Search Documents

By Thomas P. Mucho, Dennis Dolinar, Christopher Mark

During the 1990s, the former U.S. Bureau of Mines conducted a number of field studies in which the performance of different types of roof bolts were evaluated in different geologic environments. The studies used a standard suite of measurements, including multipoint extensometers, strain-gauged roof bolts, and roof bolt load cells. The sites were chosen to investigate the effect of a variety of parameters, including installed tension, bolt capacity, grout annulus, and horizontal stress orientation. Although not fully successful, the measurements provided valuable insights into each of these issues. They also showed that instrumentation and monitoring have important advantages over observational methods for comparing the performance of different roof bolting systems.

Jan 10, 2000

By J. W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and from the data developed to determine: 1. Which coals either as mined or after beneficiation by conventional preparation are chemically suitable under present standards for producing metallurgical coke. 2. Which coals require special and more intensive treatment in preparation than is now practiced. 3. Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation by present-day methods. This report is one in this county series that describes the preparation characteristics of the coals of Lee County, Va.

Jan 1, 1957

By E. G. King

Heats of formation of three crystalline oxides of rhenium (Re02, ReO3 and Re207) have been determined by the method of solution calorimetry, using an aqueous perchloric acid--ceric perchlorate solvent. Copper metal and cupric oxide were utilized as auxiliary substances. Heats were determined at 298' K for the reactions Re + 2CuO = Re02 + 2Cu, Re + 3CuO = ReO3 + 3Cu, and 2Re + 7CuO = Re207 + 7Cu. Standard heats of formation were derived using the value of -37.23 ±0,15 kcal/mole as the heat of formation of CuO. The standard molal heats of formation of the rhenium oxides were determined: Re02, -107.3 ±0.8 kcal; ReO3, -140.8 ±0.9 kcal; and Re207, -301.9 ±1.8 kcal.

Jan 1, 1969

By John A. Johnson

"INTRODUCTION The use of wet drilling with adequate ventilation has largely controlled production of dust in drilling rock; however, in some operations, such as shaft sinking and modern tunnel driving, when each of a number of drills is operating in a small cross-sectional area, it is at times difficult to ventilate well enough to keep the dust concentration within desired limits.Some chemical compounds, known as wetting agents, when added to water in small quantities reduce the interfacial tension and make it possible for the solution to wet dust particles more effectively than water alone.This report presents results of tests on the effectiveness of two wetting solutions in reducing the amount of dust produced by wet drilling in basalt.ACKNOWLEDGMENTSThe tests were conducted at the Bureau's Mount Weather Testing Adit, Mount Weathe, Va. The author acknowledges the assistance and cooperation of Wing G. Agnew, superintendent; Marvin M. Reveille, mining-ngineering aide; and the rest of the crew at Mount Weather in conducting the tests. C. W. Owings, mining engineer, Safety Division, assisted in conducting some of the first tests and gave valuable advice and guidance throughout the work and in preparing this report."

Jan 1, 1943

By Nancy S. Raymon

The Bureau of Mines investigated the effect of controlled additions of selected metal oxides, as well as the adjustment of the calcia-to-silica ratio on the high-temperature strength of refractory-grade periclase. Increases in the hot flexural strength of some periclase materials in the range of threefold to fourfold were obtained with additions of Zr02 and by adjustment of the CaO:Si02 ratio to the 2.5 to 3.0 level. Results show that for each periclase refractory raw material, there exists a combination of level of Zr02 addition and an adjustment to the CaO:Si02 ratio that optimizes the hot flexural strength of each of these materials. Data also indicate that the improved hot strengths can be attributed to the high-temperature secondary phases formed between the different levels of periclase impurities and the additives, resulting in improved intergranular high-temperature bond strength.

