Search Documents

By B. T. McKenna, H. Nirschl, P. Morsch, B. Fränkle

Generally, filter media used in filter presses have a limited operational life. Besides mechanical damage, there is a growing deposition of fine particles with increasing filtration cycles, the so-called blinding, inside the filter cloth. The resulting decreasing pore diameters not only affect the efficiency of the filtration process itself by increasing the filter medium resistance, but also make it more difficult to regenerate the filter press between the individual cycles, e.g. leading to an insufficient cake discharge. Since tailings filtration requires handling of large process flows containing a significant fraction of particles in the lower micrometer range, an investigation into media rejuvenation is of interest. Keywords: Tailings filtration, filter fabric resistance, filter media regeneration, filter cleaning, intraweave contamination

Jan 1, 2020

By M. J. Deats

INTRODUCTION To prepare the reader adequately, reference should be made to the paper 'The Pioneering of Fully Mechanized Longwall Coal Mining in South Africa' by R. T. Naude and M. J. Deats, published in the February, 1967, edition of the Journal. At the time mechanized longwalling had been proved operationally feasible with encouraging results since its inception in South Africa in mid 1965. Subsequently, further top seam panels were successfully extracted with improved productivity and with some modification to equipment. In 1968, after an overseas visit by mine officials, equipment specific to suit local conditions was acquired and lower seam trials commenced. Despite initial obstacles and difficulties the first panel was successfully mined. Modification and improvements to equipment and techniques resulted in the second lower seam panel being extracted economically during 1969-1970 and with productivity exceeding even that of top seam faces. During extraction of the second lower seam panel, gradual and complete surface subsidence occurred over the panel without affecting face operations. Rock mechanics investigations had originally indicated some uncertainty regarding adverse dolerite sill behaviour which could have caused longwall mining to be hazardous. All such doubts have now been removed. RESUMÉ AS AT FEBRUARY, 1967 Mechanized longwalling was introduced in 1965 on an experimental basis in an effort to improve productivity in the newer area of the mine and to increase the quality of the comparatively dirty run of mine feed to the washing plant. In addition advantages could be predicted in the long term by better utilizing reserves of straight coking coal and increasing the life of the mine. The top seam unit was obtained on a rental basis and by the beginning of 1967, two panels, the first having a face length of 215 m, a panel length of 345 m, seam section of 1 219 mm, and the second the same face length, a panel length of 453 m and a seam section of 1 067 mm had been successfully longwalled. At this stage a best month of 24 602 metric tons with an average of 17 364 metric tons per full working month could be reported. Results were sufficiently encouraging for the company to exercise its right to acquire the equipment as its own asset and from 1967 onward, the unit has operated on this basis. From the point of view of rock mechanics, the dolerite sill over the first two panels was known to have 'bridged', only the material below the base of the sill having truly 'goafed'. No adverse pressure effects had significantly affected face operations except for two 'bumps' towards the end of operations in each panel. Gate road maintenance presented no problem. The strong inflows of water experienced on the first face were now known to be associated with an isolated water bearing fault plane and were not experienced on the second face. TOP SEAM EXPERIENCE - MAY, 1966, TO DATE Panel 2 (February, 1966, to November, 1966) The operations in panel 2 (see Fig. 1 for location of panels) continued uneventfully until the final month in this panel. At this stage, the chocks behaved most inconsistently often lowering under the weight of the canopies alone. Roof trouble became so severe that the unit was unable to produce adequately and blasting of chocks became a daily occurrence. Finally 24 m short of the planned limit it was decided that a complete overhaul was the only solution and the extraction operations commenced. At this time, the only fatal accident associated with longwalling occurred when a Non-White inadvertently fell into the panzer conveyor transfer point at the main gate. Some gate road difficulties in this panel were overcome by bolting tapes to the roof as decking and allowing them to pass over the gate chocks and collapse into the goaf. Two cribbed roof falls were also negotiated by the gate chocks at the face ends without undue difficulties. It was decided in the light of maintenance problems encountered on this face that the best solution would be to appoint a foreman solely in charge of face maintenance crews. This step has to a large extent contributed to success achieved subsequently. Panel 2-face length 213 m panel length 456 m cutting height 1 092 mm average monthly output 16 443 t best month 19 130 t Panel 3 (December, 1966, to June, 1967) By the end of 1966 results were sufficiently encouraging for the company to exercise its right to acquire the equipment. This was negotiated and the unit has operated as such to the present date. Prior to installation in panel 3, all face equipment was thoroughly overhauled underground and the chocks boost-tested to yield-load. The costs of overhauling, including almost complete hose replacement, were much higher than anticipated. Advice had been received that complete hose replacement was common practice after +/- 18 months' operation. Shortly after commencement of operations in panel 3 the chocks again failed as they had towards the end of panel 2. At this stage, the suppliers advised that the valve gear should have been repaired during the overhaul as the needle and seat seals could no longer be relied upon. This operation was impossible to carry out on the face and would have been e1ttremely time consuming. Fortunately a new type of valve gear was then available from the suppliers, termed the capsule-type valve, and a complete change over could be made on the face. The encapsulated valve has a delrin pad sealing over a raised

