Search Documents

By Robert F. Chaken

The National Institute of Occupational Safety and Health (NIOSH) is dedicated to achieving "safety and health at work for all people -- through research and prevention." An important procedure in pursuing this goal is the NIOSH surveillance studies where the number of injuries are monitored according to demographic, employment, and injury characteristics. These numeric data are then used to identify injury risk factors, develop safety programs, and monitor implemented remediation methods. In essence, ongoing surveillance data form the bases for directing the resources of NIOSH in setting of research and prevention priorities, and in evaluating safety procedures. This surveillance techmque, which is based on the Public Health Service approach to identification and control of disease (1, 2, has been used quite successfully in dealing with relatively high number injuries such as hearing loss, musculoskeletal disorder, respiratory disorder, falls, etc. (2). However a problem arises when extending this paradigm to lower frequency traumatic events; particularly those often referred to as disasters (i.e., high impact events like mine explosions, airplane crashes, etc.). One can ask the question - there hasn't been a coal mine fire fatality in the U.S. for over ten years, to what extent should we be concerned with mine fire safety (resource-wise)? - The National Traumatic Occupational Fatalities (NTOF) system (4J which NIOSH uses to survey occupational fatalities annually, would suggest that underground mine fires would not be a high priority item in occupational safety. Yet, miners' (i.e., the exposed workers) do consider mine fires and explosions to be major safety concerns. I believe that we need to rethink our evaluation of work place disasters, what is worker exposure, and what are the underlying assumptions (both explicit and implicit) as to the impact that economic, societal and degree of hazard factors make on risk evaluation. The answers to all these problems, will require much broader considerations than those in current surveillance safety and health models. This paper discusses some facets of those considerations.

By Thomas C. Ruhe

The Bureau of Mines conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) saves energy, reduces oil imports, and reduces mining costs. Low ambient temperatures may cause these recycled oils to become too viscous for proper absorption by ammonium nitrate (AN) prills and result in poor blast performance, safety hazards, and environmental problems. To help quantify and resolve these issues, viscosity, mixing, and performance tests were conducted at various temperatures. Diesel fuels No. 1 and No. 2 were studied separately and in blends with 25,50, and 75% RO. Good quality ANFO mixes (94-6) were produced with dry absorbent prills and blended fuel (No. 1 diesel plus RO) at temperatures as low as -40°F (-40°C) with 75% No. 1/25% RO, and at -20°F (-29°C) with 50/50. Diesel fuel No. 2 also made good mixes as low as -30" F (-34°C) with 75% No. 2/25% RO, and at 0°F (-18°C) with 50/50.

Jan 1, 2008

By Donald R. Irving

THIS CHAPTER is new to the Minerals Yearbook and will appear regularly hereafter. Its purpose is to present statistics that reflect technologic trends in the minerals and metals industries (except fuels). Much useful information has been collected annually through the Bureau of Mines mineral commodity and employment and injuries canvasses. However, these data must be supplemented by further data to permit evaluation of the type, direction, and rate of technologic change, which are vitally important in long-term mineral planning. In addition to, and fully as important as, expanding the available data is the need to ascertain that the various items collected are obtained from identical reporting units, to enable direct comparisons to be made.

Jan 1, 1960

By B. P. Martinez

This report presents the results of a research and development program in recovering waste-rolling oils conducted by the Bethlehem Steel Co., before 1954 at its Sparrows Point plant, Sparrow Point, Md., with the cooperation of the Bureau of Mines, U. S. Department of the Interior, College Park, Md. The objective of the program was twofold: First, to recover oil for reuse in the plant; and second, to stop pollution, by oil, of the stream and harbor areas in the immediate vicinity of the plant. The sequence of the investigations was laboratory and pilot plant studies on sedimentation, simple aeration, and flotation for the separation of oil and water; and construction of a production unit using standard flotation equipment. This work was only preliminary for the Bethlehem Steel Co. and it has continued research on this problem. Recent progress indicates that new, improved processes will soon replace the flotation units described in this report. The first efforts to separate oil and water by simple sedimentation were unsuccessful. To establish the cause of this failure, microscope examinations and measurements were made on cold-reduction rolling mill cooling-water effluents containing oil in suspension. It was discovered that an average oil globule, held in suspension, was only 0.001 inch in diameter and would not coagulate with other globules for normal sedimentation at room temperature. The next step in the sequence of studies was to coagulate the oil suspension by simple aeration with air under slight pressure. The aeration methods studied were effective in removing up to 68 percent of the total oil but were approaching flotation in principle. The final investigation of the series was flotation of the oil in conventional laboratory-size flotation cells. The small-bubble method, without reagents, floated up to 89 percent of the total oil held in suspension and was the process selected for pilot-plant development.

