Search Documents

By J. L. Konchesky

In gasifying pulverized coal with steam and oxygen, the particle size of the coal fed to a gasifier should be as small as economically possible. A potential way to achieve this advantage is to reduce the particle size of the coal by passing the coal-steam mixture at high velocity through a heated tube coil before the mixture enters the gasifier. To evaluate this method the Federal Bureau of Mines flashed coal-water slurries in externally heated metallic tube coils to determine the extent of size reduction. The first of two different laboratory-scale apparatus reduced the average particle diameter of subbituminous C coal from 190 to 110 microns at an outlet velocity of 330 feet per second (f.p.s.). At the same outlet velocity, a second apparatus reduced the average particle diameter from 250 to 140 microns. An increase in velocity produced more finely divided coal, but variation in temperature and pressure had no effect except as they affected velocity. Virtually the same size reduction was noted for five ranks of coal at equal velocities. The rate of increase in particle-size reduction with increase in velocity decreased with a decrease in particle size. The pulverizing mechanism was concluded to be abrasion of the particles with each other and with the tube wall.

Jan 1, 1961

By Stanley C. Rhoads

The Bureau of Mines investigated the complete ternary system K2 HfF6¬K2ZrF6-l.25 weight-percent HF at 40° C. In addition, solubility curves have been established at 25°, 30°, 500, 60°, and 70° C. These solubility data implemented a study of hafnium enrichment in feed solutions for liquid-liquid extraction processes.. Selected K2HfF6-K2 ZrF6-1.25 weight-percent HF mixtures were equilibrated in a constant temperature bath. Compositions of the equilibrated solutions and wet residues were established from combined hafnium and zirconium oxide and total fluorine analyses. All solubility curves were essentially parallel on triangular coordinates. At 40° C, the solid phase of the K2HfF6-K2ZrF6-1.25 percent HF system is a series of solid solution hydrates with K2HfF6-H20 and K2ZrF6.3H2O segments existing at the respective extremes. Since this system contains K2HfF6-H20 and K2ZrF6.3H20 segments, it is not ideal for simple separation of high-purity K2HfF6 from K2HfF6-K2ZrF6 mixtures by recrystallization. However, it would be useful for producing hafnium-enriched feed solutions from zircon concentrates for liquid-liquid extraction of hafnium from zirconium.

Jan 1, 1973

By W. H. Goghill

Numerous investigators have studied grinding. Each has contributed his bit to a literature that is difficult to correlate. Too many of the results have been transformed into curves with so many "inflection points" and "counterflexures" that they obscure the issue. Some of the investigators have neglected the very essence of the problem, namely the power and the amount of material to which a known amount of work was applied. The purpose of this paper is to show the ease with which results can be interpreted when these quantities are duly recognized. Some grinding tests will be given for illustration. Grinding studies are of two kinds: (1) Study of the character of the ore and (2) study of the performance of the machines. Several ores may be crushed by a given machine, or several machines may be used on a given ore. The illustrations given in this report cover both objectives.

Jan 1, 1934

By Frederick C. Tompkins

A complete service system was established for the monitoring of personnel exposure to N02 based upon the use of passive dosimetry. This system is structured such that minimum effort is required of the user: manufacturing, analysis, reporting, and record keeping functions are provided by the service organization. A field evaluation program was carried out in a dieselized mine to assess the performance of two passive dosimeters, the Walden GASBADGE TM dosimeter, and a tubular dosimeter developed at New York University. Side-by-side comparisons were carried out to evaluate dosimeter suitability for monitoring in the field, and to assess relative accuracy characteristics.

Jan 1, 1976

By Meherwan C. Irani

The Bureau of Mines is developing a new technological approach to handling the problems of fires in abandoned coal mines and waste banks. This new technology involves the accelerated combustion of "waste" coals in place (i.e., in situ) under controlled exhaust ventilation conditions, which allows for total management of the combustion products; including utilization of the heat produced" This new concept could significantly lower the costs of reducing the environmental and public safety hazards associated with waste coal fires, and could lead to the conversion of a coal waste to a coal resource. The controlled burnout technology has progressed from the laboratory stage to a full-scale field evaluation stage at the site of an abandoned-coal-mine fire. This first report describes the site selection, evaluation, and preparation, and the design and construction of the full-scale controlled burnout installation. Subsequent reports will deal with the results of the operational field trial.

