Search Documents

By A. J. Barry

Two methods of testing anchorages of headed expansion-type mine roof bolts were investigated by the Federal Bureau of Mines to determine whether they are acceptable for general use. In both methods a load was applied to a tightened bolt with a hydraulic jack. A total of 80 tests, 40 using each method, was conducted in 4 test areas in 3 commercial coal mines. Electric resistance strain gages were used in all tests to indicate true bolt load as the bolt was tightened and when an additional load was applied with the hydraulic jack. The results indicate that: 1. The relationship between the true bolt load and the jack load will vary according to the test method until the two loads become equal. The bolt load-jack load relationship below this point can be determined only with strain gages. 2. The point at which the two loads become equal can be estimated by noting the load when the hardened washer becomes loose in one method, and when the bearing plate becomes loose from the roof in the other. It also can be approximated for either method of testing by noting the load when the first abrupt change in the slope of the jack load-bolt displacement curve occurs. 3. The anchorage characteristics of the test bolt can be determined from the data obtained from either method by examining the slope of the jack load-bolt displacement curve above the point at which the true bolt load is equal to the jack load.

Jan 1, 1960

By L. C. IlsLey

One of the details which the engineers observe closely in conducting tests on explosion-proof type equipment at the Pittsburgh experiment Station of the Bureau of Mines is the construction of covers and their means of fastening. These covers are of particular concern from a safety standpoint, because they are very liable to be frequently disturbed for the purpose of making inspection or repairs to internal parts of motors, controllers, etc. When depended upon to permit frequent inspections it is desirable from a practical operating standpoint that the cover be easily and quickly removed and replaced. The position that been taken by the Bureau of Mines is that the questio of ease with which covers will permit inspection should be determined by the mamu- facturer and the user. If the scheme used requires considerable effort, as in the removal of several bolts, it has been assumed that the one going to all this trouble to get the covers off could be trusted to put the cover back in place properly, especially as the approval plate generally calls specific attention to this point. Where a cover is simply screwed in place, fastened by a single bolt, or secured by a hing in or other similar arrangement, the bureau has not been willing to assume that the, cover would in all cases be properly fastened and has required further security by means of a lock or seal. In the course of its investigations the bureau has had occasion to inspect and test five types of covers as follows: (1) Covers having two plane surfaces bolted together. (2) Covers having two plane surfaces held together by lugs, clamps, or other means besides bolts. (3) Covers which have screw thread and fit a similar thread in the compartment. (4). Covers having plane surfaces with the addition of a tongue-and-groove joint at about the center of the plane surface and in general secured by hinge pins or similar means of fastening. (5) Covers in the form of an annular ring accurately fitted to a motor shell which can be rotated around the shell, and thus make easy access to inspection openings in the shell and rotated back again to effectively seal these openings. Tests. have also been made of large bolted covers having a smaller and more accessible cover within the large one, which could be opened for inspection purposes.

May 1, 1930

By Jürgen F. Brune, William H. Schiffbauer

Communication problems are not new. Research in this area goes back as far as 7922 when the US Bureau of Mines performed experiments to detect radio signals from inside their experimental mine in Bruceton, Pennsylvania. Many improvements to mine communications have been made over the years but for any number of reasons the underground coal mining industry has been behind in implementing advances. Present communications systems far underground mines can be hard-wired or wireless. Both types of systems can fail when faced with fires, roof falls, explosions, and power or battery failure. Currently installed wireless communications systems usually employ a special antenna cable called a "leaky feeder" Fiber optic cables are also used in some applications to form a "backbone" for wireless transceivers. Through-the-earth (TTE) and wireless radio systems are less common. Except for TTE systems, most wireless systems require some wire-bound components, which are susceptible to failure during disasters as cable breakage interrupts communications.

By Harold W. Lipper

Helium production and shipment reached new peaks in 1.361. The Bureau of Mines produced 727 million cubic feet, 13 percent more than the 1960 record, and shipped 552 million cubic feet, 16 percent more than the 1960 record. Production exceeded demand for the third successive year, enabling the Bureau of Mines to add 174 million cubic feet to the volume stored underground for future use. At the end of 1961, the total volume of helium in underground storage in the Clifside gasfield was 44-7 million cubic feet. Contracts to implement a long-range helium conservation program were completed with four companies, obligating all the contracting authority of $47.5 million a year made available by the Congress. The four companies will finance, build, and operate helium extraction plants to recover from natural gas an annual average of 3.1 billion cubic feet of helium that would ordinarily be wasted when the helium-bearing natural gas is used for fuel.

