Search Documents

By A. W. Deurbrouck

Four samples of Pittsburgh-bed coal, of various size consist and ash content were dewatered in a pilot-size vacuum-disk filter partially enclosed with a steam jacket. Steam fed at 2.5 to 12.5 pounds per minute reduced the moisture content of the filter cakes from 2.8 to 13.8 percentage points more than normal vacuum dewatering. Approximately 1.5 pounds of steam was required to remove 1 pound of water.

Jan 1, 1966

By P. J. Colbassani

Samples of mine atmospheres collected by Federal coal-mine inspectors during their inspections and investigations of coal mines, in accordance with provisions of the Federal Coal Mine Safety Act (66 Stat. 692; 30 U. S. C., sees. 451-483) are analyzed routinely by chemical methods at Bureau of Mines laboratories. When samples collected in open workings of nongassy coal mines at points not less than 12 inches from the roof, face, or rib contain 0.25 percent or more methane, the act requires the operator, during operation of such mine, to comply with the provisions of sec. 209, Title II, of the act, which pertain to gassy mines. The methane con-tents of such samples are determined by a physical method based on infrared absorption spectrometry to provide an independent check on analytical results obtained by chemical methods. This information circular describes the equipment and procedures used by the Bureau for determining low concentrations of methane in coal mine atmospheres by infrared absorption spectrometry. ACKNOWLEDGMENTS The authors are indebted to Dr. R. A. Friedel, Chief of Spectrometric Section, Branch of Coal-to-Oil Research, Bureau of Mines, for suggesting the analytical method and for furnishing valuable advice and assistance, and to J. A. Queiser of his staff for making exploratory measurements by this method; to Dr. M. G. Zabetakis of the Division of Explosives Technology for his assistance during the conduct of preliminary experimentation; and to L. B. Berger, Chief, Branch of Health Research, under whose guidance the equipment was procured and the work conducted.

Jan 1, 1958

By J. J. Drost

The feasibility of basic oxygen furnace (BOF) offgas heat recuperation by preheating scrap was investigated on a pilot plant scale by the Bureau of Mines. In this study, offgases generated during the oxygen blowing of a molten pig iron and scrap charge were passed through a static bed of shredded auto scrap. Scrap quantities varying from 100 to 180 pounds and representing from 22 to 40 percent of the 450-pound BOF metallic charge were preheated in this manner. Average scrap bed temperatures of 1,650° F for 100 pounds of scrap and 1,150° F for 180 pounds of scrap have been achieved during the blows. As compared to cold scrap used in the normal BOF practice, it was found that by preheating scrap, usage could be increased by 43 percent. The thermal energy recovered by this preheating method can account for up to 44 percent of the energy necessary to melt the scrap.

Jan 1, 1974

By R. E. Lindstrom

A study of ion-exchange resin crosslinkage and eluant flow rate, resin-bed shape, and addition of separating ions to feed stock was undertaken to determine their effect on the separation efficiency of ion-exchange on bastna-site-rare-earth elements. Results show that 12-percent divinylbenzene (DVB) crosslinkage resin is detrimental to separation efficiency at flow rates over 2 to 5 ml./min./sq. cm.; whereas, separation with 4-percent DVB crosslinkage resin is relatively unaffected by flow rates between 2 and 10 m1./min./sq.cm.

Jan 1, 1959

By M. H. Kline

The Chestatee mine is one of several well known pyrite deposits in Georgia that are reputed to carry appreciable quantities of copper with the ore. The deposit is? in Lumpkin County on the Chestatee River, 6 miles northeast of Dahlonega (fig. 1). Old records and reports indicated the probable existence of an extensive unmined ore body, but the mine is inaccessible at present. The Bureau of Mines, after studying old maps and records, decided to cor8-drill along the strike of the lense beyond the limits of the indicated old workings in an attempt to extend the possible reserves. The advantageous location of the property indicates that it could become an economic source of pyrite to be used for the manufacture of sulfuric acid. Iron sinter resulting from the roasting of the ores could be sold at a premium in the Birmingham, Ala., area, and the copper content could be extracted to help replace the nation's depleted resources of this metal.