Jan 1, 1983

By Robert F. Chaiken

Burnout Control is a process developed by the U.S. Bureau of Mines for accelerating the burning of wasted coal fires in situ, while at the same time controlling the heat and fumes produced. The Albright fIre project is a fIrst fIeld trial of Burnout Control as applied to a coal waste bank. An exhaust ventilation system was designed and constructed and then operated over a 1-year period at the site of an existing abandoned mine land fire near the town of Albright, WV. While predicted exhaust gas temperatures of 900° C and thermal power levels of 5 MW were achieved at 20-to 3O-in H20 vacuum levels, problems were encountered with engineering designs, equipment breakdown, and fuel-rich combustion that curtailed the time period of satisfactory operation. Effective afterburning of the exhaust gases (as they were drawn from the bank) corrected the problems associated with combustion stoichiometry and led to high thermal outputs. It is believed that with (1) improvements in engineering design and construction, (2) better control of the afterburning process, and (3) the use of conventional stack gas air-pollution controls, Burnout Control can be applied successfully to a coal waste bank fire.

Jan 1, 1991

By H. V. Makar

Laboratory tests were performed to obtain a quantitative description of the effectiveness of sodium sulfate (Na2SO4) for removing copper from molten iron and to determine the effectiveness of Na2SO4 on actual auto scrap. The tests were conducted on induction melted heats of iron averaging 0.58 and 1.50 percent initial copper and on cupola-melted auto scrap containing 0.45 percent initial copper. The Na2SO4 was added in powder form in amounts ranging from 2.9 to 43.8 percent of the weight of iron being treated. The data showed that copper removal for the various Na2SO4 treatments followed a similar trend, regardless of the iron composition that was tested. The equation Y = 1 - e-3.23x approximately reflects the relationship between copper removal and amount of Na2SO4 added, where Y is the fraction of copper removed and x is the ratio of the weight of Na2SO4 added to the weight of metal treated. Copper removals ranged from 3.3 to 74.5 percent and reductions down to less than 0.10 percent final copper were achieved in the auto scrap. Copper removals were generally accompanied by sulfur removal, and initial sulfur contents ranging from 0.10 to 0.20 percent were reduced to as low as 0.02 percent. High temperatures and long slag reaction times tended to induce copper and sulfur reversion from the slag, but, generally, the Na2SO4 treat¬ments were effective up to approximately 2,820° F with reaction times not exceeding 7 minutes.

Jan 1, 1968

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. Considerations in the mine shaft layout, design, sinking, outfitting, testing and commissioning are set forth against the background of requirements of applicable parts of Code of Federal Regulations, Title 30.

Jan 1, 1988

By Alan H. Goode

Glass wool meeting requirements for commercial use was made from glassy fractions of urban solid wastes by the Bureau of Mines. This research was a part of the Bureau's program to develop building products and other usable materials from reclaimed urban waste materials. Mixes of molten glass were fiberized into glass wool during laboratory studies by impingement of a jet of compressed air on a stream of the molten glass. The principal test variable studied was composition of the melt; this was varied by adding dolomite and alumina to obtain molten glass with the handling characteristics required for producing final wool products of the desired composition and physical characteristics. When no charge is made for the waste glass and approximately $75 per ton can be obtained for the wool product, an interest rate of return on investment after taxes of about 12 percent can be obtained. If a charge of $5 per ton is required for the waste glass, a selling price of about $78 per ton would be necessary to obtain a l2-percent-interest rate of return on investment after taxes.

Jan 1, 1972

By E. C. Perkins

As part of a program for developing methods of using domestic titanium deposits, the Bureau of Mines investigated methods for chlorinating titanium slags prepared from titaniferous minerals by electrosmelting. Titaniferous slags were made from ilmenites in the following deposits: Valley County, Idaho; Trail Ridge, Fla.; Aiken, S. C.; and Maclntyre, N. Y.; titaniferous magnetite from Iron Mountain, Wyo., were also evaluated. The tests were made in two chlorinators, a 4-inch and a 36-inch unit. Preliminary testing was done in a 40-millimeter bench-type unit. Chlorine gas was contacted with a loose mixture of titaniferous slag and carbon at a high temperature to form titanium tetrachloride. The moving-bed system used in this work involved a downward movement of feed countercurrent to the chlorine flow, and residues continuously removed from the bottom of the reactor. The performance characteristics of these slags depended on their composition, which varied widely according to the geographic source of the ore. The results showed that all but two of the slags could be chlorinated as effectively as rutile, converting 70 to 80 percent of the titanium to the tetra-, chloride. The two slags that proved difficult were made from New York ilmenite and Wyoming titaniferous magnetite. These slags contained enough magnesium to cause clinkering, which necessitated that the bed be prematurely withdrawn before more than 70 percent of it could react. The iron content of the slags did not interfere with operating the chlorinators. The data from the 4-inch and the 36-inch units were in agreement on the relative amenability of the slags to chlorination.

