Search Documents

By John C. Draper

Little precise information is available on the effect of mining on the surface topography. It is often assumed that after mining the surface will simply sink. This is not an infallible conclusion as is well illustrated in two of the three examples herein. This paper describes the results of an attempt to precisely measure the surface movement in the area around coal pillars left in place for three oil wells in a completely mined and caved area at the Harwick Mine of the Duquesne Light Company. The dates when the various measurements were made are shown on the data sheets and indicate the rate of surface movement. These oil wells are identified as wells Nos. 2, 3, and 6. This mine property is located on the north side of the Allegheny River at Cheswick, Pennsylvania, and extends in a northerly and westerly direction about five miles. The three well pillars are situated on the westerly side of the Bessemer and Lake Erie Railroad some 2,000 feet from Rural Ridge, Pennsylvania (Fig, 1).

Jan 1, 1964

By B. P. Faulkner

In 1974, Allis-Chalmers, in corporation with several iron ore operating companies, began to evaluate direct firing of coal in the GRATE-KILN System. Several coals were ground at the Allis-Chalmers Process Research and Test Center and shipped to Cleveland Cliff's pilot plant near Negaunee, Michigan, where they were used as fuel to pelletize Empire magnetite concentrates in the CCI pilot-scale grate kiln. Pilot plant tests were sufficiently favorable to warrant testing in a commercial-scale pelletizing plant. These tests were conducted at the Empire Mine in the late summer and fall of 1974 and again in the summer and early fall of 1975. In the fall of 1975, Allis-Chalmers Mining Systems Division started a program, in the Advanced Technology Center, designed to develop a laboratory test procedure for the evaluation and study of various parameters associated with the direct firing of coals in a GRATE-KILN System. The initial results of this program were presented at the 50th Annual Meeting Minnesota Section, AIME, January, 1977. This paper will briefly review the initial laboratory work and discuss the latest results obtained.

Jan 1, 1977

By Timothy J. Orr, Robin J. Burgess-Limerick, Jennica L. Bellanca, MARGARET E. RYAN

Powered haulage continues to be a large safety concern for the mining industry, accounting for approximately 50%of the mining fatal accidents every year. Among these fatal accidents, haul-truck-related accidents are the most common, with 6 of 28 and 6 of 27 fatal accidents occurring in 2017 and 2018, respectively. To better understand why these accidents continue to occur and what can be done to prevent them, researchers reviewed the 91 haul-truck-related fatal accidents that occurred in the USA from 2005 to 2018 and performed bow-tie analyses using the final reports published by the Mine Safety and Health Administration. The analyses explore the context of the accidents with a focus on the initiating event, event outcome, hazards present, and possible preventative and mitigative controls. Overall, the vast majority of the accidents resulted in a haul truck colliding with the environment, and the majority of these events were initiated by loss of situational awareness or loss of control. The majority of the hazards were related to design and organizational controls. The results of this study suggest a need to investigate operator decision-making and organizational controls and to focus on improving design and operation controls such as mine design and operational procedures.

Feb 22, 2021

By I. J. Wu

China’s land area, comparable in size to United States or Canada, contains diverse geological environments and mineral resource potential. The diversity in geological environments is such that the potential for developing many world-class mineral deposits in China is good. However, China’s mining sector was not open to foreign investment until the1990s. The long-term prospect for Chinese resource development is attractive because of China’s enormous population and cumulative demand for minerals. Approximately 33 foreign mineral companies, including 11 major internationals, are to various degrees active in China. Chinese mining laws and regulations pertaining to joint ventures with foreign companies are, from the international investment prospective, evolving slowly, but positively. This positive trend is continuing under the current government reform process, which is moving China towards a freer market economy. Although improving the enforcement of relevant laws and regulations is an ongoing process, the environment for mineral investment and joint ventures is increasingly more accommodating to foreign companies.

Jan 1, 2000

By Ashraf A. M. A. Wali

Many of the economic resources of Egypt have been recognized and exploited for thousands of years (e.g. gold and copper). Most of these minerals, particularly those from hard-rock sited deposits, are found in complex form along with other components while those present in sedimentary sequences are largely in simple compounds or as native elements. Recognition of their characteristic settings (structure, basin development, environment of formation etc.) is the main clue in predicting and locating their presence. The main economic minerals exploited in Egypt today come from sedimentary sequences and include sodium and potassium chlorides, gypsum, sulfur, and sedimentary iron ores. Large amounts of low grade sedimentary phosphates are known but are not of economic value at today's prices. Recent intensive investigation in the north-eastern Sinai (EI Arish) and along the southern coasts of the Gulf of Suez has revealed new and extensive sulfur and chloride deposits, and considerable oil and gas are now being exploited from closely related sediments. Tin is the only mineral that is produced from hard-rock sources, and gold and copper deposits are present but not of high enough grade to be economically viable. However, a significant part of Egypt has not yet been studied in enough detail to close the door on future discoveries. Another point of considerable geological interest is the presence of diverse, modern evaporitic settings, from which we may draw the analogs for many of the older gypsum, anhydrite, chloride and sulfur de-posits. In fact these analogs are so well displayed that both the Sinai and Gulf of Suez-Red Sea evaporites (Middle and Upper Miocene) can be readily compared with these modern deposits.

