Search Documents

By Henning E. Soderberg, Robert Brien, O&apos

Coal may be the answer to US energy problems, but it also has its drawbacks. If it is crushed, screened, dumped, or moved, the environmental engineer is faced with a dust problem. To control coal dust, at both minimum initial cost and reasonable operating cost, demands a working knowledge of dust control equipment design, as well as the coal handling operation. Here are some guidelines to reduce air volume requirements and cut overall system costs.

Jan 10, 1981

By X. M. Yuan

In the flotation of Zn-Pb ores, sphalerite is floated following copper sulfide activation. In this type of sulfide ore, pyrite is commonly treated as a gangue, and poor selectivity between sphalerite and pyrite/quartz is often reported. But pyrite may also appear in association with gold, and flotation of such auriferous sulfides is of great importance in many countries (e.g. South Africa, Australia). In the cationic flotation of sulfide ores with dodecyl amine, sphalerite can be floated while depressing quartz and pyrite. While in a well-aerated pulp in the presence of lime (especially after oxidation with H2O2) the cationic flotation of pyrite is depressed, oxidation of pyrite in the presence of Na2S makes it floatable with amines even in very alkaline environment.

Jan 1, 2002

By A. D. Davis, J. L. Sorensen, C. J. Webb

Environmental impacts from acidic mine drainage are growing national concerns that are particularly acute in the headwaters of the Rocky Mountain region. In the Black Hills of South Dakota, approximately one thousand mines are inactive or abandoned, most of them in the headwaters of major drainages. This paper examines the Bear Butte Creek basin, a heavily mineralized watershed with significant historical mining impacts and a surface gold mine permitted in 1997. The watershed loses its surface discharge to swallow holes in the karstic Madison Limestone. The integrity of the aquatic ecosystem was monitored with a suite of sitespecific bio-indicators. Stream surveys covered the entire reach of Bear Butte Creek from near its headwaters to the swallow holes in the Madison aquifer. Data from the stream surveys, water-quality sampling, and bio-indicator surveys clearly showed that water-quality impacts are limited mainly to Strawberry Creek and to the area of Bear Butte Creek near and downstream of the town of Galena.

Jan 1, 1999

By J. G. Davis

The St. Peter Sandstone is typically a well-sorted, friable, ultra-pure, fine- to medium-grained, quartzose sandstone with silica content higher than 99 weight percent in places. The sand grains are well-rounded, highly spherical and characteristically frosted. Their size typically varies from 2 millimeters diameter (No. 10 U.S. Standard Sieve Series size) to less than 0.08 millimeters diameter (No. 200 U.S. Standard Sieve Series size). A freshly exposed surface of the formation is commonly white with shades of pink and green. Weathered surfaces are a dirty gray or brown and are case-hardened at many localities. Bedding is characteristically indistinct, and the formation usually appears massive throughout. The rock is cross-bedded and ripple-marked locally. The formation is generally porous, permeable and rarely fossiliferous in Missouri. The St. Peter is continuously present in the subsurface in the northern half of the state and along the southeastern edge of the state. The St. Peter crops out in a narrow band that starts in western Montgomery County and runs southeastward, along the Missouri River, to just west of St. Louis and continues south, just west of the Mississippi River, through Scott County. The outcrop belt varies from less than one mile wide to over ten miles wide, and it is over 150 miles in length. The formation dips into the subsurface radially away from the outcrop band. A notable isolated outcrop occurs in Lincoln County to the north of the main outcrop band. The St. Peter is discontinuously present in the subsurface along a band in the west-central portion of the state. It is not present at the surface or in subsurface in the remainder of the state. The formation averages 80?100 feet thick. There is an estimated 3.8 trillion short tons of St. Peter in Missouri. Sieve analyses on drill cuttings indicate three subsurface locations in northeastern Missouri where the St. Peter is greater than 10 percent by weight of sand falling in the 20?40 U.S. Standard Sieve Series size range. The St. Peter was first produced in Missouri in the 1870s for the manufacture of glass. Since that time it has been used as a paint additive, filler material, polishing compound, filtering media, and recently it is commonly used as a fracture proppant in oil and gas wells. The St. Peter is currently quarried and produced in Missouri from four sites located in St. Louis, Jefferson and Perry counties. In the same area there are at least nine abandoned historic mine sites.

