Search Documents

By Z. T. Bieniawsk, C. A. F. F. Santos

The effects of artificial weathering on the mechanical properties of the Loyalhanna sandstone have been investigated. Weathering was simulated in the laboratory by subjecting cylin- drical specimens of rock to alternate cycles of wetting and drying (in distilled water at 2O0C 2 5OC and in an electric oven at 105OC t 1°C, respectively). The total number of cycles was 100 and the geomechanical characteristics of the altered material were determined through uniaxial compressive and indirect tensile ("Brazilian") tests, with the determination of axial and trans- verse strains and monitoring of acoustic emission activity (rate and total event count). Moisture content and weight loss data were collected after each cycle and the mechanical parameters (unconfined strength, indirect tensile strength, young's modulus, Poisson's ratio, permanent set and AE/MS activity) were determined for unweathered specimens and after 10, 20, 50 and 100 cycles of wetting and drying. Hypotheses for the effect of weathering on the geomechanical properties of the Loyalhanna sandstone are proposed as reinforced by petrographic analyses carried out for the different stages of artificial weathering. A methodology for assessing the degree of physical weathering of rocks is proposed based on the number of wetting and drying cycles.

Jan 1, 1986

By C. John Dunnicliff, Birger Schmidt

INTRODUCTION To be effective and useful, monitoring of tunnel construction must be carefully planned throughout all steps. A vital and frequently overlooked step is a clear definition of the specific purposes of the instrumentation. Most tunnel construction monitoring has in the past been of benefit to research, the advancement of tunneling practice, wittingly or not. The development of monitoring instrumentation for the benefit of the project from which the data are recovered has very significant potential for risk and cost reduction of soft ground tunneling. A systematic approach to tunnel construction monitoring, from conception to full implementation, includes at least the following nine tasks or steps: Definition of benefits and purposes; design and project specification to draw full benefits; selection of monitoring parameters; selection of instruments and writing of specifications for procurement and installation; procurement and installation; reading and maintenance; data storage and retrieval; interpretation; implementation. Some of these steps are fairly easy and resolved through the use of established theories and technologies. The difficult ones are those that require the bending of minds, those that involve changes in the ways engineers design soft ground tunnels, the way owners pay for tunnels, and the construction is managed, inspected and controlled. Performance monitoring can be of benefit to the owner, design

Jan 1, 1974

By William A. Vogely, DeVerle P. Harris

INTRODUCTION Perspective The phrase "minerala resource appraisal" is widely and loosely used to refer to any quantitative description of a naturally occurring source of fuels, metals, or nonmetals. This leads to confusion when mineral resources are so conceived, for the term refers generically to information on stocks-mineral endowment, resources, reserves, and potential supply-that differ in ways that are important in economic analysis. Mineral resource and other stock measures- these are not flows, e.g., the supply of minerals-have precise technical meanings, which are presented in this paper. Quotation marks are used to separate the nontechnical use of mineral resource from the technical. The term appraisal also leads to some con- fusion because it too is loosely used. When an appraisal employs probability and statistical methods, the appropriate term is estimationb, not appraisal or assessment. This paper presents a conceptual framework or mineral resource information which renders technical, or well defined, relationships of mineral endowment to physical attributes of the earth's crust and earth processes, as distinct from economic values, and identifies estimation approaches that lead to different economic measures of stocks and flows. An important result of this approach is the distinction between the relevance of mineral resource information to economic and policy issues about potential sup- ply (stocks) and dynamic supply (flows across time). With regard to policy analysis, this paper recognizes that mineral resource information has a cost as well as an imputed value. Such a treatment implies that there is an optimum state of resource ignorance, or enlightenment, for a given policy issue and that the relevant economic issue is the selection of that information strategy and appraisal methodology that is indicated by the optimum state. Until the initiation of the OPEC oil embargo, the demand for information on mineral re- sources and potential supply was limited to occasional studies commissioned by Congress or the President of the United States. In these, mineral and energy resources remained loosely de- scribed. When quantitative estimates were supplied, they were not rigorously made, and the estimates and the methodology accordingly escaped close scrutiny. Usually, neither the geo- logical nor economic bases for estimation were carefully described or critically examined. The imposition by OPEC nations of the embargo on oil caused a sudden change in the public and scientific demands for specific 'resource" appraisals, especially of oil and of uranium. These

