Search Documents

By Kenneth J. Miner

Pittsburgh bed and Lower Freeport bed coals were tested in the U.S. Bureau of Mines two-stage froth flotation pilot plant, which utilizes a new flotation process to remove pyritic sulfur. The process consists of a first-stage coal flotation step to remove coarse, free pyrite and other refuse in the tailings. The clean coal froth concentrate is then repulped and treated with a coal depressant, a pyrite collector, and a frother to selectively float the remaining pyrite in a second stage. Results in the pilot plant were excellent, comparing well with those obtained in laboratory batch tests. That is, about 70 percent of the pyrite present in the Pittsburgh bed coal and about 90 percent of the pyrite present in the Lower Freeport bed coal were removed with excellent final clean coal recoveries.

Jan 1, 1973

By Joseph Cervik

Gas occurs in coalbeds in an adsorbed and a free gas state, Adsorbed gas is stored in the micropore structure and its transport is governed by Fick's law. The free gas occurs in the. fracture system and flows according to Darcy's law. These two modes of mass transport are interdependent. Production decline curves of coal-gas wells are of the constant percentage decline type and, thus, show no indications of flow characteristics peculiar to coal-gas reservoirs. The effectiveness of surface boreholes as a degasification scheme depends upon both good fracture permeability and a high fracture density. Conventional methods of reservoir engineering analysis are not applicable to coalbeds.

Jan 1, 1969

By A. J. Forney

This report summarizes the findings of methods of treating caking coals in a fluid bed to destroy their caking properties. In batch tests it was found that several coals, including those with a free-swelling index greater than 8, could be decaed at temperatures from 400° to 425° C with a fluidizing gas composed of inert gas or steam containing 0.2 percent oxygen and a minimum residence LS,-;,' of 5 minutes. When treatment decreased the free-swelling index from about 8 to 1-1/2 or lower, the resulting treated coal was noncaking. In a continuous unit with continuous feed and discharge of coal, slightly more severe conditions were required to decake the coal. For 18- to 100-mesh coal a temperature of 430° to 440° C and an oxygen-to coal ratio of 0.4 cubic foot of oxygen per pound of coal feed was necessary. Finer mesh sizes required lower oxygen-to-coal ratios. In tests using air only as the fluidizing medium and treatment temperatures well below the softening range, the caking properties of 150- to 200-mesh coal were destroyed in 30 to 40 minutes of residence time at 200° C. Coarser sizes of 18 to 48, 48 to 100, and 100 to 150 mesh required longer residence time.

Jan 1, 1966

By Wesley Holmes

Concentrating, nodulizing, and smelting studies were conducted at the Albany Metallurgy Research Center of the Bureau of Mines to determine whether (1) western iron ores of the type found in the Carter Greek deposit near Dillon, Mont., could be utilized; (2) concentrates of acceptable grade with good iron recovery could be attained by wet-magnetic beneficiation; (3) nodulized concentrates could be smelted with reductants readily available in Montana; (4) iron concentrates could be smelted without prior agglomeration; and (5) high-purity iron could be produced directly from high-grade concentrates, Three small samples and two tonnage samples from the Carter Creek deposit were uniform in chemical composition, and their iron content averaged about 31 percent. They were found to be banded gneisses, and magnetite was the principal iron-bearing mineral.

Jan 1, 1962

By Sidney Katell

This Bureau of Mines study estimates typical capital investments, operating costs, and selling prices for two bituminous coal strip mines in the Eastern and Interior provinces and a subbituminous coal operation in the Northern Great Plains province. The annual productions were based on tonnage required to fuel a 250-MM-scfd, high-Btu gas plant. The annual tonnage for the Eastern province mine is 4.8 million tons; for the Interior province mine, 6.72 mi 11 ion tons; and for the Northern Great Plains province mine, 9.2 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of May 12, 1974, under the terms of the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 and early 1974 indexes . Initial capital investment varies: $45,358,600 for the 4.8-million- ton-per-year (MM tpy) mine in the Eastern province, $54,603,000 for the 6.72 MM tpy mine in the Interior province, and $29,871,000 for the 9.2 MM tpy mine in the Northern Great Plains province. Total capital invest-ments for the Eastern province mine, the Interior province mine, and the Northern Great Plains province mine are $61,070,000, $76,753,000, and $56,286,000, respectively. Corresponding selling prices for the coal, per ton, are $4.79, $4.23, and $2.66, assuming a 12-percent discounted cash flow rate of return after Federal income taxes. These studies are considered typical for the areas involved. Costs will vary depending on specific locations in these areas.

