Search Documents

By G. A. Kordosky

The literature contains several references to the influence of copper solvent extraction reagents on crud formation, but, there is disagreement as to whether the reagent has an influence on crud generation. The results of three pilot plant campaigns, where crud generation was studied as a function of the copper solvent extraction reagent, are reported. These pilot plants were run at operating copper solvent extraction plants using the aqueous solutions being treated by the commercial copper solvent extraction plants. Two of the pilot plant studies showed that the copper solvent extraction reagent had a significant influence on the extent of crud formation while the other pilot plant study indicated the copper solvent extraction reagent had a lesser influence on crud generation.

Jan 1, 1996

By J. D. Miller, C. L. Lin, J. Dong

Nano clay mineral particles such as kaolinite — with primary particles typically smaller than 2 μm in size — can cause significant problems in flotation processes and tailings disposal, including the processing of Florida phosphate rock and Canadian oil sands. In this study, the consolidated state of flocculated kaolinite sediment was examined, and high-resolution X-ray microtomography (HRXMT) was applied to describe the structure of the consolidated sediment. Using this tomographic information, the complex geometry of the channel network structure for the consolidated flocs was established for the first time. With the establishment of the experimental channel network structure, permeabilities were estimated by flow simulation using the Lattice Boltzmann method. Results for kaolinite sediment with and without polymer are compared and discussed. Results for flocculated kaolinite sediment in a gravitational field are also presented and discussed. The results show that as polymer dosage increases, the permeability of flocculated kaolinite sediment increases, and as suspension pH increases, the permeability of flocculated kaolinite sediment decreases.

By Z. Jin, D. DePaoli, P. Zhang

"Phosphate beneficiation in Florida generates more than one tonne of phosphatic clay, or slime, per tonne of phosphate rock produced. Since the start of the practice of large-scale washing and desliming for phosphate beneficiation, more than 2 Gt of slime has accumulated, containing approximately 600 Mt of phosphate rock, 600 kt of rare earth elements (REEs) and 80 million kilograms of uranium. The recovery of these valuable elements from the phosphatic clay is one of the most challenging endeavors in mineral processing, because the clay is extremely dilute, with an average solids concentration of 3 percent, and fine in size, with more than 50 percent having particle size smaller than 2 µm, and it contains nearly 50 percent clay minerals as well as large amounts of magnesium, iron and aluminum. With industry support and under funding from the Critical Materials Institute, the Florida Industrial and Phosphate Research Institute in conjunction with the Oak Ridge National Laboratory undertook the task to recover phosphorus, rare earths and uranium from Florida phosphatic clay. This paper presents the results from the preliminary testing of two approaches. The first approach involves three-stage cycloning using cyclones with diameters of 12.4 cm (5 in.), 5.08 cm (2 in.) and 2.54 cm (1 in.), respectively, to remove clay minerals followed by flotation and leaching. The second approach is a two-step leaching process. In the first step, selective leaching was conducted to remove magnesium, thus allowing the production of phosphoric acid suitable for the manufacture of diammonium phosphate (DAP) in the second leaching step. The results showed that multistage cycloning with small cyclones is necessary to remove clay minerals. Selective leaching at about pH 3.2 using sulfuric acid was found to be effective for removing more than 80 percent of magnesium from the feed with minimal loss of phosphorus.IntroductionFlorida phosphate ore, or “matrix,” as it is called locally, contains three different mineral groups that have to be separated from each other: (1) phosphate minerals, (2) clay minerals and (3) quartz, or sand. As mined, the phosphate and sand particles are embedded in compacted mud, or clay-balls. Before separation can begin, all of the particles must be liberated from the matrix of mud. The very first unit operation in the beneficiation process is to disaggregate the various particles. This actually starts while the matrix is flowing through the multimile pipeline from the mine to the beneficiation plant. While in the pipeline, the matrix is exposed to shear forces as it passes through the various centrifugal pumps along the pipeline. These intense shear forces cause a significant percentage of the sand and phosphate particles to be liberated from the clay-balls by the time they arrive at the plant. Once they reach the plant, the first goal is to finish disaggregating the clay, and follow that by making a size separation at 1 mm. This processing is conducted in the washer, consisting of a large rotating trammel screen and a few stages of log washer, screens and hydrocyclones. In all of the currently operating beneficiation plants, the washer is a large structure that receives the matrix, screens it and then discharges a pebble phosphate product sized larger than 1.0 mm and a slurry of liberated clay, sand and phosphate particles that are smaller than 1.0 mm."