Jan 1, 1985

By D. Carlson

At the Freeport Indonesia Grasberg Mine in Irian Jaya, Indonesia, a system of underground drainholes and surface drain wells have been designed and are currently under construction. The underground drainholes are located at elevations of approximately 9,600 feet and the surface drainwells located at elevations ranging between 12,500 and 13,000 feet. Together they will be used to drain the ground water contained within relatively incompetent rock. This drain system will allow for the successful dry mining of the open pit, and provide slope stability of the pit wall. The surface drain well network, when completed will allow for the draining of ground water to the Amole Drift where the underground drainholes are constructed.

Jan 1, 1998

By Armine F. Banfield

Selection of a plant site is becoming increasingly more difficult and important, mainly due to advances in technology, antipollution laws and changing economic, social and community conditions. Discussion falls naturally under three headings: economic considerations, terrain considerations and environmental considerations. Aside from acquisition of surface rights, problems having to do with terrain, or topography, usually can be dealt with by management alone. Economic considerations largely involve decision-making by management plus negotiations with government regulatory agencies acting under set rules. Environmental considerations, such as air and water pollution, townsites, housing, schools, noise abatement, appearance, surface rehabilitation and the like usually are under the control of federal, state or municipal bodies with a large degree of decision-making. Successful solution of environmental problems often requires lengthy negotiations, during which public relations by the mining company play an important part. Existing union regulations or customs may confine decision- making and the establishment of wage rates, working conditions and regulations. These usually require considerable planning and negotiation. Initial production often is delayed by formal negotiations involving environmental considerations. Surface facilities usually can be divided into two broad categories: those for concentrating ores--such as gold, silver, base metals, low-grade iron ore and potash-which should be close to the mine to reduce ore-transportation costs to a minimum, and those where the ore is shipped elsewhere for treatment, such as direct-shipping iron ores, complex high-value ores requiring specialized treatment and ores from which special products are derived for local markets. The long-term aspects of plant-site selection too often are given no or insufficient consideration because of immediate financial limitations. As a result, additional capital expenditures may be required later for relocation of townsites, roads, railroads and plants to provide additional room for extension of open-pit operations, tailings disposal, storage, or danger to foundations through underground subsidence or open-pit mining. In the past, hillside sites for concentrating plants were preferred to take advantage of gravity-feed methods The modern trend, however, is to place as much equipment as possible on approximately the same level. Some costs relating to plant sites are included in this section. They are ranges as of the year 1970, and are offered only as general guides. Such costs will vary widely with geographical location and, of course, are subject to escalation due to increases in wage rates and cost of materials. Items in the bibliography contain more detailed and comprehensive data on specific subjects. Most contain bibliographies of their own.

Jan 1, 1973

By C. F. Bonney

Spherical or oil agglomeration has been recognised for many years as a possible process for the recovery of mineraVmetal values. BP has investigated the potential of spherical agglomeration for a number of minerals as have other workers. Testwork has also been carried out by both BP and others on the selective agglomeration of fine coal. The spherical agglomeration of both minerals and coal depends on the use of an immiscible liquid e.g. a hydrocarbon which is added to a suspension of the solids in water. On agitation the oil is distributed over oleophilic/hydrophobic surfaces and particle impact allows inter-particle liquid bridges to form causing agglomeration. It is also possible to enhance the oleophilicity of the material to be recovered by the use of collectors similar to those used in froth flotation.

