Search Documents

By G. C. S. Burns

"A system has been developed to simulate the mining of the Mufulira orebody. The main output from the system is a picture-gram from which the start date and effective life of all proposed mining faces can be measured. This information provides schedule dates for the completion of major capital development projects and stope preparation activities.The orebody must be divided horizontally into main levels and vertically into blocks of equal interval. Ore reserves are defined by specifying the tonnage contained in each block and main level. Mining faces are defined by their co-ordinates, and may themselves be split into sublevels. The simulation maintains an echelon between contiguous sublevels. Other face parameters control the speed of mining, the availability and relative priority of the face.The required production from each crusher/shaft system is specified. The technique of simulating the mining process in order to achieve the required production is described."

Jan 1, 2014

By E. Molobi

"Studs are rods threaded on both ends and are used as mechanical fasteners for two or more components. Stud finds usage in industries such as automotive, construction and aviation. The advantage of studs is that they allow for disassembly of components during maintenance. Studs are continuously subjected to both tensile and shear stresses, depending on the application, therefore they should be manufactured from suitable materials that are capable of withstanding all these external forces. Studs are sometimes manufactured from re-sulphurized steel due to its improved machinability; however, there is a certain limit on the amount of sulphur, above which failure may occur. Premature failure of studs has been a common problem, but failed studs are commonly replaced with new ones without conducting failure investigations. The present work investigates the premature failure of two re-sulphurized steel studs used on a rocker arm assembly and recommends alternative materials. The investigation was carried out by conducting visual examination, microstructural analysis, hardness measurements, chemical analysis and a detailed scanning electron microscopy (SEM) investigation on the fracture surface.IntroductionTwo rocker arm studs used on a 16-cylinder diesel locomotive engine failed prematurely after being in service for less than 5 months. The rocker arm studs had a life-cycle of 5 years. The studs were manufactured from resulphurized steel. The paper aims to establish whether re-sulphurized steel is applicable for the manufacture of studs in the automotive industry.BackgroundLocomotives are classified as either electric or fuel-powered. Diesel locomotives are an example of fuel-powered locomotives. This type of locomotive uses a diesel engine as a means for propulsion. An engine converts chemical energy into mechanical energy required for traction. In an internal combustion engine a rocker arm is an oscillating lever that conveys radial movement from the cam lobe into linear movement to open and close poppet valves of cylinders (Husain and Sheikh, 2013). The rocker arms are secured on to the cylinder head by rocker arm studs."

Jan 1, 2016

By E. L. Forner, G. M. Miller, J. Scheepers, A. J. du Toit

"The sizing, designing, and costing of copper electrowinning circuits requires an in-depth understanding of the fundamental relationships between circuit parameters and the practical operation requirements. The aim of this investigation was to optimize total copper electrowinning project cost by mapping the operating limits of key mechanical equipment. The model was compiled by mapping various cellhouse layouts in terms of number of cathodes per cell, crane productivity, stripping machine productivity, and rectifier–transformer (rectiformer) sizing using data tables for sensitivity analysis. These parameters were then collated and evaluated on a cost by size basis. The model provides an optimum band of operation for cellhouse productivity and project capital cost for a typical range of production throughputs, from 10 kt/a to 200 kt/a cathode copper. The information may be used as a high-level selection guide to assist with identifying a costeffective copper electrowinning circuit design for a specific production rate. The data was validated and compared with existing copper electrowinning cellhouses around the world that typically install no more than 84 cathodes per cell. IntroductionThe sizing, designing, and costing of copper electrowinning (EW) circuits require an indepth understanding of the fundamental parameters as well as the practical requirements to optimize cellhouse productivity and capital cost. Although a significant amount of work has been done designing new copper electrowinning circuits, an in-depth evaluation of world operating data reveals that the number of cathodes per cell, which affects cellhouse layout and productivity, is not consistent for a specific production rate (Anderson et al., 2009; Robinson et al., 2003, 2013). Based on this premise, Kafumbila (2017) suggested that there are unanswered questions, such as ‘why are the numbers of cathodes per cell different for copper production rates of 20 kt/a and 40 kt/a?’In this paper, data tables are employed to map the operating limits and costs of key Cu EW equipment. An overall Cu EW project cost map is then compiled by collating optimum cellhouse layout (number of cathodes per cell), optimum crane productivity, optimum"