Jan 1, 2017

By Omid Frough, Hossein Changani

Application of Tunnel Boring Machines (TBMs) is one of the main solutions to achieve a safe and high-performance method of construction in hard rock and soft ground tunneling. In order to adequately assess the progress and potential impacts of the tunneling operations with the TBM, it is required to record a series of data during the tunneling and process of the data to evaluate the TBM performance. Applying the right machine parameters during the excavation not only delivers an optimum penetration rate, but also prevents extra downtime due to over excavation or wear of cutting tools. In this paper, the effect of machine and operational parameters on TBM downtimes has been studied and supported with the real examples of TBM operation data.

Dec 1, 2022

By M. Fig, A. Juganda, M. Zurhorst, J. Brune, C. Strebinger, G. Bogin

"Understanding the airflow patterns in and around the longwall panel can help to identify poorly ventilated areas that may be prone to methane accumulation. Ventilation network modeling provides quick simulation time, and flexibility in adjusting airway parameters and ventilation controls. Such modeling is effective for analyzing linear ventilation networks in underground mines, but cannot compute flows in caved areas of hard rock mines or longwall gobs. The use of Computational Fluid Dynamics (CFD) enables a more detailed investigation of the interaction between the airflows in these caved areas but requires much longer computational times, designing complex meshes and determination of a variety of modeling parameters. Airway friction factors and ventilation controls are simple to implement in a network model but can be difficult to model and adjust in CFD. This paper will focus on using mine ventilation network simulation to identify and analyze key parameters that are affecting airflow distribution in and around the longwall panels, prior to more detailed analysis with CFD modeling, using the example of a longwall coal mine. INTRODUCTION In longwall coal mine ventilation systems common in the U.S., the main purpose of bleeder ventilation is to dilute methane gas and prevent the formation of explosive gas mixtures in the caved, poorly ventilated gob areas and adjacent mine workings. In longwall operation, these critical areas include the development headings inby the longwall face, and the gob. Methane-air explosions in these areas may be ignited by spontaneous combustion, rock-on-rock friction and other sources. Although rare, ignitions due to rock-on-rock friction caused by roof falls caving into the longwall gob are possible and were suspected in the Willow Creek mine explosions in 1998 and 2000 (Elkins et al., 2001; McKinney et al., 2001). Rock-on-rock frictional ignitions are difficult to prevent, as they occur in inaccessible areas. Therefore, rendering the gob area inert is essential to prevent the formation of explosive mixtures. Research by Gilmore et al. (2015) and Brune et al. (2015) has shown that gob inertization can be a difficult or impossible when using bleeder systems, since the flow of gases through the gob depends on the gob permeability and the amount of fresh air leaking from the face and the immediate roof caving conditions cannot be controlled by the mine operator. Having the ability to predict the location where explosive gas zones (EGZs) form inside the gob will be helpful for designing the best ventilation setup to minimize explosion and fire risks."

Jan 1, 2018

By S. Rupprecht

"INTRODUCTION This paper addresses the prevalence of poor public reporting practices of Coal Exploration Results, Coal Resources and Coal Reserves in southern Africa. Currently, the reporting of coal tonnage without supporting coal qualities or “saleable” tonnes and quality is a poor reporting practice that occurs far too often. Not all coal is equal – therefore it is extremely important that investors or potential investors are provided with the full details of both run-of-mine (“ROM”) and Saleable coal tonnage, their associated qualities and other material and relevant information. Competent or Qualified Persons should note that publicly reported information should be sufficient to enable an informed reader to make a reasonable and balanced assessment of the significance of the information provide. “Companies are encouraged to provide information in their Public Reports, which is as comprehensive as possible” (CRIRSCO, 2013): too often this isn’t the case and material matters are either not reported or inadequately disclosed. According to the South African National Standard (SANS) 10320:2014 draft document - “tonnage and coal quality that will be available for sale, either in the raw ROM state (raw Saleable) at a specified moisture content, or after beneficiation of the ROM coal by processing operations to produce materials at specified qualities, size ranges and moisture contents. The assessments must demonstrate that at the time of reporting, the marketing of the products is reasonably justified. The basis of the predicted practical product yield to achieve the Saleable Coal Reserve must be stated. The moisture basis of reporting shall be stated.” As an example to why coal qualities are so important to the public, the requirements of South Africa’s electric public utility (Eskom) power stations are highlighted. The Kendal power station, commissioned in 1988, operates at a Calorific Value (“CV”) range of 19 to 20MJ/kg, an Ash content between 29 and 34% and Volatiles between 20 to 21%. Other power stations, such as Kriel or Hendrina, may require different qualities such as a CV range of 22 to 23MJ/kg, an Ash content between 20 and 28% and Volatiles between 22 to 23%. Thus, in terms of domestic saleable coal, it isn’t just about reporting the coal qualities but also informing the investor as to which power station the coal is intended to be sold as “boilers are designed to burn particular qualities of coal” and “it is not always possible to transfer coal between stations because of different quality requirements at each station” (Chetty, 2010). Sulphur content is also another important quality with the ideal coal content having a quality of less than 1% Sulphur."

