Kuhn, S. Riliog

"The relative activation of eicosanoid production which results from the exposure of the alveolar macrophage (AM) to mineral dusts is thought to be a key factor in the pathophysiology of occupational lung disease. We compared in vitro basal and silicastimulated production of prostaglandin E2 (PGE2) and thromboxane A2 (TXA2) by AM from normal humans and non-human primates (Macaca nemistrina). In addition, we instilled mineral dusts directly into one lung of the non-human primate and evaluated AM eicosanoid production at two week intervals following dust instillation. Unstimulated AM from humans produce more PGE2 and TXA2 than do AM from M. nemistrina. However, in vitro exposure of AM from both species to silica dust produced a qualitatively similar increase in TXA2 production accompanied by no change in PGE2 production. Sequential analysis of AM eicosanoid production following a single bolus exposure to bituminous or anthracite coal dusts, titanium dioxide (Ti()i) dust or crystalline silica showed marked variability among individual non-human primates in qualitative and quantitative aspects of dust-induced eicosanoid production. However, the rank order of potency of the different dusts (silica> anthracite> bituminous) correlated with epidemiological evidence relating the type of dust mined to the incidence of pneumoconiosis. These studies suggest that the non-human primate may serve as a model for the study of both the role of eicosanoids in the etiology of dust-induced occupational lung disease and the biochemical basis for individual variability in the response of lung cells to mineral dust exposure. IntroductionOccupational inhalation of mineral dust can lead to chronic debilitating lung disease ( 1,2). One of the key components of the disease process is thought to be the interaction of mineral dust with the alveolar macrophage (AM) and the subsequent release by the AM of inflammatory and fibrotic substances (3,4). Chronic inhalation of mineral dust, depending on the type and amount of dust, may then produce a situation in which ongoing inflammation, accompanied by the destruction of functional lung tissue by products of activated AM and polymorphonuclear neutrophils, stimulates the production of nonfunctional matrix by lung fibroblasts.The AM produces several oxygenated derivatives of arachidonic acid (AA) which may play important roles in dust-induced lung pathophysiology (5,6). In previous studies in the rat, we found that prostaglandin E2 (PGE2). thromboxane A2 (TXA2) and leukotriene 84 (L TB4) were the major AA metabolites produced by AM (7). PGE2 is associated with pro-inflammatory activity (8) as well as anti-fibrotic activity since it downregulates interleukin -1 (IL-1) and tumor necrosis factor (TNF) release by AM (9-11). TXA2 is known to stimulate platelet activity, cause bronchial and vascular smooth muscle contraction (12) and to possess chemotactic activity (13). LTB4 is chemotactic for neutrophils and monocytes (14) and has been suggested as an additional regulatory factor in the release of TNF by AM exposed to silica dust ( 15)."

Nov 1, 1995

By L. B. Berger, W. P. Yant, J. B. Littlefield

"INTRODUCTION Hydrogen sulphide (H2S) is one of the most toxic industrial gases and of relatively wide occurrence in industry. Among its common industrial occurrences are, in the production and refining of high-sulphur petroleum, in natural gases, in gypsum and sulphur mining, in rock strata and underground waters (where it is encountered in tunneling and caisson work) in blasting with black powder and in blasting high-sulphide ores with other explosives, in gas manufacture, in the carbonization of coal, and in the manufacture of chemicals.The usual methods of detection, other than by the sense of smell, which is lost in 2 to 15 minutes' exposure to 0.010. to 0.015 percent of this gas, 5/ either are too cumbersome for frequent and rapid analyses or, like the wet lead acetate paper test, afford only qualitative results. A qaantitative determination usually involves the use of solutions, bubblers, flowmeters, standard solutions, burettes, and indicators manipulated by trained technical men. All apparatus and methods in common laboratory use are, in general, unsuitable for the field.The physiological response attending exposure to various Concentrations of hydrogen sulphide in air, is as follows, in percent by volume 6/:0.005 to 0.010: Subacute poisoning - slight symptoms, such as mild conjunctivitis and respiratory-tract irritation after 1-hour exposure."

Jun 1, 1935

By Russell. Paul L.