Nov 1, 2018

By R. V. Ramani, R. Stefanko

"The favorable mining conditions in the United States of America that resulted in the development of the highly productive room and pillar systems are largely disappearing. Increasing mechanization, poorer natural conditions, and greater concern for health, safety and environment gave impetus to the enactment of the Federal Coal Mine Health and Safety Act of 1969. These regulations prescribe more stringent requirements in face ventilation and mine air distribution, necessitating significant changes in existing ventilation systems. Stringent mandatory standards were applied to respirable dust control for the first time, and simultaneous control of both gas and dust has affected the face as well as primary distribution, most notably on haulage entries.The size and complexity of the present-day mining operations, and the need to evaluate various system changes in a limited time, call for scientific methods in mine planning. In this paper, the authors trace the previous applications of computers to mine ventilation planning and discuss the results of their work in applying a ventilation simulator developed at Penn State. The paper includes an analysis of current trends and suggestions for future research and development."

Jan 1, 2014

By A. Marek

The safe and optimal installation of roof support remains one of the biggest challenges in underground mining today. Traditional hand-held, roofbolt installation in conventional mining has been replaced, in a lot of mining operations, by mechanized equipment. This was a first step to moving the operators out of the unsafe working environment and a start on the trend toward a changed support regime in mechanized mining. However, the challenge of handling of the drill steel itself, as well as inserting resin cartridges and bolts, remains a major hazard and the cause of many lost-time injuries. The paper describes and discusses developments in this area, of mechanized bolting and on-board automation, presenting solutions to known problems, achievements to date, and future developments. The solutions presented will identify with addressing customer needs while touching on possibilities for further technology changes, keeping focus on the safety aspect for operators and the need to bring the operators even further away from the unsafe working environment. The-state-of-the-art technology in mechanized bolting equipment is presented and a brief outlook on the past, current, and future developments is given.

Jan 1, 2012

By M. M. Bwalya, F. K. Mulenga

"SynopsisThe application of the attainable region (AR) technique to the analysis of ball milling is currently limited to batch data. This paper introduces the use of the technique to continuous milling.To this end, an industrial open milling circuit processing a platinum ore was surveyed. Samples were collected and later characterized by means of laboratory batch testing. On site, several milling parameters were varied systematically so as to collect data for modelling purposes. These paramters included ball filling, slurry concentration, and feed flow rate. After data analysis, a simulation model of the open milling circuit was developed under MODSIM®, a modular simulator for mineral processing operations. The mill was then simulated and the data generated was analysed within the AR framework.Initial findings reveal an opportunity to gain valuable insight by studying milling using the AR technique. From an exploratory perspective and inasmuch as this study is concerned, feed flow rate, ball size, and ball filling were identified as being pivotal for the optimization of open ballmilling circuits. Mill speed, on the other hand, had only a limited effect on the production of particles in the size range -75 +10 µm.IntroductionGlasser and Hildebrandt (1997) propounded the attainable region (AR) as a technique for the analysis of chemical engineering reactor systems. Results have since been produced and tested on both the laboratory and pilot scales. The method results in a graphical description of chemical reactions by considering the fundamental processes taking place in the system, rather than the equipment. From the plotted graphs, the process and the reactors can be synthesized optimally into a flow sheet.The use of the AR method still has a long way to go as far as mineral processing is concerned. For instance, several articles have reported the application of the AR technique to ball milling: Khumalo et al. (2006, 2007, 2008); Khumalo (2007); Metzger et al. (2009, 2012); Metzger (2011); Katubilwa et al. (2011); Hlabangana et al. (2012). Their main shortcoming has been the exclusive use of laboratory batch grinding data.To address this deficiency, Mulenga and Chimwani (2013) proposed a way by which the technique could be extended to continuous milling. In effect, the batch milling characteristics of a platinum-bearing ore (Chimwani et al., 2013) were used and scaled up to an open milling circuit. Then, with simplifying assumptions, an attempt was made to optimize the residence time of particles inside the mill. Later, Chimwani et al. (2014a) presented some optimization examples involving various milling parameters. The sequence of published articles then paved the way for the study of industrial milling systems with the AR methodology."