Jan 1, 2018

By Lawrence S. O’Rourke

Pricing for tantalum raw materials experienced explosive increases in the period 1978-1979, and-similar declines over 1980-1982. The causes for this are examined. Negative effects on the industry are highlighted. Analysis is provided of subsequent structural changes within the industry which minimize probability of future pricing excursions. Data on markets, sources of material, and outlines of concentration and extractive processes are reviewed. The conclusion is reached that expanded sources, future flat demand, and a broader international base of industry participants are principal forces in this restructure. Flat demand is reviewed as a function of increasing application of tantalum, but in more cost effective forms. This is driven by technical advance, notably in electronics applications.

Jan 1, 1986

By Doug Brown

The recent expansion of our cities into hilly areas, particularly on the Pacific Coast, has resulted in damage or destruction of many homes due to geological problems such as landslides, soil creep, erosion, subsidence, or groundwater seepage. In southern California, landslides are the principal cause of damage and attention is focused on them. Landslides have occurred due to the reactivation of old slide masses, or have been caused by grading and increased water, infiltration resulting from development.. Reactivation of a portion of the ancient Portuguese Bend landslide in Palos Verdes, Los Angeles County, affected approximately 150 homes. A common type of new failure' occurs when grading has undercut bedding or other essentially planar surfaces so that they dip unsupported out of slope. Other slides have occurred due to the inherent weakness of the material involved. Preventive measures undertaken to eliminate damage in the southern California area have. included areal geologic mapping programs-in-advance of development, enacting or strengthening grading codes, and requiring extensive studies by consulting geologists and soils engineers both during the design stage and during construction. In the design stage, proposed cuts are frequently flattened, lowered or reorientated. Frequently, due to the high cost of land, they are supported by compacted fill buttresses. As a result of these measures, the geologic environment has a major effect on the feasibility, design, and development of, a very substantial percentage of tracts or individual homes.

Jan 1, 1967

By Charles H. McGuirk

The movement of iron ore, limestone and-coal on the great lakes involves an intricate transportation network between mine, dock, vessel, railroad and consumer. The system requires that stockpiling be performed at certain points in the pipeline because of the seasonal closing of the lakes, traditionally, this has been accomplished at origin and destination with a substantial cost. Impact to both the shipper and consumer, From the time that the raw material is removed from the ground, expeditious handling and movement to final destination is threatened by a series of potential delays. An initial movement from mine or processing plant to the upper lake port must be coordinated between rail equipment and dock facility, As each vessel is loaded, a schedule must be developed which routes the cargo to an unoccupied lower lake port. However, if the vessel is not delayed by unpredictable weather conditions on the lake, the boat may still arrive at a port congested with other vessels awaiting their turn to unload.

Jan 1, 1973

By V. K. Gupta

A detailed laboratory study was carried out to investigate the effect of the particle size distribution on the grinding rate parameters, Si, for the dry ball milling of quartz and limestone. Contrary to the present belief, the Si values were found to vary strongly with the particle size distribution. In particular it was observed that: (i) the Si values increased with the fineness of the particulate charge - the increase being more pronounced in the case of the coarser sizes, (ii) the next finer size class had the maximum effect on the breakage of the particles of a given size class, while the coarser size classes had only a slight effect, (iii) the effect of two or more size classes was non-additive, and significant higher order inter-size interactions were indicated. The importance of these results in the context of the analysis, design and scale-up of the comminution systems is discussed.

Jan 1, 1987

By A J. Jonaitis

The DENVER Tube Press is a simple, high pressure (1500 PSI (100 bar» filtration unit, developed for processing difficult-to-dewater materials and to produce a handleable filter cake and clear filtrate product. Lab and pilot testwork conducted in Australia on coal fines (55-70\ -35 micron (400 mesh)) have shown that total moisture contents of less than 20\ are consistently achieved in the final cake products from the Tube Press. Currently, these coal super fines are sent to waste due to uneconomical mechanical dewatering methods, which were only able to reduce total moisture levels in excess of 30%. Calculated, throughput rates for the 500 Series Tube Press exceeded 1700 kg/hr (3750 lbs/hr). Feed solids concentration requirements are between 45 and 50\ to achieve these results.