Jan 1, 1974

By E. B. Kester

In the commercial evaluation of coal tars, a distillation analysis properly carried out is of considerable importance. Close attention must be given to this operation in order to obtain consistent results and to secure the minimum decomposition of the tar compounds, Which in Many cases are sensitive to undue heat effects. Low-temperature tars in particular contain compounds of this nature, while in the case of tars produced at high temperatures the large proportion of pitch present has an adverse influence during a distillation. If excessive cracking takes place, the composition of the distillate will naturally vary from the normal, with the result that all the analytical criteria subsequently obtained are affected. Where tars, produced over wide ranges of carbonization temperatures are investigated as in the survey of gas, coke, and by-product making properties of American coals now being conducted at the United States Bureau of Mines Pittsburgh Experiment Station, the method of distillation must necessarily be the same for all of the tars studied. Also, it mast function equally well for both low and high temperature tar permit accurate fractionation, and reduce adventitious decomposition to a minimum. The authors are aware that certain types of distillation analysis which do not meet the above requirements may give results comparable with those of the large stills of a by-product coke-plant where one type of tar is produced. These may be simpler and shorter and entirely suitable for control work, but at the same time have little value in a fundamental investigation.

Jan 1, 1932

By R. C. Hickman

Manganiferous breccia formations on three properties were prospected by the Bureau of Mines from January to November 1954 in Johnson County, Tenn. The prospecting consisted of diamond drilling, trenching, shaft sinking, and crosscutting. The results of the exploratory work show the manganiferous material to be low-grade, with little vertical extension. The manuscript on this report was completed February 1955. LOCATION The prospects are in Johnson County, Tenn. (fig. 1), within a radius of 12 miles from Mountain City. The nearest railroad terminal is Damascus, Va., 14 miles from Mountain City.

Jan 1, 1956

By Thomas M. Barczak

The safety of mine workers depends on the proper installation of roof supports to prevent the ground from collapsing into the working areas of an underground mine. As new support systems are developed, they need to be properly evaluated to make sure that they are capable of providing adequate roof support before they are first used in a mine. In addition to making certain that the supports meet basic safety criteria, the limitations of the support need to be fully defined in order to avoid improper application of a particular support design. The National Institute for Occupational Safety and Health (NIOSH) operates a world-class facility called the Safety Structures Testing Laboratory. This laboratory contains a unique load frame, the Mine Roof Simulator, which is capable of simulating the ground behavior in underground mines for conducting full-scale evaluations of roof support systems. Safety performance testing protocols using the unique Mine Roof Simulator have been developed for both standing roof support systems and longwall shield supports. The purpose of this paper is to describe these test procedures. The protocol for standing roof supports incorporates seven test series:( 1) uniform loading baseline tests, (2) height evaluations, (3) asymmetric loading, (4) biaxial loading, (5) load rate studies, (6) active loading determination, and (7) static loading evaluations. For longwall shields, a four-series test program that accurately simulates in-service conditions on a longwall face is proposed. This test program consists of (1) transfer of horizontal load to the caving shield-lemniscate assembly (zero-friction test),(2) point loading of shield joints due to lateral movement or rotation of the canopy, (3) evaluation of leg socketand leg cylinder integrity, and (4) face-to-waste racking of the shield. In addition, an evaluation of the shield’s hydraulic components will be conducted prior to the performance testing. These protocols will provide state-of-the-art safety performance evaluations of emerging support technologies, as well as a means to assess the safety of both new and aging longwall shields. Hence, this effort will enhance the safety of mine workers by ensuring that critical support elements are properly designed and that aging supports are retired before their support capability is jeopardized.