Jan 1, 1998

By Manoj Khandelwal, Bright Akuinor Tsidi, Newton Amegbey, Daniel Mireku-Gyimah

This study emphasizes the importance of understanding the factors that influence the throwing of flyrock in mining operations, a significant hazard to both workers and nearby structures. Moreover, it highlights how blasting engineers, when estimating flyrock occurrences and their travel distance, typically rely on input parameters such as powder factor (PF), hole length (HL), subdrill (SD), spacing (S), hole diameter (D), burden (B) and stemming length (ST), while overlooking crucial factors like velocity of detonation (VOD) and charge per bank cubic meter (CPBCM). Through analysis using support vector machine (SVM) modeling in MATLAB, the study underscores the impact of including or excluding VOD and CPBCM on flyrock throw distance.

Jul 1, 2024

By Haydn H. Murray

Common clay includes a wide variety of clay and other fine- grained rocks that are used in many ways. These clays are some- times classified as miscellaneous clay and shale. Most products made from them are fired and include such things as structural and face brick, drain tile, vitrified pipe, quarry tile, flue tile, conduit, pottery, stoneware, and roofing tile. Very large tonnages of these materials are bloated by firing to form lightweight aggregate, and large quantities are used in making portland cement (see the specific chapters in this volume). Uses not requiring firing of a finished product include filler for paint and other products and shale and clay used for packing dynamite in blastholes and for plugging oil and gas wells that are no longer in use.

Jan 1, 1994

By Ahmet Gursoy

Maryland, will be the widest vehicular tunnel ever built by the trench tube method. Careful coordination and planning were required to meet the tight and fast design and construction schedules. During the preliminary design, traditional design drawings were bypassed in favor of 25 preliminary design reports representing major work breakdown structures (tasks). For each task, alternative design solutions were examined and analyzed by means of trade-off studies on the basis of engineering, constructibility, and economic considerations, thus providing an overall conceptual value engineering approach for the entire project. So far, total value engineering proposed by the contractor for Contract I I (largest contract of the project at $245 million) is less than 1.5 percent of the contract value. This is an important indication of the success of the design phase planning.

Jan 1, 1983

By Denise Herzog, Sukumar Bandopadhyay

This paper presents an application of analytical hierarchy pro- cess (AHP) to predict the ranking of three beneficiation methods for a low grade, bulk gold deposit located in the interior Alaska. Seven criteria (attributes) were used for evaluating each beneficiation method. For each criterion a matrix of pairwise comparison between methods was developed. The normalized eigenvector of each matrix scales the beneficiation methods with regards to that criterion. An overall scale is constructed by weighting the scales of all the criteria. Methodology used also indicates a measure of inconsistency. This measure is useful in identifying possible errors in expressing judgments as well as actual inconsistencies in the judgment themselves. The outcome of the pro- cess is the best or optimum beneficiation method, considering all the necessary objectives, criteria, and alternatives in a single integrated framework.

Jan 1, 1996

By T. D. Maki

FMC Gold's Paradise Peak Mine, located 13 km (8 miles) south of Gabbs, Nevada, became operational in April of 1986. Shortly thereafter heap leach testwork began on sub mill grade ore. Presently, testwork continues in combination with production size heaps that account for approximately 6% of total gold production at Paradise Peak.

Jan 1, 1989

By John Marsden, John Mansanti, Jim Arnold, Mike Gleason

DOUG HALBE: We're not quite to the end of our session, but we're close. We've had a lot of fun with some of these spill ideas. But these are serious problems, and I think we might be able to benefit by continuing to compile these. Several years ago, the metallurgists at the various operations of Gold Fields Mining Company had a newsletter that came out every two months for several years. This publication consisted of short articles by the staff at the various operations, plus a few others, on problems they'd had and how they solved them. One very useful article, "Things We'd Have Done Differently at Chimney Creek," was written shortly after start-up. John Marsden was the editor and John Mansanti contributed to it, as did Jim Arnold (our distinguished co-chair) and Mike Gleason. I would be interested, with the permission of the audience, in editing that article to make it a little bit less abrasive and putting it into the record here. I think it's a useful SME function to maintain a list of things we've done wrong in plant design, things we don't want to do again. If we have another open session in the future, would others be willing, even anonymously, to contribute, bring slides, and say "Hey, look at the goofs we made?" [laughter, followed by support from the audience] Okay, we'll plan on that. And we'll try to include the Chimney Creek list in the transcript of this session-perhaps edited a bit.

