Search Documents

By Mark Dangerfield

[Power-Point Presentation]

Jan 1, 2005

By K. Moxham, A. Smit, R. Pickering

Since the early 1970s research has been ongoing to develop a cost-effective way of continuously mining the narrow reef, hard rock, typical of South African gold and platinum mines. In the late1980s it was shown that impact ripping was a practical solution for the deep gold mines. In March2001 Lonmin and Sandvik agreed to co-operate in an endeavour to design and manufacture a prototype narrow reef mining machine with the ultimate aim of producing such a machine on a commercial basis that would enable Lonmin to create a safer and more productive environment within its mines and for Sandvik to enhance its leading position as a supplier of a new generation hard rock cutting machine. This paper describes the developed technology, the current progress of the delivery of the required objectives and the optimum mining layout for the roll-out of the mining method.

Jan 1, 2006

By N. Moemise, M. B. Shongwe, P. A. Olubambi, M. M. Ramakokovhu

"Near-infrared (NIR) spectroscopy sorting technology is incorporated in an automated optical mineral sorter that can discriminate between materials using the differences in characteristics when exposed to near-infrared radiation. During September 2014 to April 2015, a pilot plant that utilized NIR technology to discriminate between kimberlite and waste materials was commissioned to determine the viability of including this technology in the diamond winning process flow sheet at Cullinan Diamond Mine. The plant was used to minimize the waste content in the size fraction -70+35 mm that reports to the crushing section and then to the dense media separation process. This paper describes the initial test work, conducted at Mintek, that led to the decision to conduct a pilot-scale study. The mineralogical characterization of the feed and product streams to establish the sorting criteria and the operational data obtained during the pilot plant campaign are described. The results indicated a good possibility of discriminating between the kimberlite and waste material using NIR technology. However, the consistency of discrimination was not good enough to avoid the risk of potential diamond loss. Furthermore, a lower than expected availability of the machine reduced the throughput capabilities. IntroductionUsing near-infrared spectroscopy (NIRS) technology for ore sorting is a new concept for the mineral processing and mining industry. NIRS has been used for decades in the laboratory for the identification of pure minerals, and has its roots in the recycling, food, and pharmaceutical industries (Salter and Wyatt, 1991; Robben et al., 2009). Ore sorting in itself is not a new concept; it was introduced during the Stone Age with handsorting being the first method to separate valuable materials from gangue (Wills and Napier-Munn, 2006; Sassos, 1985). However, over the years the scale of mining has increased and hand-sorting has become challenging to implement (Joensson, 2014).Sensor-based sorting is an advanced technology that can help overcome problems such as ore dilution experienced in mineral processing operations. The benefits are lower energy and water costs, reduced ore dilution, lower environmental impact, and improved profit margin (Mathew, 1974; Jonsson, 2014; Salter and Wyatt, 2009; Death et al., 2009). In sensor-based sorting, materials are mechanically sorted based on certain physical properties that are detected by a sensor (Dalm, 2013). Research has found that with NIR scanners it is possible to obtain a ‘fingerprint’ of a sample that is directly related to its mineralogical composition. According to Woutruba et al. (2009), molecules absorb NIR radiation by means of electronic and vibrational transitions. Nowadays, there are many sensors available in the market that utilize different material properties; the choice of a sensor is dependent on the mineralogy of the ore."

Jan 1, 2016

By C. Cunningham

The process of initiating opencast blasts through long cables is onerous. An obvious alternative is to replace these with radio controlled firing apparatus. Such devices appear from time to time and with the advance of telecommunications, more are likely to appear. However, there are two crucial and seemingly intractable obstacles to overcome: firstly, the problem of malfunction of the system, which can either fire prematurely or go into a state of suspense in which it is unknown whether firing might unexpectedly occur, and secondly, the problem of terrorism, as such a system could provide the capability for an off the shelf remote bomb. The issues of accessibility and electronic reliability when linked to explosives in a mining environment have to be demonstrated to be adequately covered before serious consideration should be given to these systems, up to now largely confined to military applications.