Jan 10, 2000

By E. B. Kester

In the commercial evaluation of coal tars, a distillation analysis properly carried out is of considerable importance. Close attention must be given to this operation in order to obtain consistent results and to secure the minimum decomposition of the tar compounds, which in many cases are sensitive to undue heat effects. Low-temperature tars in particular contain compounds of this nature, while in the case of tars produced at high temperatures the large proportion of pitch present has an adverse influence during a distillation. If excessive cracking takes place, the composition of the distillate will naturally vary from the normal, with the result that all the analytical criteria subsequently obtained are affected. Where tars, produced over vide ranges of carbonization temperatures are investigated as in the survey of gas, coke, and by-product making properties of American coals nor being conducted at the United States Bureau of Mines Pittsburgh Experiment Station, the method of distillation must necessarily be the sane for all of the tars studied. Also, it must function equally well for both low and high temperature tar, permit accurate fractionation, and reduce adventitious decomposition to a minimum.

Jan 1, 1932

By Herbert R. Babitzke

The purpose of this investigation was to optimize the high-temperature properties of columbium and tantalum. Columbium and tantalum were combined with selected alloying elements to achieve solid solution and dispersion strengthening. Fifty-six alloys were evaluated to determine their formability, hardness, strength at elevated temperatures, and oxidation resistance. The following six alloys showed high-temperature strength: [Cb-15Hf-5W-2Zr-4Al-4Ti-2N Cb-15Hf -5W-5Zr Cb-15.3Ti-4.1Zr-13.7Hf Ta-20Hf-4Al Ta-30Hf-4Al Ta-20Hf-5W-4Al] At 1,200° C, the columbium alloys had strength values of 40,000 psi or greater, and the tantalum alloys had strength values from 50,000 to 58,000 psi. For a 2-hour test period at 1,000° C, weight gains of only 9 and 8 mg/cm2, respectively, were observed on oxidation testing of two alloys, Cb-15Hf-5W-2Zr-4Al-4Ti-2N and Ta-20Hf-5W-4Al.

Jan 1, 1968

By Eric R. Bauer

This U.S. Bureau of Mines study was conducted to gain a basis for recommending methods to predict and prevent the occurrence of cutter roof failure, a common ground control problem in mines of the Northern Appalachian Coal Basin. This was accomplished by determining the geologic and engineering factors responsible for cutter development at six mines affected by cutter roof failure. Three distinct factors were found to be initiators of cutter roof failure: (1) high horizontal roof stress, (2) surface topographic variations, and (3) geologic anomalies. Effective control of cutter roof was obtained through improved bolting techniques, entry and mine reorientation, and entry and pillar size modifications, but only when selected based on the actual cause of failure.

Jan 1, 1990

By O. E. Traubert, E. G. Meiter

"The daily sulphur dioxide content of the air at the Pittsburgh Experiment Station of the Bureau of Mines was determined by the bureau at the request of Committee D-14 on Screen Wire Cloth of the American Society for Testing Materials. The purpose of the investigation was to obtain data for use in interpreting screen-corrosion tests, which were conducted simultaneously and jointly by the committee4 and the Bureau of Mines.The plan of this investigation was to vale a single daily determination, except on Sundays and holidays, of the SO2 content of the atmosphere at the exposed test screens, for a period of one year. No attempt was made to determine the variation during the day, except on the morning of October 15, 1927, when the atmosphere was unusually foggy and smoky. Several successive determinations were made on that date to ascertain changes in the SO2 as the morning haze disappeared. The SO2 determinations were begun on August 11, 1927, and continued until August 11, 1923.The Pittsburgh Experiment Station of the Bureau of Mines is in a residential section about 3 miles east of the central or main business district of Pittsburgh. The air samples were taken on the roof above the auditorium, or the center rear of the building. This was also the place where the pieces of screen were placed for corrosion tests. The height was about 40 feet above ground level. Several sources of considerable smoke and SO2 are in the immediate vicinity. On the west side of the building is a double-track railroad. At this point the line runs through a cat below the level of the building. The horizontal distance between the air-sampling position and the railroad tracks is about 400 feet, and the vertical distance about 70 feet. The power plant for the Bureau of Mines building is about 250 feet south of the sampling position. About 1000 feet farther to the south are the engineering building and power plant of Carnegie Institute of Technology, and 1/4 mile to the southwest is the power and heating plant for the Carnegie Library and Museum. About 1 to 2 miles farther south and also southwest"