Jan 1, 1990

By Kent C. Condie

Precambrian terranes in the Rocky Mountain region decrease progressively in age from the Archean Wyoming Province (> 2.5 b.y.) to the late Proterozoic in West Texas (figs. 1,2). Within the Wyoming Province, most dates fall near 2.7 b.y. although some are recorded at 2 3.8, 2.9, and 2.6 b.y. Although Penokean (- 1.8 b.y.) deformation and plutonism are recorded in southeastern Wyoming, most Precambrian rocks south of the Wyoming shear zone, which separates the Archean and Proterozoic provinces, are < 1.76 b. years in age. Supracrustal rocks in Colorado, western Arizona, and northern New Mexico fall in the range of 1.72-1.76 b.y., those in central New Mexico about 1.65 b.y., those in southeastern Arizona and southwestern New Mexico about 1.70 b.y., and those in West Texas 1.1-1.2 b.y. The Wyoming Province is comprised chiefly of 2.7 or 2.9 b.y. tonalitic gneiss terranes intruded by 2.6 b.y. granites in the central and southern parts of the province. Supracrustal rocks are minor and include greenstone belts comprised chiefly of pillow- ed tholeiites and graywackes and remnants of quartzite-shale successions. Metamorphic grade in greenstone-gneiss terranes ranges from upper greenschist to amphibolite facies and in quartzite-gneiss terranes from upper amphibolite to granulite facies.

Jan 1, 2013

By Fred W. Brackebush

In underground stopes that require more than minimal support, backfill is almost universally used. The term cut and fill stopingis used in a broad sense in this section, which describes underground mining methods requiring support. Support in stopes can be classified as local or short-term and general or long-term. Local support for the back of a stope, for example, can be accomplished with rock bolts or timber stulls. General support for the walls of the stope is provided by backfill. Local support provides a safe working place for the stope miners. General support, provided by backfill, preserves the access way to the stope and prevents large scale dilution of ore. Supported methods are a set of cut and fill stoping methods using backfill for general support and various local support methods. his section is subdivided into three chapters: 19.1 Cut and Fill Mining 19.2 Excavation Techniques 19.3 Backfilling Methods

Jan 1, 2008

By Cyrus W. Field

Metalliferous sediments constitute an important component of the sedimentary veneer that overlies basaltic oceanic crust of the Nazca Plate and elsewhere. Although first collected more than one century ago near the East Pacific Rise during the Challenger Expedition and recognized for their anomalously high content of Fe and Mn, occurring as very fine-grained, yellow-orange, oxides, hydroxides, and oxyhydroxides, it was not until the more detailed studies of Bostrom and Peterson (1966) that their geologic significance and concentrations of other transition metals were fully appreciated. The Nazca Plate is a dynamic lithospheric unit bordered by the Peru-Chile trench and the East Pacific Rise to the east and west, and by the Galapagos Rift and the Chile Rise to the north and south (Fig. 1). Samples employed in this study were taken from piston core recovered from the Nazca Plate (Fig. 2), D. S. D. P. drill core from the northeast Pacific (Dymond and others, 1973), ferromanganese nodules from dredge-haul s at several locations, and from hydrothermal mineral deposits of the Andes. Our efforts have been largely sponsored by the National Science Foundation through its International Decade of Ocean Exploration Pro- gram. The metalliferous fraction of these sediments is widespread, but generally small. Sedimentation is dominated by biogenic silica in the equatorial latitudes, terrigenous debris adjacent to the South American Continent, and by biogenic carbonate elsewhere, except at depths below 3500 m in the central and northwest parts of the Nazca Plate near the East Pacific Rise. Contributions of these distinctive sediment types are shown by the distributions of Si02, A1203, and CaC03 given in Figure 3.

Jan 1, 1982

By N. M. Levine

This work defines and systematizes the physical factors of the problem of leaching and demonstrates for the first time the utility of macropore volume, micropore volume, specific surface, pore size distribution and permeability as parameters of leaching based on a study of the recovery of uranium from the Top Black member of Chattanooga Shale.

