Search Documents

By A. F. Silva, R. Dockendorff, J. M. Girao Sotomayor, V. F. Navarro Torres, C. Castro

This paper shows the importance of performing probabilistic analyses in open pits, especially for mine planning, which can lead to more efficient ore extraction and meeting the acceptability criteria for safety in mine slopes. Three-dimensional stability analyses were performed to evaluate the future geometry of a large open pit for iron ore extraction in Brazil. The strength parameters of the lithologies were calibrated using ruptures in the pit walls. After determining the factors of safety (FoSs) from the calibrated parameters, probabilistic analyses were performed using the total range of values of each parameter under different field conditions to verify the reliability of the initial analysis. In this sense, it was possible to plot the probability of failure (PoF) and the FoS on the graph of slope height versus slope interramp angle (IRA) for the future pit in each lithology. IRA recommendations are made for two scenarios: (1) the best scenario: dry without ubiquitous joints and (2) the worst scenario: the water table at 10 m depth with ubiquitous joints in the most unfavourable direction. The results show that probabilistic evaluation is an important tool for establishing alert mechanisms in slopes that can be termed stable.

Jul 2, 2022

By J. N. Van der Merwe

"Platinum is a highly valuable resource, its safe and economic extraction is paramount. The success of platinum mining by the bord and pillar method depends heavily on a comprehensive and dependable pillar design method. Pillars need to be large enough to safely support the load and small enough to avoid loss of resources. A critical evaluation of current pillar design systems used in narrow-reef platinum mining was undertaken using practical experience from a large feasibility-stage platinum exploration project, supplemented by observations from several platinum mines in Zimbabwe. An extensive literature survey was undertaken in order to determine the current status of design systems. Through this approach, the shortcomings of current pillar design systems are highlighted. Areas are proposed for further research to obtain a better understanding on how additional factors influence pillar system stability. The exploration work highlighted how rock mass classification methods can be utilized in determining the overall strength of pillars. Current pillar design systems for narrow-reef platinum mining consider width-to-heightratio (usually with different exponents for width and height) and the strength of the pillar material. However, there are many more important factors that are not considered and which have a bearing on pillar system stability. An in-depth study of these parameters with a view to establish effective narrow- reef platinum mining pillar design systems needs to be undertaken. IntroductionPillars have been used as a means of support since the early days of mining. Pillarsupported mining methods such as bord and pillar require a reliable design system for them to be successful. This paper presents an evaluation of the current hard-rock mining pillar design systems as applied to a practical large-scale narrow-reef platinum mining feasibility study. It is vital to have a dependable pillar design system for economic and sustainable mining. Using an extensive database collected from the project, the pillar strength formulae were tested and several discrepancies noted. This necessitates the establishment of more reliable pillar design systems. In narrow-reef platinum mining, large compressive stresses accompanied by geological and geotechnical factors contribute to pillar instability. A well-formulated pillar design system is required that accounts for such factors so as to minimize pillar failures."

Jan 1, 2017

By I. V. Filippova, Y. Foucaud, M. Badawi, L. O. Filippov, S. Lebègue

To optimize the flotation of Ca-minerals, their separation contrasts were investigated by coupling experimental and theoretical techniques. We showed that they mainly rely on structural properties such as the Ca-Ca distance on their exposed surfaces but also on the ability to control the intermolecular interactions. An optimized composition of the carboxylic collector by calculating the collector-mineral and the intermolecular interactions was developed. Blending the saturated acids and non-ionic molecules with a fatty acid collector significantly increases the flotation selectivity between scheelite (CaWO4) and fluorite (CaF2). The theoretical results were validated by experimentally improving the separation contrast between Ca-minerals. After the tests of several depressants and collectors, the best depression of gangue Ca-minerals (fluorite, apatite and vezuvianite) was found by combining sodium silicate and sodium carbonate. Keywords: Ca Minerals, Fluorite, Scheelite, Carboxylic acids, Unsaturated Acid, Fatty acids