Jun 1, 1930

By H. P. Greenwald

"INTRODUCTION In the course of its studies of the explosibility of various coal dusts in the Experimental coal mine, the Bureau of Mines has tested coals representing the entire range of volatile content found in the United States. In connection with their work the Bureau's field engineers some¬times meet operating officials who are not impressed by the fact that there is an explosion hazard in mines working low—volatile coals. Actually the difference in explosion hazard between high—volatile and low—volatile coals is one of degree and not of kind. The purpose of this paper is to set forth briefly the experimental evidence that has been accumulated on the explosibility of coal dusts containing 8 to 31 percent volatile matter on a dry, mineral—matter—free basis.There have been numerous dust explosions in mines in which coals were worked that have compositions within this range. Those explosions are listed in an appendix, together with a bibliography of Bureau of Mines papers describing explosion tests in the Experimental coal mine."

Jan 1, 1940

By L. A. Haas

Hydrogen sulfide was decomposed to elemental sulfur in an electrical discharge. With He, N., or Ar diluents, a threshold voltage between 1 and 3 kV was required for the decomposition reaction to occur in a laboratory ozonizer. Above the threshold voltage, the HAS decomposition rate increased with increasing voltage, but the increase was more pronounced with argon diluent than with either nitrogen or helium. In common with other reactions in an electrical discharge, the B2S decomposition decreased with increasing temperature in the range of -410 to +61° C. The reaction did not appear to be rate-controlled by a solid-gas sorption step because the introduction of activated charcoal into the electrical discharge zone did not significantly affect the decomposition yield. In the presence of polymeric chlorofluoro-carbon oil, 90 pct conversion of the 3 pct H2S in helium was obtained at 14 kV, 60 Hz, a 2-mm electrode gap, and a gas-residence time greater than 1 min. Under the same experimental conditions in the absence of oil, the conversion was only about 50 pct.

Jan 1, 1973

By John A. Organiscak

[Fugitive Just is generated alone unpaved mire reads from intermittent equipment traffic. Typically, the majority of such traffic consists of trucks hauling either mine product or waste [rum the surface mime pit and/or the processing plant. Fugitive dust generated along these unpaved mine roads includes particles of all sizes which become airborne. The potential hazards include the deleterious effects to human health of inhaled dust, traffic visibility hazards and environmental impacts on the localized area by the larger-sized visible airborne dust. Two held surveys were recently conducted to quantify fugitive dust generation and dispersion from truck traffic on unpaved and untreated mine haulage roads For these surveys., airborne glow sampling was conducted at multiple sampling fixations away from an unpaved haulage road at a limestone quarry/plant and at a coal mine preparation plant lo measure the size characteristics, concentrations. and dispersive behavior of the dust cloud generated from truck traffic- Results show that at least 80% of the airborne Just generated by haul trucks was larger than 10 µm- Airborne respirable, thoracic, and total dust concentrations all decreased and approached background concentrations 30.5 in (100 feet) from the road This report describes the average and instantaneous peak dust levels that were measured tip to 30.5m (100 feet) Iron the haulage road. Keywords: Unpaved mine road, fugitive dust, silica.]