Jan 1, 1982

In the past, mine management has been concerned with removing water from active mining sections primarily because it hampered the movement of mining equipment and aggravated the working condition of the miners. Pumping water to sumps and gravity drainage by ditching have proven successful in mines for minimizing section down time due to water influx. However, with the advent of more strict pollution laws the mining engineer must now be concerned with keeping water out of the section and also with preventing it from causing pollution. A review of the handbooks and textbooks used in the mining engineering curricula reveals that little has been written concerning acid mine water prevention or control in underground coal mines. Additionally, the review of the curricula of mining schools indicates they are not teaching the engineering students the necessary techniques of mine water management as they relate to the abatement of mine water pollution.

Jan 1, 1970

By Fred N. Kissell, J. E. Matta, J. C. LaScola

The methane gas emitted from coal samples collected from the conveyor belts dumping into silos was measured by the Bureau of Mines. Approximately 50 pct of the total gas desorbed into a sealed can within 1 week was released during the first 24 hours. No simple correlation between the gassiness of the coal stored and the methane concentration in the silo open space above the coal was found. This was probably because the gassier coals were stored in open-top silos, which were better ventilated. Although the methane concentration in the open space above the coal pile was less than 1 pct for all 34 silos investigated, a methane measurement in the coal pile showed that high methane concentrations can exist. The methane released in the pile appears to accumulate and not liberate freely into the open space above the coal pile. Probably this gas is released during reclaiming operations, but further research is required to substantiate this claim.

Jan 1, 1978

By Michael J. Sapko, Gregory M. Green, Harry C. Verakis, Kenneth L. Cashdollar

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted a joint survey to determine the range of coal particle sizes found in dust samples collected from intake airways of U.S. coal mines. The last comprehensive survey of this type was performed in the 1920’s. The size of the coal dust is relevant to the amount of rock dust required to inert the coal dust, with more rock dust needed to inert finer sizes of coal dust. Dust samples were collected by MSHA inspectors from several mines in each of MSHA’s ten bituminous Coal Mine Health and Safety Districts. Samples were normally collected in several intakes at each mine. The laboratory analysis procedures included acid leaching of the sample to remove the limestone rock dust, sonic sieving to determine the dust size, and low temperature ashing of the sieved fractions to correct for any remaining incombustible matter. The results indicate that particle sizes of mine coal dust in intake airways are finer than those measured in the 1920’s. The significance of these finer coal dust sizes is discussed relevant to the amount of rock dust required to prevent coal dust explosions.

By R. S. Conti, C. D. Litton

This U.S. Bureau of Mines (USBM) report discusses the results of research conducted in the USBM experimental mine at its Lake Lynn Laboratory to determine the alarm times of smoke and carbon monoxide(CO) sensors, and a point type heat sensor (PTHS) to slowly developing coal-conveyor belt fires. The tests were conducted at air velocities of 0.44 and 0.97 m/s. The data clearly indicate that smoke sensors provide earlier warning of fire than 10 ppm CO sensors, and that 10 ppm CO sensors provide earlier warning than PTHS. A success rate of 1.0 (indicating detection of every test fire) was obtained for both smoke and CO sensors. For the PTHS, the success rate was 0.57 at the lower air velocity, decreasing to 0 at the higher air velocity. Data are also presented showing the sequence of fire events and detection events at the two air velocities as a function of time. Results show that early detection and warning of underground mine fires will improve the probability of miners’ escape.

Jan 1, 1995

By C. M. K. Boldt, R. L. Levens, A. D. Marcy

Researchers at the U. S. Bureau of Mines conducted investigations to evaluate the potential for ground water contamination by mine waste used as backfill. Samples of cemented waste backfill and water discharging from drillholes and seeps were collected to use in chemical analyses and laboratory tests to determine the physical and chemical factors that control release of heavy metals to ground water. Greater water retention by cemented backfill (as compared to uncemented sandfill) reduces the surface are aexposed to oxidation, which in turn reduces the amount of acid produced. The acid is neutralized by the cement and minerals contained in the backfill. The grain-size distribution of tailings used for backfill affects the structural integrity of cemented backfill under attack by acidic water; breakdown of the backfill structure releases neutralizing materials faster. Backfilled stopes in rock with low hydraulic conductivities will constitute preferential flow paths after mine flooding; however, the rate of flow through backfill will be much slower than when the stope is partially saturated during mine operation. Considering all factors, acid generation and release of metal ions from cemented backfill should be less than in uncemented sandfill.