Jan 1, 1993

By Francis F. Pitard

The presence of elements, minerals, or chemical compounds in materials at very low concentrations is becoming a constantly increasing concern for several segments of the Industry. Some trace elements or chemical compounds may be considered as hazardous, some are simply considered as undesirable In complex processes where they could be constantly recycled and end up as the major factor of decreasing quality for some valuable products. In some other cases, the presence of a trace element or mineral may be highly desirable because of its economical value: precious metals are falling into this category, they probably were the first trace elements to draw our attention. Tremendous quantity of money is spent for analysis at the trace level, also the analytical "tool" has been considerably improved during recent years, but still the sampling aspect of the problem remains obscur for many, and because of it, large quantity of analytical efforts become meaningless. Not only the absence of sampling strategies is badly affecting the representativeness of a large majority of samples, but furthermore for the same reasons, many laboratories are failing In their endeavor to prepare reliable standard reference materials. The reason of this failure has its roots in the unability to estimate effectively the sampling characteristics of the element, mineral, or compound of interest, not to mention the unability to perform precise and accurate complete analysis, so essential for the instrumental analyst (1). In this paper a strategy to perform a better sampling operation is recommended. SELECTION OF A PROBABILISTIC APPROACH AS SOON AS PRACTICALLY POSSIBLE It Is essential to differentiate probabilistic sampling from non-probabilistic sampling. As Illustrated in Figure 1, the sampling operation Is a selection process which could be performed In two different ways: I. A probabilistic selection process according to which all elements of a lot of material to be sampled are submitted to the selection with a same probability of being selected. 2. A non-probabilistic selection process according to which all elements of a lot of material to be sampled are submitted to the selection with different probabilities of being selected.

Jan 1, 1986

By J. C. Edwards, C. C. Hwang

A computational fluid dynamics (CFD) program was applied to fire spread along combustibles in a ventilated mine entry. The rate of flame spread was evaluated for the ribs and roof of a coal mine entry; timber sets; and a conveyor belt. The CFD program models char forming materials with temperature dependent thermal properties. The program solves three dimensional time dependent flow equations with a mixture fraction model for the gas phase reactions. Radiant heat exchange is evaluated for non-scattering gas. The CFD program predicted a flame spread rate of 0.0145 m / s for an actual coal mine fire in which the estimated flame spread rate was 0.0086 m / s. This overestimated flame spread rate was a possible consequence of the presence of inert materials in the mine entry’s roof and ribs. CFD fire spread rate predictions of 0.043 m / s and 0.73 m / s bounded the measured value of 0.27 m / s for fire spread along Douglas Fir timber sets in a tunnel.

Jan 1, 2006

By J. M. Elegante

A belt drive attendant was working underground during his shift at the junction of two belt drives. He worked alone, but communicated with others at the mine by underground phone. At noon his shift foreman stopped by his workstation. At 2:00 p.m. he was contacted by phone by a fellow belt drive attendant. At 5:00 p.m., he was found dead by the oncoming evening shifter.

Jan 1, 1989

By Ronald D. Hill

The occurrence of acid mine Drainage (AMD) with coal mining has been well documented. (1) Less documentation is available of its association with other types of mining, e.g., copper, gold, zinc, and sulfur. Yet there are many locations in the western states where acid mine drainage is as great a pollution problem as in Appalachia and in some cases, because of the high copper, zinc, and arsenic concentrations, they present an even more difficult problem. Until a few years ago, it was generally believed that the neutralization of acid mine drainage was uneconomical thus, AMD was allowed to discharge freely into our streams. However, the demand for good water finally dictated that the mining industry be included under pollution laws. In 1964 the Commonwealth of Pennsylvania passed a law requiring that all active mine discharges meet a discharge standard of pH 6-9, iron less than 7 mg/1, and the water must have a net alkalinity. Several other states now require active mines to treat AMD. In all but a few cases, lime neutralization, often in conjunction with aeration, has been the treatment method used. The high cost of lime as compared to limestone and the poor quality sludge, (slow settling, large volumes, and low solids content) has stimulated work in the utilization of limestone. This paper reports on the current state-of-the-art of limestone treatment of AMD.

Jan 1, 1970

By P. Bevilacqua, G. Ferrara, U. Preti

In the last decade, Meloy developed the IAC - Interfacial Area Conservation - model of liberation. His work included three conservation laws and a mathematical tool called textural transform. This paper reviews the developments and applications of the IAC model. From simple spherical two-phase locked particles with planar interfaces, the model has been developed for curved interfaces and solids with complex textures. Moreover, complex shaped particles and ores having more than two phases have been considered. The model equations give the degree of liberation of the component phases for different ore textures – platy blocky and acicular - as well as for different sue distributions. Lockedness profiles are offered for defining the middlings composition, so that from the model it is possible to predict washability curves.