Jan 1, 1962

By Sahendra Ram, Ashok Kumar, Rakesh Kumar, AMIT KUMAR SINGH, Dheeraj Kumar, Arun Kumar Singh, Rajendra Singh

This article offers an examination of a retreat mining method conducted at the Pinoura Mine in India from 2010 to 2017. The method is atypical for coal mines of India’s coalfields. The method executes depillaring in a single pass and does not require the formation of galleries and support installation in splits, thus, reducing the cycle time. A variety of observations are discussed throughout this work and emphasis is placed on field measurements and depillaring under weak roof (RMR = 40–45). This paper discusses design techniques, specifically the estimation of the snook (remnant pillar) size, and important practical observations after the fact. The execution of this method was eventually conducted in eleven panels.

Aug 4, 2020

By S. Hamm

Elevated total dissolved solids (TDS) content in waters downstream from surface coal mines in Central Appalachia is an increasing concern, as unnaturally high TDS and/or associated specific conductivity (SC) may contribute to deteriorated stream ecosystem health. The aim of this preliminary study was to explore the efficacy of accelerated leaching as a means of minimizing long-term TDS/SC generation by problematic overburden materials. Five spoil samples were collected and leached using simulated rainwater solutions under ambient and acidified pH conditions. SC and pH were monitored during each leach cycle, and ICP-MS was used to determine how leaching conditions affected release of specific ions. This paper highlights the results of both jar and column leaching tests. Among the most significant findings was that, for certain spoil materials, SC in leach column effluent was effectively reduced when spoil was leached first with acidic rainwater followed by ambient rainwater (vs. ambient rainwater leaching alone). This suggests that accelerated leaching might aid in long-term stabilization of some materials.

Feb 23, 2014

By SANDEEP KUMAR JENA

This review work reports the recovery of potassiumfromdifferent rocks and mineral sources. The global demand for potassiumis rising consistently due to the growth of agricultural production. A major portion of the world potassium production is consumed in making of fertiliser; however, other uses include those in pharmaceutical, glass, ceramic, food and detergent industries. The availability of soluble potash minerals (sylvite, kainite and carnallite) in different countries like Canada, USA, Israel and Russia makes them as major potash producers, whereas agricultural-based countries like Liberia, Somalia, Central African Republic, Thailand, Indonesia and Malaysia including India meet their potassium requirement through import only. On the contrary, the availability of huge potassium-bearing rocks/minerals (like nepheline syenite, feldspar, mica, glauconitic sandstone) in these countries containing around 4–17% K2O would be a prospective for commercial production of potassium. The potassium recovery from minerals/rocks is very complicated due to the uniform distribution of potassium throughout the crystal structure. Different physico-chemical separation methods like bioleaching, chemical leaching, flotation and roast leaching have been discussed for the successful recovery of potash values from these rocks/minerals. However, the recovery of potassium from hugely available seawater using the chemical precipitation, solvent extraction,membrane separation and ionic exchangemethods is not cost-effective due to the low concentration of potassium.

Aug 31, 2020

By A. Noble

Linear circuit analysis (LCA) is a fundamental tool which has been used to evaluate mineral separation circuits during the preliminary design phase. Traditionally, the LCA methodology uses the analytic circuit solution to determine the relative slope of the circuit?s partition curve. This value is then used as an indicative performance measure suitable for the comparison and ranking of alternative circuit configurations. Unfortunately, the partition curve slope only reflects the separation potential of middling material. In most mineral systems, this material represents a small portion of the initial feed (due to liberation) as well as a small portion of the revenue potential (due to the incremental value). Respecting these limitations, the authors have developed new separation performance indicators which may be derived from the analytical circuit solution and used in LCA problems. These indicators inherently reflect the separation potential of pure material, providing a better indication of lost revenue due to misplaced material. The complete methodology has been integrated with prior software to produce the Heuristic Optimizer for Resource Separation Economics (HORSE).

Feb 23, 2014

By David A. Heitman

The Buick Concentrator is a highly automated operation which utilizes a process control system for continuous monitoring and control. The process control system development, installation, and application to the concentrator grinding and flotation circuits are presented in this paper. The design and implementation of analog field sensing instrumentation, a continuous on-stream X-ray analyzer, grinding and classfication circuit controls, and a recent digital process control system utilizing a centralized computer are discussed. Emphasis is placed on the project planning and installation of the digital control system including a presentation of future plans for continuing application of computer control.