By V. Miguel-Silva, B. C. Afonseca

Drill-hole spacing analysis (DHSA) and optimization are becoming commonplace for uncertainty assessment and management in the mining industry. However, there is no standardized DHSA workflow, and the outputs of certain methodologies are not interchangeable. We group available simulation-based DHSA methods according to their accounted uncertainty into (i) raw uncertainty, assessed by drawing realizations from synthetic data-sets with the drilling spacings to be tested; and (ii) model uncertainty, in which these synthetic data-sets are used to assess the variation between the estimated model and the (unknown) actual value. DHSA workflows available in the literature ignore the differences between both types of uncertainty. Commonly, the DHSA algorithm is chosen without a detailed analysis of its uncertainty output, which may lead to misleading results and suboptimal decisions. While available solutions are based only on assessing raw or model uncertainty, the proposed approach simultaneously analyses both and their relationship for models at different stages of the mine. The integrated analysis results deliver more information to support decision-making than available methods. Principles, practical considerations, and discussions of the advantages of the proposed integrated analysis are presented. The approach is applied to a real gold deposit to illustrate its use.

Jun 2, 2022

By N. Hadebe, A. Mampuru, F. Jantjies

Mintek conducted test work to study the effect of media wear when using Mintek’s Milling-in-raffinate technology. The grinding media consisted of high-chrome and ceramic balls. The tests were conducted using a laboratory 5L 316 stainless-steel rubber-lined mill. Magotteaux supplied the high-chrome and ceramic balls. The raffinate was synthetically prepared using a typical Cu/Co (2.2 g/L Cu, 3 g/L Co) composition. The milling rate, media wear, mill, leach extraction efficiencies, gangue acid consumption, and residence time were studied. The tests indicated that the high-chrome balls had a higher corrosion rate than the ceramic balls. The ceramic corrosion rate was lower than 0.1 mm/y. The highchrome balls performed better during the leach stages with faster milling time, higher leaching efficiencies for both Cu and Co, lower gangue-acid consumption, and lower residence time

Jan 1, 2023

By F. Ntuli, T. V. Nyangadzayi

Chromium green is an essential metal with various applications in the paints, construction, electronics, and aerospace industries. The main source of chromium green is the carbo-thermic reduction of chromite ores, however, chromite ores are being heavily depleted on a global scale, hence the need to find alternative or secondary sources for the chromium. In order to meet the global demand for chromium there is a need to implement principles of the sustainable circular economy to keep chromium within the material loop. Ferrochrome slag and stainless steel slags are secondary resources that are potential sources of chromium. In this work, recovery of chromium from ferrochrome slag was investigated. The ferrochrome slag was alkaline leached using sodium hydroxide- sodium hypochlorite solution to reduce the use of potent reagents that have a potential negative environmental impact. The leachate produced by oxidative alkaline leaching of ferrochrome slag contained hexavalent chromium, which was used to recover the extracted chromium through a two-stage process involving reduction and precipitation. Reduction of hexavalent Cr to trivalent Cr was investigated using anhydrous FeSO4 at concentrations of 5 g/L, 10 g/L, and 15 g/L. Precipitation was conducted by dosing the reduced leach solution with 1 M sodium hydroxide at dosages of 5 ml/L, 10 ml/L, and 15 ml/L. The experiments were designed using the Taguchi (L9) orthogonal array and analysed according to the ANOVA, general linear model. The optimized conditions for the reduction step were ferrous sulfate dosage of 5 g/L with a pH of 12, and for the precipitation step, 1 M sodium hydroxide at a dosage of 15 ml/L with a setting time of 90 minutes and pH of 7. Physical changes were observed during the two-step chromium recovery, with solution changing from a yellowish colour to dark green colour indicating completion of the reaction. The chromium recovery was found to be 93.3%.