Jan 1, 1992

"Foreword by Lisa SchlinkSuperintendent, operations, Freeport-McMoRan Inc.,Green Valley, AZ, USAThe sixth annual Student Poster Contest hosted by the Mineral & Metallurgical Processing Division of the Society for Mining, Metallurgy & Exploration was held during the 2015 SME Annual Conference and Expo in Denver, CO. The contest had another record-breaking attendance of 31 entries: 27 graduate and four undergraduate. The universities represented were: Colorado School of Mines, South Dakota School of Mines and Technology, University of Kentucky, University of Utah, Southern Illinois University Carbondale, University of Wyoming and West Virginia University.The competition began with an extended abstract review by a panel of judges selected from MPD members. At the SME Annual Conference, all students displayed their posters, highlighting their research. The students with the top abstracts from the graduate and undergraduate divisions presented their research at the MPD Student Poster Session Wednesday morning. The panel of judges then provided tallied scores for the abstract, poster and presentation to determine the winners of the 2015 Student Poster Contest. The first- and second-place winners of both the graduate and undergraduate divisions received $1,000 and $500 scholarships, respectively. The third through seventh places received $200 each, and all other entrants received $100 each and were invited to join the MPD Luncheon.In the undergraduate division, Annette Hein of the University of Wyoming received first place for her research on “Solvent Extraction of Europium from a Nitric Acid Solution.” Second place went to Jennifer Galvin of South Dakota School of Mines and Technology for her research titled “Solvent Extraction of Neodymium Using PC88A.”In the graduate division, Caelen Anderson of the Colorado School of Mines received first place for his research titled “Fundamentals of Rare-earth Flotation Surface Chemistry: Hydroxamate Adsorption on Bastnasite”. This is Caelen’s fourth year placing in the top finisher. Second place in the graduate division went to Seyed Hassan Amini of West Virginia University for his research on “Ultra Clean Coal Production for the Solar-cell Industry.”The 2015 Student Poster Contest was chaired by Lisa Schlink (Freeport- McMoRan Inc.) and Emily Sarver (Virginia Polytechnic Institute and State University). The panel of judges included Aaron Noble (West Virginia University), Nick Gow (FLSmidth), Ren Bryce (Freeport-McMoRan Inc.), David Perkins (Derrick Corp.), Jim Metsa (Weir Minerals) and Scott Shuey (Newmont).A special thank you is extended to the sponsors of the MPD Student Poster Contest, to all the students who participated and to the panel of judges. Watch for more information on the 2016 MPD Student Poster Contest to be published later this year on http://www.smenet.org/mpd/ and in the November issue of Minerals & Metallurgical Processing."

Jan 1, 2015

By R. L. Lewis

The White Pine Mine is the second largest active underground copper mine in the United States, covering an area of approximately 34 km2 in the Upper Peninsula of Michigan. A numerical flow model of the White Pine Mine was constructed to evaluate engineering controls that would reduce the rate of mine water discharge after closure. Of the passive controls evaluated, the placement of low-flow bulkheads within the mine workings was predicted to offer the greatest benefit, reducing the rate of discharge by as much as 35 percent.

Jan 1, 1996

By Ahmed Alghamdi, Salem AlGharbi, Aisha AlHarbi, Owain Morton, Norah AlMuhaisen

This paper addresses the challenges in optimizing the phosphate flotation process, specifically focusing on the variability in P2O5 recovery. An artificial intelligence (AI) driven Flotation Prediction Model was developed to accurately forecast P2O5 grades. Leveraging real-time data from various operational sources, the model provides insights into how operators can opstimize key flotation parameters to enhance product quality and recovery rates. The results demonstrate the effectiveness of AI predictive modeling in addressing operational variability, marking a crucial step toward intelligent operations in the phosphate flotation process.

Feb 1, 2025

By R. K. Singhal

In open pit mining every effort is made to maintain as steep a pit slope as possible. Pi t slope angles are influenced by numerous factors some natural that are amenable to limited or no control at all and other mining technology related where a greater degree of influence can be exerted by the engineer. One such area where control is possible is the method of drilling and blasting in the pit. This paper discusses the influence of blasting techniques on the economics of pit slopes and demonstrates how balanced blasting can be used with advantage to pit wall control and improve fragmentation (thus reducing material handling costs). Microprocessor based instrumentation to monitor drill and blast performance has also been described.

Jan 1, 1988