Jan 1, 2003

A Special General Meeting of the Institute was held in Kelvin House, Johannesburg on Wednesday, 29th September, 1971. The President, Prof. D. D. Howat opened the meeting at 9.55 a.m. The President read the notice of meeting which was as follows: "In order to bring industry into closer liaison with the work of your Institute and to place the Institute's finances on a sound basis your Council recommends that companies be admitted to membership of the Institute under clause 2.6 of the Constitution, that is, as Non-Corporate members. The designation for this class of member will be that of "Company Affiliate". 2 Membership: This clause to be amended as follows:- 2.6 "Non-Corporate members shall comprise the grades of:- Company Affiliate Honorary Fellow Graduate Associate Student" 2.6.1 This clause to be added:- "Companies involved in or associated with the mining or metallurgical industries are eligible to become company affiliates" 2.14 Add:- "A special certificate shall be issued to all company affiliates". After giving the background to the recommendation made by Council the President asked for a proposer and seconder for the resolution. Mr J. K. E. Douglas proposed and Mr D. G. Maxwell seconded the resolution. The meeting agreed that the constitution be amended as proposed. The meeting closed as 10.05 a.m.

By D. V. J. W. Groenewald, T. M. Louw, L. Auret, S. M. Bradshaw, A. V. Cherkaev

Unexpected equipment failures lead to financial losses due to production disruption. Time-based maintenance, based on checks over regular time periods, has been employed to minimise disruption. However, the improvements it can offer are limited as it may lead to unnecessary service of healthy equipment or missed failures occurring between service intervals. Condition-based maintenance (CBM) provides a further improvement to equipment reliability by detecting faults and predicting remaining useful life (RUL) based on equipment health monitoring. Its application in the mineral processing industry is hindered due to the high cost of health monitoring equipment. In this study, two stochastic process models, the adaptive auto-regressive model and the gamma process, are compared in their ability to forecast the degradation state and to provide RUL prediction. The gamma process model was found to be effective in both tasks. Due to its simplicity and minimum hyperparameters requirements, it is proposed to use the gamma process as a baseline for comparison with other models. Keywords: Condition-based maintenance, remaining useful life, slurry pump, adaptive autoregressive mode, gamma process

Jan 1, 2020

By L. L. Godirilwe, and A. Shibayama, G. Danha, K. Haga, Y. Takasaki

Selective extraction through leaching of an amorphous slag obtained from a base metal smelter plant in Botswana is investigated in this paper, where the main objective is to optimise the experimental variables that would result in the maximum selective extraction of the three base metals (Ni, Cu and Co) from the slag waste. Mineralogical tests showed that the sample is composed mainly of fayalite (Fe2SiO4), with a total entrapped metal sulphides content of about 1.0 wt.% occurring as fine occlusions in the fayalite phase. In our experimental program, we compare the effectiveness of two common leaching techniques. In the first method, we use sulphuric acid to carry out atmospheric beaker leaching tests, and in the second method we use high pressure oxidative leaching. The effects of acid concentration, oxidant addition/oxygen partial pressure and pulp density on metal dissolution rate are examined. The optimal Ni, Cu, Co extractions of 80.5%, 81.9 and 98% respectively were obtained under high pressure oxidative leaching conditions (150 oC, 0.6 M H2SO4, 0.5 MPa O2), with substantially low dissolved Fe of 9.6%, the majority of which was removed as jarosite in the residue. Atmospheric beaker leaching yielded poor extractions of Ni below 40% when sulphuric acid combined with hydrogen peroxide (1.0 M and 0.6 M respectively, 65 oC) were used for leaching, while Fe, Cu and Co dissolutions were each about 80%. Therefore, using high pressure oxidative leaching provides a possibility to effectively extract Ni, Cu and Co while producing an environmentally benign residue, thus alleviating the current adverse environmental issues associated with the abandoned smelter slag. Keywords: Slag, amorphous, fayalite, atmospheric beaker leaching, high-pressure oxidative leaching, extraction

Jan 1, 2020

By G. M. Evans, S. Mitra, G. J. Jameson, M. M. Hoque, E. Doroodchi, R. Moreno-Atanasio