Dec 11, 2024

By Z. Zhang, J. Niu, H. Wang, Y. Xu, J. Shi

Tribo-electrostatic separation is a promising method for effectively utiliing low-grade magnesite resources by removing quartz and improving the grade of magnesite. To determine the chargeto- mass ratios of pure magnesite and quartz, a triboelectric measurement system was employed, and a laboratory tribo-electrostatic separation system was used to separate low-grade magnesite. The results showed that the maximum difference in charge-to-mass ratio between pure magnesite and quartz particles was observed after friction with polyvinyl chloride. The grade and recovery of magnesite increased with temperature and initially increased with increasing voltage, feed rate, and air flowrate before gradually decreasing. The optimal conditions resulted in a concentrate with 46.91% MgO content and 77.36% recovery, while the quartz content decreased from 7.02% to 1.95%. These experimental results demonstrate the effectiveness and potential of tribo-electrostatic separation in removing quartz and upgrading magnesite.

Apr 14, 2024

By V. Quezada, Á. Astudillo, L. Valásquez, M. Garcia

Seawater has become a viable alternative for different uses in copper hydrometallurgy. In this paper we review the main physical and chemical characteristics of seawater and how these influence copper production. Reliable data on the use of continental water are reported, and the current use and consumption of seawater in the Chilean mining industry is analysed, indicating the main areas of use and the main problems encountered. Additionally, the influence of the elements in seawaterthat have the most influence on the extractive metallurgy of copper are considered. The Chilean copper mining industry currently consumes approximately 4.1 m3/s of seawater, which corresponds to 25% of the total water used. The use of seawater for the leaching of copper sulphide minerals, such as chalcopyrite, is beneficial because it provides 20 g/L of chloride, thereby improving copper dissolution kinetics.

Jul 5, 2023

By T. C. Maswanganyi, G. L. Smith, R. C. A. Minnitt

This paper identifies the strategic gaps and opportunities for the South African mining industry’s contribution towards advancing sustainable development. Mineral resources companies are confronted by a range of complex social performance challenges, which largely manifest in sporadic community and labour unrest, undermining the sustainability and profitability of these companies. Integrating supply chain management, strategic long-term planning and sustainability planning is identified as a strategic gap that can contribute towards the sustainability of mining companies, if effectively implemented. Contributing towards sustainable development by the South African mining industry is not merely a voluntary requirement on the industry but a legal requirement in terms of the Minerals and Petroleum Resources Development Act No. 28 of 2002. This Act is legislation aimed at advancing socioeconomic development in communities that host mining operations and in areas that provide labour to the South African mining industry. In contributing towards the advancement of sustainable development in mining host communities, not only will mining companies fulfil a legal requirement in terms of the Minerals and Petroleum Resources Development Act, but they will also prevent negative social and economic impacts in those communities. This paper identifies innovative and cost-effective ways of advancing sustainable development by integrating strategic supply chain management, strategic long-term planning, and sustainability planning.

Dec 15, 2025

By E. Maritz

"The localized uniform conditioning (LUC) technique was proposed by Marat Abzalov in 2006. The technique converts conventional uniform conditioning (UC) grade-tonnage curves into single grade values attached to each smallest mining unit (SMU). This is achieved by ranking the SMUs within a panel in increasing order of their grade (based on the direct kriging of SMUs). This ranking is then used to localize the conventional UC grade-tonnage curves for each panel by dividing them into classes and computing their mean grades, which are assigned to the SMUs. The quality of this localization process will depend heavily on the validity of the grade patterns predicted by the direct kriging of the SMUs. Abzalov noted that where the distribution of data available for the direct kriging of the SMU is characterized by strong short-range variability, the advantages of using the LUC approach may be more limited. Consequently, a study was undertaken to determine how valid the predicted grade patterns of a typical Birimian-style gold deposit (with high nugget effect and strong short-range variability) might be expected to be. This was determined by comparing the direct SMU kriging ranking (based on sparse data) with the grade control model ranking (based on close-spaced data and the best available estimate of the deposit). The results showed a satisfactory correlation between these rankings and it was concluded that, although the grade patterns predicted by the direct kriging of the SMUs may be less meaningful for deposits exhibiting strong short-range continuity, there is nevertheless a convincing relationship with the actual (or best available) rankings. Therefore, the LUC technique is still considered to be useful for this style of deposit. IntroductionFor adequate technical and financial evaluation of a project, attempts should be made to estimate the recoverable resources – the portion of the in situ resource that can be economically extracted by mining. To achieve this, the estimates of the tonnage and grade of the mineralization should be produced above a given economic cut-off and should take into consideration the proposed mining selectivity."