Jan 1, 2015

By J P. van Dyk

The dramatic strengthening of the rand against the dollar as well as a decline in quantity and quality of locally available concentrates have had a dramatic impact on Zincor?s operations during the previous two years. Zincor has responded with the implementation of a number of technical improvements to the process to decrease cost and increase revenue and plant flexibility. Among the initiatives is the pre-leaching and pelletising of the zinc concentrate, de-bottlenecking and process improvements in the leach and purification circuits, the introduction of cathode washing and automated cathode stacking in the cell house and the installation of a new furnace to produce pre-alloyed jumbos. This paper will describe these initiatives and others that Zincor have recently taken to stay competitive in changing global base metals market.

Jan 1, 2005

The quality of life in many countries of both the developed and the developing world is strongly affected by the products and processes of mining industries. The first Issue in this new series brings together a set of review articles by leading authorities in the field which, taken together, provide a thorough and detailed survey of many of the key topics of current concern relating to the environmental impact of mining. The level of treatment of most topics is at first introductory but evolves through to the advanced level of current research, backed up by extensive citations of relevant primary literature and other sources. Thus the Issue as a whole will be found equally valuable by students of environmental science and those actively engaged in research related to this theme.

Jan 1, 1995

By M. Khodadazadeh, K. G. van den Boogaart, T. Leißner, L. Tusa, J. Gutzmer, R. Gloaguen, M. Kern

Ore sorting is a technology that is increasingly used to process primary raw materials. Timeconsuming and expensive empirical state-of-the-art test work is carried out to assess whether the use of ore sorting for the enrichment of a particular ore makes technical and economic sense. With the innovative simulation-based approach presented here, it is possible to direct the selection of a suitable sensor based on quantitative mineralogical and textural data, thus avoiding much of the empirical studies. Required data can be collected quickly and cost-effectively using available methods of automated mineralogy. The obtained parameters such as mineral grain size distribution, modal mineralogy, mineral area and mineral density distribution have been utilised in this study to simulate the prospects of success of ore sorting, applying different types of sensors. Empirical tests with commercially available sensor systems have been conducted to experimentally validate the predictions of the simulations. The estimation of the target mineral grade can be further optimised by the use of machine learning algorithms for the integration of automated mineralogy data and sensor data. The approach can easily be adapted to other types of raw materials and thus has great potential to become a key technology for the optimisation of processing experiments. Keywords: Automated mineralogy, hyperspectral imaging, machine learning, ore sorting

Jan 1, 2020

The wage structure of graduate White men in 1979, by Adri Kruger, Pretoria, Human Sciences Research Council, 1979.76 pp. R5,00. (Reviewer: D. G. Malan) Financial Times mining international yearbook, edited by WilIiam G. Nightingale. London, Longman, 1980. 750 pp. £24 by surface, £34 by air. (Reviewer: J. D. Austin) Techniques in mineral exploration, by J. H. Reedman. Barking (U.K.), Applied Science Publishers, 1979. 533 pp. $90. (Reviewer: D. L. Kyle) Practical geostatistics, by Isobel Clark. Barking (U.K.), Applied Science Publishers, 1979. 129 pp. £13,75. (Reviewer: D. G. Krige) Uranium: The balance of supply and demand 1978- 1990, by the Uranium Institute. London, Mining Journal Books, 1979. 61 pp. £8,50 by surface,,£9,25 by airmail. (Reviewer: D. J. Crowe) Wear and abrasion in industry The South African Institute of Mining and Metallurgy and the Institution of Metallurgists (South African Branch) is to hold a colloquium on the topic of wear and abrasion of metals in February 1981. Steel rolling The International Conference on Steel Rolling sponsored by The Iron and Steel Institute of Japan will be held in Tokyo, Japan, from 29th September to 4th October, 1980.

Jan 1, 1980

By C. O. Esterhuysen, J. P. Deetlefs, C. A. Wessels

The productivity indices of the Republic of South Africa compare poorly with those of its competitors in the rest of the world. The theory of productivity is relatively simple, and various models are available to demonstrate this. The problem is how to apply the theory in practice and to convert it into a practical management system that will guarantee results. The secret lies in a management approach that aims at a continuous improvement in achievement and that involves the entire work force down to the lowest level in the process. Good management systems ensuring the necessary attention to, among others, management by objectives, finance, personnel, maintenance, planning, and control are a prerequisite for continued improvement and staff involvement. The net result of such an approach is described by the term performance management, which encompasses the total integration of al a company's management systems.

