Search Documents

By B. J. Scheiner, D. A. Stanly, P. M. Brown

The Bureau of Mines has developed an equation that describes the dewatering of clay slurries with poly- ethylene oxide. This dewatering equation is: A[ ] = KC + b where n, k, and h are empirical constants and C is the concentration of polymer solution used for dewatering. The minimum amount of polymer required for dewatering, A, is determined by titration of the clay slurry with a polymer solution. In this report, the dewatering equation is applied to data obtained for a polyacrylamide dewatering sequence. Fundamental similarities between the dewatering properties of clays and the viscosity of polymer solutions were observed. These similarities were explained by correlating an equation describing polymer configuration in solution with the dewatering equation. This correlation showed that the amount of polymer required for dewatering and polymer solution viscosity are both the consequences of the frictional interaction of entangled polymer coils.

Jan 1, 1991

By Arthur C. Pincomb, Alan R. Shapiro

A public awareness of and commitment to abate pollution of water, air, and soil continues to stimulate demand for industrial minerals and rocks capable of neutralizing strong and weak acids. The role of acid neutralizing agents is 1) to treat acidified water and soil until the desired pH is attained and 2) to remove acid-forming compounds from industrial processes to mitigate the formation of acidic discharges. Environmental applications for these agents include: acid rain mitigation, neutralization and prevention of acidic industrial process discharges, and treatment of acid mine drainage and coal refuse. Desulfurization of industrial flue gases involves removal of sulfate compounds capable of combining with hydrogen to form acids. Details of flue gas desulfurization are covered in the previous chapter on Flue Gas Desulfurization. Ideally, the neutralization of acids results in an upward adjustment of effluent pH 7, or neutrality. The final pH value for many acid treated wastes, especially industrial discharge streams, is commonly over neutralized to pH 8.5 to 9.5. The Clean Water Act sets the upper discharge limit at pH 9. ACID NEUTRALIZATION REAGENTS Acid neutralization is accomplished by adding alkali metal and alkaline earth metal compounds to acidic water or soil until the desired pH is attained. The commonly used alkali ions are calcium (Ca), magnesium (Mg), sodium (Na), and potassium (K). Sodium hydroxide, high calcium and dolomitic hydrate, high calcium and dolomitic lime (quicklime), high calcium and dolomitic limestone, soda ash, and magnesium oxide are the compounds most commonly applied to raise the pH of acidic waters or soils. Limestone and dolomitic limestone, which are calcium and magnesium carbonates, and their equivalent oxides and hydrates formed by calcination, are the industrial materials most commonly used in the manufacture of reagents for acid neutralization. Approximately 327 kt of high calcium and dolomitic lime were consumed for acid neutralization purposes in 1988. Magnesite and brucite are industrial minerals that compete with dolomitic limestone for the magnesium-oxide market. Production of caustic calcined magnesia for neutralization purposes exceeded 6 kt in 1990. Soda ash is an industrial mineral gaining increased acceptance in the neutralization of acid waste discharges. Approximately 182 kt of soda ash were consumed in 1990 for acid waste treatment or acid prevention by flue gas desulfurization. Other mineral products either consumed in minor quantities or receiving attention as future neutralizing agents include zeolite and hectorite. In some cases, waste products have been found to be suitable and cost effective for neutralization of acids. Common wastes gaining acceptance include basic slag, phosphate mining refuse, cement kiln dust, fly ash, and mine tailings.

Jan 1, 1994

By E. O. Mixon, Joseph P. Sehulster

This paper describes the driving of a 1421 m long by 2.74 m diameter sewer tunnel in postglacial soils of the Menomonee River Valley in Milwaukee, Wisconsin. An earth pressure balance machine was used for excavation and to install a "one pass" pre-cast concrete gasketed segmental liner. Also discussed is the use of ground freezing to stabilize the ground for the start of tunneling operations and modifications made to two structures to accommodate final tie-ins for the sewer tunnel.