Jan 1, 2016

By C. B. Espag de Klerk, J. de Goede, M. Le Roux, Q. P. Campbell

"Excessive amounts of moisture in product coal can influence the efficiency of downstream utilization processes due to a decreased calorific value and handling problems. Stockpiles can be used to decrease the moisture content of coal by means of gravity drainage and evaporation. This paper is focused on the evaporation of moisture from a coal stockpile surface with the aim of investigating the effect of particle size on the rate of evaporation as well as the depth to which evaporation extends.It was observed that moisture initially evaporates at a higher rate from a stockpile consisting of fine particles (-6.7 mm) than from coarser particles (-13.2 mm +6.7 mm). This high rate of evaporation is restricted to the outer shell of the fine coal stockpile. However, for coarse coal, the porous nature increases the depth at which evaporation occurs. Evaporation of moisture was observed up to the fourth day of each experimental run, after which steady state was obtained. It was shown the water can evaporate from the surface into the body of the stockpile, depending on the coal particle size and void spacing. An experimental reclaim depth of 0.4 m was achieved after 4 days. IntroductionCoal stockpiles serve as surge capacity for downstream utilization processes and can also be used for moisture reduction by means of gravity drainage and evaporation. Excessive amounts of moisture in coal can cause handling problems and, most importantly, will decrease the calorific value, leading to inefficient combustion.Research has shown that evaporation by means of wind and solar action is considerably more effective than gravity drainage(Williams, D.J. 2006), but the effect is limited to a restricted depth from the exterior of the stockpile (Boyapati, E. and Oates, A. 1994; CSEM-UAE, 2010). The effectiveness of wind and solar action can be improved by orienting the stockpile perpendicular to the predominant wind direction, maximizing the surface area of the pile, and reclaiming the coal from the pile gradually in shallow cuts over a large area (Williams, D.J. 2006)."

Jan 1, 2016

By M. Z. Emad, Y. Majeed, G. Rehman

Massive deposits of rock salt are mined in the Salt Range area of Pakistan. The main export products of rock salt include salt lamps, blocks, and tiles, while local consumption includes the chemical industry and domestic use. The profitable production of salt for value addition depends on the quality, size, and shape of the block. Salt processing for value addition is easier when very few cracks are present in the blocks. The current salt mining practice involves drilling and blasting, which introduces undesired fractures in the material. This paper focuses on the extraction of rock salt blocks by applying conventional cuboidshaped block mining methods used in quarries. The techniques include wedges and feathers, expansion chemicals, and blasting with low-yield explosives. Experimental work involved both laboratory-scale and in-situ field testing. Laboratory experiments assisted with the determination of splitting force, loaddeformation curves, and other rock mechanics parameters. Regression analysis proposes a relationship for the estimation of radial strain from the load in the case of the wedges and feathers method. The splitting force obtained from the laboratory tests was used to confirm the accuracy of the already published empirical relationship. The results of the laboratory as well as in-situ tests showed that the wedges and feathers technique is the most suitable method for mining rock salt blocks of the desired size, shape, while minimizing cracking.

Mar 2, 2022

By S. J. Thomas, P. A. Lilly

With support from the Australian mining industry and the Federal Government, three Australian universities are collaboratively developing flexible-format, web-based course content and delivery in rock mechanics for undergraduate mining engineering students. This paper describes the educational philosophy behind the development and summarises other salient features of the Program. Mit der Unterstuetzung von der austlalischer Bergbauindustrie und der Bundesregierung, drei austlalische Universtaeten in Zusammenarbeit entwickeln flexibel Netzgengruendet auf Lehrganginhalt und Lieferung in Felsgestein fuer Bergbaustudenten. Dieses Schreiben erlautert das Unterrichtsphilosophie hinter der Entwicklung und Zusammenfassung anderer Hauptpunkte von diesem Programm" Avec l'assistance de l'industrie miniere australienne et du gouvernement federal , 3 universites Australiennes collaborent a la mise en place d'un programme de mecanique des sols pour etudiants- ingenieurs en mines. Ce programme serait a la fois flexible et accessible par Internet. Ce document decrit la philosophie pedagogique de ce projet et en souligne les characteres importants.