Feb 27, 2013

By F. Mielli

Mine operation managers are constantly tasked with identifying new ways to produce more, while using less. Mine effectiveness and reliability is the foundation of improving operational performance. Timely decisions need to be made in order to identify production waste. Intelligent data needs to be visualized in real-time. Operational events need to be captured with impacts quantified and root causes identified. Unfortunately, complex information technology solutions often have a very poor success rate, with some reports suggesting 30 percent of complex projects are canceled before completion.

Feb 27, 2013

By K. Heasley, A. Yassien, A. Khair, S. Peng

There are three major components of a fully grouted roof bolt which primarily determine its ability to develop and sustain load: the steel rebar, the resin annulus, and the rock/grout interface. The untensioned, fully grouted roof bolt is subjected to loading only when the surrounding rock deforms. Vertical rock deformation is generally a result of strata sagging and bedding plane separation, whereas horizontal deformation is typically a result of bedding plane sliding. These two types of deformation create different types of internal loads with-in the roof bolt, tensile stress for vertical rock deformations and shear stress for horizontal rock deformations. Also, as a result of the mutual load transfer between the rock and bolt, shear stress will be developed along the grout/rock interface. According to the exact bolt loading conditions, different failure modes may occur: bolt axial failure, bolt shear failure, and shear failure along the grout/rock interface. Understanding these possible failure modes and their root causes is the key to eliminating roof failures in underground mines employing fully grouted resin bolts. Using ABAQUS 5.8, a finite element model was developed to simulate the components of the fully grouted bolt and its interaction with the surrounding roof strata. Several models were conducted to investigate how load transfer occurs between the rock and the bolt under different geological and mining conditions. The effects of bed-ding plane location and properties, and strata sequence on bolt stability were studied. Also, the effects of hole roughness on bolt stability were discussed. Bolt axial failure was not observed within the range of the studied parameters; however, a combination of high overburden depth, a bedding plane located at 2 to 3 ft from the roofline or a low coefficient of friction along the bedding plane caused strata sliding and shears failure in the bolt. Also, in the case of a weak immediate roof, the shear stress at the grout/rock interface could exceed its ultimate capacity lead to slippage.

Jan 1, 2004

Every two years, industry leaders and practitioners of tunneling and underground construction gather at the Rapid Excavation and Tunneling Conference (RETC) to learn from their peers about the most recent advances and breakthroughs in this unique fleld. Industry experts from around the world highlight their most recent projects and share real-world experiences. They also share with their colleagues new technologies and methodologies that attendees can take home to their respective projects. The 2013 RETC was held June 23-26 in Washing-ton, D.C., itself home to several major tunneling and underground construction projects. The conference is sponsored by SME. Attendance was 1,384 professionals. The accompanying exhibit hosted 159 companies in 188 booths. A few of the topics covered in the technical sessions dealt with caverns and large spans, contracting practices, tunnel linings, design and planning, geotechnical considerations and instrumentation. The conference was preceded by four short courses, all well attended. They were ?Grouting in Underground Construction,? ?Tunnel Lining Design,? ?Microtunneling Application? and ?Risk, Uncertainty and Hard Decisions.? In addition, a sold-out field trip to D.C. Water?s Blue Plains Tunnel took place following the conference. The Blue Plains Tunnel is part of the agency?s Clean Rivers Project. Also during the meeting, three students each received $5,000 scholarships from the UCA of SME, while another three students each received $2,500 scholarships from RETC (See page 53).

Sep 1, 2013

Recent U.S. mine disasters identified a need for improved training of miners in escape from mine fires and explosions. Researchers at the National Institute for Occupational Safety and Health?s (NIOSH) Spokane Research Laboratory (SRL) have designed fire-escape training software for use in a mine-safety training course. The software allows four trainees to work together in a virtual world via a computer network. Trainees responded favorably and showed a marked improvement in locating the proper evacuation routes on subsequent trials. In collaboration with the Pittsburgh Research Laboratory (PRL), a more elaborate fire evacuation scenario is being developed. Further study is needed to confirm that virtual training will translate to improved safety outcomes in the real world. Keywords: virtual reality (VR), safety, training, mining, mine fire evacuation