Jan 1, 1962

By J. Nielen van der Merwe

The move toward partial pillar extraction versus full pillar extraction has necessitated a new approach to underground section stability. When pillars are mined too small to support the weight of the overburden, they will, in some cases, remain stable for a considerable period; in other cases, they will collapse unexpectedly and violently. There is no discernable difference between the pillar safety factors of the failed and stable cases. The explanation lies in the characteristics of the overburden layers. A method is proposed that recognizes the overburden characteristics in the evaluation of stability. Two stability factors are calculated: one for the pillars, the other for the overburden. Using this method, it is possible to make use of the bridging capabilities of overburden layers to prevent pillar collapse. It is possible to scientifically design partial pillar extraction layouts that will be safe. Using energy considerations, it is also possible to prevent violent failure of pillars.

Jan 5, 1999

By Jeffrey Kohler, John J. Samrnarco, Thomas Novak, Lloyd Morley

Equipment control functions that were once hardwired are being implemented with software and very large scale integrated (VLSI) devices. Often this transition has resulted in increased flexibility, improved quality, and decreased costs. At the same time, it has created new concerns and challenges concerning worker safety. The visible and well-defined ladder diagram for relay-logic has been replaced by program in which the exact outcome for varied inputs can be more obscure. In the coal mining industry,-efforts to automate longwall mining systems hove resulted in semiautonomous machines operating within the same space as workers This paper describes an effort initiated by the National Institute for Occupational Safety and Health (NIOSH to identify the safety rules related to the use of processor-controlled equipment in mining. Specific findings in the areas of human factors, hardware, and some safety are presented in this paper, and a brief description of a plan to address identified weaknesses is given.

By Carlton E. Brown, William P. Yant

"INTRODUCTION Direct visual microscopic determination of particle-size distribution and number concentration of atmospheric dust is time-consuming and trying to the eyes. By using the microscope to project images of the particles at high magnification onto a screen much of the eyestrain can be eliminated and particle-size distribution results obtained with less effort and at a considerable saving in time. It also permits simultaneous observation of the images by more than one person. Microprojection requires no more skill and very little more apparatus than is required in the use of the microscope. Anyone familiar with the microscope should be able to obtain as perfect images on the projection screen as in direct visual microscopy since the same laws and limitationsThe theory and practice of microprojection are described in detail in texts. 5/6/ The procedure has been used and found to be satisfactory for measuring the particle-size distribution of sub-sieve-size substances, such as pigments and powder 7/8/ in the same size range as that of atmospheric dust. The Bureau of Mines has used the microprojector and found it to be quite satisfactory for (1) the determination of the number concentration of atmospheric dust R.I. 3289 in samples collected by the Owens jet dust counter; (2) particle-size distribution in samples of atmospheric dust collected by the Owens jet dust counter and by the electric precipitator; and (3) the particle-size distribution of dusts, blood cells, bacteria, and pollen. Work is in progress at this Bureau on the use of the microprojector in counting impinger samples. The use of different kinds of illumination, such as reflected (dark field), polarized, monochromatic, and ultraviolet, in the projection of images of atmospheric dust particles is being considered."