Jan 1, 2008

By N. S. Dalal, X. Shi

"Electron spin resonance (ESR) measurements provide evidence for the formation of Cr(V) intermediates in the enzymatic reduction of Cr(VI) by glutathione reductase (GSSG-R) in the presence of NADPH, indicating an initial single-electron transfer step in the reduction mechanism. Depending on the pH, at least two different Cr(V) species are generated which are relatively long-lived. In addition, we have detected the hydroxyl (·OH) radical formation during the GSSG-R catalyzed reduction of Cr(VI) by spin trapping, employing 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) and a-(4-pyridyl-1-oxide)-N-tert-butylnitrone (4-POBN) as spin traps. Superoxide dismutase (SOD) causes only a minor effect on the ·OH radical and Cr(V) formation, indicating that the ~ - is not significantly involved in the reaction mechanism. Catalase enhances the Cr(V) formation and substantially inhibits the ·OH radical formation, indicating the involvement of hydrogen peroxide (H20 2) in the reaction mechanism. Addition of H20i suppresses Cr(V) and enhances the ·OH radical fonnation. Measurements involving N-ethylmaleimide show that the Cr(V) species, produced enzymatically by the reduction of Cr(VI) by GSSG-R, react with H2O2 to generate ·OH radicals, which might participate in the initiation of Cr(VI) carcinogenicity.INTRODUCTIONC(VI) compounds have been found to exert serious toxic and carcinogenic effects on humans and animals [1-4) and to cause mutations in bacteria and transformation of mammalian cells [5-8). In contrast, most Cr(lll) compounds are relatively nontoxic, noncarcinogenic, and nonmutagenic [9, 10]. Cr(VI) and Cr(lll) oxidation states are different in their metabolic pathways: Cr(VI) ions are rapidly transported across cellular membranes [2, 11-13), while Cr(lll) moieties do not easily penetrate cells and are not oxidized by cellular constituents [3]. Since it is known that the reduction of Cr(Vl) is required for its reaction with DNA [2], the molecular mechanisms for the intracellular Cr(VI) reduction have been the focus of studies during the past decade but the details are still not understood."

Jan 1, 1990

By W. H. Oppelt

To provide a relatively structurally stable form of dried lump lignite, two North Dakota lignites from Mercer County were dried by the Fleissner process in an atmosphere of saturated steam at 200, 300, and 370 p.s.i.a. pressure, corresponding to steam temperatures of 382°, 417°, and 437° F., respectively. Two series of experiments were made at each test pressure with the individual lignites. In one series, the autoclave was preheated to the processing temperature before charging the lignite; in the other the lignite was charged into the autoclave at room temperature. In each case, heat losses were determined by blank tests of steam consumption over a similar operating cycle with the empty autoclave. The degree of moisture removal and net steam consumption were calculated from material balances. The amount of water removed as a liquid from the two North Dakota lignites during the heating and steaming periods was compared with results calculated from previously published data on drying Austrian lignite and Australian brown coal. These lignites, covering a wide geographical area, had original moisture contents ranging from 35 to 49 percent. The Austrian lignite and Australian brown coal are considered to be of Miocene Age, and the Dakota lignites belong to the Paleocene.

Jan 1, 1955

By Stephen P. Holt, John A. Bowsher

A preliminary examination of the mica deposits in Culberson and Hudspeth Counties , Texas , was made in September 1942 by A. B. Needham, district engineer of the Bureau of Mines . The deposits were reexamined by R. C. Redfield , associate mining engineer of the Bureau in November 1942, at which time he was accompanied by Philip S. Hoyt , geologist , and J. C. Moore , foreman of the Texas Mica and Feldspar Company . Exploratory work was started on February 16 , 1944 , and terminated on April 30 , 1944. A crew of 4 to 10 men was employed under the supervision of the authors .

Feb 1, 1947

By E. L. Garton

The United States Bureau of Mines has recently collected samples of crude petroleum from wells in the newly developed Joiner. Kilgore, and Longview fields of Rusk and Gregg Counties in the East Texas district, and from the Van field of the East Central district of Texas.

Jan 1, 1931

By E. L. Garton

The United Status Bureau of Mines has recently collected samples of crude petroleum from well] in the newly developed Joiner, Kilgore, and Longview fields of Rusk and Gregg Counties in the East Texas district, and from the Van field of the East Central district of Texas. East Texas Cruder The four samples of crude oil from the East Texas fields are all typical "intermediate base" crudes according to the classification given by Smith and Lane. 3 Sample 31,063 is from the discovery well in the Joiner field. This well came in on October 3, 1930, with an initial production of 400 barrels per day. Sample 31,062 was obtained from a well that was completed on February 1, 1931, with an initial production of 3,500 barrels per day. The 32 East Texas crudes are produced at an average depth of approximately 3,600 feet. which is the deepest Woodgine-sand production so far encountered in any of the Texas or Louisiana fields.

Jan 1, 1931