Jan 1, 1982

By Satoshi Honda, Mitsuru Shimizu, Tatsuji Nagao, Motoaki Kurisu, Hirokazu Izumi, Toshinori Takahashi, Hiroyuki Itoi

"1. INTRODUCTION Grade separation of roads and railway tracks is an effective method for solving traffic-related issues in cities. However, in urban areas where the existing traffic infrastructure is already overcrowded, construction of new roads often faces problems especially in the proximity of existing structures. This paper summarizes the construction plan and results of new road tunnel construction in the proximity of the piers of elevated tracks on the Tokaido Shinkansen railway.2. SUMMARY OF CONSTRUCTION AND ISSUES Auxiliary Route No. 26 as specified in the Tokyo urban plan is a project by the Tokyo Metropolitan Government, covering the construction of a new road with a total length of 22.3 km currently on the way to completion. In Shinagawa Ward, Tokyo, Auxiliary Route No. 26 is designed to cross the railway tracks of the Yokosuka Line and the Tokaido Shinkansen Line, so for this project, the East Japan Railway Company (JR East) was commissioned to design and build a road crossing under the railway tracks (Sumiyoshi Underpass). Figures 1 through 3 show a sketch of the Sumiyoshi Underpass. The Sumiyoshi Underpass was planned as a two-lane tunnel for vehicles, which was to cross under the railway tracks of the Yokosuka Line and the Tokaido Shinkansen Line at an angle of 70 degrees. The structure concerned is a single-story single-span box culvert structure with the following dimensions: 11.5 m wide, 7.7 m high and 31.6 m long. The Tokaido Shinkansen Line tracks were constructed on a girder-type elevated bridge built in the 1960s, and the foundation piles of the piers (P7 and P8) in the proximity of this crossing box culvert of RC structure were constructed using an earth drill method. The crossing structure for this project is located extremely close to the piers of the Tokaido Shinkansen railway tracks, with a minimal separation of 0.4 m, and the most significant issue of this project was construction in a manner that would not obstruct the normal operations of the Tokaido Shinkansen (Figure 4). Initially, we considered installing a temporary earth retaining structure in the proximity of the piers, cutting the ground and building an RC box, but concluded that it would be very difficult to apply this method because of probable excessive displacements in the Shinkansen railway piers. That is why we decided on the use of a non-open cut method in order to minimize the impact on the piers."

Jan 1, 2016

By R. Shields

"Hard rock mines move large volumes of material. But the conveyors essential to this movement suffer lots of problems, including carryback, spillage, dust, and belt wander. Many of these issues are created at the transfer points where the belts are loaded. This presentation will start with an overview of the latest transfer point systems that incorporate safety and serviceability by design. It will then report on recent projects. One project is the Conveyor B Transfer at the Coeur Rochester silver mine near Lovelock, Nevada. Here performance was improved with the installation of belt support cradles, engineered chute walls with external wear liner, and a compact dust collector. A second project is the improvement of belt support idlers and skirtboard sealing in a long loading zone of a conveyor under the concentrator at an Arizona copper mine. THE IMPORTANCE OF TRANSFER POINTS Conveyors are essential in mine material handling. Their performance will often make the difference in mine productivity and profitability. A key to conveyor performance are the transfer points where the conveyor belt is loaded and discharges. At these transfer points, many of the problems encountered with the conveyor system are created. The problems that arise at the transfer stations include off-center and segregated loading, mistracking, blockages and plugging. And there are a variety of problems originating with fugitive material—cargo released in the form of carryback, spillage, or airborne dust—that are created or exacerbated in the transfer points. These fugitive materials turn into other conveyor-related problems, including shortened component life, unplanned outages for conveyor maintenance, unexpectedly high labor costs for maintenance and cleanup, worker health and safety problems, and issues with community relations. As estimate attributed to the U.S. Mine Safety and Health Administration (MSHA) notes that 85 percent of conveyor maintenance is a result of fugitive material at conveyor transfer points. TECHNOLOGIES TO IMPROVE TRANSFER POINTS A number of techniques to improve the performance of conveyor transfer points have been developed. They include: • Absorbing impact, to prevent damage to belt, belt support systems, and conveyor structure, and reduce spillage caused by the impact energy arising from long material drops or large lumps of material loaded onto the receiving belt. • Stabilizing the belt line, to eliminate sag that allows spillage and encourages material entrapment that can damage the belt. • Protecting the skirtboard seals, by sheltering the sealing strips from the mass of cargo pushing material toward the edges of the belt. • Using self-adjusting, multiple-barrier edge seals, to keep material on the belt by providing long-lived seal efficiency with minimum maintenance requirements. • Controlling and centering the belt’s path, to eliminate belt wander and the spillage and damage it can cause. • Allowing dust to settle, through the incorporation of chutework that provides expanded stilling zone and the use of dust curtains at the points where the belt enters and exits the transfer. • Adding supplemental dust control systems, through the installation of systems for passive dust gathering, water-based dust suppression, and/or active dust collection."