Oct 1, 1935

By John J. Sammarco, Edward F. Fries

This report (Independent Functional Safety Assessment 4.0) is the fifth in a nine-part series of recommendations addressing the functional safety of processor-controlled mining equipment. It is part of a risk-based system safety process encompassing hardware, software, humans, and the operating environment for the equipment’s life cycle. Figure 1 shows a safety framework containing these recommendations. The reports in this series address the various life cycle stages of inception, design, approval and certification, commissioning, operation, maintenance, and decommissioning. These recommendations were developed as a joint project between the National Institute for Occupational Safety and Health and the Mine Safety and Health Administration. They are intended for use by mining companies, original equipment manufacturers, and aftermarket suppliers to these mining companies. Users of these reports are expected to consider the set in total during the design cycle. • 1.0 Safety Introduction.—This is an introductory report for the general mining industry. It provides basic system/software safety concepts, discusses the need for mining to address the functional safety of programmable electronics (PE), and includes the benefits of implementing system/software safety program. • 2.1 System Safety and 2.2 Software Safety.—These reports draw heavily from International Electrotechnical Commission (IEC) standard IEC 61508 [IEC 1998a,b,c,d,e,f,g] and other standards. The scope is “surface and underground safety-related mining systems employing embedded, networked, and nonnetworked programmable electronics.” System safety seeks to design safety into all phases of the entire system. Software is a subsystem; thus, software safety is a part of the system’s safety. • 3.0 Safety File.—This report contains the documentation that demonstrates the level of safety built into the system and identifies limitations for the system’s use and operation. In essence, it is a “proof of safety” that the system and its operation meets the appropriate level of safety for the intended application. It starts from the beginning of the design, is maintained during the full lifecycle of the system, and provides administrative support for the safety program of the full system. • 4.0 Safety Assessment.—The independent assessment of the safety file is addressed. It establishes consistent methods to determine the completeness and suitability of safety evidence and justifications. This assessment could be conducted by an independent third party. • 5.0 Safety Framework Guidance.—It is intended to supplement the safety framework reports with guidance providing users with additional information. The purpose is to assist users in applying the concepts presented. In other words, the safety framework is what needs to be done and the guidance is the how it can be done. The guidance information reinforces the concepts, describes various methodologies that can be used, and gives examples and references. It also gives information on the benefits and drawbacks of various methodologies. The guidance reports are not intended to promote a single methodology or to be an exhaustive treatment of the subject material. They provide information and references so that the user can more intelligently choose and implement the appropriate methodologies given the user’s application and capabilities. [ ]

Jan 5, 2003

By R. V. Lundquist

The work described in this report, part of the Bureau of Mines long-range program to develop methods of utilizing submarginal domestic sources of aluminum, was undertaken to investigate the effects of iron in the lime soda sinter process, The approximate Fe2O3 content in a sinter for maximum alumina and soda recovery was 8 to 9 percent. Fe2O3 appears to inhibit gelation, and 15.5 percent Fe2O3 produces effects similar to those produced by 1 percent sucrose. In the lime soda sinter process, aluminum silicates are sintered with limestone and soda ash to yield dicalcium silicate and sodium aluminate. The sodium aluminate is extracted by leaching in caustic solution. The solution is purified by heating in an autoclave with lime to remove silica, and alumina trihydrate is precipitated with carbon dioxide. The reactions involved in sintering and leaching are complex. A number of studies by the Bureau of Mines4-9 and others1 indicate that the iron content of sinters influenced the recovery of alumina and soda and the gelation characteristics.

Jan 1, 1962

By T. A. Henrie, D. C. Fleck, D. G. Kesterke

Uranium metal was electrowon from uranium dioxide dissolved in fluoride melts . The UO₂ was fed directly to the cell in a continuous manner . Electrolysis was performed at 1 , 200 ° to 1,300 ° C in electrolytes composed of UF4 , LiF , and BaFa . A single regulus of metal was collected in a confined area of the crucible . Product purity of 99.8 percent was attained . Carbon was the major contaminant . Compartmented cells were studied as a means of confining the oxide feed to the vicinity of the anodes .

Jan 1, 1964

By T. O. Llewellyn

Laboratory batch and semicontinuous studies showed the feasibility of using methylene bromide and trichloroethylene in heavy liquid cyclone concentration of a Nevada brucite ore. Cyclone tests of minus 20- plus 200-mesh material at specific gravities of 2.42 and 2.44 recovered 71.6 to 74.9 percent of the MgO at grades of 95.5 and 95.4, respectively. Neither increasing the feed pulp density from 5 to 25 percent solids, nor varying feed pressures from 25 to 60 psig had any apparent effect on the heavy liquid separation.