Jan 1, 2020

By V. V. Getman, V. A. Chanturiya, T. N. Matveeva

Most of the Au and PGM ores in Russia are characterised by a thin mineral impregnation of noble metals in sulfide minerals, and a large variety of mineral forms that lead to high loss of precious metals with fine fractions during flotation. In modern flotation technology, the rational choice of reagents is one of the main trends for selective separation of minerals and effective metals recovery. New data on the selectivity of the thermo-sensitive polymer with specific functional groups (TMPPh) as a flocculant and collector of Au and Pt fine fractions are available. The selective modified collector (DEDTCm) for the recovery of Au and Pt from complex ores is discussed in this paper. Scanning electronic microscopy (SEAM), laser SIM and AFM microscopy, UV and IR spectroscopy were applied to study the adsorbed layer of new reagents on the mineral surface. Flotation tests of TMPPh on the gold-bearing ore of the Olimpiada deposit showed an increase in Au extraction and Au content in the concentrate of the rougher flotation. Using a combination of reagents TMPPh and ButX, the quality of the Au and Pt concentrates increased in 1.7 time with an increase in recovery up to 15 % compared with the traditional reagent mode. Testing of TMPPh polymers in flotation of Pt-Cu-Ni ore at Norilsk Nickel has shown the ability to obtain a concentrate with a higher Pt content. Recovery of platinum is 17% higher than recovery in an experiment without polymer. Application of DEDTCm helped to achieve higher technological parameters in flotation of lowgrade Rt-Cu-Ni ore. Compared to the basic mode Pt recovery was plus 13%, Pd recovery was plus 9% and the content of precious metals in the rougher flotation concentrate increased in 2,5 - 4 times. The studies have been supported by Grants of the President of RF “Scientific School of Academician V.A. Chanturiya” NSh-220.2012.5, NSh-748.2014.5. Keywords: Au and Pt complex ores, flotation, flocculation, thermo-sensitive polymer TMPPh, modified collector

Jan 1, 2020

By D Olivier

De Beers' Finsch Mine is situated in the Northern Cape province, 170 km northwest of Kimberley. The concentrator facility, designed and constructed by Bateman Engineering, was commissioned in 1967 and upgraded in 1979 using diamond liberation and extraction technology available at the time of design. Since then significant advances in diamond processing and technology have been made and these -have been incorporated into the new main treatment plant and recovery plant flowsheets, making diamond liberation and recovery from the Pre-1979 dumps a viable economic option at Finsch."

Jan 1, 2010

By D. K. Chibwe, P. Taskinen

"Typical operation of industrial Peirce-Smith converters (PSCs) used in copper smelting results in several common phenomena such as excessive splashing, slopping, tuyere blockage, and low converter campaign life due to high tuyere line refractory erosion. These phenomena give rise to an inefficient operation from both a process and an energy perspective.This investigation presents numerical and physical models of flow patterns, mixing, solid-liquid mass transfer, and slag-matte phase distribution in a slice model of an industrial PSC. For physical simulations, a 0.2-scale cold model was developed. Water, kerosene, air, and sintered benzoic acid compacts were used to simulate matte, slag, injected gas, and solid additions into the PSC. The two- and three-dimensional numerical simulations of the three-phase system were carried out using volume of fluid (VOF) and realizable k- e (RKE) turbulence models to account for the multiphase and turbulence nature of the flow respectively. These models were implemented using the commercial computational fluid dynamics numerical code FLUENT.Both numerical and physical simulations were able to predict, in agreement, the mixing and dispersion characteristics of the system in relation to various blowing conditions employed in the investigation. Measurement of mass transfer characteristics conclusively indicated that fluid flow in the PSC is stratified. Both blowing configuration and volume of slag in the converters were found to have significant effects on mixing propagation, wave formation, and splashing.The splashing and wave motion in these converters are known to cause losses of metal/matte and potential production time due to the requirement for intermittent cleaning of the converter mouth, resulting in reduced process throughput. To prevent these losses and hence to increase process efficiency, we propose a combined blowing configuration using top lance and lateral nozzles. The numerical simulations were conducted on combined, as well as lateral, blowing conditions. In comparison, the recent results of the combined blowing concept were found to be encouraging."