Jan 1, 1998

By C. Caceres

Fibre reinforced shotcrete in combination with other types of support systems is becoming the leading support method for underground excavations, especially those present in low quality rock masses. Sudden or rapid ground support failure can expose workers to safety hazards, damage to equipment and others resulting in production interruptions that will impact the cost of operation. Knowing the peak and post-peak strength characteristics of the support system over time are of major importance. Round Determinate Panel Testing of fiber reinforce shotcrete is the primary test used by the mining industry to determine strength characteristics; however, the tests are costly and significant manpower is required in a mine environment to build, store, handle and test the panels. For these reasons numerical modeling can result in an effective method to produce realistic results. This paper examines the strength characteristics Round Determinate Panel tests and its ultimate application in underground excavations, using Itasca?s three dimensional particle flow code (PFC3D).

Jan 1, 2010

By Ray E. Harris

All of the major raw materials (silica, soda ash, limestone, and feldspar) needed to manufacture most grades of glass are found in Wyoming. Additional advantages for the manufacture of glass include the state's geographic location, a well-developed transportation network, a favorable tax structure (no corporate or personal-income tax), and low energy costs. Inadequate local markets and prohibitive transportation costs to other markets have been the major obstacles to developing a glass industry in Wyoming, the least- populated state in the nation. The Rocky Mountain region only recently became a major market for glass, especially for the Colorado Front Range and Utah's Wasatch Front. Currently, changing costs of the production of glass, an increased market for con- tainer glass in the Colorado Front Range, and innovative production and transportation ideas (e.g., production of selected types of glass and bulk shipments of specification-glass pellets) favor developing a glass plant in Wyoming. Thus, the Wyoming State Geological Survey (WSGS) and other state agencies have been conducting studies and contacting investors in an effort to attract a glass-manufacturing plant to the state. Between 1987 and 1993, three locations of silica-sand and -rock deposits were studied in Wyoming (Cassa, Plumbago Creek, and John Blue). Funding was provided by the WSGS operating budget and local and state Department of Commerce economic- development grants. The reports on these areas were released between 1988 and 1993. In 1988-89, a California-based company conducted additional drilling and feasibility studies and prepared to construct a glass plant in Cheyenne, using the Cassa silica source. However, due to losses incurred by some of their other investments, the company did not proceed. In 1997, the Wyoming Science, Technology, and Energy Administration (STEA) contracted a market study for glass manufactured in Wyoming, using information provided by the WSGS. The STEA contacted several major glass producers, and a major glass-producing company began feasibility studies in January 1998, for the construction of a glass plant. In June 1998, bids to supply brown beer bottles to the Budweiser brewery northeast of Fort Collins, Colorado, were submitted by at least two companies that were considering glass-plant sites in Wyoming.

Jan 1, 1999

By Terry O. Arney

Ore Reserve Models are well established evaluation and mine planning tools. BY definition, these models are made up of regularly sized blocks, arranged in a three dimensional matrix. Two dimensions correspond to north and east directions, and the third, to the depth or elevation. The dimensions of the blocks need not be equal, but generally at least two of the dimensions are equal. The blocks are located in space by coordinates which are generally translated into index values for computer applications. Each block will have quantitative attributes, such as grades, densities, rock characteristics, etc. assigned to it. The process of assigning values to each block in the three dimensional matrix is the process of ore reserve model development. One of several interpolation procedures may be employed to predict the value of a block, based on surrounding data. Block value models have several uses. The utilization of block models in ore reserve computations is quite common. Here, ore reserves may be calculated by level or by cross-section for the entire deposit. For each ore reserve calculation, multiple cut-off grades may be analyzed to determine the ore reserves under different cut-off conditions. The other major use of block value models is in mine simulation. Through simulation, profitable studies that analyze the effect of alternate ore removal sequences can be undertaken to determine economic optimality. Other studies that are undertaken in mine simulation problems include the evaluation of mine layout, pit slope effects, and the impact of varying cut-off grades.