Jan 1, 1959

By Dana Reinke, Launa Mallett, Michael J. Brnich

Some segments of the mining industry, especially underground coal, have seen a large influx of inexperienced miners in recent years. It is anticipated that this trend will reach other mining segments over the next 10 years. This paper discusses the training needs of the younger generation of inexperienced workers who have just entered or are soon to enter the mines. Currently, many trainers are of the so-called Baby Boom generation. Can these different age groups learn to communicate across the generation gap? Even trainers who have been highly effective in the past should reassess their training styles and their classroom materials to determine if they are prepared to meet the needs of these new trainees.

Jan 1, 2002

By Peter F. Strong, Robert L. Lagace, Alfred G. Emslie

This paper is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a comer. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency that propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center's investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1973

By F. W. Wood

Ingots of zirconium and other highly reactive metals such as titanium and hafnium produced by the consumable-electrode arc-melting process require conditioning before forging or rolling. A nondestructive, arc-conditioning technique has been developed as a substitute for lathe conditioning. The technique employs en electric arc under an inert atmosphere to fuse surface metal on the sidewalls of ingots without seriously affecting the general quality of the ingots. Advantages of the practice are Increased yields, lower accumulation of inferior scrap, and actual cost savings. The work cited in this report was done on zirconium. INTRODUCTION The consumable-electrode arc-melting process as practiced at the Bureau of Mines3 4/ has proved to be a technique for producing sound, homogeneous, commercial-size ingots of zirconium and its alloys. Ingots produced by this process, however, have as a characteristic a layer of partly fused metal on the sidewall to a depth of 3/16 to 3/8 inch. To prevent extension of surface imperfections during forging, the ingots are ordinarily conditioned by removing defective material in a lathe. If the metal were less reactive or the requirements less severe, the machine chips could be recycled and remelted. However, zirconium, being so oxygen sensitive, is contaminated by merely being machined despite extensive cooling of the tool bit. Further, being contaminated with oxygen, the chip metal upon remelting is 10 to 25 Brinell-hardnese numbers harder than the ingot from which it was machined. For this reason, the ingot specifications for naval reactor use have prohibited remelting machine chips, except as required for starting pads. Again, were zirconium less costly or less in demand this ever-increasing pile could be burned to oxide and recycled through the Kroll sponge process. Economics do not favor this, as melting feed stock has an estimated increase In value over oxide of about $8.80 per pound of contained zirconium. The efforts of the Bureau to solve the problem have been directed along two lines: To reduce the contamination of the machine chips produced and to reduce the quantity of the chips produced. This paper presents the technique developed to reduce the quantity of chips produced by arc-conditioning the remelted ingot.

Jan 1, 1955

By C. Travis Anderson

"A recent critical study by Ralston3 of the iron system points out the importance of and necessity for work upon the preparation of ferrous oxide. Not only are ferrous oxide samples desired for determination of the important physical and chemical properties, such as specific heats and heats of formation, bat also information on the stability and behavior of this material is of considerable technical importance. Related. problems where the properties of Fe0 are important have to do with desulphurization of iron, the formation and occurrence of magnetite in copper smelter slags, and sulphur elimination in copperFerrous oxide also has valuable catalytic properties, as is demonstrated in nitrogen fixation.Pure ferrous oxide has never been prepared in quantities large enough to furnish adequate physical and chemical data on its properties. Only two or three experiments4 have produced a fraction of a gram in a state approximating purity and have collected evidence that has been sufficient proof of their having done so. Ferrous oxide is stable only above about 570°C., and below that splits into magnetite and iron according to the reactionUp to about 1920, those who had endeavored to prepare FeO made no provision for rapid chilling, so that although their product. may have had the proper iron oxygen ratio for FeO, in reality it-probably did not consist of pure FeO. The above reaction is reversible; above 570oC. magnetite and iron are supposed to recombine almost completely, and if so, should constitute a direct and easy method of preparation. The data, however, were somewhat conflicting, and the extent to which the reaction goes in either direction needed checking. Preliminary experiments on the interaction of molten Fe304 with solid Fe gave Fe0 of about 85 per cent purity, corresponding to. the approximate purity obtained by some previous investigators. The present work is concerned chiefly with the results cf repeated interaction between partly reduced magnetite and iron, and the calculations which may be made from such results. Repeated treatments are necessary, because molten impure ferrous oxide and iron can not be kept in contact for more than short periods of time."