In this study, the detachment behaviour of 314 μm diameter silica particles from a single 3 mm diameter bubble rotating in a confined cavity connected to a cross-flowing water channel was investigated. The liquid cross-flow generated a rotating flow inside the confined cavity, which was quantified using 2D particle image velocimetry (PIV) measurements. The fluctuating (x-y) velocity components inside the cavity for each cross-flow velocity, U, were then used to estimate the corresponding time/volume average turbulence intensity values, Ti. Turbulence intensity ranged from 9.3-16.2%. In the absence of a bubble, the rotating vortex within the cavity created a pressure field which decreased towards the centre of the vortex; wherein the lowest pressure zone was located at the centre of the cavity. The vorticity into the cavity was found to increase with increasing the turbulence intensity. A bubble, both without and with particles attached, was introduced into the cavity under different flow conditions and its motion was tracked using the shadowgraphy technique. Experimentally, it was found that the bubble-particle aggregate was trapped at the centre of the cavity (low-pressure region) following a spiral trajectory. An interface resolved 3D computational fluid dynamics (CFD) model was developed to predict the particle detachment conditions within the confined cavity. CFDpredicted vorticity in the absence of a bubble agreed well with experimental observation. The CFD analysis indicated that the vorticity inside the cavity was not significantly changed when a single bubble was introduced. On this basis, the computed vorticity was utilised in describing the force balance applied to the attached particle. Computationally, it was found that the critical turbulence intensity, beyond which the particle was detached from the bubble, was 14%. This value was consistent with the experimental observation of detachment at Ti at 15.7%, and above, but not at lower values. Keywords: Bubble, particle, turbulence intensity, vorticity, particle detachment, CFD, PIV

Jan 1, 2020

Zincor operates four Lurgi fluidized-bed roasters at its roast-leach-electrowin refinery in Springs, South Africa. In 2006, Zincor?s four roasters had reached ages ranging between 26 and 38 years, while the expected life of this type of roaster is generally 20 to 25 years. Roaster 3 was the first to be rebuilt in 2006 because its condition had deteriorated the most. Roaster 4 is being rebuilt in 2007 and the last two roasters will be rebuilt over the next few years as necessary. The main damage to Roaster 3 was caused by buckling of the roaster steel shell. This caused the freeboard and dome areas to shift, resulting in cracks in the dome brick lining and crumbling of the bricks lining the freeboard. The steel shell buckled owing to the combined effects of excessively high operating temperatures and corrosion. These were caused by the following two main factors: ?Thicker external insulation was installed during a previous maintenance shut, which resulted in an increased steel shell temperature and exacerbated the normal metal fatigue ?SO2/SO3 containing gas that had permeated the brick lining passed through its dew point during frequent planned and unplanned shuts over the life of the roaster. This caused acid formation between the refractory brick lining and steel shell, resulting in corrosion of the shell. The initial plan was to replace only the damaged areas of Roaster 3, but when it was dismantled more damage was found, and the roaster was rebuilding from the tuyeres upwards. During there building the opportunity was taken to modify the design of some of the brickwork to extend its life and make future repairs easier. This paper discusses the mode of failure of Roaster 3 and the lessons learnt during its dismantling and rebuilding.

Jan 1, 2007

By E. Garab, M. Pillalamarry, E. Develo

"Recent geological exploration at Rosh Pinah mine revealed that the mine’s major production is shifting towards the western orefield, which will increase the demand for air flow to be supplied to this area. A snapshot of the ventilation survey carried out in December 2014 at the western orefield drill drive B (WOF-DDRB) showed that the air flow was well below the required standards. In order to improve the existing conditions, possible options were considered and simulated using Ventsim™ software.The best option found was to replace the existing western orefield fans with the larger fans from the inactive southern orefield workings, to increase the air flow in the DDRB district. Simulation showed that as much as 20 m3/s of air can be received at the working faces of WOF 30, compared to the previously received amount of 1.37 m3/s. The economic analysis indicated that the above option can reduce the ventilation cost by N$1.9 million annually. It was also noticed that after implementing this option together with other projects, the ventilation conditions in the mine were greatly improved and currently give no cause for concern. IntroductionA good mine ventilation system should be capable of providing adequate quantity and quality of air to all working faces, and is critical to the occupational health, safety, and comfort of underground employees (Luxbacher and Ramani, 1977; Exikis and Kapageridis, 2006). No ventilation system can remain adequate indefinitely; as the mine workings are extended, the ventilation characteristics such as system pressures, air volumes, leakages, and airway resistances change considerably. Continuous improvement of the ventilation system is needed to ensure compliance with health and safety regulations (Lovejoy, 2010). It also ensures that the right quality and quantity of air is delivered to all the necessary areas at the lowest possible cost. This can be achieved by identifying inefficient airways and poorly ventilated areas in the mine and planning how best to upgrade them.The latest geological exploration shows that the focus of production at Rosh Pinah mine is shifting towards the western orefield (WOF). As mining progressed, the working areas have advanced away from the main fans, which increased the resistance to air flow drastically and resulted in increasing demands being imposed on the main fan in order to supply an adequate air flow. This process also created more leakage paths between the fan and the working areas, which has caused the air to short-circuit before it can reach the faces. Consequently, a much larger quantity of air has to be circulated by the fan so that the stipulated quantity reaches the face, which increases operating costs (Singh et al., 2004)."

