Search Documents

By Harlan L. Kebel

Gypsum, the dihydrate form of calcium sulfate, has a history of usefulness to man dating back several thousand years, and a worldwide industry has been built on the mining and processing of this versatile industrial mineral. However, anhydrite, the other prin¬cipal calcium sulfate mineral, has very limited use, so much so that separate statistics for it are not always kept, but are usually included with those for gypsum. Although often found in close association, the two minerals have important chemical differences in that anhydrite is the anhy¬drous form of calcium sulfate (CaSO4) whereas gypsum is the dihydrate (CaSo4.2H20). These two molecules of combined water result in significant differences in hardness, density, and solubility of the two minerals. Of most importance, however, is the difference in thermal properties wherein gypsum, upon the application of a modest amount of heat, can be converted to the hemihydrate of calcium sulfate (CaSO4 '21H20) or plaster of paris, an intermediate product upon which is based over 90% of the value of all calcium sulfate end products. Anhydrite, on the other hand, is inert at these temperatures and its uses have been limited to only those few cases where calcium sulfate in the anhydrous form may have an advan¬tage. The earliest known use of gypsum plaster dates back some 5000 years to the time of the Pharaohs of Egypt who had discovered that gypsum rock, when exposed to fire, broke down into a powder which, when mixed with water, would form a putty that could be plastered on a rough mud brick or stone wall to make a smooth finish. It was used down through the centuries in a limited way for ornamental purposes, but did not achieve wide acceptance because of the quick (25 to 30 min) setting or hardening time which made it difficult to use. The first real understanding of gypsum chemistry was developed in France about 1755, and the gradual growth of its present utilization dates from that time. In the United States, the first utilization of gypsum was to grind it to a fine material for use as a soil conditioner at about the time of the Revolutionary War, and the term land plaster for ground gypsum was coined and has remained in use. Another cementitious material-lime or calcium oxide-had become the usual plastering material, but by about 1870 a method for retarding the set of gypsum plaster was discovered; today it has almost completely replaced lime as a plastering material. In recent years, gypsum products sold in the United States have reached a total valuation of approximately $2 Gpy as illustrated in [Table 1].

Jan 1, 1994

Nearly as impressive as the machines that will be on display at MINExpo are the massive engines and tires that keep the machines moving. As you can imagine, it takes a special tire and special engine to run these machines. The following is a look at some of the exhibitors that will be at MINExpo displaying engines and tires. Cummins Inc. Cummins Inc. will display a lineup engines from 37kW to 2,983 kW (49 hp to 4000 hp) at MINExpo, representing the most extensive ?smallest to largest? range the company has ever put on display.

Jan 1, 2012

global mining boom and in-creased demand for iron ore has lead to a resurgence in the mining industry in Minnesota. At the combined 81st Annual Minnesota Section of SME Meeting and 69th Annual University of Minnesota Mining Symposium, April 15-16 in Duluth, MN, this resurgence was the hot topic as new mining projects were featured in the keynote session. The meeting attracted more than 400 mining industry professionals, including engineers, executives, mining managers and suppliers from around the world. This year?s theme was ?New Ventures in Mining.? The meeting included concurrent technical papers sessions, a keynote session that featured three distinguished speakers and a panel discussion that provided updates on new mining developments in the state. The Minnesota Section of SME technical papers were presented in concurrent sessions, one on mining and one on mineral processing. The mining session included papers on drilling, ore blending, slope stabilization, dust control and operations management. The mineral processing session included papers on plant-control technology, ball mills, pellet strength and fans. Also offered was an SME short course titled ?Simulation based pellet induration optimization.? The Minnesota Section of SME held its annual business meeting during the conference. The 69th Annual University of Minnesota Mining Symposium technical sessions were held on April 15 and also consisted of concurrent sessions on mining and mineral processing. Mining session topics included logistics management, real-time performance measurement, uses for taconite aggregate and environmental issues. The mineral processing session included papers on ore liberation characteristics, zeta potential studies, induration modeling, fuel optimization and conveyor belts. The combined conference included a tradeshow with more than 80 booth spaces featuring vendors offering products and services to Minnesota?s booming mining industry. More than 900 people, including conference registrants and special invited guests of the vendors, at-tended the tradeshow opening reception. This was the largest trade show in many years ? an indication of the vitality of the mining industry in Minnesota.