Jan 1, 1995

By Ronald D. Hill, Elmore C. Grim

Mining as an extractive process alone is outdated and unacceptable to today's environmentally concerned public. Multiple land use must be considered as well. Only through effective preplanning can the full potential of reclamation result in a lasting asset for future generations. The coal industry is now recognizing that reclamation of mined lands is part of the mining cycle that must be planned and carried out in a timely and orderly manner. It is also finding that planning reclamation in advance of mining is cheaper and more effective than waiting until mining is completed. The decision to open a strip mine must be based on the results of studies to determine if successful reclamation can be achieved and whether the economic benefits to the company will be justified(1). Information regarding the physical, chemical, hydrologic and biologic systems operative at the site must be under- stood or reclamation will be a failure. Working together, engineers, management and reclamation specialists should design the actual mining and reclamation plan before mining is begun.

Jan 1, 1974

By Jack C. White

Studies were made to determine the character and distribution of the copper lost in copper mill tailings. Acid soluble (oxide) and acid insoluble (sulfide) copper were determined for heavy-liquid sink and float products of screen-sized fractions from 12 copper mill tailings. In most of the tailings studied, the coarse-size fractions are higher in copper grade than the respective bulk tailings, high in sulfide copper, and low in oxide copper. Oxide copper occurs predominantly in the minus 325-mesh "slimes." Microscopic examination of heavy-liquid sink products indicated that recovery of liberated copper sulfide minerals is complete in most mills, and that copper minerals not being recovered are locked with gangue particles. Additional copper could probably be recovered from most tailings by size classification, scavenger froth flotation of the coarse fraction, and regrinding of the concentrate to achieve liberation of the locked sulfides.

Jan 1, 1971

By A. B. Hooker, L. C. IlsLey

In lare-scal e blasting, it is customary to fire me.l'\Y shot.!:l simu1. taneously. The electric !atonators ara usually conneced in seies, ard are fired either from a power circuit or :from a blasting ma.chine with large capacity, operated by hand. "!hen :'::ri111; with a blasting ca.chine, trouble with missed shots has been freqi.,.ently e>:pert0nced.. Unit1:i:' thes ,:::rcu:ns tances, the shots that fail to fire are often a gr"up in the t.:E"nter r,f t>e series, Various explaz,.a.tions hs.ve been given as to the cause of the failurs. Tis paper covers a few tests made cy the electrical section of tl:.e Dti..'t'cau. cf Mines, wh;.r.;h may be helpful in understanding the -probable cuse of tl1e misfiring of c.:anter shots, Wh3tever th9 source ot the firir. current generator, magneto, or batter, the CUl"rent delivered th:·01.1.gh a shot-f:?·ing circu.it is determined by t.ae total resistance of ,;he clrcili +.; c:1nd all cure:it leaving th9 p,si tive terminal must return to tre negative te1-minal. If a. metallic circuit is well i1,.sul.:tted, praeti­ccl. l;1 a.ll of the t.'Urrent keepo within the circu.it; but in a. shot-!11·.irig ci.rc1li t, Nhere the ·.vires f:ll·e often 1n c.c,i.cact with the eru:"!ih as i11 wet holer., end whero the ins".lla.tion of the leg wires :i. inadecpa.te to prc·,ent lea.l.tage, the current ma.v tu.e v a.r ious pa the: thro-.. .. gh the nr r. earth.