Jan 1, 1989

By F. G. Boehm, T. S. Golosinski

This paper identifies the components of belt conveyor shifting force as a vertical force, Pv, a lateral force, Ph, and a longitudinal force, Pl. A method for estimating these forces is proposed that relates each of their values to the properties of the conveyor structure and rails, the shifting operation parameters, and other site-specific conditions. The effect of this force on the shifter behavior is analyzed, and guidelines are developed for selecting a suitable shifter. As well, other equipment requirements for the shifting operation are discussed.

Jan 1, 1988

By Alexander Filimonov, Yury Bloshteyn

The development of a high-efficiency control system for mine ventilation is a complicated scientific and engineering problem. As a result of high-costs and difficult conditions involved in experiments for the development and investigation of mine ventilation systems, simulation is a critical task in cost reduction and productivity. The paper presents the description of a universal simulation model for controlled aerodynamic processes in an Underground ventilation Network (UVN). The high-efficiency programming tool to design and investigate mine ventilation control systems (MVCS) is also suggested.

Jan 1, 1991

By R. Michael Craig

The flood basalts of the Columbia Plateau in eastern Washington State are under investigation for suitability in siting a deep geologic repository for high-level radioactive waste. To support safety and feasibility evaluations of the proposed repository construction and operation, an assessment is necessary of the potential for inflow of groundwater to the repository excavations from the surrounding saturated rock. Preliminary estimates of inflow are presented using simple models appropriate to the current understanding of available data. Both normal and bounding analyses are presented.

Jan 1, 1986

By Ruth A. Maurer, Steven L. Capt. Van Drew

Coal preparation for a company having several sources of coal and several contracts for sale of coal was modeled. The objective was to minimize wash loss by selecting the quantity of coal to be supplied from each source and the appropriate washbox specific gravity setting to yield contract quality for a given shipment. constraints inposed by silo and stockpile sizes, plant and rehandling capacities, and varying coal quality specifications were included in the model. Solution is by iterative linear programming on an Apple II.

Jan 1, 1987

By Wen H. Su

Extensive investigation has been conducted to determine the causes of a series of roof falls occurring in a room-and-pillar working located in southern West Virginia. Underground observation, along with laboratory testings and finite element analyses were conducted to search for possible mechanisms for the roof falls. Results of the investigation have led to a better understanding of the mechanisms involved in the roof falls. Necessary modifications of mine layout and roof support plan are proposed for improving safety and profitability at the mine.

Jan 1, 1984

By E. Koufetzis

Rock mass classification systems are core elements of tunneling and empirical mine design worldwide. The Bauxite division of S&B Industrial Minerals S.A. decided to implement a rock mass classification system in order to provide mining engineers and supervisors of the underground mines, with guidelines of stability performance and with a complementary tool for the selection of the appropriate tunnel support. The back analysis system employed is based on visual observation of especially selected underground mine sites, representative of all rock types. This fact combined with the failure or success of the already existing support system, constitute the fundamental part of the work undertaken. The paper is divided into three main parts. In the first part the classification methods of Q, RMR89 and GSI are presented and the advantages and disadvantages of each method in connection with underground mining are indicated. RMR89 and GSI are conclusively selected for use, the main criteria for the selection being, the simplicity in use and the competency of the support system suggested for each rock mass category. The second part points out the methodology for measurements, the practical difficulties encountered during this process and the guiding principles followed, in order to avoid these problems. In the third part, the final conclusion of this project is demonstrated and the different rock mass categories are presented with their relative support recommendations, as they were applied and tested in all phases of the bauxite mines? exploitation. The generated methodology is being implemented by the site mining engineers, for validation and potential improvement.

Jan 1, 2008

By J. Stachurski, N. A. Abdel-Khalek

Laboratory Potation tests were carried out on six Polish coal samples of different rank. Each coal sample was screened into seven size fractions. The floatability of size- by-size for various size ranges for different samples was investigated as well as for the original samples. The results showed that in flotation of size-by-size, the intermediate sizes varied with the rank of the coal. Entrainment was shown to be an important mechanism in the recovery of fine particles in flotation of the original samples.