Jan 1, 1949

By Jennifer Riefenberg

The U.S. Bureau of Mines has long recognized the hazards associated with rock burst activity in underground mines. Concern over lost lives and resources prompted this study to further characterize rock burst occurrence as related to microseismicity and mining. A period of over 1,079 days of mining with 101 bursts, where microseismicity rates and blasting were recorded, was used in this study. Statistical analyses investigated relationships between (1) rock burst occurrence versus blasting, (2) rock burst size versus damage, (3) rock burst occurrence versus average micro seismicity rates, and (4) rock burst occurrence versus local mine geometry. Statistical analyses showed that 91% of all rock bursts occur with blasting while only 3% of all rock bursts occur, apparently, independent of blasting. Additionally, the long-term average daily micro seismicity rates appear to dictate when blasting will trigger rock bursts. Time series analysis on the daily microseismicity resulted in model equations that may be used to forecast the daily microseismic activity.

Jan 1, 2010

By Peter N. Gabby

In 1990, the Bureau of Mines conducted a mineral resource investigation of the 12.321 acre Black Warrior study area, one of several proposed additions to the Sawtooth Wilderness. No identified mineral resources were delineated. There were 123 lode and placer claims in or adjacent to the study area. There is a known hot spring adjacent to the study area, but presently no geothermal leases are pending. Lode mines in pr adjacent to the Black Warrior study area have produced 4,022 tons of ore from which 1,981 oz of gold and 811 oz of silver were recovered. None of the vines are currently active. During the field study 125 rock samples were taken. Significant gold assays and favorable geologic characteristics at seven properties indicate that gold occurrences and resources with byproduct metals may exist in the study area. Two other sites yielded anomalous gold assays; however, sage favorable geologic characteristics are lacking. Presently, identified gold resources are being delineated by drilling programs in the nearby Atlanta and Rocky Bar mining districts. These districts have geologic characteristics similar to the Black Warrior area. During the field study 22 placer samples were taken. In most places where an anomalous concentration of gold was found, the stream channels are too narrow for operations other than recreational suction dredges. However. One area is estimated to contain over 2 million yd3 of gold-bearing gravels.

Jan 1, 1992

By James R. Coldwell

Mining and processing cost analyses were conducted by the U.S. Bureau of Mines on massive sulfide copper-zinc and low sulfide vein gold deposit types that may be found in the Ketchikan Mining District. Reserves and recoverable metal values (RMV) needed to make these deposits economically viable were modeled. Methods for estimating ore grades and required RMV are presented. Economic modeling for massive sulfide deposits indicated the RMV necessary for a 15% Discounted Cash-Flow Rate-Of-Return (DCFROR) for an underground cut-and-fill mine ranged from $137/mt for a 6,100 mtpd on-site milling operation to $526/mt for a 450 mtpd off-site milling operation. On-site milling was always less costly than off-site milling. Economic modeling for low sulfide vein gold deposits indicated the RMV necessary for a 15% DCFROR for an open-pit mine, off-site mining operation ranged from $S4/mt at 2,900 mtpd to $71/mt at 360 mtpd, and from $49/mt at 2,900 mtpd to $100/mt at 360 mtpd for an on-site milling operation. Off-site milling was less costly than on-site milling until production exceeded approximately 1,700 mtpd. Then, economies of scale reduced operating costs enough to offset the higher capital costs required for on-site milling.

Jan 1, 1995

By James A. Browning

Following an unsuccessful attempt earlier in the program to develop and market a drill channelling machine, we have designed and tested a new continuous channelling method which reduces operating sound levels to below 100 db. This new method relies on a small diameter oxygen-enriched burner to produce narrow channels. Sound intensities are reduced substantially compared to conventional channel widths. They are further reduced by a water spray directed immediately above the flame. Baffles placed along the top of the channel will reduce sound levels to below 90 db. Cutting rates are greater than those of existing channelling burners with costs per unit of channel area substantially reduced for those cases where oxygen costs are reasonable.

Jan 1, 1981

By Joseph Cervik

This Bureau of Mines report deals with water infusion of coalbeds, which can control methane emission at face areas during developmental mining and which may sometimes suppress dust. Studies show that water infused into the coalbed flows through the fracture system and displaces the methane in the fractures and prevents migration from the solid coal. Displaced gas migrates away from the face area that has been water infused and enters the return ventilation airways. A gradual decrease in methane emission is observed from the start of infusion until the infused zone is mined through. Depending on the permeability of the coalbed, infusion pressures ranged from 300 to 2,200 lb/in2. Face emissions in the Upper Kittanning coalbed were reduced by 89 pet; reductions of 38 to 79 pet were measured in the Pittsburgh coalbed depending on the relationship between the face cleat direction and mining direction. Respirable dust levels were reduced by about 75 pct on a longwall section in the Pocahontas No.3 coalbed and by about 50 pct on a development section in the Upper Kittanning coalbed, but no statistically reliable reduction was found in the respirable dust levels in the Pittsburgh coalbed.