Jan 1, 1971

Three types of communication systems have become popular in solving communication requirements underground: Loud-speaking pager phones, carrier current phones, and magneto ringing phones. Basically, all three are simply single-channel party line systems. Although these systems are quite reliable, the single channel creates a variety of problems. For example- 1. Since no call is confidential, messages are sometimes purposely made vague, especially if accidents or safety topics are being discussed. 2. A potential user must literally "wait in line" until the channel becomes clear for his use; thus, when foremen have to wait to call in reports or supply requests, this single chan-nel creates a serious productivity bottleneck. 3. In many large mines, there are independent branch lines that must be tied together by a dispatcher, adding further delays to the system. To solve these problems, some mines have installed other phone systems-mostly commercial dial phones in industrial enclosures that offer extra channel capacity and private line features. Others have installed a system that combines both dial- and page-phone features in a single unit. Although these do represent improvements, they do not truly solve the overall problems that face modern mines. Besides extra channels, a communication system should have the following features to enhance productivity and safety: 1. A means of paging a roving miner to alert him that he is wanted on the phone. 2. Wireless-to-wired system interconnects by which a miner can talk on the wired phone system by using a remote portable radio. 3. Remote monitors that alert personnel when there is a toxic or explosive gas buildup. 4. Control interfaces that allow remote control of fans, pumps, or other devices. 5. Transmitters and receivers that can serve as emergency links. 6. Loopback that allows an alternate path of communications if the main path is cut. This chapter focuses on equipment and methods to meet the special communication needs of individuals in various places of the underground mine. The communication requirements can be broken down into four categories: 1. The mine entrance (shaft communication). 2. Permanent and semipermanent locations (shop areas, lunchroom, crusher stations, etc.). 3. Mining areas (the room-and-pillar sections, longwall faces, block caving areas, etc.). 4. Haulageways (tracked trolley haulage, diesel, belt haulage). Methods of implementing systems to meet the communication needs of these areas are described in sections 3.2 through 3.5. Section 3.6 discusses methods of satisfying special communication requirements that exist. Major topics in this category include communications with roving personnel, the isolated miner, and motorman-to-snapper communications. Emergency communication systems are described in section 3.7.Detecting and

Jan 1, 1984

This chapter explores leadership behavior in a life-threatening situation-fire in a coal mine. Previous chapters have discussed the database of interviews with miners who escaped from underground fires. Researchers raised questions such as: (1) Who led the miners out of the mine? (2) Did leadership make a difference in the escapes? (3) Was the escape leader the hierarchal leader? (4) What, if any, characteristics did the escape leaders possess? Subsequently, researchers analyzed the mine fire database from a group interaction perspective to address the leadership questions posed. Leadership has been one of the most researched topics of human behavior in the twentieth century. Studies have ranged from individual characteristics of leaders, to situational leadership, to interaction of leader and follower, suggesting different leadership techniques for different followers. The question that emerges here is: Are there different types of leadership that "fit" different kinds of situations? In a crisis situation like that examined in the present study, such information about leadership may significantly improve the chances of escape. To address these issues, the study team looked at the formal authority structure before each fire, considered leadership behavior or lack of leadership during the escapes, and examined those conditions associated with the emergence of leadership. According to Bardo [ 1978], "Emergent behaviors are those forms of action, and the norms, values and beliefs governing those actions, that rise out of the disaster situation." This chapter discusses previous studies in the area of crisis leadership and examines the emergent behaviors of leaders under duress during the mine fire escapes. Previous Studies The research on leadership during emergency situations has consisted mainly of simulation and field studies, with the principal concern being escape from building fires. During the 1980s, Hayashi [1988] created a computer simulation model to evaluate leader behavior in a fire. Although his purpose was to aid in planning for disaster prevention, his findings are relevant because they address the issue of situational leadership in crisis-where a leader changes his or her behavior to fit the situation. Essentially, his simulation model was designed to judge the actions and thinking of leaders. The simulation was tried by 101 subject/leaders 4 times each. The simulation consisted of amaze containing the leader, an informal leader, and 50 evacuees. Interestingly, the results indicated that the leader's actions were not dictated by circumstances. Any differences in behavior were attributed to the individual characteristics of each leader. The study also showed that the worse the situation became, the less individual