Jan 1, 2009

By Robert A. Jankowski, J. Harrison Daniel, Fred N. Kissell

Introduction Longwall coal mining in the US has steadily increased since its introduction in 1960. There are now 108 systems operating. (Sprouls, 1986). Advantages of longwall mining include higher productivity, improved safety, and greater coal recovery. Respirable dust, however, is one of the more serious obstacles to realizing the full potential of longwall mining. Early in 1980, the US Bureau of Mines (USBM) initiated extensive in-house and contract research to identify and evaluate effective methods of controlling respirable dust exposure of longwall face personnel (Niewiadomski, Jankowski, and Kissell, 1981). It was found that several control procedures must be combined to assure compliance, using control techniques appropriate to the dust source. These techniques can typically be grouped into the following categories: reduction of dust generation; dilution of dust; capture or knockdown of dust; and dust avoidance. Control techniques can be divided into basic and effective dust control techniques; additional necessary controls; and optional supplementary controls. This information should allow longwall mine operators to select control methods applicable to their particular operations and to develop a dust control plan that meets Federal dust standards. Basic and effective dust control techniques There are three basic dust control techniques (Taylor and Jankowski, 1982) that should be implemented on all longwall mining operations. • A passive barrier or external water spray system design that confines shearer generated dust near the face and away from the operators. • Large quantities of water through the sprays, particularly the drum sprays, to aid in dust knockdown and prevent dust becoming airborne. • A cutting sequence that allows the shearer operators to work primarily on the intake-air side of the lead cutting drum. Shearer clearer There are some poorly designed shearer-mounted spray systems with nozzles directed upwind at the cutting and loading zone of the intake-side drum. These actually carry dust away from the face and upstream of the drum. Where, it mixes with the clean intake air (Fig. la,) and is carried out into the walkway over the shearer operators. The Bureau developed a novel shearer spray system, called the shearer clearer. It takes advantage of the air-moving capabili-

Jan 10, 1986

By Nick Barton

A recent analysis of 145 TBM tunnels of more than 1000km total length has helped to quantify the time dependence of utilization (U). In fact U = Tm, where T is time in hours and m is a negative gradient of deceleration. In poor quality ground, gradient m has a strong dependence on rock mass quality Q, for example m ˜ -0.5when Q = 0.1. Good investigation is critical for ensuring faster TBM tunneling then drill-and-blasting, which tends not to slow down (in m/hr) as the tunnel length increases. Anew design model called QTBM allows more reliable prognoses be made, and occasionally will disqualify the TBM solution.

Jan 1, 2001

By D. Caiden, C. S. Covil, P. J. Chamley

The paper describes the background to alternative delivery models, drawing on international experience, and introduces Project Alliancing/Contract Partnering, common risks and risk sharing on tunnel projects. A plea for early contractor involvement in design is made before describing some whole life design implications for tunnels. The paper concludes with four short case studies; Channel Tunnel Rail Link in the UK, Hull Waste Water Tunnel in the UK; Island West Sewage Transfer Station in Hong Kong, and the New Southern Railway in Australia.

Jan 1, 2005

By B. Radwanek-Bak

The assurance of future raw materials supply to the EU mineral industry has become, in recent years, one of the most important tasks of the EU Commission. It is focused on creation a new mineral policy within the EU zone. One of the starting points for this activity was identification of the mineral commodities that are critical for the sustainable development and technological progress. The paper presents the glance to this problem from the National Member level. Domestic mineral reserve base as a possible source of critical raw materials for the EU was shown. Poland cannot be considered as its resource base. The source of these raw materials are not only scarce in Poland, but also they are not produced, and their demand is now - and according to forecasts is going to be in the future - met by imports. The raw materials in question are not considered exactly critical for Polish economy, but they are of limited economic importance. On the other hand, their growth is a best opportunity and at once the need to the future sustainable development.