Jan 1, 1962

By R. H. Grau

Researchers from the National Institute for Occupational Safety and Health have demonstrated that mine-wide ventilation in large-opening stone mines can be improved by using low-pressure, high-volume propeller fans and constructing stoppings in key locations to direct and control airflow. In light of these findings, a comparative study was conducted to determine if a portable diesel-powered propeller fan could per-form more efficiently for dust dilution and transport than an axial vane fan for localized ventilation. The objective of this study is to evaluate both fan types for ventilation efficiency at an underground dump/crusher facility in a limestone mine. Results showed an improvement with the propeller fan to dilute both the respirable dust and the respirable silica dust around the dump/crusher facility. Overall, an average reduction of 20% in respirable dust and silica was observed at the dump/crusher location with the propeller fan.

By R. R. Lowery

This project was proposed to provide information on the hazards associated with arc melting of thorium. A general air-sampling analysis was made to determine the separation, concentration, and distribution of thorium daughter (decay) products throughout arc melting, machining, and forging processes of a thorium handling facility. The value of well coordinated health physics program is stressed in connection with potential health hazards and personnel protection. Building, equipment, and exhaust ventilation requirements for such a facility are discussed. Special handling methods are described for thorium. INTRODUCTION The Bureau of Mines at the Albany Metallurgy Research Center has been involved in handling the naturally radioactive metals, uranium and thorium, for several years. Cooperative work for the Atomic Energy Commission has been carried out with thorium metal, and as a result the concerned laboratories of the Center have accumulated experience on the hazards associated with this metal. This report details the radioactive hazards arising from the arc melting, machining, and forging of thorium.

Jan 1, 1962

By Mark I. Copeland

This study was conducted by the Bureau of Mines to determine the effect of steel reheating practices in burning natural gas on the amount of silicon required to prevent the formation of copper on steels containing up to 1 wt-pct Cu. Formation of copper, which causes surface hot shortness, was readily prevented by as little as 0.3 wt-pct Si and by 2 vol-pct excess oxygen in the furnace atmosphere when reheating steels containing up to 0.8 wt-pct Cu. Up to 0.8 wt-pct Si content and careful control of reheating conditions were necessary for steels containing 1 wt-pct Cu. Best conditions for these steels were reheating to 2,200° F (1,205° C) in burning gases containing 2 vol-pct excess oxygen, and then to higher temperatures in gases of 6 vol-pct excess oxygen. Slag and mold wash were not detrimental on steels reheated for 8 hr by a soaking-pit-type furnace schedule, but they were problematical on steels heated for 2 hr by a pusher-type furnace schedule. The effect of silicon contents on scaling rates also was determined.

Jan 1, 1974

By Wils L. Cooley

Several aspects of coal mine safety-ground system operation are studied. Evaluations of two sophisticated ground-wire monitors are presented, along with a detailed report of development work on a modular ground-wire monitor. A portion of the report covers stray current flow in the safety-ground system, analyzing in detail conditions surrounding the generation of both dc and ac ground wire current. Considerable detail is provided concerning studies of mine ground beds. Additional progress is reported in the development of a. continuous ground-bed monitor, and new techniques are developed for the design of ground beds and their resistance measurement. New methods of accurately measuring electrical parameters of finite layered conducting structures are also reported. The effects of stray currents in ground beds is included. Touch-and step-potentials associated with mining equipment are analyzed, and methods are presented for determining earth voltage gradients around structures contacting earth. Instrumentation to determine gradients easily is suggested. Finally, an extensive effort is described dealing with lightning transients on open-pit coal mine ground systems. The nature of the transients, their expected frequency of occurrence, and the ways in which they damage equipment are analyzed in detail.