Jan 1, 1991

"?irovski Vrh" Uranium deposit in Slovenia is type of mineralized sediments in ore bearing belts of deflected S-structure, in which the belt is less than 25% mineralized. Ore bodies of irregular small thickness, unreliably contoured, made difficult estimation of correct contours, which are necessary for design and exploitation works. The deposit was explored by vertical boreholes made at the surface and by boreholes fanned from drives. For the purpose of application of this estimation method, 1 m composites have been made in slices which were parallel to the referential belt plane. Estimation was made for 1,5m x 1,5m x lm blocks which do correspond to the size of the containers in the ore transport stage. Two variables have been used: the first, indicator of function (ore=1, waste material =0) and kriging method; the second, logarithmical content of Uranium and Minimum Mean Square Error Estimation (MMSEE) method. Based on estimated values of those variables, probability of ore quantity as well as Uranium content over determined cut-off were calculated for each block. Those two parameters enable determination of the most probable form of the ore body in ecah one metter slice. Estimation of sixteen small blocks in a large 1,5m x 1,5m x 1m block made possible estimation of ore quantity and its content for the determined cut-off, as well as categorization of exploration. This method is being used for estimation of ore reserves and planning of exploration operations. The described' methodology was tested in an exploitation block.

Jan 1, 1986

By R. Brough, T. K. Moller

There are differences in design aspects between steel and rubber linings in grinding mills. This paper describes the basic design rules for rubber liners for different grinding applications. When converting a mill from steel to rubber liners, the design must be changed from such familiar steel liner shapes as wedge bars and plates, wave liners, and ship-lap, to take advantage of the characteristics of rubber. Very little of the knowledge of the wear properties of steel can be used for the design of rubber mill liners.

Jan 1, 1990

By W. H. Su, S. S. Peng

Extensive investigation has been conducted to determine the causes of a series of roof falls occurring in an underground coal mine located in southern West Virginia. Underground observation, along with laboratory testings and finite element analyses, were conducted to search for possible mechanisms for the roof falls. Results of the investigation have led to a better understanding of the mechanisms involved in the roof falls. Necessary modifications of mine layout and roof support plan are proposed for improving safety and profitability at the mine.

Jan 1, 1987

By Dale R. Ralston, Roy E. Williams, Gerry V. Winter, George L. Bloomsburg

GENERAL STATEMENT Data frequently can be collected by several dif¬ferent methods. The method required for the nec¬essary precision for inflow prediction to mines should be selected and other methods avoided. Pre¬cision monitoring or measuring techniques fre¬quently require more time, expertise, and expense in their implementation that may not be justifiable. The temporal distribution of the data needs also may dictate the method used for data collection. Continuous recording devices may be required for time sensitive data whereas point measurements of other parameters may be adequate. Data needs will vary as the hydrologic investigation proceeds. In¬itial data needs may require only a qualitative col¬lection of data such as the areal distribution of precipitation. Subsequent data needs may require the measurement of ground water levels to the near¬est hundredth of a foot. Data requirements can be difficult to fulfill for ground water systems. This is particularly true for anisotropic, heterogeneous hydrostratigraphic units since the hydrogeologic parameters vary both ver¬tically and areally. Techniques exist for determining the storage characteristics of both unconfined and confined hydrostratigraphic units but these pro¬cedures require the installation of multiple wells in the same unit which may be impractical. Specific tests are discussed subsequently that permit the determination of vertical hydraulic conductivity. Data collected from field procedures or tests are generally preferred to laboratory derived data. This is especially true for hydrogeologic parameters such as hydraulic conductivity. SURFACE WATER SYSTEMS Precipitation Precipitation data can be collected from sources that maintain a historical record. The US Depart¬ment of Commerce, National Oceanic and Atmos¬pheric Administration (NOAA), maintains weather observation stations across the country. Such a sta¬tion frequently can be found near a proposed mine site but the type of weather data collected varies from station to station. Fortunately, precipitation data are collected ubiquitously. The data collected by NOAA can be purchased for the area of interest in the form of monthly and annual tabulations. Private weather stations constitute a second source of precipitation data. Existing data usually are analyzed by one of three methods. The station average method merely sums the depth of precipitation at each station and divides the sum by the number of stations as fol¬lows: [ ] where Pavg is the average precipitation (L), P, is the depth of precipitation at station i (L), and N is the total number of stations. This method is applicable where there are a relatively large number of stations uniformly distributed across the area (Hjelnfelt and Cassidy, 1975, pp. 71-72). The second method, called the Thiessen poly¬gon method, weights the precipitation at each sta¬tion in direct proportion to the area it represents without consideration of topography. The stations are plotted on a map and perpendicular bisectors are drawn on the lines connecting the stations. The polygons formed by these bisectors constitute the area that the precipitation for that station repre¬sents. The overall precipitation can be calculated with the following equation:

Jan 1, 1986

By M. Ge

An in-seam seismic (ISS) - based void detection technique was developed and tested for three general mine conditions: anthracite, bituminous and trona. The detection range tested varied from 80 to 100 m for trona mines and from 33 to 66 m for bituminous mines. High quality and broad band signals were obtained from these tests and were used to delineate the voids. The paper provides a brief discussion on the technical features of this void detection technique, the testing conditions and results, and a general assessment of the technique.

Jan 1, 2010

By Kyle Amoroso, Larry Applegate, Aaron K. McCain

The use of frozen soil as ground improvement and temporary ground support for the excavation and construction of cross passages and adits has gained in popularity over the last decade. Frozen soil provides a number of advantages for this application such as being waterproof, structurally stable, and working well with any soil type. One of the greatest advantages is the ability for the system to be adaptable to the project geometry and site limitations. Multiple case histories illustrate that freezing can occur from the ground surface, from within the tunnel, or as a combination.

Jun 13, 2023

By T. Moller

There are differences in design aspects between steel and rubber linings in grinding mills. This paper describes the basic design rules for rubber liners for different grinding applications. When converting a mill from steel to rubber liners, the design must be changed from such familiar steel liner shapes as wedge bars and plates, wave liners, ship-lap, etc. to take advantage of the characteristics of rubber. Very little of the knowledge of the wear properties of steel can be used for the design of rubber mill liners.

Jan 1, 1989

Many investigators believe that column flotation cells offer significant advantages over standard mechanical machines for the flotation of fine particles. However, because of their unique design and operation, conventional techniques for flotation cell scale-up and design cannot be applied to columns. In an attempt to help alleviate this problems a population balance model based on first principles has been developed for fine particle flotation in a column. Two different terms have been considered in the model, i.e., transport and rate. Transport terms, incorporating fluid flow and bouyancy, are used to describe the movement of air bubbles, unattached particles and bubble-particle aggregates along the length of the column. Rate terms, which describe the bubble-particle attachment process, have been derived from first principle considerations. Because the model is based on first principles, it can be useful for the design, control, optimization and scale-up of column flotation cells.

Jan 1, 1987

By R. A. Paul

WIDCO, operator of the Centralia Coal Hine, chose dredging, a method not commonly used for overburden removal, as the fastest, safest, and most economical method for mining through an alluvial filled valley. Now that the work has been completed, how did the cost and schedule compare with the original estimates? What would we do different next time in preparing for a dredging contractor? What are the potential pitfalls working with a dredging contractor? Would we do it again? When should dredging be considered as an overburden removal option?

Jan 1, 1989

By R. Flattery, Z. Agioutantis

Coal and rock pillar design is critical not only for mineral extraction but also for the safety of the mine operators. Pillar strength can be estimated through numerous empirical formulas that are available in the literature, which are typically based on a statistical analysis of case study data. The limitation of most of these equations is that they only considered the width to height ratio and in situ rock or coal strength for pillars in horizontal seams. The adoption of such equations to estimate pillar strength in inclined seams may overestimate the pillar strength and ultimately lead to a poor pillar design. This paper will discuss different techniques that can be used to estimate pillar strength in inclined seams as well as present preliminary modeling results for stress redistribution around inclined pillars. Factors in the parametric analysis include pillar shapes, geometry, and seam inclination.

Mar 2, 2022