Jan 1, 2014

By F. S. Hoseinian, B. Rezai, E. Kowsari, M. Safari

In order to remove heavy metal ions from a large volume of wastewater with a low ion concentration, ion flotation appears to be promisingly effective. In the ion flotation process, because of the high ion removal percentage, the amount of water recovery percentage is a very important factor which determines the process efficiency. However, ion flotation suffers from relatively high collector concentration to achieve the high removal percentage to the desired limit, which subsequently increases the water recovery. In this study, functionalised graphene oxide (FGO) was synthesised, using a chemical method in the ion flotation process, applied as a collector for increasing process efficiency by reducing the collector consumption and water recovery. The high ion removal was achieved with both collectors of sodium dodecyl sulfate (SDS) and FGO, while the water recovery with a collector of SDS was 3.4% higher than that with a collector of FGO. The results indicated that the FGO could be effectively used for high ion removal and low water recovery in the ion flotation process. Keywords: Ion flotation, synthesised collector, ion removal, wastewater, water recovery

Jan 1, 2020

By D. Hu, J. Xu, N. Liao, C. Wu, J. Ye

The vertical stirring mill’s fine grinding equipment is affected by the operating conditions during the grinding process. The grinding media has a great influence on the energy consumption and particle size distribution. This paper investigates the fine grinding performance of nano-ceramic balls and steel balls of the same weight for magnetite by a wet grinding process in a vertical stirring mill, where 15 mm nano-ceramic balls and 12 mm steel balls are used as grinding media to carry out batch grinding tests. We have observed that the newly qualified particle content of the nano-ceramic balls is higher than steel balls of the same weight at the same specific energy. The reason may be the advantage of a greater surface area and volume filling rate with the nano-ceramic balls. Moreover, the specific energy of nanoceramic balls is less than steel balls of the same weight under the same grinding fineness. In addition, energy efficiency indicates that the nano-ceramic ball has a higher energy efficiency than a steel ball of the same weight. This is due to the light bulk density of nano-ceramic balls. The application of a nanoceramic ball in a vertical stirring mill will improve iron ore grinding performance. Keywords: Steel balls, nano-ceramic balls, vertical stirring mills, fine grinding, particle size distribution, energy consumption

Jan 1, 2020

By G. Sánchez, S. Seiler, B. Klein, T. Cebeci, P. Bradshaw

The Decar Nickel District is a greenfield discovery by FPX Nickel Corp., of nickel mineralisation located in central British Columbia (BC), Canada. The Baptiste deposit is part of the Decar Nickel District and is a unique deposit containing a nickel-iron alloy mineral called awaruite, with over 2-billion tonnes of inferred resource grading 0.12% Davis Tube Recoverable (DTR) nickel. This deposit represents a significant nickel resource. Awaruite is a high density and ferromagnetic mineral, which could be recovered, along with magnetite that is also present in the samples, using magnetic separation. However, there is still a lack of understanding of the properties of the awaruite and its metallurgical response. This information is imperative for the set-up of the variables involved in its concentration. The aim of this paper is to show and discuss the effect of magnetic field strength for the recovery of nickel from Baptiste deposit samples. Magnetic separation at bench and pilot scale with different magnetic field strengths is evaluated as a concentration method for awaruite. Mineralogical information is provided to support the results and also to briefly assess the variability of DTR nickel within the deposit. The Baptiste deposit is unique and will benefit from a sound scientific understanding of the process solution as well as other ongoing work. If successful, the outcome will lead to the development of a mine. With greater than 2-billion tonnes of inferred resource, the mine would represent a significant new source of nickel globally. Keywords: Nickel ore processing, magnetic separation , awaruite, magnetite