Jan 1, 2016

By J. Sepulveda

"Despite the recognized influence of product fineness on line capacity and downstream process performance, few mineral concentrators today use particle size measurement of the final product in automatic control applications for particle size. ‘Near-line’ particle size instrumentation has existed for decades and is utilized in modern concentrators, but low availability and measurement frequency, due to problems with slurry sampling and transport systems, make these technologies unreliable for use in automatic control. An innovative technology for real-time particle size measurement on individual hydrocyclones, named CYCLONEtrac™ PST (particle size tracking), has been developed by CiDRA Minerals Processing, and proven in commercial installations, demonstrating near 100% availability with minimal maintenance requirements, thus overcoming the limitations of previous technologies. Potential stakeholders require convincing, reliable information regarding the economic value delivered by automatic grind control projects. In this paper we present a methodology for estimating such value with the CYCLONEtrac™ PST technology, and demonstrate unique opportunities to improve process stability and performance. Based on actual plant data accumulated over time, the evaluation approach assesses and highlights the significant potential process improvement that can be expected with the particle size tracking technology. As an extension of previous work, in this paper we present the key operating criteria for optimizing the production of valuable metals and increase mill throughput by identifying the optimal grind size. As this requires operating closer to the process boundaries, accurate real-time particle size measurements, such as those provided by the CYCLONEtrac™ PST system, become essential for achieving the maximum potential value from every operation. For further illustration, data from three different copper plants is compared.Introduction Owners and operators of mineral concentrators constantly search for the most economically attractive way to increase the output of valuable metal. A logical approach is to identify a key parameter that has the greatest impact on the performance of multiple stages of the process and then use a holistic analysis methodology to determine how this key parameter can be controlled to optimize the final output.Particle size is widely recognized as such a key parameter; however, very few concentrators today use real-time particle size measurements for automatic control of the final product size due, to a large extent, to the inherent limitations of existing technologies. ‘Near-line’ particle size measurement instrumentation, which has been used for decades, typically suffers from low availability because the fundamental measurement technologies were developed for other, less demanding industries and then adapted to the harsh environment of the typical mineral concentration process. An outline of the key differences among the available technologies used for particle size measurement in comminution circuits has been completed in previous work, and plant data has proven the benefits of measurements on individual cyclones – something that, until now, has not been possible (Cirulis, 2017)."

Nov 1, 2018

By R. Pipeleers

Recent experience has shown that all underground workplaces in the Campine Coalfield in Belgium will require controlled cooling within three years. Considering the socio-economic and legal importance of the climatic problems underground, IREA has undertaken studies in forecasting the climate of future workplaces, planning the necessary cooling equipment and optimizing efficiency in the existing cooling equipment. These studies are being carried out using the climate forecasting program of Bergbau-Forschung. So far, the German model has been obliged to utilize manually measured data from a few workplaces in the Campine. As the model does not fit very well with these measurements, it has been thought necessary to' develop a system of continuous data acquisition and transmission. This system is being tested in the Beringen mine of the N.V. Kempense Steenkollenmijnen. In the first part of this paper the digital tranmission system is described; in the second the sensors used to collect the necessary climatic data are presented, and in the third some results are given.

Jan 1, 1987

The first annual student prizegiving function of the South African Institute of Mining and Metallurgy was held in the Dorothy Susskind Auditorium, University of the Witwatersrand, on Thursday, 26th May, 1977. The address (see opposite page) was given by Dr M. G. Atmore, a director of Anglo American Corporation and Vice-President of the Institute.

Jan 1, 1977

By F. W. Petersen

The Conference Minerals & Materials '96 was held in Somerset West, South Africa, from 31st July to 2nd August, 1996. It was organized by the Universities of Stellenbosch and Cape Town, the Cape Technikon, and the Western Cape Branch of The South African institute of Mining and Metallurgy (SAIMM). The three-day Conference was attended by 180 delegates, representing countries such as Australia, South Africa, United Kingdom, Finland, Sweden, Germany, Poland, Zambia, and Zimbabwe. The programme and associated exhibition were well organized, and each of the delegates received two volumes of proceedings containing the 77 papers presented at the Conference.