Jan 1, 2003

By P. Ramsaywok, G. Legodi

Spiral concentrators are widely used in the coal industry treating fine (-1mm) coal. Their application was a limitation to the product quality until the introduction of low-cut spirals which allow a lower quality ash product to be produced, thus expanding the market. The Exxaro Grootegeluk 1 (GG1) plant has a two-stage traditional rougher-cleaner spiral circuit using conventional SX4 spirals to produce semi-soft coking coal product at 12.5% ash by mass. The overall plant product is 10.3% ash meaning that the coarser sized coal dense medium separation circuits must compensate. A low density cut-point spiral targetting 10.3% ash would thus be beneficial to the overall complex. The spirals were tested in the two-stage plant environment and in a pilot plant. This paper discusses the findings and compares a two stage four-turn low density cut and conventional spiral. The two spiral technologies were unable to sustain a 10.3% ash product. Pilot test work was also conducted on GG1 coal, demonstrating that an eight-turn low density cut-point spiral achieves the targetted 10.3% ash under controlled conditions. Keywords: Spiral, low-cut, coal

Jan 1, 2020

By J. Du, V. Shukla, C. R. Kumar, U. Shivangi, D. P. Chakraborty

During the processing of iron ores, a large quantity of low-grade tailings containing abundant iron values in fine particle size range is produced. Due to the increasing demand in the high-grade ores for metallurgical operations and the stringent environmental conditions imposed on mining activity, it is essential to utilise the waste tailing pond slimes. Recovery of iron values from these tailing ponds not only enhances the life of the existing operating mines, but also enables achievement of a sustainable process. Iron ore tailing/slime (-150 μm) is produced after scrubbing and wet screening of a low-grade iron ore. Tailing beneficiation of iron ore has been addressed either by flotation or wet high intensity high gradient separation. The present paper aims to recover iron values from discarded slime containing assay ~56% Fe, ~6.5% SiO2, and ~7.0% Al2O3 from the Noamundi processing plant by using a high gradient magnetic separator (HGMS). In this process, tailings are effectively processed with a vertical pulsating high gradient magnetic separator to produce a relatively high-grade iron concentrate. The results of investigation indicate that this novel process is capable of producing an iron concentrate assaying ~ 60% Fe and ~3.25% alumina with a yield of ~55 % on weight basis and recover > 65 % iron bearing particles from the tailings. More importantly, the corresponding tailing contained ~45% Fe. It was concluded that this novel process may be effectively used to recover iron values from low-grade hematite tailings. Keywords: Iron ore slime, Fe recovery, HGMS, yield, Noamundi

Jan 1, 2020

By O. A. Olaseinde

The 2101 lean duplex stainless steel has wide potential application in storage, heat exchangers, and in the oil and gas industries. This work investigates the electrochemical behaviour of 2101 duplex stainless steel with an addition of 0.15 wt% ruthenium, using potentiodynamic techniques in 1M H2SO4 at 25º, 40º, 60º, and 80ºC. The microstructures of samples were characterized using optical metallography and scanning electron microscopy. The results showed that the ruthenium addition moved the corrosion potential of alloy 2101 to a more positive potential. All samples containing ruthenium displayed longer passive regions at 25°C and 80°C compared to those without ruthenium. Alloys without ruthenium had higher critical current density (icrit) values when compared to the alloys with ruthenium. Ruthenium additions decreased the passive current densities and inhibited anodic dissolution. At room temperature the corrosion rate of alloys with ruthenium was lower than these without ruthenium.

Jan 1, 2012

By R. J. Quevedo, Y. A. Sari, S. D. McKinnon

The large scale of cave mines leads to many challenges, including operational logistics and geomechanics design. In current practice, pillar stability assessment relies almost exclusively on stress analysis. However, stability is also affected by other factors including those related to operational aspects of the mining method, the effects of which are difficult to account for during the design stages. In this paper we present a case study of the application of a machine learning approach to evaluate the influence of these operational factors on pillar stability at the Chuquicamata underground cave mine in northern Chile. Due to the likely multi-factorial damage process leading to collapses and considering the different pillar conditions, a tree-based machine learning method was used and analysed to improve the understanding of the relative importance of the various contributing factors. Unlike stress analysis methods, it does not require any a priori knowledge of failure mechanisms, nor the calibration of associated controlling parameters. The proposed random forest model predicted pillar collapses with 80% accuracy despite limited samples to model from. The main contributing factors to collapses were found to be related to available pillar volume, cave front geometry, and time under abutment stress conditions. The effects and interactions of such factors were also studied, showing that careful and improved control over operational conditions can significantly reduce the likelihood of pillar collapses. These conclusions could not have been obtained from stress analysis alone, illustrating the complementary nature of conventional stress analysis and machine learning approaches.