Aug 1, 1922

By Sean Gallagher, Thomas G. Bobick, Diane M. Doyle-Coombs, Richard L. Unger

The U.S. Bureau of Mines has developed an in-house facility to evaluate selected effects of whole-body vibration (WBV) levels experienced by underground mobile equipment operators, Vertical vibration data were collected from a coal haulage vehicle via a uniaxial accelerometer attached to the machine frame under the operator&apos;s seat. Data were analyzed and processed so a computer-controlled platform could approximate the vibration signals. Eight men (35.5 yr 2 6.5 SD) participated in a pilot study to evaluate the effects of shock and kBV on heart rate (HR), blood pressure (BP), and subjective discomfort. Subjects were exposed to vibration for 30-min periods while seated in a typical seat (backrest angle at 90° or 130°) &apos;that was plain steel or modified with 2 in foam padding. Subjects repeated the same protocol on a separate day, without the vibration. Results indicated the vibration significantly increased the HR (Q< 0.01), systolic BP, mean BP, the number of times subjects reported discomfort, and overall subjective discomfort rating (pc 0.85). When seated in the steel seat, the overall discomfort rating (E< 0,081) ad the number of times discomfort was reported (p< 0.05) increased significantly. Seatback angle had no significant effect on any of the dependent measures.

To reduce needless paging of persons by all phones in a mine or mill, while retaining all-location page capability. Approach Standard pager phones of any manufacturer are modified to include the option of selective calling and message holding. How It Works All commercial mine pager phones presently rely upon voice paging via a loud-speaker. When a page is initiated, every phone in the system broadcasts the audible voice page, even phones in locations where the desired person could not possibly be. The advantage of this scheme is that whole-mine paging occurs. The disadvantage is that persons soon begin ignoring pages because they occur all the time, and most are for someone else. Also, it requires considerable battery power from all phones making it necessary to change batteries very frequently, even in phone locations where personnel rarely go. In addition, if a voice page is made and not heard, there Is no way to leave the message. Therefore, persons who at a later time come near a phone, have no way of knowing a page was made and was not acknowledged. This results in situations that often have a direct bearing on safety and productivity.

Jan 1, 1980

By C. W. Owings, F. E. Cash

"Transportation of explosives in mines is extremely hazardous, and where electric haulage is employed the danger is intensified. Insulated mine-car couplings have been adopted by at least five companies in Alabama and Pennsylvania - and undoubtedly in other States - to prevent an electric current passing from a mine locomotive to a car or between care joined by this coupling. The need for such protection is recognized in the report of an explosion.""Four hundred kegs of black blasting powder had been loaded into four mine cars at the railroad, to be hauled to the magazine, upgrade, by a trolley locomotive. On starting, the motorman put sand on the rail and a grounded circuit passed through the hitchings and so exploded the powder. No insulation was used between the locomotive and cars."" When used on man trips the insulated coupling further serves the purpose of guarding the men against shock. Four couplings are described so that a clearer understanding may be obtained of the details of construction.ConstructionThe general principles of construction are similar in all insulated couplings. The piece containing the hole for the coupling pin is made of steel and the steel parts are separated by an insulating material, such as fiber or wood. The coupling is either rigid or semirigid to prevent the bumpers of the mine cars from coming in contact and to keep the cars insulated from one another at all times."

Apr 1, 1928

By Bruce K. Cantrell, Stephen W. Stein, David Hassel, Harvey Patashnick

The Mine Safety and Health Administration. Department of Labor, requires coal mine operators to measure compliance with federal re¬spirable dust exposure standards periodically using approved gravi¬metric samplers. However, the gravimetric approach, with its inher¬ent delays, cannot provide dust concentration data quickly enough to allow on-site correction of inadequate dust control strategies or re¬moval of personnel from harmful environments. Furthermore, alleged tampering with dust samples collected to determine compliance with standards prompted the Secretary of Labor to appoint a special Respirable Dust Task Group to study options to improve monitoring and control of respirable coal mine dust. The Mine Safety and Health Administration&apos;s Task Group recommended that the U.S. Bureau of Mines develop a fixed-site monitor that would provide continuous information to the mine worker and mine operator regarding dust levels and the status of compliance with the applicable respirable dust standard. In response to the Mine Safety and Health Administration&apos;s request, the U.S. Bureau of Mines is investigating several sensor tech¬nologies for continuously monitoring respirable coal mine dust. One of these technologies is the Rupprecht and Patashnick Co. tapered element, oscillating microbalance. The bureau is in the process of investigating the suitability of using this sensor in the high humidity and vibration environment of underground coal mines. Laboratory tests have indicated that, with modification, the sensor can meet the humidity and vibration requirements for underground coal mine use. Currently, the bureau is developing