Jan 1, 1996

By M. Buchmann, T. Mütze, F. Heinicke

Dry air classification is a well-known technique used for decades in the cement industry to separate material in the size range of 0.01-1.0 mm. Additionally, in corresponding dry grinding circuits with effective machines such as High Pressure Grinding Rolls (HPGR), the energy consumption can be reduced compared to wet applications. These dry systems are not state of the art in minerals processing plants, but first prototypes have been installed and an increasing number of projects are starting to evaluate this option. One challenge in this field is the mineral composition of ores, which have, by far, a higher variety in density and size than those of cement. High density particles such as iron- containing ones have higher settling rates than low density silica particles of the same size. The main question to answer in this paper is how to evaluate this effect, so a quantitative method using Mineral Liberation Analyses was developed to calculate two-dimensional partition curves. Additional statistical analyses allow for isolation and quantifying the interaction of density and size, enabling engineers to consider this effect for the sizing of process plants. The paper will present the method and selective results for a compounded ore of iron and silica. Keywords: HPGR, air classification, partition curve, MLA

Jan 1, 2020

By C. Aldı, O. Yaral

For the more economical excavation of tunnels in underground mining activities, the selection of mechanised excavation machines (such as roadheaders, electro-hydraulic drills, etc.) and the analysis of performance prediction that can be used in estimating machine energy consumption have been subjects of research from past to present. One of the parameters to be considered in studies examining these methods, is the grinding process. The success of increasing efficiency in grinding is expressed by a reduction in energy consumption. The goal of a grinding process is to maximise the grinding amount at the appropriate grinding size while minimising the energy consumption per tonne of the fragmented material. Today, the depletion of high-grade ore deposits has largely directed the mining industry towards low-grade but large reserve ore deposits. This shift has particularly increased the importance of the grinding process, as it is dependent on particle liberation. Grinding is a critical step in reducing the mineral to the appropriate size, and energy consumption poses a significant challenge in this process. As a result, researchers have conducted various studies focusing on energy efficiency and cost optimisation in this field. In this study, the grindability of 7 different coal environment rocks (sandstone, siltstone) from the Zonguldak Basin, Uzulmez Region was investigated. For this, Hardgrove Grindability Index and Bond Work Index tests were conducted. While determining the relationships between grindability and other parameters, the results obtained from the Hardgrove Grindability Index (HGI) test were used. The energy values found in the Bond Work Index (BWI) test were used to evaluate the excavatability of the rocks. Additionally, tests for strength, hardness, drillability, and abrasiveness were conducted to observe the impact of other parameters on grindability. Considering the results obtained from the experiments, significant relationships were found between the grindability of the rocks and other parameters.

Mar 30, 2026

The utilization of computer assisted tomography (CT or CAT-scan)as general non-destructive examination (NDE) technique and as research tool for scientists in South Africa, is limited due to the relative unavailability or nonexistence of such specialized analytical equipment. Many medical hospitals are equipped with X-ray CT scanners for the diagnostic examination of patients but do not easily allow paleontologist or other scientist to utilize their very expensive equipment. As from 2003, Necsa hosts the South African Neutron Radiography (SANRAD) and tomography facility where neutrons from the SAFARI-1 nuclear research reactor and their penetrating power as well as X-rays as a complementing tool, are utilized in many R&D applications. This facility is being made available to HEI and specifically utilized by postgraduate students as part of their studies and/or by industry on an ad hoc commercial basis. The capability of these radiation imaging facilities at Necsa will be demonstrated in areas such as paleontology, geosciences and specifically the physical properties of rock and the distribution of minerals in borehole cores, petrophysics to predict the percentage tar/oil/water content within sandstone samples and others. The penetration capability of neutrons through specimens with a matrix of high atomic number (dense materials) and their ability to be attenuated by low atomic number material (light density) makes neutron imaging complementary to X-ray imaging. The capability of X-ray and gamma radiation for relatively easy penetration through specimens of low atomic number allows for viewing of imbedded high atomic number materials and density variation. X-ray micro focus radiography is capable of resolving objects of micro scale size that are micro distances apart whereas X-ray phase contrast radiography utilizes the wave properties of the electromagnetic spectrum of X-rays to clearly define edges of the specimen under investigation. Many applications with neutrons as imaging probe are successfully applied at several facilities across the globe such as at NIST in USA, Neutra at PSI in Switzerland, and ANTARES at FRM2 in Germany, etc, are documented 4?9, through world conferences on neutron radiography, for example. This is achieved through very well thought through and implemented instrumentation from the production of neutrons to their detection and interpretation of the images. The need arose at Necsa to upgrade the current facility from 42-year-old technology, which was successfully applied in neutron imaging over the past 10 years, to state-of-the-art technology found at European facilities. This initiative started under the auspices of an IAEA-TC programme for the period 2007?2010.