Jan 1, 1974

By A. J. Lynch, M. J. Lees

Introduction The design of wet grinding circuits may vary considerably according to the duty which is to be performed. Grinding machines which are commonly used in these circuits are rod mills, ball mills, autoge¬nous mills, and pebble mills while size separation machines commonly used are vibrating and wedge-wire screens, hydrocyclones, and rake classifiers. In some circuits, such as those producing feed to cement kilns, all the ore entering the circuit is discharged in a single product stream. In others, such as those operating on magnetite-taconite ores, the feed entering the circuit leaves in two or more streams. Grinding circuits in flotation plants normally include sections in which either the concentrate or the tailings from the primary flotation circuit is reground and these additional sections should be regarded as an inte¬gral part of the grinding circuit. A typical circuit is shown in Fig. 18. Problems in achieving maximum efficiency may occur at three stages: 1) At the design stage when the optimum size reduction flow¬sheet must be selected with respect to the types, numbers, and sizes of processing units. 2) At the operating stage when the correct selection of values must be made for those variables which may be altered while the circuit is off-line but which are constant while the circuit is on-line, for instance the vortex finder diameter of the cyclones. 3) Under conditions of continuous operation when changes in the circuit feed or in the mechanical operation of the circuit may cause undesirable changes in the circuit product. The first two prob¬lems are concerned with optimization, that is, with making the best choice from many possibilities, and the last with control. Optimization Problems. The main purpose of a wet grinding circuit is to produce particles with a sizing distribution which will ensure optimum performance of the later chemical reaction or physical concentration circuits, because it is on the efficiency of these later circuits that the economics of the total mineral treatment process depend. The size distribution of the product from a grinding circuit may be affected by many variables, some concerned with the arrange¬ment and operation of the machines and some concerned with the ore characteristics, and it is important that these should be recognized in the design and operation of the circuit. For instance, in a simple ball mill-cyclone circuit the variables which affect the product size even for constant feed characteristics are shown in Fig. 19. In addition, the rate, size, hardness, and mineralogical composition of the feed will affect the performance of the circuit and the product size. When the circuit contains more than one mill, both the number of choices available and the complexity of the problem are increased consider¬ably. Consequently, one type of problem which is to be solved if an optimum product is to be obtained from an existing grinding circuit is that of circuit design, and this includes arrangement of processing units and selection of those operating conditions which cannot be altered when the circuit is operating, such as mill speed and cyclone inlet and outlet dimensions. The other major problem in optimization is encountered at the design stage when a choice must be made about the type, number, and size of processing units. For instance, for a typical high-capacity size reduction operation, should two circuits each containing one rod mill and two ball mills or three circuits each containing one rod mill and one ball mill be used? Alternatively, should ball mills only be used and if so, how many, what size, and what arrangement?

Jan 1, 1985

By H. M. Breza

Utilization of Bucket Wheel Excavators and Overland Conveyor Systems to remove overburden provides increased productivity and flexibility to a surface mining operation. The utilization of such a system at the Texasgulf Inc. Aurora, North Carolina Mine has significantly improved the overall productivity of the mining operation. System flexibility is evidenced by adaptation to operation requirements such as mining area moves, movement of excavated overburden to designated sites, selective handling of overburden, spoil placement contouring, and providing an environmentally sound and safe operation. System productivity is evidenced by actual case studies relating to overall production, excavation rates, and cost effectiveness.

Jan 1, 1993

By C. J. Webb

Column experiments were performed to determine the ability of Madison aquifer material to adsorb arsenic and other constituents in a heavily mined watershed of the Black Hills in western South Dakota. The Madison aquifer is a karstic dolomite and limestone reservoir that is exposed on the flanks of the Black Hills. Streams that cross the Madison in the eastern Black Hills typically lose all their flow to the aquifer at sinkholes. In this work, Madison aquifer material was obtained for loading of six-inch diameter columns, which were backfilled with Madison aquifer water. Stream water then was allowed to displace the aquifer water during column testing in order to simulate mixing of the two waters at sinkholes and to determined adsorption of arsenic and other dissolved constituents. Initial results show that some adsorption of arsenic occurred when compared to more conservative tracers such as nitrate.