Jan 1, 2008

By Hugh R. Rhys

The question of the desirability of recovering cullet from MSW in order to recycle it into the manufacturing of glass containers remains a controversial one. The main factors appear to be: 1. The position of the Glass Container Manufacturers Institute (GCMI), as the trade association for most container manufacturers, is that post-consumer cullet is a vital source of raw material. Present requirements are for: a) Flint cullet b) Non-flint cullet of known mix proportions c) Mixed unsorted cullet of known mix propertions c) Mixed or non-flint cullet of unknown mix proportions. A market balance for these products exists, and this might somewhat limit the outlets for (b), (c) and (d), or severely limit the outlet for (d) alone. 2. The color specifications are rather strict. With cullet admixtures of 20% of the melt or more, and the use of decolorisers in a flint furnace discouraged because their action is reducing in a process which requires an oxidising environment, color contamination in a flint furnace is serious.. For amber and green furnaces (reducing) it is less serious, but in order that the quantity of decolorisers may be controlled, the color balance (as a measure of the Fe and Cr content) of the admixtured cullet should be known. 3. Why not simply color analyze, either by a continuous on-stream or off-stream: photo-electronic analysis, or by systematic batch sampling (with some kind off electronic surveillance of the mainstream) and just send mixed, color measured cullet to only amber and green furnaces? The flint would-be simply included in the mix. This is probably technically feasible, but is subject to the market limitations noted in point1.

Jan 1, 1975

By A. A. El-Midany, R. M. Farag, A. M. Salem, S. E. El-Mofty

Bentonite represents one of the main players in the stability of the drilling mud. Its particle size and particle size distribution affect the physical properties of the drilling mud especially the rheological properties. Therefore, a specific particle size distribution was recommended by American Petroleum Institute (API) for use in drilling mud. To clarify the effect of individual size and size distribution, in this study, the bentonite sample was classified into different size fractions. Each size fraction was tested separately in terms of controlling properties such as filtration loss, plastic viscosity, gel strength, cake thickness, and packing density. The effect of each size fraction on the rheological properties of the suspension was correlated to the behavior of the whole particle size distribution in the bentonite sample. The results indicate that the coarser the particles, the higher the rheological properties; in this case, the API mixture is the highest. The filtration loss and cake thickness for the API mixture are lower than that of the individual size fractions due to its wider size distribution due to the filling of voids between larger particles with smaller ones, which lead to bed compaction and consequently lower fluid loss and cake thickness.

By Davorin Kolic, Harald Wagner

Conventional ground support in accordance with latest state-of-the-art considers proper preparation of geotechnical investigation, structural design, observation during construction and fair risk sharing documents. Depending on the ground, there are different means and methods, reflecting different experiences. The paper is presenting ground support concepts, as mostly used in Europe during the past three decades. It discusses the use of anchors as well as the use of steel arches respectively combinations. It also discusses different applications of plain shotcrete, respectively fibre reinforced shotcrete. As excavation sequence is a major input to create the ground arch, the paper discusses also criteria to create closed ring conditions. Finally deformation criteria will be presented with case histories in order to control stability of the structure.

Jan 1, 2001

By M. T. Ansari

"This article explains the ways in which investment on mining infrastructure is a geopolitical issue. It discusses the effect of installing sufficient infra structure to get the product to the world market, and argues that there is a risk involved in depending on traditional suppliers who wish to invest in the infrastructure. It explains how to make a distinction between dedicated purpose infrastructure and general use infrastructure by examining the positions of the main actors in mining projects. It argues that these positions can not be understood as analogous to projects in developed countries. To conclude, infrastructure is a crucial link in the supply chain to market but the relative size of such projects in relation to the economy means that investors decisions in developing countries have quite different implications from those in developed countries."

Jan 1, 2011

By Fengyu Ren, Ruslan Puscasu, Kunpeng Yu, Gideon Chitombo, Liangliang Kang

Weak rock mass and poor flow of material can cause excessive ore loss and dilution in sublevel caving. This paper proposes a method to establish design parameters for an inclined deposit within a weak rock mass and evaluates its effectiveness through a case study. In order to solve the problem of low production capacity and poor safety conditions of sublevel caving mining at the Yingfangzi silver mine in China and to ensure a smooth production from the refractory ore body, it is necessary to select appropriate stope structure parameters. Based on random medium theory of gravity flow and the improved equation of ore discharge in random medium, an end wall drawing experiment is carried out to determine the optimum design and flow parameters. It was observed from the experiment that, due to the influence of the randomness of particle movement, there is a mismatch in the flow parameter measurement. The flow characteristics and distribution of the marker particles are different from that of the tested particles resulting in large drawbody shape distortion. The study finds that the flow parameters obtained by the new method are more practical and account for drawpoint width and recommends that the new method for determining the sublevel stope height is used when the drawbody is a non-standard ellipsoid. The outcomes have shown a significant reduction in the dilution and improvement in the recovery rates, and the safety and efficiency of mining have been greatly improved.