Jan 1, 2017

By Shangyong Lin, Wei Sun, Weiping Liu, Muhammad Azam, Junfeng Chen, Yujie Zhao, David Asubonteng, Michael Ngoie

Copper concentrates are widely used in smelting operations worldwide and typically consist of chalcopyrite ( CuFeS2) as the primary mineral, with chalcocite ( Cu2S) and bornite ( Cu5FeS4) as secondary copper-bearing minerals. However, these concentrates often contain hazardous impurities, such as the fluorine ion, which can result in various complications during the smelting process. These issues include equipment corrosion, gas treatment requirements, environmental hazards, and strained community relations. Furthermore, high fluorine content in copper concentrates can lead to penalties and limitations during sales. To address these challenges, this comprehensive review assesses current techniques for removing fluorine from copper concentrate. Drawing upon recent research and the findings in the field, the review analyzes the advantages and disadvantages of existing fluorine removal methods and identifies critical issues requiring attention in the future. This review provides valuable insights into the current state of fluorine removal from copper concentrates and serves as a practical guide for researchers and industry professionals in this field.

Aug 2, 2023

By R. Benito

The publication of the Lerchs Grossmann paper in 1965 outlining a threedimensional graph algorithm for ultimate pit definition set the standard for the mining industry regarding pit optimization. Although the algorithm provides a solution from a static standpoint (i.e., assumes instantaneous mining), it is widely used for commercial packages to generate ultimate pit limits and intermediate phases. However, the solutions delivered are presented in canned reports lacking connection to the original data, which prevents further data analysis and extended reporting. The approach presented in this paper attempts to overcome such barriers by performing openpit optimization through databases. An adaptation of the Lerchs Grossmann graph algorithm is used to generate nodes, arcs and tree structures in customized tables to determine the maximum closure of a graph.

Nov 1, 2013

By M. L. Harris, J. Organiscak, S. Klima, I. E. Perera

"The National Institute for Occupational Safety and Health (NIOSH) Pittsburgh Mining Research Division (PMRD) conducted underground evaluations in an attempt to quantify respirable rock dust generation when using an untreated rock dust and a rock dust treated with an anti-caking additive. Using PDM 3600s and 3700s, these evaluations measured respirable rock dust levels arising from a flinger-type application of rock dust on rib and roof surfaces. Rock dust with a majority of the respirable component removed was also applied in NIOSH’s Bruceton Experimental Mine (BEM) using a bantam duster. The respirable dust measurements obtained downwind from both of these tests are presented and discussed. This testing did not measure miners’ exposure to respirable coal mine dust under acceptable mining practices, but indicates the need for effective continuous administrative controls to be exercised when rock dusting to minimize the measured amount of rock dust in the sampling device. INTRODUCTION Two factors have combined to renew concern regarding respirable dust measurements and compliance. This renewed recognition is due to two regulations that have modified operators’ rock dust schedules. First, the 80% incombustible requirement in intake entries has increased both on-section and outby-the-section rock dusting. Secondly, the recent respirable dust regulation change that has increased the number of respirable dust samples taken per sampling cycle. Previously, when only 5 samples were needed bi-monthly, rock dusting could be scheduled to not interfere with the respirable dust sampling schedule. The significant number of samples now required under new regulations combined with the need to maintain 80% total incombustible content in active mining areas require the schedules for respirable dust sampling and rock dusting to intermix. This raises concerns about the amount of rock dust that potentially is included in the sampler weight gain. Additionally, the respirable dust maximum was lowered from 2.0 mg/m3 to 1.5 mg/m3 (effective August 1, 2016) increasing concern that rock dust contamination may be an issue. Currently, the acceptable practice is to apply administrative controls such as keeping the miners upwind during rock dust application or to schedule rock dusting during a maintenance shift when the number of miners present is lower. NIOSH’s research examining the quality of rock dust has led to the development of hydrophobic rock dusts."

Jan 1, 2017

By R. L. Grayson

Using powerful database management software, nested-field analysis and microanalysis of narratives have been made of West Virginia accident data, resulting in a new approach for targeting and prioritizing safety interventions by county, mine size, specific mine, job title, type injury, etc. and combinations of these parameters. The analyses have been useful in focusing training and discussion sessions on specific work problems, trends, conditions, and situations for targeted groups of miners. Application of the technique will be presented in this paper, along with comparisons of various mine performance measures.

Jan 1, 1997