Jan 1, 1989

By D. Wines

"Slope stability analyses have traditionally been undertaken in two dimensions assuming plane strain conditions. Although three-dimensional analysis techniques are widely available and used routinely for open pits, two-dimensional analyses are still more common due to the relative ease of model construction and the relatively rapid simulation times.Two-dimensional analyses will often produce different results to three-dimensional analyses for the same slope. It is generally thought that two-dimensional analyses will produce more conservative results. The main reason for the differences is the ability of three-dimensional analyses to account for the three-dimensional nature of the various model inputs, including the slope geometry, the distribution of soil and rock mass domains, the orientation of geological structures with respect to the excavation face, the orientation of the in situ stresses, and the distribution of pore pressure. In some cases, for a long, straight slope in basic geological conditions, two-dimensional analyses can provide a reasonable representation of the problem. However, in many cases, the inability of a two-dimensional analysis to represent the true three-dimensional nature of the problem will lead to unrealistic analysis results.This paper discusses the reasons, as detailed above, for the differences in two-dimensional and three-dimensional analysis results. Work by others is summarized, and additional numerical analyses are performed to provide an improved understanding of the effects of slope geometry, structural orientations, and in situ stresses on predicted stability. Case studies are presented for both stable and unstable slopes, and the behaviour of these slopes is related to the three-dimensional nature of the slope geometry and geology.The previous work, the new analyses performed here, and the case studies show that it is often important to provide a realistic representation of the slope in three dimensions in order to obtain reasonable stability analysis results. This is particularly true for hard rock environments where structurally controlled failure mechanisms are most likely. The paper also highlights the fact that back-analysed properties obtained from one analysis technique are not necessarily applicable to forward analyses using another technique."

Jan 1, 2016

By K. M. Seiler

Automation in mining requires accurate maps of road networks on site. Because roads on open-cut mines are dynamic in nature and continuously changing, manually updating road maps is tedious and error-prone. This paper investigates the possibility of automatically deriving an accurate representation of the road network using GPS data available from haul trucks operating on site. We present an overview of approaches proposed in literature and test the performance of publicly available methods on GPS data collected from trucks operating on site. Based on shortcomings seen in all tested algorithms, a post-processing step is developed which geometrically analyses the created road map for artefacts typical of free-drive areas on mine sites and significantly improves the quality of the final road network graph.

Sep 1, 2021

By Z-B. Cheng, X-J. Liu

"Intensive mining of shallow coal seams tends to result in severe subsidence of the ground surface. Surface subsidence is a complex dynamic spatiotemporal process that constantly changes as mining advances. With Liangshuijing coal mine as a case study, 3DEC numerical software was used to simulate the development of the moving subsidence field from open-off cut to full subsidence on the working face. The results demonstrate that the formation of a subsidence field is directly related to the coal seam depth H and the extent of the mine workings. Taking the advance distance of the working face as the unit of scale, the process of surface subsidence can be divided into four stages: micro-change (H/ p), the development of surface subsidence (2H/ p), the formation of a movement subsidence field (3H/ p), and dynamic balance (4H/ p). The changing movement of a subsidence field can be fully described by the characteristics of surface subsidence value, curve slope, and the inflection position. The results provide important technical support for predicting surface subsidence and the temporal–spatial evolution features of mining subsidence. IntroductionChina’s coal output was about 3.52 Gt in 2017 (China National Coal Association, 2018), making it the largest coal producer in the world, accounting for almost half of total world coal production. Coal production and distribution play a vital role in the energy industry of China. However, entire overlying strata, from coal seam to surface, are disturbed as a result of long-term, high-intensity and large-scale mining, causing surface subsidence. This results in groundwater loss, surface desertification, vegetation loss, and mud-rock flows. These issues have become topics of common concern throughout society. According to related research results (Liu 2008), the area of surface subsidence caused by coal mining in China has reached about 600 000 ha, some 0.2 ha (and up to 0.42 ha) of surface subsidence for every 10 000 t of coal produced. Surface subsidence disasters not only damage buildings, water conservancy, transportation infrastructure, and farmland, but also cause adverse effects on individual and community lifestyles, environmental hygiene, and economic development. Deterioration of the ecological environment in mining areas has a long history and is very harmful (Lu, 2015)."