Jan 1, 1977

By W. J. Fullerton

This paper is one of a series prepared for the United States Bureau of Mines discussing the methods used in crushing and grinding materials for cement manufacture, and deal particularly with the methods used at the Howes Cave plant of the North American Cement Corporation. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that publication of total production costs might in many instances cause embarrassment to individual producers as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue.

Jan 1, 1932

By Charles H. Atkinson

The Rio Blanco massive hydraulic fracturing demonstration has been undertaken by the Bureau of Mines, Atomic Energy Commission, and a group of 15 industry participants. CER Geonuclear Corp. has been retained as program manager to evaluate the stimulation effects of very long fractures, suitably propped open in thick sections containing multiple intervals of low-permeability gas-bearing sands. The zone of interest for this demonstration includes Fort Union and Mesaverde sands from about 5,800 to 8,.200 feet deep in Rio Blanco County, Colo., about 1 mile from the site of the May 1973 triple nuclear detonation aimed at stimulating production from the same reservoirs. Drilling the test well and evaluating the reservoir prior to fracturing was funded by Government participants; fracturing and production testing will be funded by industry. The test well has row been completed at a total depth of 8,170 feet, and data obtained from logs, cores, production and drill-stem tests indicate reservoir conditions to be less favorable for gas production than anticipated. Structural position is lower than expected, resulting in higher water saturation than was determined for the same sands at the nuclear fracturing location. The lower sands of the Fort Union sequence appear to have higher shale content than has been encountered in other wells in the area. Despite the likelihood that gas productivity will be undesirably low following stimulation, the industry participants decided to proceed with the stimulation program with the thought that the resulting data would be useful. The success of the stimulation test probably will have to be judged by production increase rather than by production volume.

Jan 1, 1975

By S. J. Page, P. Bolsaitls, W. E. Wallace, C. A. Hill, M. J. Keane

"Boiling respirable quartz dust in water for 10 to 40 minutes decreases the cytotoxicity for both erythrocyte hemolytic potential and pulmonary macrophage release of lactate dehydrogenase in vitro. The potential is reduced to near zero in the boiling concentration range of 1 to 10 mg quartz per ml water in boiling times of 20 to 40 minutes. Below this range the detoxification occurs over a longer boiling time. Above this range the hemolytic potential remaining after 40 minutes of boiling approaches native quartz potential with increasing concentration up to 30 mg quartz per ml water. Replacing the media with fresh at the midpoint of boiling results in full detoxification through 20 mg per ml. Pre—boiling the medium with quartz or silica gel reduces the effect of subsequently boiling test samples. Detoxification persists after mild drying at 110 C for 8 hours, and persists after three days of resuspension in water at room temperature. Additional data on persistence of the effect, on the use of acidic and basic media treatment, and on surface analyses are presented, with a discussion of a working hypothesis and research needs.IntroductionResearch underway to determine interactions of quarts and other mineral dust surfaces with pulmonary fluids and alveolar macrophages in culture led to the observation that when dusts were autoclaved in aqueous suspension, their cytotoxic effects on macrophages wore suppressed, in some cases fully and even after several days incubation with the cells. This finding was in direct contradiction to earlier results from both short term macrophage lysosaal enzyme release assays, as well as longer term cytotoxicity assays from macrophages in culture; in those studies, dusts were steam autoclaved at 121 121 ºC with no liquid water but with steam present. (1,2) However detoxification under boiling conditions has been reported in other research.(3). It was decided to use the hemolysis assay to further investigate these findings, because of its sensitivity, simplicity and cost."

Jan 1, 1988

By James P. Bennett

The Bureau of Mines investigated the effect of refractory oxide additions, introduced in soluble form, on the high-temperature properties of 90- and 98-pct-MgO brick. Brick samples were soaked in solutions containing Al, Ca, Cr, Co, Fe, Mg, Mn, Mo, Ni, Si, Sr, Sn, Ti, or Zr ions. Additions to 98-pct-MgO brick did not generally result in statistically significant property improvements. Statistically significant improvements were noted in hot modulus of rupture (MOR), slag resistance, and spalling resistance of the 90-pct-MgO brick for additions of Al, Mg, or Sn. High-temperature performance of treated 90-pct-MgO refractories was equal to or approached that of 98-pct-MgO brick. The marked improvements due to tin were obtained with additions of only 1.14 wt pct Sn02.