Jan 1, 2000

By A. C. Fieldner

The Bureau of Mires in its investigations of gas masks for use in mines and allied industries has studied and developed various types of masks for protection against noxious uses and furies that may be present in atmospheres encountered in mines, metallurgical works, chemical and other industries. As a result of these investigations, the Bureau issued a schedule5 of tests under which manufacturer who voluntarily submit masks for examination and test, are issued an approval certificate for masks that meet the Bureau's specifications. In the Bureau's schedule, masks arc classified by types of gases removed, as type A masks for protection against acid gases; B; organic vapor; C, ammonia; D, carbon monoxide; E, smoke, dust, and mist; F, special gases; combination types, and type N, for protection in air against all gases, vapors, and smokes. The purpose of this paper is to describe the physical and chemical tests that were conducted on a type N mask, the protective principles and construction of the essential elements of the canister and attachments, and the uses and limitations of this type of mask. The mask tested is known as the all-service mask, manufactured by the Mine Safety Appliances Co., Pittsburgh, Pa;, and was approved (approval No. 1403) by the Bureau on July 1, 1924, for protection from all classes of poisonous vapors, gases and smokes in air.

Jan 1, 1925

This Technical Memorandum Report is a collection of three working memoranda, prepared during the course of our work for the Bureau of Mines and bound together for convenient reference. These working memoranda present preliminary performance estimates, for baseband voice and narrow- band through-the-earth electromagnetic communications systems of principal interest to the Bureau, for operational/emergency mine communications. The calculations were prepared to obtain early indications of the feasibility and governing parameters of such communications systems. They are based on limited, but pertinent, coal mine electromagnetic noise data acquired to-date by Bureau of Mines contractors; and of theoretical signal-attenuation characteristics for two transmitter antenna types of present interest to the Bureau. The memoranda examine the cases of baseband voice and narrowband communications for uplink and downlink transmissions, for frequencies up to 3kHz. Downlink transmissions are via a horizontal wire antenna, up- link transmissions via a vertical-axis loop antenna, for typical mine depths of 300, 600, and 1000 feet. Representative coal-mine overburden conductivities of 10-2 mhos/meter (moderate and common) and 10-1 mhos/meter (high) were used; for voice and narrowband, 10-1 for narrowband only. Examples of high, moderate, and low; surface and subsurface; harmonic and broadband-impulsive noise conditions were taken from NBS and Westinghouse (WGL) mine noise data, together with examples of high- and low levels of ELF atmospheric noise taken from M.I.T. Lincoln Laboratory data. These feasibility calculations are not intended to serve as definitive and complete treatments, but as a starting point: to establish first-order estimates of the magnitude and variability of transmitter power requirements under different noise, overburden conductivity, and mine depth conditions; to identify relationships, conditions, or frequencies that are likely to limit or enhance system performance; to reveal items requiring further investigation and data still required; and to suggest practical methods for optimizing system performance. These objectives were met by the calculations. Simple experiments to support these calculations can and should be carried out; together with more detailed investigations of specific modulation, coding, noise-suppression, voice-compression and signal-conditioning techniques, aimed at producing through-the-earth operational/emergency mine-communication systems that are not only effective, but practical and economically sound.

Jan 3, 1972

By John J. Henn

Two lime sinter processes for recovering alumina from clay, the double-leach process and the single-leach process, are evaluated in this Bureau of Mines report. In both processes, clay and limestone are mixed and sintered to form calcium aluminate from which alumina is extracted as sodium aluminate by leaching with a dilute solution of sodium carbonate. The pregnant liquor is desilicated, then carbonated to precipitate alumina trihydrate which is recovered and calcined to a,-alumina. The fixed capital costs for plants producing 1,000 tons per day of alumina are $85 million for the double-leach process and $86 million for the single-leach process based on a Marshall and Stevens chemical equipment index of 240.0. Because plant locations are variable with respect to the proximity of clay and limestone deposits, a nomograph is included to determine operating costs at various delivered costs of clay and limestone. For plants at which the delivered cost of clay containing 30 percent A1203 is $2 per ton and the delivered cost of limestone is $1 per ton, the operating costs are $81.04 and $89.87 per ton of alumina for the double-leach process and single-leach pro-cess, respectively.

Jan 1, 1969

By R. E. Head

At the microscopic laboratory of the Bureau of Mines Intermountain Experiment Station, Salt Lake City, Utah, efforts are being made to devise methods of differentially coloring finely crashed minerals as a means for their identification. Staining would facilitate sight recognition of minerals under the microscope and would be of great value in the study of crushed ores, concentrates, and tailings. Since the treatment of ores for their beneficiation is primarily based on the recovery of the minerals containing the clements of value, it is extremely important that these minerals should be known and that a method for quickly determining them when in minute fragments should be available. Herein lies one of the greatest uses for color methods. In many cases it is a difficult matter for even the trained petrographer and mineralogist to identify finely crushed minerals quickly. Although ordinary petrographic methods are accurate, they are often time--consuming and are not suitable to the needs of millmen who require, especially in the examination of tailings a method for determining minerals by inspection.