Jan 1, 1999

By Michael Karmis, Emily A. Sarver, Ellen S. Gilliland, Leigh-Anne H. Krometis

"Public engagement is increasingly important in ensuring the success of projects related to energy development, particularly with regard to issues of environmental protection, public health, and socio-economic impacts. This is due to concurrent trends in public behavior, including a rise in public interest in these projects that is not matched by a rise in science literacy, and increasing organization and participation of the public through social media, citizen science, and grassroots initiatives. In recent years, several high-profile incidents have demonstrated that when public concern is ignored or met with a passive response from industry, it can rapidly grow into organized opposition that negatively impacts or wholly derails a project. Engaging, listening to, and educating stakeholders during early planning and development phases are therefore essential to earning credibility and trust. Moreover, maintaining two-way lines of communication throughout the lifespan of a project demonstrates social responsibility and facilitates cooperation, acceptance, and even support from communities and others. Positive experiences with specific projects at a local, community level can influence the larger public opinion of an entire industry sector. This paper presents cases studies of public engagement related to shale gas development (including hydraulic fracturing and pipeline construction), mountaintop removal mining, and management of mixed-use watersheds near surface mining operations. The experiences highlighted in these case studies are used to draw best practices of public engagement for sustainable energy development.Introduction Within the scientific research community, the importance of public engagement has gained increasing recognition. In a 2007 article in Nature, medical researcher, Patrick Taylor, stated that public engagement has both “gone viral” and “gone global” and has the ability to make real impacts to research (Taylor 2007). Nancy Baron, the science outreach director for COMPASS, an organization providing communications training for scientists, provides further evidence for the increasing focus on engagement, including shifting attitudes observed during her own experience as a communications coach and documented in surveys, the recent inclusion of communication and engagement activities in academic tenure review, and the surge of workshops, materials, and other resources available on the subject (Baron 2016). In addition to COMPASS, a number of organizations and institutes have been developed to train scientists for communication and engagement with the public, perhaps most notably the Alan Alda Center for Communicating Science at Stony Brook University, and academic fellowship programs, such as the Leopold Leadership Program at Stanford University and the Wilburforce Fellowship Program, have been established for the same purpose."

Jan 1, 2017

By B. Ollila, L. Brown

As mining fronts converge in sill pillar extraction, the mine seismic hazard can be significantly altered and large seismic events have been known to occur. This study used common seismological tools to analyze the extraction of highly stressed sills from two deep Canadian mines with the objective of characterizing the rock mass failure process and relation to large seismic events. The approach treated a sill pillar as a mine-scale failure process, meaning the temporal and spatial analysis scales needed to exist on a similar scale to a significant part of the mine. The temporal analysis scale overlapped with the entire mining sequence, included several years of data to establish long term change in the characteristics of rock mass failure. The spatial analysis scale included the rock mass surrounding a large part of the convergent mining sequence. To accommodate the large spatial and temporal scales, the highest magnitude 2% of events in the dataset were analyzed. Similar results were shown for sill pillars in both mines. Changes in event location, time, magnitude, energy index and apparent volume were similar to expected behavior of rock failure. Indications of strain hardening and strain softening were observed in the sills. The hardening period was characterized by a high rate of small events, high energy index and low apparent volume, giving an indication of high stress and low rock yield. The softening phase was characterized by a decrease in the rate of small events concurrent with an increase in the rate of large events, low energy index and high apparent volume, indicative of release of stress and increase in deformation. Large magnitude seismicity was strongly related to the softening phase, with several Nuttli magnitude 3.0+ events occurring shortly after the transition from hardening to softening failure regimes. Sill failure was indicated by consistently low EI and low levels of seismicity and seismic hazard in the sill pillar.

Apr 26, 2022