"INTRODUCTION Preliminary reports by Bureau of Mines engineers 3/ and by the Federal Geological Survey 4/ suggested that exploration would discover substantial reserves of minable ore in the Contact mine, Grant County, New Mexico. During February and March 1943, a sampling program was conducted on this property under the direction of the author. This was art of a general survey of the manganese districts of southwestern New Mexico.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources, to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as practicable soon as after its conclusion. The Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocer, chief, analyzes samples and performs beneficiation tests. Both these branches are under the supervision of Dr. S. Dean, assistant director. With respect to this report, special acknowledgment is due to C. H. Johnson, district engineer for New Mexico, and E. D. Gardner, regional engineer, and his staff, of the Central Region of the Bureau of Mines at the time of this work in 1943; also to Kenworthy, metallurgist at the Rolla. Mo., Laboratory of the Bureau of Mines, for work on beneficietion of the ore, and Sherman K. Neuschel, geologist of the Federal Geological Survey, for assistance in interpreting geological data at the project."

Oct 1, 1946

By R. G. Meara, O&apos

The land-pebble district of Florida, which in 1928 supplied 96.7 per cent of the phosphate production of that State and 82 per cent of the domestic requirements of the United States, is centered in Polk and Hillsboro Counties about 30 miles east of Tampa The deposits are unconsolidated sediments occurring as beds of phosphate matrix overlain by a mantle of barren sands and clays. The matrix consists of a mixture of Sand (quartz grains), clay, and phosphate rock in which the coarsest sand is much finer than the coarsest phosphate; that is, the sand is segregated in the fine material. Before the introduction of classifiers the concentration consisted of log washing, and screening at about 20-mesh, which was usually the finest size that could be taken to maintain commercial grade, 66 per cent B. P. L. (bone phosphate of limey or more. When classifiers were introduced some of the fines that had escaped at the head of the washery and some of the minus 20-mesh material isolated during the rushing and formerly lost supplied the feed.

Jan 1, 1931

By G. L. Gates

Five possible sources of water for waterflooding of petroleum reservoirs in the arid San Joaquin Valley of California were considered. Three of them (water produced with petroleum, water from a shallow saline aquifer, and waste irrigation water) were analyzed chemically; laboratory information for one (sea water) had been developed during a previous study. A series of laboratory tests made on the fifth source (fresh water) determined the solubility of calcium sulfate dihydrate in water. Laboratory analyses included the following: Chemical analyses of water produced with petroleum and waste irrigation water; solubility of calcium sulfate dihydrate in water and brines; the effect of excess sulfate on the solubility of calcium sulfate in brines; the presence of sulfate-reducing bacteria; and the permeability of cores from a petroleum reservoir to air, to water from other petroleum reservoirs, and to waste irrigation water. The results showed that most of the waters and mixtures of waters are compatible with petroleum reservoir waters and are generally suitable for injection. The calcium content of some of the formation waters is quite high, and care must be taken to prevent precipitation of calcium sulfate dihydrate. The permeability of the few cores tested was about the same to water and brines as to air, indicating that formation damage due to clay swelling will not be serious. The waters most likely to be available for injection are water produced with petroleum, water from shallow saline aquifers, and waste irrigation water.

Jan 1, 1970

By A. L. Peyton

The Brewer mine, near Jefferson, Chesterfield County, S. C., was originally operated as a gold mine. As late as 1890 this mine was reported to have been one of the large gold producers in the southeast. Occurrence of topaz on the Brewer property was not reported until 1935, when it was discovered, by Parks3/ and Parks of the Federal Geological Survey while they were investigating gold deposits in the Piedmont province.

Jan 1, 1953

By F. D. DeVaney

[In the course of the investigation by the U. S. Bureau of Mines and the Missouri School of Mines and Metallurgy at the Mississippi Valley experiment Station at Rolla, Mo., on the beneficiation of the low-grade manganese ores of the country, some samples from the Cuyuna District, Minn., have been examined. The work was done under the direction of W. H. Coghill, supervising engineer of the Mississippi Valley Experiment Station. Josoph and Kinney5 in venting about the relative importance of Minnesota deposits of low-grade ore compared to the total reserves say:]

Jan 1, 1930