Jan 1, 1977

By R. Mark, R. Richards

The Washington National Cathedral is one of the largest masonry structures in the USA, and like many of its European Gothic counterparts, it required nearly a century to construct. The design was altered during this period, resulting in greater loadings than were originally anticipated on the soil beneath the foundation. When signs of continuing differential settlement were observed in the early 1990's, the Cathedral approached the US Bureau of Mines (now the National Institute for Occupational Safety and Health (NIOSH)) for assistance in monitoring the movements of the massive towers and walls. An array of dual-axis tiltmeters was installed about 40m above ground level to measure wall and tower inclination, with the data sent over a dedicated phone line to the NIOSH Pittsburgh Research Laboratory for processing. Mechanical gages and string-potentiometers are also being used to measure motion across cracks and joints, and differential pier settlement is being monitored with optical-level surveying. Data have now been collected for almost 7 years, and they show a long-term settlement trend masked by dramatic diurnal and seasonal thermal movements. The paper discusses the major findings of the study, implications for the future of the Cathedral, and conclusions regarding the use of geotechnical monitoring at major national monuments.

By H. J. Heinen

This Bureau of Mines report reviews the recent developments in the heap leaching of gold ores with dilute cyanide solutions and the recovery of gold and associated silver from the pregnant effluents by a carbon adsorption-desorption method. Mineralogical considerations, experimental work, field studies, and commercial operations are described. Also presented are recent process advances developed by the Bureau, including the application of (1) alcohol additives to the conventional hot alkaline cyanide strip solution to enhance gold desorption from precious metal-laden activated carbon, and (2) Na2S precipitation of the silver from geld-silver cyanide solutions as a means of reducing the inventory of carbon required for precious-metal adsorption from heap leach effluents and for the production of low-silver bullion from activated carbon stripping solutions.

Jan 1, 1978

By A. G. Starliper

The Bureau of Mines made laboratory investigations to determine the feasibility of utilizing fine tungsten wires to reinforce a number of nonferrous metals and alloys and a superalloy, S-8l6. The composites of tungsten filament and metals were chosen to attain elevated temperature strength and corrosion resistance. Oriented clean or precoated tungsten wires were incorporated with the other metals by extrusion, swaging, and infiltration casting. Although widely varying characteristics were found in the composites, none were considered satisfactory for high-temperature use, chiefly because of reactions between the matrix metal-tungsten surface. Diffusion, solution, and chemical reactions between matrix and tungsten wires were sufficiently slow for some combinations, such as 15 v/o 8-816, to exhibit increased high-temperature strength for a limited time. A few metals failed to wet or bond to the tungsten surfaces, while a few responded after precoating with a third metal.

Jan 1, 1968

By M. J. Sapko

A moderately scaled apparatus was developed by the Bureau of Mines to determine the fire resistance characteristics of mine conveyor belts and similar type materials. The design of the apparatus was based upon data obtained in full-scale fire tests and features a radiant panel to preheat the belt and a methane-oxygen ribbon burner to ignite the sample under ventilating condi¬tions in a rectangular duct. The test method overcomes the limitations of existing laboratory-scale methods and provides a measure of both ignitability and flammability in quantitative terms. Flame propagation depended upon such variables as air velocity, ignitor heat flux, and belt width and height in the test chamber. Data are presented for nine belt materials and fire resistance ratings are proposed in terms of the flame spread rate, heat release rate, and the critical ignitor heat flux. The ratings discriminate between the fire hazard posed by different fire-resistant belts and tend to be in reasonable agreement with those obtained in full-scale fire tests.

Jan 1, 1981

By Leonard Obert

This report presents evidence indicating that when rock is stress-relieved during the course of mining or in drilling a core, it may be altered or damaged to the extent that the physical properties of the relieved specimen are not the same as those of the in situ rock. Furthermore, this type of damage may result from stress change other than that accompanying stress relief, such as the application of a relatively large compressive stress. In some instances the damage is microscopic, manifesting itself as incipient cracks or the failure of individual crystal bonds. However, if the sample is taken from a high-stress area, macroscopic damage may occur.

Jan 1, 1962

By Ned Baker

Details are given of a fuel-induction system for a hydrogen, fueled engine. The induction system was designed to preclude backfire otherwise common in hydrogen fueled engines. System features and test data are presented and discussed in the context of the requirements peculiar to use in an underground mine environment. The fuel induction-system when tested in conjunction with a modified Caterpillar 3304 engine provided backfire free engine operation and satisfactory engine performance.

Jan 1, 1982