Mar 14, 2024

By M. Ataei, F. Sereshki, R. N. Masir

Given the inherent risks and disruptions in underground coal mining operations, strengthening the resilience of critical infrastructure has become a vital priority. This paper aims to evaluate the resilience of the underground coal mining environment using historical data and expert judgment. The study serves as a framework for optimising the utilisation of critical infrastructure to minimise operational disturbances. To achieve this, a practical methodology has been developed, incorporating nearly two and a half years of collected operational data, a hierarchical structure, and a systematic approach. Furthermore, a case study is conducted to demonstrate the real-world applicability of the proposed method. Finally, the resilience index isintroduced as a straightforward summation of ranked impact factors, providing a clear metric for resilience assessment.

Dec 15, 2025

By C. M. D. Majola, K. E. Langerman

Energy efficiency is a cost-effective way of both bolstering energy security and limiting the harmful effects of energy use on the environment. Mining is an inherently energy-intensive activity, and the 2008 revision of South Africa’s National Energy Efficiency Strategy (NEES) set a target of a 10% reduction in energy consumption by 2015 for the mining sector. In this study, we investigate the effectiveness of the NEES in improving energy efficiency in the South African coal mining sector by surveying energy intensity at a number of operations, and analysing energy efficiency trends and energy use by process and energy carrier at an underground coal mine in Mpumalanga. Most mines surveyed exhibit an increase in energy intensity over time. At the case study mine, the increase was primarily due to increased energy use in the beneficiation and discard reclaiming processes. Trends in energy consumption are a poor reflection of trends in energy intensity, as a decline in energy consumption is most easily achieved by reducing production. A more appropriate metric for energy efficiency at coal mines is energy intensity, defined as energy use per unit of saleable product, relative to a multi-year baseline. The evidence suggests that the NEES has been ineffective in promoting energy efficiency in South African coal mines. We propose that greater success could be achieved by monitoring and reporting on energy intensity at the process level, and by incentivizing energy efficiency gains.

Sep 6, 2023

By G. Akdogan, J. H. Zietsman, C. Dorfling, D. Attah-Kyei

The development of newer and improved electrical products has led to an increase in the rate at which older products are discarded as waste. The main focus of electronic waste is the printed circuit board (PCB) because of the inherently high value of contained metals such as gold and copper. Several options for treatment of the non-metallic fraction including material recycling, where the residue may be used as inclusions in concrete or asphalt materials with minimal processing or chemical recycling, where chemicals and fuels are produced from the residue using pyrolysis exist. In this paper, the utilisation of the non-metallic leached PCB waste fraction as reductant in secondary copper smelting was investigated. Analysis of the leached residue revealed that PCB is highly amorphous and has a carbon content of 28.5%, an oxygen content of 23.1%, with the ash and volatile matter contents 40.1% and 44.8% respectively. Thermodynamic simulations of secondary smelting of copper were conducted in terms of metal recovery, and the energy required when PCB was used as a reductant. The results were also compared with that of coal and PCB-coal blends. The simulations revealed that as PCB in the blend used as reductants increases, the amount of energy required for the smelting operation decreases. Metal recovery slightly decreased as the mass percent of PCB in the blend increased due to lower carbon content present in PCB relative to coal. The results also highlighted the energy saving with PCB-coal blends which was around 160 kWh per ton of feed relative to coal. The decrease in the amount of energy required for the operation is attributed to the higher volatile content of the PCB, which is also a part of the reduction process. Keywords: PCB leach residue, alternative reducing agent, secondary copper smelting

Jan 1, 2020

By N. Nišić, A. Cvjetić, V. Jovanović, D. Knežević, D. Nišić

The risks associated with operating water reservoirs and tailings storage facilities (TSFs) are different because of their different purposes, methods of construction and operation, and characteristics of the materials impounded and their flow behaviour. Regardless of the differences, these two types of structures are often put in the same category when it comes to risk assessment and the application of relevant methodologies, which may result in unrealistic outcomes. In this paper we investigate whether it is possible to apply the risk ranking methodology designed for water reservoirs to TDFs and overview the key differences between these two types of structures. We also provide a comparative analysis of the results obtained by conducting a risk assessment of the operation of a TSF, applying the method recommended by the International Commission on Large Dams (ICOLD), and analyse the results using the failure mode and effects analysis (FMEA) technique. It is concluded that a more realistic evaluation of risk levels can be obtained by adopting a systematic approach to risk assessment in accordance with the traditional risk definition on which the FMEA technique is based.

Nov 30, 2022