Jan 1, 2011

By A. Supomo, A. Partanen, M. Mular

Although many SAG operators may agree that on-line measurement of SAG feed-size is an attractive notion, applying this information in a control strategy that recovers the investment, engineering time, and maintenance is not necessarily straightforward. The P. T. Freeport Split-Online system was justified based on the assumption that SAG feed-size could be used in a feed-forward control strategy either at the regulatory or expert system control level. Something like “as the feed size changes adjust the throughput to avoid under or overloading the mill” was envisioned. However, following installation and calibration, Cluster Analysis showed that such an approach would not be successful. However, the sensor has been successfully integrated into Freeport’s grinding control strategy other ways. It provides an input to the Kalman filter parameter estimator used in a model-based control strategy that optimizes throughput and grind. The Split sensor also provides a characteristic feed size parameter for use in an on-line work index estimator. This paper describes the calibration and installation of the Split SAG feed-size analyzer, and reviews the evolution of its use in the Freeport C3 grinding circuit control strategy.

Jan 1, 2001

By K. R. Long

Until it was defunded in 1995, the U.S. Bureau of Mines maintained a Cost Estimating System (CES) for prefeasibility-type economic evaluations of mineral deposits and estimating costs at producing and non-producing mines. This system had a significant role in mineral resource assessments to estimate costs of developing and operating known mineral deposits and predicted undiscovered deposits. For legal reasons, the U.S. Geological Survey cannot update and maintain CES. Instead, statistical tools are under development to estimate mining costs from basic properties of mineral deposits such as tonnage, grade, mineralogy, depth, strip ratio, distance from infrastructure, rock strength, and work index. The first step was to re-estimate ?Taylor?s Rule? which relates operating rate to available ore tonnage. The second step was to estimate statistical models of capital and operating costs for open pit porphyry copper mines with flotation concentrators. For a sample of 27 proposed porphyry copper projects, capital costs can be estimated from three variables: mineral processing rate, strip ratio, and distance from nearest railroad before mine construction began. Of all the variables tested, operating costs were found to be significantly correlated only with strip ratio.

Jan 1, 2011

By Hugh Douglas

In the past two years recent increases in silver prices over levels that prevailed for many years have changed supply/demand patterns. On the supply side, a silver mining boom is in progress in the United States and elsewhere. On the demand side, traditional uses of silver by individuals are dropping while industry is conserving. These changes will alter the supply/demand balance and bring about more moderate rises in silver prices, which in turn will impact the mining industry.

Jan 1, 1981

By R. J. Sweigard, R. V. Ramani

G.F. Learning The paper by R.V. Ramani and R.J. Sweigard is a wonderful description of the labyrinthine web that has been spun about the mining industry by energetic bureaucrats and politicians over the past 50 years. The remedy for the problem, however, is not more of the same, but less. That may be difficult for the industry to achieve, for it is not a technical solution but a political one. And the current fervor for more detailed planning at all levels of government and private enterprise has become deeply ingrained. The authors recommend the provision of more information about mining and mineral resources to "macro" (i.e., government) land use planners. They apparently overlook, however, the already strong tendency on the part of most government land use planners to consider themselves omniscient. Thus, giving them more information about the technical problems of mining will only make them want to get more and more involved in the "micro" (private, site specific) mine development and production plans of the individual mining firm. In fact, this has already happened at all levels of jurisdiction from municipal to federal government. Examples are legion. The most effective way to ameliorate the adverse impacts of government land use planning on existing and potential mining operations is to: (1) introduce greater flexibility in the definition of land use zones by local and state governments; (2) adopt realistic and relevant ambient environmental performance standards in governing relationships between mineral land uses and concurrent or subsequent nonmining land uses; (3) allow greater leeway for economic considerations in land use decisions in contrast to the explicit legalistic approach now in vogue; (4) recognize that all minerals are not the same and that sand and gravel mining should not be treated the same as underground metal mining, coal stripping, oil field production, or in situ leaching; and (5) eliminate the notion that mining operators should be responsible for determining in detail the use of land by subsequent owners of mined land. This last bit of conventional ethic really makes no more sense than requiring the builders of every shopping center or government office complex to provide detailed plans for the use of that land when its use for shopping or government is ended. Did the builder of Ebbetts Field plan for Brooklyn after the Dodgers went to Los Angeles? Should the developer of the Bingham Pit plan for suburban Salt Lake City after the copper mining goes to Chile? The nation's mining industry must address these questions before further bankrupting itself to provide more data to planners and spending thousands of dollars per acre to create land that when reclaimed is worth only a few hundred dollars per acre. Reply by R.V. Ramani and R.J. Sweigard We thank Mr. Leaming for his valuable contribution. His views on the problems of land use planning and mineral resources are most welcome additions to our paper. As the title indicates, our paper was more concerned with the impacts of land use planning on mineral resource conservation than with the details of the planning process. On the whole, his five recommendations would be helpful for mineral resource conservation. However, we would suggest that the argument he presents for his final recommendation does not address the differences between mining as a land use and commercial or institutional uses. We believe that this difference is the crux of the issue. We share Mr. Leaming's desire to ameliorate the adverse impacts of land use planning. Possibly the most detrimental impact is the loss of mineral resources. Any development, whether mineral or community, that does not give proper consideration to other resources can result in permanent loss or sterilization of resources. With proper planning, some of these losses can be avoided. As our paper indicated, one factor that limits the consideration of mineral resources, and ultimately leads to their sterilization, is the generally inadequate levels of resource characterization and understanding of the unique nature of mineral resources and mining operations. The last point raised by Mr. Leaming is also important. In terms of reclamation and land use planning in mining districts, we certainly do not advocate spending more than what the results are worth. The main thrust of the paper was to explore the avenues for conserving the mineral resources so that, at some appropriate time, the issue of mining and reclamation can still be addressed.