Feb 1, 2019

By Q. Zhang, X. C. Wang, S. Mao

Phosphate ore is an important strategic mineral resource in which apatite is the main valuable mineral. Flotation is the most commonly used method to separate apatite from middle-low grade phosphate rock. Selective flotation separation is based on the difference of physical and chemical properties of minerals occurring at the three interfaces of mineral/bubble/water. Surface and interface chemistry of mineral have been playing an important role in interpreting and governing its flotation phenomenon. In-situ, visualized and high-precision analytical techniques, such as Time-of-Flight Secondary Ion Mass Spectrometry, Atomic Force Microscopy and Molecular Simulation, have been applied to explore and uncover microscopic nature of apatite flotation. Consequently, a great progress at molecular or atomic level on surface and interface chemistry of apatite flotation has achieved in the past decades. In this paper, the research progress of surface and interface chemistry of apatite flotation such as surface wettability, surface-charging characteristics, surface dissolution behavior, adsorption mechanisms of fatty acid collector and depressor on apatite surface were systematically reviewed. This review will be helpful for the development of more selective reagents and efficient technologies for apatite flotation. Keywords: Apatite, Flotation, Surface and interface chemistry, Surface analysis technology

Jan 1, 2020

This volume, which was advertised in the December, 1968, issue of the Journal at a pre-publication price of £4, is edited by W. Ryan of Warren Spring Laboratory and published by the Institute of Mining and Metallurgy, London. It is an up-to-date review of the operations of some 50 or so companies whose activities embrace the extraction and refinement of metals in the United Kingdom. Thirty-four metals are discussed, ranging from aluminium to zirconium and also there are chapters on ferro-alloys, non-ferrous alloys, high purity metals and metalloids, the platinum group metals and the rare earths. The sources of the various metals are given, followed generally by a brief description of the primary recovery process. Thereafter the operations of specific companies that deal in a particular metal are described in some detail. Certain metals such as barium, bismuth, gallium, thallium and zirconium are perforce covered very briefly as their commercial application is limited but in other cases, especially aluminium, copper lead and zinc, fairly detailed descriptions and illustrations are provided. This publication should be of considerable value to students as it presents modern procedures with regard to the refining and uses of the particular metals under review. This information may not be available from text books which in any case tend towards obsolescence. The book should also prove a valuable addition to the bookshelves of practising metallurgists providing, as it does, a schedule of most of the metallurgical companies operating in the United Kingdom. The quality of the paper and binding, the clarity of printing and illustrations and the arrangement of the subject matter are excellent and are subjects for which the editor and publishers are to be commended. R.J.A.

By C. M. Rule

High pressure grinding rolls (HPGR) technology has come a long way in its application for comminution duty in hard rock mineral processing in the last three years. Several major projects in copper, nickel, gold, molybdenum, platinum, and iron ore have opted for this technology. Advances in wear abatement technology have established the HPGR as a reliable machine with the required high utilization and availability. The HPGR captures the imagination as the next step change improvement in ore processing, based on the following benefits: ?Energy efficiency (potentially 10?30% more efficient)?very topical in an increasingly ?green? society, and in times of rapidly increasing energy costs and availability concerns. 2008 has shown this to be especially important in Southern Africa ?High (and stable) throughput with a relatively small footprint ?Lower operation cost ?Liberation benefits ?Creative ?mine-to-metal? system improvements made possible by HPGR. The platinum industry, renowned for its historically conservative approach, has not been left behind with two significant new HPGR installations, one in Platreef application and one in UG2 application, commissioned in 2008. While the decision for the Platreef application was driven primarily by comminution circuit capacity and design imperatives, the UG2 application seeks to develop a flowsheet that will have a significant recovery benefit in addition to capacity increase and reduced operating cost. The Platreef application of HPGR also provides the opportunity to introduce a novel comminution flowsheet and to demonstrate exceptionally low wear rates treating very hard, abrasive and variable ore types. The HPGR lends itself for inclusion in existing SABC circuits to increase the capacity of the plant and mills. With current PGM prices many operations are attracted to the HPGR technology benefits. The HPGR clearly has the potential to transform entrenched opinion and provide decision makers with significant alternative comminution options. This paper aims to provide an overview of the current applications and to speculate on the transforming stimulus that the HPGR exerts on industry.