Jan 1, 1929

By W. A. Selvig

The experiments described herein were made at the request of Committee D-5, on Coal and Coke, American is n Society for Testing Materials, in order to obtain data as to the probable contamination of laboratory samples of coke Then pulverized to pass a No. 63 sieve of tine U. S. Standard Sieve Series2 by methods other than by ball-mills or hard-steel diamond mortars, which methods are specified-in the standard methods of that Society.3 After pulverizing, representative samples were analyzed by the Bureau of Mines at Pittsburgh for ash content to detect any contamination of the samples by the pulverizing apparatus. Preparation of Core Samples for Tests. Two samples of 48-hour beehive coke (Continental and Leisenring) made from Pittsburgh coal were selected for the tests. These cokes were crushed approximately to No. 10 sieve size, by first passing through a jaw crusher and then through a, roll crusher. The crushed coke was then carefully mixed and riffled into portions of about 800 grams each, and sent to three cooperating laboratories for grinding, through a No. 60 sieve. Size tests on these samples shoved the fineness to be as follows: [ ]

Jan 1, 1925

By Dean H. Ambrose

A computer model was created that generates contact data by means of simulation while altering several variables associated with the machine and its operator. These variables include work environment, the operator's anthropometry, work posture, choice of risky work behavior, and the machine's appendage velocity. In the model, a contact means two or more objects intersecting or touching each other, e.g., the appendage colliding with the operator's hand, arm, head, or leg. This report documents the code development of special features of the computer model, random virtual human motions and behaviors, which made it possible for researchers to study hazardous interactions, such as contacts between the operator and machine. The original idea for random virtual human motions began with the need for a model that, when simulated, would experimentally mimic machine and human actions that could cause actual injuries or fatalities in the workplace. Injury incident investigation reports do not usually contain enough information to aid in studying this problem, and lab experiments with human subjects are also not feasible because of safety issues and ethical issues. Early investigation that evaluated the feasibility of random motions resulted in a primary programming structure and building blocks for code expansion. Basic motions and standard derivation data provided random parameters for the operator's movement in the random motion code. Experimenting with basic motions in preliminary models helped researchers devise a random motion technique that worked with xyz motion parameter values from basic motion parameters. Both values were the building blocks used in motion commands that comprised the core of the random motion code. When the code is executed in a three-dimensional computer model, it generates realistic starting positions for the operator's (virtual human) body and body parts and realistic motions mimicking a work sequence with a valid range of variation in movements. Researchers developed several rules for the random motion technique that, when applied, will maintain directional integrity of a virtual human's basic motions. From previous research, researchers formulated the algorithm that determines the behavior during machine operation. The decision algorithm was needed by the random motion code to randomly select what behavior to use for a simulation execution for a realistic representation of the operator's motions and risky behaviors during work tasks. The operator's chance of avoiding the moving appendage was also a concern to ensure that data reflecting a near-miss would not be considered a contact. Therefore, to filter a database obtained from simulations for actual contacts, it was necessary to track the operator's field of view and determine from this information when the appendage is in and out of the operator's view. NIOSH researchers successfully applied random motions and risky behaviors to examine the speed range of a roof bolter machine appendage for different workplace scenarios and compare statistically which is most likely to cause contacts (and possible injuries) to miners. Researchers in this study believe that the use of such simulations, treated with advanced statistical procedures, are extremely useful tools to evaluate the hazards of tasks where it is not possible to perform experiments with human subjects.

Jan 3, 2004

By Lippe D. Sadwin

A high-speed streak camera method for making equation of state measurements (shock and particle velocities) on samples of rock under dynamic load conditions is described. Experimental data are given for tests on 12 samples representing 5 rock types. Analysis of these data shows that the method is practical and that good reproducibility of results can be obtained. The pressure range covered in the tests was from 1 to 50 kilobars.

Jan 1, 1966