Oct 1, 1928

By Christopher C. Jobes, Alan G. Mayton, Farid Amirouche

Based on prior mine vehicle studies of operators’ exposure to whole-body vibration, researchers from the National Institute for Occupational Safety and Health (NIOSH) evaluated four seat designs on mine haulage vehicles, with regard to roadway-induced jarring/jolting and operator comfort. Investigators collected objective and subjective data from vehicle operators on two existing and two NIOSH seat designs. This study included time and frequency response data using accelerometers and a data recorder, operator perceptions of jarring/jolting and discomfort levels using a linear visual analogue scale, and data from a questionnaire developed for this study. Results from the analysis of subjective data show that operators generally favoured the NIOSH-designed seats over the existing seats. The results of analyses from the absorbed power method and the threshold limit method, based on ISO 2631-1 (ISO, 1985), support the premise that NIOSH seat designs are superior to the existing vehicle seat designs on both models of mine shuttle cars used in the study. The NIOSH seat designs, featuring viscoelastic foam padding, were more effective in reducing vibration energy for operators exposed to vehicle jarring/jolting. In this paper, the performances of the NIOSH and existing seat designs are compared relative to the operator’s exposure to vehicle vibration (mainly jarring/jolting).

By Albert E. Long

Diamond-bit performance and cost data accumulated in core-drilling sandstones reveal significant trends of economic interest. Large-size, AA-Grade drill bort suffered less diamond loss per foot drilled than any other size or grade of diamonds assessed. Detailed analyses of the factors that affect diamond-bit performances -diamond size, diamond quality, bit size, bit type, percentage of core recovered, and physical characteristics of bit matrices -are assessed in the tables, graphs, and discussion. INTRODUCTION Since 1945 the Bureau of Mines has been compiling detailed performance records on diamond bits used in core drilling throughout the United States and Alaska. Analytical reports covering bit performance in various rocks are issued as in-formation on a significant number of bits used in anyone type of rock is accumulated. The first three such reports analyzed bit performance in gneiss,2/ schist,3/ and lime-stone and dolomite.4/ This report evaluates diamond-bit performance in sandstone. Data obtained from 627 bits, which drilled 42,665 feet on 45 different projects, are presented. The geographical distribution of the projects is shown in figure 1.

Jan 1, 1958

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

APPENDIX G TABLE IX MINE A 1 General Total Employees 3000 Maximum No, of Men Underground/Shift 800 Shifts/Day 3 Type of Ore Copper Daily Production (TPD) 25,000 Mining Method Room and Pillar Vein Dip/Thickness l0°/l5 ft Number of Levels/Max Depth 1/0 to 1800 ft 2 Haulage, Conveyances and Travelway Main Haulage Rubber Tire/10 miles belts Man-Ways - Typical Route of Travel to most Remote Sites Rubber Tired Vehicles Hoists - Capacity/Speed/Depth Depth under construction 3 Ventilation 2,500,000 cfm - 5 surface fans 4 Compressed Air N/A cfm 10" and 12" lines 5 Incendiary Storage 2 day powder 1000 gal fuel oil 6 Communications 1 complete system - all shops, dinner areas, and feeder/breaker stations 2 partial systems 7 Escapeway- Systems Man Check System Section boss log and punch cards Alarm System Mine phones with paging system Posting of Escape Route Maps No Escape Signs Every intersection, fluorescent paint Evacuation Drills 2/yr/shift Refuge Chambers - 1 cinder block - No longer required

Jan 1, 1976

By D. G. RUNNER

Information Circular 6148R, " Selected Bibliography of Minerals and Their Identification ," was issued in June 1929 , revised in July 1937, and again in October 1938. The popularity of this circular , combined with the desire to make it more comprehensive , has occasioned the preparation of this compilation of references . Where possible , date of publication , publisher, current price , and number of pages are given, although prices are subject to change at intervals . The references are grouped under the following headings : minerals , gems , rocks , geology, geomorphology, engineering geology , prospecting, mining . engineering, microscopy, technical dictionaries , and miscellaneous . For ready reference, the authors ' names are arranged alphabetically under each grouping . This list is not comprehensive, but contains only those references in most common use and which are generally available in public college libraries .