Jan 1, 2020

By S. Banisi, A. Ghasemi, A. Fazeli, M. Rezaei, M. Maleki-Moghaddam

The efficiency of high capacity SAG mills which consume large amounts of energy depends on the grinding and slurry discharge systems. A 9.7 m × 4.8 m SAG mill with radial pulp lifters is used at the Sarcheshmeh copper complex grinding circuit. The process audit indicated that the pulp discharge system was not efficient, judging by the amount of slurry flow back and carry over. These events limited the discharge rate and increased the wear rate of the lifters and grates. With the objective of finding a new design for pulp lifters, a 3D DEM software (KMPCDEM ©), along with the plant operational data and photographic evidence was used. The KMPCDEM © software was used to compare the efficiency of the radial and curved pulp lifter design based on the material flow. The slurry flow was analysed in terms of ease of discharge and lifter wear rate. It was found that changing the radial pulp lifters to curved pulp lifters could improve the discharge efficiency,and decrease wear rate of the pulp lifter in particular at the base of the pulp lifters. The simulation results showed that if curved lifters with a radius of 0.3×mill radius are used, the amount of slurry flow back and carry over will be negligible. It is predicted that by installing the curved pulp lifters, the capacity of the mill increases by 10% and the pulp lifter service life improves by at least 20%. Keywords: SAG mill, radial pulp lifter, DEM,curved pulp lifter, Sarcheshmeh

Jan 1, 2020

By X. Cao, R. Wang, H. Han, Y. Hu, Z. Wei, W. Sun, H. Tang, J. Wang

Flotation reagents play a vital role in mineral flotation. In the past century, most studies focused on the modification of anion or cation collectors and the synergistic effect of mixed collectors, which have contributed to research. In this study, we reviewed brand-new reagents, metal-organic/inorganic complexes, with the functional group of metal ion, which are totally different from the traditional anion or cation collector and show absolute specificity for some minerals. For example, Pb-BHA complex collector was developed to realise the atmospheric flotation of scheelite due to the absolute specificity for calcium minerals. Calcium oleate collector was found to be the effective species in the flotation of calcium minerals, and has been employed to selectively separate fluorite from calcite. Selective adsorption of Al-Na2SiO3 polymer on calcite surfaces proved the self-assembly of H2SiO3 polymer using Al3+ had stronger selectively adsorption ability than Na2SiO3. Also that Fe3+-starch complex was a better depressant for iron minerals than caustic starch and contributed to a more efficient reverse flotation. In conclusion, metal ions are good templates for molecular assembly and can be used to control the structure of metal complexes and exhibit special properties, which provide possibilities for the design of new flotation agents. Keywords: Metal-organic/inorganic; flotation; collector; depressant

Jan 1, 2020

By P. van der Steen

This paper examines the historical developments in diamond beneficiation technology and the impacts on the industry. The art of diamond beneficiation has given way to the application of scientific process, but at considerable capital expenditure. The shift in beneficiation methodologies has been disruptive to the traditional skills set of the industry, but evolutionary change continues and has been beneficial to the quality of the final product.

Jan 1, 2010

By M. Kumral, S. Li, M. Balci, Z. Shao

Main haulage roads play an important role in the performance of underground mines because of the cost of transportation of the extracted ore, equipment, and workers. During mine development, these roads are designed through manual tools or CAD-based software. However, the optimisation of these roads is still a complex problem due to some constraints such as minimum turning radius and maximum gradient. By utilising Dubins path theory, three elevation cases; namely low, medium and high are defined, considering gradient constraint as well as the minimum turning radius in a three-dimensional space. The shortest path between two points can then be found by the three-dimensional Dubins path algorithm with elevation constraint. As a further step, a three-dimensional Dubins path algorithm with elevation constraint for multiple points is also developed for multi-point cases. The effectiveness of these algorithms is tested through case studies in order to determine the optimal path between different points.