Jan 1, 1985

By Richard L. Rains

In 1984 and 1985, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied part of the 162,887-acre Mormon Mountains Wilderness Study Area (NV-050-161) in order to evaluate its identified mineral resources. The study area is located in Lincoln County, NV, about 60 miles northeast of Las Vegas. The study area had no mines or mining claims in 1985, and no mineral resources were identified within the study area, or at the Whitmore mine or Iron Blossom prospect near the study area. The alluvial fans around the southern boundary are staked with about 450 placer claims. Chemical analyses of samples indicate that some limestone in the study area is suitable for manufacturing cement or for agricultural purposes but the limestone is distant from markets and therefore not economic in the foreseeable future. The study area is blanketed with oil and gas leases, but no known productive horizons were identified.

Jan 1, 1986

By Donald E. Graham

A mineral survey of a 12,350-acre portion of the 13,150-acre Juniper Creek Wilderness Study Area (WSA) in southwestern Idaho was conducted by the U.S. Bureau of Mines in 1984. The area is entirely underlain by thick flows of Banbury Basalt. Rhyolitic tuff of Little Jacks Creek is exposed in the walls of the Owyhee River canyon beneath the basalt. Minor units of lacustrine sediment occur between the volcanic layers. No mines or claims occur in the area, and no mineralized zones were found. The study area is covered by oil and gas leases or lease applications; there has been no known exploration.

Jan 1, 1985

By Fredrick L. Johnson

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 25,640 acres of the 29,680-acre Devil?s Garden Lava Bed, 21,040 acres of the 28,660-acre Squaw Ridge Lava Bed, and 9,100 acres of the 12,600-acre Four Craters Lava Bed Wilderness Study Areas (OR-D01-D02, OR-001-003, and OR-001-022, respectively) in order to evaluate their identified mineral resources. The study areas are located in Lake County, OR, about 50 air miles southeast of Bend. No mineral resources were identified in the three study areas. The areas are almost entirely underlain by recent lava flows. Cinder cones occur in each of the areas; however, the best cinder occurrences are in the Four Craters Lava Bed study area. Slab lava, of facing stone quality, is scattered throughout the Devil?s Garden Lava Bed study area, and to a lesser extent, in the Squaw Ridge Lava Bed study area.

Jan 1, 1987

By R. L. Grant

Study of the ignition of firedamp by explosives and the phenomena that underlie it is one of the long-term investigations of the Bureau of Mines. This report is the third in e series by the Explosives Branch summarizing the progress made at Bruceton in this study. The first paper described preliminary work on small, carefully controlled cannon shots the second discussed the results of suspended shots.5/ In this paper, experiments are described and interpreted that extend and support the concept of ignition presented previously. ACKNOWLEDGMENT The authors wish to thank Bernard Lewis, former chief, Explosives and Physical Sciences Division, and Guenther von Elbe, former chief, Physical Sciences Branch, Explosives and Physical Sciences Division, for their guidance and constructive interest.

Jan 1, 1954

By A. C. Johnson

The Ellington manganese deposit in Reynolds County J Mo., had been known for some time; and limited exploration, consisting of test pitting and sinking a shaft 54 feet deep on the property, had been done by private interests. Late in 1941, the Bureau of Mines cleaned, deepened, and sampled many of the existing pits and dug and sampled 27 new ones. The shaft was unwatered and sampled, and several pockets of manganese ore were trenched to determine their extent. Samples were analyzed and beneficiation tests on 1 ton of the ore were made at the Rolla, Mo., station of the Bureau of 'Mines. Results of the investigation indicated that the deposit was small and low in manganese content.

Jan 1, 1948

1. In 2001, a total of 785 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). Examples of nonmetal mining operations include the mining of clay, trona, barite, phosphate rock, gypsum, talc, gemstones, and pumice. Nonmetal mines comprised 5.4% of all mining operations.1 • Nonmetal mining operations are located in all but seven states or territories (Alaska, Delaware, Maine, New Hampshire, Rhode Island, Puerto Rico, and the Virgin Islands). • The median number of operator employees per nonmetal mine was 6.1.2 • Mines producing common clay comprised 31.2% (n = 245) of all nonmetal mining operations.

Jul 1, 2003