Sep 1, 1949

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least-radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By J. Wade Watkins

One potential peaceful application of nuclear explosives is stimulating the production of liquid or gaseous hydrocarbons from essentially nonproductive deposits of petroleum, natural gas, oil shale, and tar sands. Within the United States the appreciable difference between producible proved reserves and ultimate reserves and resources of hydrocarbon deposits is of such magnitude that much petroleum, natural gas, shale oil, and bitumen will not be produced unless significant technological progress is made in production techniques. The shattering effect of contained nuclear explosives and, to a lesser extent, the heat produced, have been considered as stimulative forces when the thickness, depth, and nature of such deposits permit considering the use of nuclear devices. Mechanical production problems would be less in an oil or gas reservoir than in an oil-shale or tar-sands deposit. Also, tar-sands resources in the United States may not be adequate to warrant serious consideration of applying nuclear-explosives stimulation. Gas reservoirs should present the least- radioactive-contamination problem. The technical feasibility of using nuclear explosives cannot be evaluated fully at present. Additional information is needed on the effects of pressure, heat, and radioactivity on the solids and fluids of hydrocarbon deposits, the nature and extent of induced fractures in different rock media, and the possibility of isolating and confining or removing radioactive contaminants. Final technical feasibility can only be determined by a field test. If technical feasibility is established, economic feasibility will depend upon the comparative cost of producing hydrocarbons by nuclear explosives and by conventional means. It is probable that an economic comparison would favor nuclear stimulation only where devices of relatively high yield could be used practicably and safely.

Jan 1, 1964

By Linda L. Chasko, Larry D. Stowinsky, Ronald S. Conti

Mine operators often rely on mine rescue teams to save lives during an underground emergency such as an underground fire, explosion or roof fall. It is extremely important that team members are provided with adequate exploration equipment and that training simulations are conducted in a realistic manner. A series of mine rescue training exercises was developed, conducted and evaluated by the National Institute for Occupational Safety and Health (NIOSH) in cooperation with the Pennsylvania Department of Environmental Protection, Bureau of Deep Mine Safety. The exercises were conducted at NIOSH’s Lake Lynn Laboratory during 1995 to 1998 and resulted in improved technology and training for mine rescue teams. For example, existing technologies were identified to help rescue teams during exploration. These included chemical light sticks to identify team members and mark crosscuts and mine materials, strobe lights for mapping out escape ways, and a helmet mounted thermal imaging system to see through smoke. A hands-free communication system showed potential for enhanced communications between team members and the fresh air base. A new high-visibility team lifeline that allows for flexibility of movement between team members was developed. A positive-pressure inflatable escape device (IED) was used to isolate the “hazardous” environment from fresh air and allow rescue team members to traverse through. An inflatable feed-tube partition that can rapidly block large openings such as underground passageways and simultaneously provide a feed-tube for high-expansion foam generators was also deployed for several simulations. During the simulations, mine rescue team members donned self-contained breathing apparatuses (SCBA) and traversed more than 305-m of mine passageways filled with nontoxic smoke. Visibility ranged from 0.3 to 0.9-m. In one area of the mine, a kerosene heater was used to simulate a fire and reduce the oxygen concentration. In another area, a 1.5 pct methane zone was established. The team members searched for "victims,” mapped the passageways, built temporary stoppings and ventilated the smoke-filled entries. The teams indicated that the simulations were challenging and very informative.

By E. L. Litchfield

This report of work by the Federal Bureau of Mines has two primary objectives: A survey of the present status and usefulness of the minimum ignition-energy concept, and the presentation of recent data that are believed to bear on the safety problem associated with the ignition of combustible gases by electric discharges. The minimum ignition-energy concept has widespread applicability, especially to safety. The primary obstacle in making theoretical calculations of the requisite ignition energy is the lack of data on chemical kinetics and flame hydrodynamics. The new data on electrical ignition are representative of the great increase in knowledge that can be achieved by proper utilization of geometrical and electrical characteristics associated with the ignition source. CONCEPT OF MINIMUM IGNITION ENERGY The basic concept of a minimum ignition energy (the minimum amount of energy required to cause ignition) follows quite naturally from general physical principles and from the stability (lack of chemical reaction) of the gaseous mixture under the initial conditions. It also follows that if, as a first condition, lossless, instantaneous, and spatially localized energy can be injected and, as a second condition, the relaxation time for conversion of this type of energy to the type required for the reaction is short compared to some characteristic time scale of the ignition phenomenon, the energy requirements will be essentially independent of the type of energy source. Even if condition one cannot be fulfilled, it is sometimes possible to estimate the energy content of the gas required for ignition, and under these circumstances, condition one is fulfilled in effect. There are several instances where results can be interpreted for circumstances that effectively satisfy conditions one and two; these will be discussed later.