Sep 1, 2021

By G. de Tomi, G. C. Teodoro, E. Rodovalho, T. M. El Hajj, J. A. S. Tenório

The selection of an underground mining method stems from a multivariate analysis that considers geomechanical, geological, economic, and operational parameters. Even after identifying the most compatible method, there is no assurance that the mining company will achieve the best performance. The geological complexity of some deposits requires adaptations of methods described in the literature to obtain more selectivity and reduce mining waste. There are some studies on geometry of underground structures, but a methodology that describes an adaptation of a room-and-pillar mining method for ore bodies with down-dip varying from 20° to 25° is novel. The present work aimed to reduce dilution by adapting the traditional room-and-pillar mining method (TRP) to inclined ore bodies. This new method is entitled short-hole room-and-pillar (SHRP). The equations that measure the dilution are defined according to the geometry of stopes and openings. The results comprise comparative analyses of the operational and planned dilutions to measure the performance of the SHRP method. The average operating dilution of the SHRP method was more than five times lower than the planned dilution according to the TRP method. Low operational dilution indicates high selectivity of the method and its potential to reduce underground mining tailings.

Sep 9, 2024

1. Book review . Australasian coal mining practice, edited by C.H. Martin. Reviewer: R.B. MacGilIivray This book is an extremely comprehensive coverage of coal-mining practice in Australasia, the countries covered being Australia, New Zealand,and Papua New Guinea. 2. From The Institute of Metals The folowing are available from The Institute of Metals, 1 Carlton House Terace, London SWl Y 5DB. Physical and elastic characterisation, edited by M. McLean. 1989. 228 pp. £25.00. High nitrogen steels, edited by J. Foct and A. Hendry. 1989. 461 pp. £49.50. Proceedings of the First International Calcium Treatment Symposium. 1988. 116 pp. £15. New cored-wire injection techniques, particularly as Design for recyc/ability, by Michael E. Henstock. 1988. 150 pp. £15. Solidification processing. 1988. 549 pp. £45. Marine engineering with copper-nickel. 1988. 103 pp. £18. Characterisation of High Temperature Materials. 3. New journal FMJ International Publications Lid have announced a new quarterly publication, Aluminium Today. 4. Other new publications Algorithms in real algebraic geometry, edited by Denis S. Arnon and Bruno Buchberger. London, Academic Press, 1988. 274 pp. £15.95. Proceedings, Foundry and Heat Treatment 88. R150 per set of 5 volumes, or R40 per volume.

Jan 1, 1989

By S. Langea, H. Lieberwirth

Impact crushers are common machines in comminution plants. Their high size-reduction ratio and relatively simple design, make them a preferred tool even when subjected to harsh wear, and producing a large quantity of fines in some applications. Until now the alignment of the operational parameters was an operator’s responsibility. Due to the random process characteristic this is mostly done based on empirical values and sensor data, such as power consumption. This paper describes a new approach for online process monitoring of the horizontal-shaft-impact crusher. The application of robust, low-cost acceleration sensors enables the permanent observation of the process characteristics. The operational and evaluation methods are determined on the basis of experiments. Subsequently the recorded measurements are analysed in regards of throughput, rotational speed and product particle size distribution. Occurring signal characteristics are described based on physical and technical principles. The measured data of the acceleration sensors at varying operation conditions provide insight in the course of process. The accurate utilisation yields the determination of the preferential process conditions providing the best balance between the pros and cons of an impact crusher. Both the experimental method and the data processing is discussed from a scientific perspective, displaying a completely new approach for the operation of impact crushers. Keywords: Impact crusher, acceleration sensors, data processing, particle size