By Christophe Bragard, Brett Robinson

This paper reflects the challenges encountered during the construction of the light rail tunnels under Boyle Heights, in Los Angeles, California. Equipped with two state-of-the-art EPB TBMs, the construction team undertook the mining of twin bored tunnels in the Los Angeles alluvium. The gassy underground conditions dictated many aspects of the design of the tunnels, as well as the tools and means used for their construction. This paper will detail the challenges encountered during construction, as well as the means, methods and logistics used on the project. Discussion includes: EPB TBM machines with some very unique/specific features; complex assembly sequence due to limited shaft access; final precast concrete liner with double gaskets; NATM cross passage excavation in soft ground and below the water table; compensation grouting; mucking shaft arrangement.

Jan 1, 2007

By LaTasha R. Swanson, Jennica L. Bellanca

Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which present an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current research study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders’ evaluations. The study includes considerations and suggestions for safe technology integration

By LaTasha R. Swanson, Jennica L. Bellanca

Proximity detection systems (PDSs) for mobile machines have the potential to decrease injuries and fatalities. Early adopters of the technology have identified some challenges, which present an opportunity to explore and improve the integration of mobile PDSs in underground coal mines. The current research study applied the task-technology fit framework to investigate the fit between mobile PDS technology and mining relative to health and safety, from the perspective of leaders at two coal mines. Quantitative results from the study show that mine leaders evaluated mobile PDS favorably for training and ease of use, system feedback, user authorization and experience, and less favorably for safety, compatibility, task completion, and reliability. Qualitative results reveal specific task, mine, and system characteristics that may have influenced leaders’ evaluations. The study includes considerations and suggestions for safe technology integration

By Christopher J. Bise

INTRODUCTION The control of nuisance water in a mine is extremely important; left uncontrolled, nuisance water can have a severe effect on haulage, ventilation, production, and the health and safety of miners. To control water in mines, a four-step process is followed: (1) prevention, (2) collection, (3) transportation, and (4) treatment. This chapter will be devoted to the collection and transportation of mine water because prevention is usually dictated by pre-mining conditions and initial planning, while treatment is variable and highly site specific. A mine drainage system is nothing more than a collection of gathering points (sumps), machines that impart energy to the fluid (pumps), transportation ducts (pipes), and control devices (fittings, valves, etc.). A pump does not pull the fluid up the suction pipe; atmospheric or external pressure pushes the liquid up the suction pipe to the pump. All references in this chapter will be to centrifugal pumps, due to their popularity for mine drainage. PUMP CHARACTERISTIC CURVES The performance of a pump is plotted on a graph as an indication of its characteristic. To develop the data points, a test facility similar to that shown in Fig. 1 is established. The calibrated Venturi meter is used to measure quantity, the Bourdon gage measures pressure, and the wattmeter measures power input. Various discharge pressures are obtained by throttling with a gate valve in the discharge pipe. Quantity and power are measured at each of these pressure levels, giving the necessary data for plotting the characteristic curves. Fig. 2 shows a typical characteristic curve for a centrifugal pump. Notice that pressure is measured as so many feet of vertical water column above the outlet level, or head. Knowing the quantity (in gallons per minute), head (in feet), and power input (brake horsepower), the pump's efficiency can be plotted based upon the following relationship:

Jan 1, 1986

By P. D. Chamberlain, R. M. Nadkarni, D. J. Kinneberg

Introduction The relationship between precious metal miners and gold refiners has been uneasy over the years. Reasons for this uneasiness and lack of trust include technical factors, economics of scale, and cultural differences. Technical factors take two forms. First, concentrates, precipitates, and sponge produced at the mine site are notoriously difficult to sample. A nonrepresentative sample can be the cause of misunderstanding and distrust. Dote, however, is relatively homogeneous and can be correctly sampled and analyzed with greater reliability. Second, the technology and chemistry of fine gold and silver production is complex and quite different from dote production. Most mining companies are content not to be involved with additional processing steps. From the standpoint of process economies, it is easy to see why miners and refiners are separate groups. Mine location is dictated by the natural occurrence of ore bodies. Heavy capital investment requirements for infrastructure in remote locations usually limits companies to produce the first marketable product from a mine. Beyond that point, the economies of scale and large capital investments for refineries generally dictate that the outputs of several mines be combined to feed a single refinery. The refin¬ing process is so complex that refineries are generally built in larger cities with a skilled labor pool. Therefore, only the largest mines can afford to refine their own output. Lastly, there are cultural differences between the miner and the refiner. The miner, particularly the small gold miner, is by definition a risk taker in a risky business. Refineries, on the other hand, have historically been operated under legal or implied monopolies approved by the government. The government is interested in owning gold, either for currency reasons or because many national mints are major users of gold coins. It is not surprising, then, to find that miners may regard refiners as part of an unresponsive government bureaucracy or, worse, as "city slickers." It is easy for the two groups to distrust each other with these different backgrounds. The interface between miner and refiner does exist and affects nearly all precious metal mining companies and most refineries. This paper discusses the technical and economic aspects of the interface. It points out how both parties can improve the relationship. Technical interface Precious metals selectively dissolve to produce a pregnant solution. They are then recovered from solution by zinc precipitation (Merrill-Crowe process) or by absorption onto activated carbon. This is followed by stripping and electrowinning. At this point, the mining company must decide whether to ship precipitates (or sponge) to refiners or to produce a dote. Some factors the company must consider are the ability to sample precipitates, concentrates or sponge, security of storage, and production rates. An important factor is the incremental cost (capital and operating) of converting precipitates or sponge into dote at the mine. Generally, mines prefer to melt precipitates or sponge to dote to avoid prob¬lems associated with sampling them. There are three types of fur¬naces used by mining operators to melt precipitates to dote. The first and most widely used is a sil¬icon carbide crucible heated ex¬ternally with a gaseous liquid fuel. The crucible is easy to use and slag can be skimmed before pouring dote. This simple system is capable of handling 1 t/a (32,000 oz per year) gold. It could cost as little as $20,000. More complex systems could cost up to $200,000. The second type of furnace is the gas- or propane-fired rever¬beratory furnace. This is usually used only by large-scale opera¬tors in the silver business. Precip¬itates in reverberatory furnaces come in direct contact with the flame. The large volumes of flue gas can carry significant amounts of dust and fume that must be re¬moved from the gas before dis¬charging it to the atmosphere. In the days when the Rand re¬finery in South Africa used reverberatory furnaces, the silver leaving the furnace in the form of vapor and fume was estimated at 2.2% of the total silver charged to the furnace. The gold in the gases was about 0.03% of the gold charged. Most of this silver and gold was recovered in the exhaust gas scrubber system. These scrub¬ber systems can be more costly than the furnace itself.

Jan 10, 1986

Tellurium (Te) is one of the least abundant elements in the crust and tends to form minerals associated with copper, lead, zinc and iron sulfide deposits. Today, most tellurium production comes from the anode slimes and other wastes generated in metal refining. Most of the current tellurium produced in the world is used as an alloying agent in iron and steel, as catalysts, and in the chemical industry. However, future demand and production could increase because tellurium is increasingly used in solar panels and some electronic devices. Tellurium minerals are found in Au-Ag districts in New Mexico, but were not considered important exploration targets in the past. In New Mexico, tellurium is found associated with porphyry copper deposits in southwestern New Mexico and with Au-Ag veins in the Eureka, Sylvanite, Organ, Lordsburg, Steeple Rock, Wilcox, Mogollon, Chloride, Cuchillo, Hillsboro, Zuni Mountains, White Oaks, and Nogal-Bonito districts. The only tellurium production from New Mexico has been from the Lone Pine deposit (Wilcox district), where approximately 5 tons of tellurium ore was produced. Gold-tellurides are found with gold, silver, pyrite, and fluorite in fracture-filling veins in rhyolite at Lone Pine, with reported assays as much as 5,000 ppm Te. Other districts in New Mexico have potential for tellurium, but require field evaluation.