Jan 4, 1985

By Sam Ash

The Murray Mine was one of the first mechanized cut-and-fill underground gold operations in northern Nevada. At the end of 2002, mine production began to decline. So the mine entered a phase of remnant mining and began preparations to close down. The remaining mining took place along the ore waste boundary in previously condemned areas and in challenging ground conditions. To remain economically viable, new techniques were implemented in operations, geology, engineering and rock mechanics. These improvements pushed the edge of known and accepted mining practices and have allowed the Murray Mine to remain in operation.

Jan 1, 2006

By Satid Therdkiattikul, Donald A. Dahlstrom

By oxidizing the pyrite matrix through biological leaching of precious metals ores or concentrates, better than 90% recovery of gold and silver is achieved. The paper develops three precipitation processes that eliminates arsenic and all other toxic elements in the resulting liquor after the biological reactors. In addition, the precipitates are highly crystalline and resist resolubilization. The latter must be tested for at least six months by EPA test procedures. The three systems are temperature (must be at least 120°C or higher) lime or limestone. A continuous pilot plant was employed for all three systems and complete recommendations are given to optimize Fe/As molar ratio, reaction kinetics (detention time) pH, temperature, wt % feed solids as well as resultant reagent consumption based upon continuous operation.

Jan 1, 1995

By Hendrick A. D. Kirsten, A. Clayr Alexander

Stillwater Mining Company is currently developing a second underground palladium and platinum mine approximately 21 km (13 miles) west of their existing Nye operation in the Bear tooth Mountains of southern Montana. Portals for the two access tunnels required at the new site were excavated in limestone talus to accommodate4.6 m (15 feet) diameter tunnel boring machines. A review of the technical design, field conditions and construction of the portals is presented.

Jan 1, 2001

By Enrique Fernández

INTRODUCTION The high speed rail link between Madrid and Asturias, in the North of Spain, has encountered in the Cantabrian range the biggest challenge of the whole line, a very deep tunnel, 25 km long through a foreseen difficult geology. This tunnel was divided in the following four lots for construction: ¦Lot 1: Pola de Gordón- Folledo. L=10,7 km ¦Lot 2: Folledo-Viadangos. L=4,166 m ¦Lot 3: Viadangos- Los Pontones. East tube. L=10,4 km ¦Lot 4: Viadangos- Los Pontones. West tube. L=10,4 km. Dragados S.A. leading a JV was contracted to design and built the Lot 2 on the captioned Pajares High Speed Railway Tunnel. The Lot 2, comprising the middle third section of the 25 km long tunnel has an additional challenge: the construction of one access from the surface to allow it own construction. Feasibility reports and preliminary design do not foresee the use of TBM due to the risk of squeezing ground at the deepest area of the tunnel. On the other hand, conventional NATM excavation of the twin tunnels and ancillary works, including access shafts were against the expected construction schedule by the client, due to the poor ground foresee at the early stage.