Jan 1, 2008

By W. Newcomen, G. Dick

"Effective management and mitigation of pit slope instability in open pit mines begins with a comprehensive slope monitoring programme. The ability to differentiate between non-critical pit wall movements due to rebound or relaxation of the excavated slopes and movements that may be indicative of slope failure is important for maintaining a safe working environment and maximizing production. Slope failure prediction methods using velocity, acceleration, and strain criteria have been introduced and put into practice over the past few decades. Forty-eight slope failures with surface monitoring data are presented and assessed using the strain-based failure prediction approach, with consideration of the quality of the rock mass and the potential failure mechanism. The results indicate that the strain-based approach can be used to provide general guidance regarding strain thresholds for pit walls for a variety of failure modes in diverse geological environments. The advantages and potential drawbacks of the strain-based and other slope failure prediction methods are discussed. The importance of implementing a pit slope monitoring and performance evaluation system early in mine development is also emphasized. IntroductionThe successful prediction of the Manefay Slide pit slope failure at Bingham Canyon at 9:30 am on 10 April 2013 (Engineering and Mining Journal, 2014) highlighted the importance of having a comprehensive slope monitoring system that provides an accurate prediction of the time of failure of an open pit slope. Using most of the geotechnical monitoring tools available, the time of the failure was predicted within hours and equipment and personnel were evacuated from the pit well in advance of the failure. From a time to slope failure perspective, the monitoring system in place was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities. was a success.There are two general groups interested in monitoring pit walls, with slightly different objectives in mind when the monitoring system is being set up. There are those at the mine site that have to implement the pit slope design, monitoring protocols, and the action response plans, and there are those designing the slopes (often consultants) who regularly visit the mine but may not be responsible for the day-to-day activities."

Jan 1, 2016

By L. Chanderman, C. E. Dohm

"Mineral Resource estimation (MRE) and classification are highly dependent on the confidence in the model of the orebody geometry, known as the geological model, within which the estimates are constrained. An understanding of the geology of a deposit is thus fundamental to the Mineral Resource evaluation process. The geological model is a function of the structural and depositional complexity of the geology captured by drilling information, which is limited in the early stages of a project. The information effect has a significant impact in terms of the interpretation of the geology as well as the estimation of grade continuity and the resultant risk associated with the Mineral Resource estimate and classification.Therefore, as new drilling information becomes available, it is necessary to update and refine the geological model to appropriately constrain the resource estimates. The grade information is also updated, including statistics and the spatial correlation characteristics. This refinement is based on geological interpretations derived from the drillhole information that becomes available throughout the life of the mine; orebody knowledge that comes from working experience of the deposit, as well as familiarity with the software package used for modelling, is also important.In updating, the potential to identify new resources in previously unknown areas may be realized. The opposite may also occur where previous interpretations of ore continuity are refuted. Both scenarios could result from a better understanding of the geology of the deposit and thus a more realistic MRE, which reduces geological risk. This paper describes how newly drilled advanced grade-control holes for a gold deposit in Mali were used to refine the 3D geological model for the deposit in an attempt to identify the potential for additional oxide ore using conventional geostatistical evaluation techniques."

Jan 1, 2017

By A. N. Brown

The Hendrik van der Bijl Memorial Lecture is arranged annually under the auspices of the Pretoria Engineers Liaison Committee. This is a multidisciplinary Committee with representatives from eleven societies and associations, and serves the interests of engineers resident in the Pretoria area. Coal preparation The Japanese Organizing Committee of the 11th International Coal Preparation Congress is now busy making the necessary arrangements for the Congress, which is to be held in Tokyo from 22nd to 26th October, 1990.

Jan 1, 1989