Feb 27, 2013

By K. Kavouridis

The energy and climate protection policy of European Union (EU), and its Member States adopted in 2007 bridges security of supply, environmental protection and competitiveness. The objectives of the EU energy and environmental strategy cover the foreseeable period till 2020. It assumes all sources of energy will be needed. The objectives for renewable and improved efficiency are ambitious; it must be established if they are also realistic. Coal can continue to make valuable contribution to the security of supply and low price of electricity, only with technologies allowing for drastic reduction of the CO2 emitted of its combustion. The aimed at -20% reduction of green-house gases (GHG) of EU-27 by 2020 is an objective limited in time and content. Europe produces less than 15% of global CO2 and this will be reduced to 10% in 2030. Emissions Trading (ET) is to remain the central instrument for CO2 management, especially in the power sector. ET scheme (ETS) or other mechanisms need designing to create an incentive for investment in higher efficiency and technologies and to Carbon Capture & Storage (CCS). The ETS as the climate protection instrument of the EU can become a heavy burden (high fuel and electricity prices, less security of supply) or it can create a climate for modernization of fossil fuel power plants. The suggestion in this paper of fuel-specific benchmark system for CO2 allocation after 2012 can combine the emission levels to be reached with a strong drive to invest, the necessary investment security, transparency and the principle of proportionality. A Benchmark System as recommended by coal industry could adapt to the different circumstances in the long term and comply with EU energy and environmental policy objectives.

Jan 1, 2008

By Garry Biles

The Eskay Creek Mine is a high-grade gold and silver underground mine in northwestern British Columbia. The mine started operations in late1994. For the first three years, ore was crushed to -50 mm(-2 in.), blended to satisfy smelter terms and shipped to smelters in Japan and Canada. Preliminary evaluations indicated that a complex metallurgical facility, requiring a large capital investment, would be required to recover the precious and other economic metals. So markets for raw ore were identified and underground mining and ore transportation operations began at a production rate of 300 t/d (330stpd).

Jan 1, 2000

By R. L. Grayson, F. Giana, R. Aspinwall

Small-mine and contractor Fatal Incidence Rates have been a problem for over 20 years in the coal industry, and the rates persist as unacceptably high. This paper briefly retraces historical information and data on the continuing problem and recounts the many unsuccessful efforts and initiatives to address the problems effectively. Next the results of a review of international literature on addressing the problems are presented. After focusing on a method to pinpoint the trouble spots more specifically through a nested data analysis, suggestions are provided on how the problem may potentially be addressed more systematically and effectively in the U.S.

Jan 1, 2006

By Joel Lööw, Jan Johansson, Lena Abrahamsson

Industry 4.0 offers new possibilities to combine increased productivity with stimulating workplaces in a good work environment. Used correctly, digitalization can create attractive jobs in safe control room environments, which provide space for the employee’s full expertise and creativity. This is true also for the mining industry. But, to succeed, it is important to analyze the development from a worker’s perspective. What will happen to their work? What skills will be needed in the mine of tomorrow? We must also consider the risks, such as privacy issues, increased stress, and work-life boundaries. These questions must be understood if we are to create workplaces that can attract a young and diverse workforce to tomorrow’s mining industry. In this article, we try to illustrate what the new technology can mean for the individual miners. We formulate the notion of Mining 4.0 (Industry 4.0 in the mining industry), where we try to create an image of how the future might look from a miner’s perspective and how mining companies may navigate their way to a future that works for all miners. To illustrate the range of possible outcomes, we formulate two scenarios: one utopian and one dystopic. At the end of our article, we bring forward six recommendations that can be considered a beginning of a road map for the human side of Mining 4.0.

By Joel Lööw, Jan Johansson, Lena Abrahamsson

Industry 4.0 offers new possibilities to combine increased productivity with stimulating workplaces in a good work environment. Used correctly, digitalization can create attractive jobs in safe control room environments, which provide space for the employee’s full expertise and creativity. This is true also for the mining industry. But, to succeed, it is important to analyze the development from a worker’s perspective. What will happen to their work? What skills will be needed in the mine of tomorrow? We must also consider the risks, such as privacy issues, increased stress, and work-life boundaries. These questions must be understood if we are to create workplaces that can attract a young and diverse workforce to tomorrow’s mining industry. In this article, we try to illustrate what the new technology can mean for the individual miners. We formulate the notion of Mining 4.0 (Industry 4.0 in the mining industry), where we try to create an image of how the future might look from a miner’s perspective and how mining companies may navigate their way to a future that works for all miners. To illustrate the range of possible outcomes, we formulate two scenarios: one utopian and one dystopic. At the end of our article, we bring forward six recommendations that can be considered a beginning of a road map for the human side of Mining 4.0.

By T. Stauffer, B. McGunegle, A. Adu-Acheampong

The Fairmount Minerals, Inc., Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 15-inch-diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially-available, high-volume/low-pressure fans combined with a systematic layout of control structures. The recommended re-design was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2007