Jan 1, 1960

By D. C. Fleck

The Bureau of Mines, in a cooperative research program with four lead companies, has investigated ferric chloride leaching of galena to prepare lead chloride for molten-salt electrowinning to produce lead metal. The hydrometallurgical-electrolytic process is an alternative to the sintering-smelting-refining process currently used to produce lead metal and avoids the environmental problems associated with a conventional smelter. During investigations on the electrowinning aspects of the work, it was noted that certain cations, moisture, and sulfate in the electrolyte affect lead metal purity, cell voltage, current efficiency, and viscosity of the electrolyte. Results of bench-scale tests are re-ported on the effects of CaCI2, CuCI2, FeCI2, MgCI2, NaCI, ZnCI2, PbS04, and moisture on electrolysis. As impurities increased in the electrolyte, current efficiency decreased. CaCI2, CuCI2, and FeC12 decreased current efficiency by 12 to 47 pct. ZnCl2 gave a small voltage increase, while CaCI2 addition equivalent to 4.9 pct Ca caused a 50-pet increase in voltage. The lead metal was contaminated in direct proportion to the CuCI2 buildup in the electrolyte, Anode corrosion was observed with MgCI2 and MgC12?6H20. Viscosity increased appreciably with the buildup of NaCI, CaCI2, and sulfate. Electrolyte foaming occurred with ZnC12, MgC12?6H20, MgC12, FeC12?2H20, and FeCI2. Moisture inhibited the coalescence of the lead metal.

Jan 1, 1983

By P. C. Good

The work reported here was undertaken by the Federal Bureau of Mines to investigate new methods of preparing high-purity metal. Tungsten hexachloride was prepared by direct chlorination of scrap tungsten metal and by treating tungstic oxide with carbon and chlorine. The resulting tungsten hexachloride was purified by distillation and reduced win: sodium, magnesium, or hydrogen. The metal prepared by these techniques was at very high purity after arc melting but of variable quality prior to arc meIting. Metal recovery ranged from about 40 to 90 percent of theoretical values, It was found possible to deposit a smooth, dense coating of high-purity tungsten on the inside of a heated tube by vapor-phase reduction of tungsten hexachloride at reduced pressure.

Jan 1, 1961

By Oliver Bowels

Many inquiries are received by the United States Bureau of Mines for the names of elementary books on geology, mineralogy, methods of identifying minerals, prospecting, and similar subjects. In response to this demand the following brief bibliography has been prepared. As many of the inquiries are received from those who have limited technical knowledge of the subjects involved, the bibliography includes the simpler texts which present the subjects in nontechnical language. Other texts contain glossaries which define the technical terms used. A short note following the title indicates the character of each book, the number of pages, and the price. Thus, elementary mineralogists or geologists, prospectors, mineral collectors, nature students, or travellers may select the texts that best suit their requirements and their capabilities. To supply the needs of more advanced students, quite a number of the standard texts used in schools and colleges are included in a second group. A short list of books on economic geology and mineralogy has also been added.

Jan 1, 1929

By Franklin P. Hall

U.S. supply and demand data for utility electricity by States and regions were tabulated for the years 1960 and 1965. Estimates are provided of State-by-State quantitative data for the utility electricity industry that can be integrated into State and regional energy balances by source, form, and major consuming sectors, and used to determine basic flow-patterns. The difficult problem of compiling interstate and interregional shipments of electricity was resolved by (a) assuming the negligibility of interregional shipments and (b) deriving a theoretical line loss percentage used for determining interstate shipments. The data developed were able to show an estimated total supply of utility electricity available for consumption. The tables also report the distribution of the supply among the major consuming sectors (household and commercial, industrial, and transportation). To compare the various energy sources of utility electricity, quantities were converted to their British thermal unit (Btu) equivalents. The Federal Power Commission, Edison Electric Institute, and Bureau of Mines are the sources of the data used in this study.

Jan 1, 1969