Jan 1, 2009

By S. A. Hosseini, O. Asghari

"The quantification of mineral resources and evaluation of process performance in mining operations at Gole Gohar iron ore deposit requires a precise model of the spatial variability of three variables (Fe, P, and S) which must be determined. According to statistical analysis there are complex multivariate relationships between these variables such as stoichiometric constraints, nonlinearity, and heteroskedasticity. Due to the impact of these complexities in decision-making, they should be reproduced in geostatistical models. First of all, in order to maintain the compositional and stoichiometric constraints, additive log-ratio (alr) transformation has been applied. In the next step cosimulation, using stepwise conditional transformation (SCT) and sequential Gaussian simulation (SGS) has been used to simulate multivariate data. Through statistical and geostatistical validations it is shown that the algorithms were able to reproduce complex relationships between variables, both locally and globally. IntroductionThe key steps in mining projects are the quantification of mineral resources, definition of mining reserves, and production scheduling. They rely on the construction of a block model that is used to represent basically the spatial distribution of ore grades (Montoya et al., 2012). The determination of grades and tonnages affects risk assessment and economic evaluation of mining projects. Evaluation of process performance in mining operations requires geostatistical modelling of many related variables (Barnett and Deutsch, 2012). Iron ore quality is characterized by multiple variables: not only the iron grade but also the contaminants that interfere in the subsequent steel manufacturing processes. Consequently, the spatial variability of multiple variables must be determined. Key variables are frequently correlated, and such correlations must be honoured during estimation and simulation. Data from iron ore deposits constitutes compositional data; furthermore, relationships the between assay data are often heteroskedastic."

Jan 1, 2016

By G. T. van Rooyen

In this overview of materials engineering, the author, drawing on his long experience from his student days until the present (emeritus professorship), briefly recounts the main developments in this field: dislocation theory, fracture problems, and the development of alternative materials such as ceramics and polymers. He then takes a look at the future, in which he foresees a greater demand for materials engineers, and leading roles for universities and technikons in collaboration with industry.

Jan 1, 1996

By D. Clement

A comparison between hydraulic and pneumatic rockdrills by D. CLEMENT The regulation of compressed-air reticulation systems is very poor compared with that of electrical systems; this means that electrohydraulic rockdrill systems offer greater flexibility, additional power being readily available at the working face. Hydrometallurgy A new journal devoted to all aspects of the aqueous processing of metals is scheduled to appear this year. Entitled Hydrometallurgy, the journal will be published in quarterly issues, one volume per year. Mineral dressing Contributions are invited for the Symposium on Recent Progress in Mineral Dressing in South Africa, which is to be arranged jointly by the South African Institute of Mining and Metallurgy and the National Institute for Metallurgy. Mineraalbereiding Bydraes word verlang tot die Simposium oor Onlangse Vordering met Mineraalbereiding in Suid-Afrika wat gesamentlik deur die Suid- Afrikaanse Instituut vir Mynbou en Metallurgie en die Nasionale Instituut vir Metallurgie gereel gaan word. Rock mechanics The Sixteenth Symposium on Rock Mechanics is to be held at the University of Minnesota from 22nd to 24th September, 1975. The Symposium is the official Symposium for 1975 of the International Society for Rock Mechanics (I.S.R.M.), and the Council for I.S.R.M., consisting of members from 25 countries, will meet during the Symposium. Powder metallurgy The annual meeting on powder metallurgy organized by The Metals Society is this year to be held at the Stratford Hilton Hotel, Stratford-upon-Avon (the notification did not include the date of the meeting). Vacation School The South African Institute of Mining and Metallurgy has great pleasure in announcing its intention of holding a vacation school on the topic of electric-furnace melting. NIM reports Report no. 1681 The determination of sulphur and phosphorus in chromite. Report no. 1687 The viscosities and electrical conductivities of slags associated with the production of high-carbon ferromanganese alloys.

Jan 3, 1975