By Karl R. Becker

Detonators representing a sampling of various domestic commercial delay detonators were fired at various direct-current (dc) firing levels. Results of firings using well-below-recommended firing levels showed marked increases in delay times above the nominal values. There was also a marked increase in variation, to the extent that out-of-sequence firings would be essentially assured in any typical blasting round at these low firing levels. Within the range of recommended levels the effects of current increases were not considered to be of great importance relative to other overriding effects, such as the significant difference noted in average values of detonators from different lots having the same nominal delay. This effect, when combined with the normal variation noted among members from the same lot, would cause out-of-sequence firings with detonators from a neighboring delay period. Where comparisons with results from another study were possible, it was found that both studies observed quite similar variations in delay times about the average values, and a lower probability of out-of-sequence firings for the shorter delay period groups. The criterion of the previous study for assessing the likelihood of observing out-of-sequence firings, when applied to the Bureau of Mines data, properly identified two neighboring delay period groups where out-of-sequence firings would occur.

Jan 1, 1981

By G. W. Groove, E. E. Quenon

"INTRODUCTION Uncontrolled mine fires originating in exposed coal beds through the acts of careless or irresponsible persons present a serious threat to buildings, surface property, and the life and health of persons near the affected area. Apparently, the seriousness of such fires is not fully understood by property owners or those residing in the vicinity, as practically nothing has been done to alleviate conditions. In many instances, such fires have been active for several years before property owners or civic organizations have shown any interest toward having the fire extinguished. Recommendations by Bureau of Mines investigators in the interest of controlling such fires are seldom followed, as the Bureau cannot provide the funds for doing the work.Several uncontrolled and widespread fires are burning along the outcrop of coal beds and in underground abandoned mine workings within a 25-mile radius of Pittsburgh, Allegheny County, Pa. If these fires are permitted to continue to burn unabated, the ultimate results may be far-reaching. Most of the outcrop fires investigated are believed to have originated from burning rubbish, forest fires, or workmen, hunters, or others building fires near the outcrop of ,the coal beds. In other instances, smoke and fumes have suddenly appeared in the vicinity of abandoned coal-mine openings, indicating that a fire has either burned its way along the outcrop of the coal bed or has traveled through the abandoned mine from another location. An underground or outcrop coal-mine fire will be very likely to continue to burn as long as an oxygen supply is present.; and, so far as is known, such fires do not stop burning automatically until virtually all combustible matter is consumed."

Feb 1, 1948

By Dennis A. Long

"The size of off-highway trucks has increased substantially over the last decade, bringing about a radical change in truck maintenance practices and procedures. As a result, surface mine maintenance mechanics today are faced with the increased hazards of working with larger and heavier tools and components and doing repairs at greater heights, thereby exposing them to a high potential for serious injury or death. Not surprisingly, the number of accidents involving truck maintenance mechanics is significantly increasing.The Bureau of Mines has assessed the haulage truck maintenance safety problem, analyzing maintenance-accident data over the 7-yr period, 1978- 84, in terms of personnel, job activities, truck components and systems, tools involved, and truck design. This assessment, based on the review and interpretation of 1,225 haulage truck maintenance accident reports, identified major factors contributing to these accidents. Overall, young, inexperienced workers are involved in most accidents. A typical maintenance accident involves a male mechanic under 33 yr old, with less than 5 yr job experience. INTRODUCTIONOver the past decade, surface mine maintenance and repair operations have changed radically. The number of maintenance personnel has grown along with the hazards of working with larger and heavier components at greater heights and with larger and heavier tools. Furthermore, transfer of skills from over-the-road vehicle mechanics is not as feasible as it once was, because of the ever increasing size of mining equipment and the complexity of its design. In short, surf ace mine equipment maintenance and repair has become increasingly sophisticated as well as labor intensive, necessitating further research and evaluation in terms of both safety and efficiency (1, 7-8) 2"

Jan 1, 1986