Jan 1, 2020

By M. Z. Naghadehi, F. F. Nasategay, J. Sattarvand, R. Battulwar, E. E. Gohari

After the recent increase in catastrophic failures of tailings dams such as the Burmadinho, Brazil failure in 2019, the mining industry has actively engaged in the stabilisation of tailings dams. Most of the tailings storage facility (TSF) guidelines suggest a laborious action that can be facilitated through imaging by unmanned aerial vehicles (UAVs). Although UAVs are not unknown to most mining operations, automated rill detection through aerial image processing is a new concept. This study utilises images from sites in the U.S. and employs semantic segmentation with a UNet architecture to detect location and size of these rills. The developed model can be used as a tool for monitoring surface erosion of TSFs.

Sep 1, 2021

By M. R. L. Blackwell

Over the period 1964 to 1969 Conzinc Riotinto of Australia undertook and completed an evaluation of a large low-grade copper orebody on Bougainville Island in the Territory of Papua and New Guinea. From the outset it was clear that the geographic, climatic and topographic characteristics of the area would necessitate a heavy capital outlay on production and support facilities. Both the physical problems and the magnitude of the investment amplified the need for a thorough and rigorous evaluation of the various strategies for exploiting the orebody. In view of the number of independent and inter-related variables and the flow of new data, a computer-based evaluation process extended the scope and depth of the analysis considerably. The system used permitted an iterative assessment and re-assessment of the various strategies with the results becoming increasingly refined with time. This process encompassed the modelling of the orebody, the simulation of alternative operating strategies and the determination of the financial profitability of the project,

Jan 1, 2014

By P. de A. Barbosa, M. G. Bergerman, E. da Fonseca

Located in the state of Pará, Brazil, the Sossego copper and gold mine consists of a heterogeneous geological deposit. Its complexity derives from the hydrothermal alteration, the ore-forming event, which modified the host rocks, such as granite, and metamorphosed volcanic rocks into several mineral assemblages. Different mineral assemblages have led to differences in abrasiveness. A few Bond abrasion tests conducted during the mine feasibility study did not provide a robust abrasiveness database, thus the variation of physical properties for some mineralisation host rocks was not possible. Although several test methods may be used to determine ore abrasiveness, the Bond method is the one most commonly used in the mining industry. Despite being simple to carry out, this test method has certain limitations as to particle size and the amount of ore sample required, which often makes it difficult or even impossible to apply in the early stages of a project and in geometallurgical studies. The Laboratoire Central des Ponts et Chaussées (LCPC) test may provide an alternative, as it requires a smaller amount of fine-grained material. This study aimed to provide data on wear properties of various ore types from Sossego mine using the LCPC method. It included validation for 40 different ore samples using the Bond test as a benchmark. The results showed good correlation, indicating it may be possible to use the LCPC test as an alternative to the Bond abrasion test. A high abrasiveness index was found for acid metavolcanic rock, confirming the results observed in Sossego mill’s operating database, pointing to a mineralogical drive to amorphous quartz. Keywords: Abrasiveness, geometallurgy, copper ore, Bond abrasion test, LCPC

Jan 1, 2020

By C. Chapman, M. G. Reading, M. P. Amsden

Ecstall Mining Limited, a subsidiary of Texas Gulf Sulphur Company, operates the Kidd Creek Mine, a 10000 tons per day base metal producer, near Timmins, Ontario. Two different types of ore are mined and milled: copper-zinc and silver-lead-zinc. At the highly automated Ecstall concentrator the ores are processed by selective flotation in three individual circuits. One of the most important metallurgical tools for process control is a sample system incorporating continuous on-stream X-ray analysis. Recently this system was automated further by the addition of computer control of reagents for two copper-zinc flotation circuits. The computer programs, utilizing optimum seeking methods and smelter contract terms, have increased copper recovery by 1.1 per cent, zinc recovery by 1.4 per cent, and have reduced reagent costs by 16 per cent. Although not expected, copper and zinc concentrate grades were improved slightly as well.

Jan 1, 2014