Search Documents

By ?. ?ivkovic

The silicate slag and copper matte that are the byproducts of smelting copper in a reverberatory furnace contain SiO2, FeO, Fe3O4, CaO and Al2O3, and Cu, Fe and S, respectively. These components influence the oxide (Cuox), sulfide (Cusul) and total (Cutotal) copper content lost in the waste slag. This paper uses multiple linear regression analysis (MLRA) to determine the degree of influence. The results of calculations obtained using MLRA were compared to actual measured results and found to have a large degree of correspondence, with the coefficient of determination R2 = 0.975. These results indicate that slag composition and copper content in the matte influence the copper losses in the waste slag with a probability of above 97%. It was determined that, of the total copper content of the slag, 74% is in sulfide and 26% in oxide form, and that this ratio is not dependent on the slag or matte composition.

Jan 1, 2010

By J. L. Ellenberger, T. Miller

"A limestone mine in Ohio has had roof instability problems that have led to massive roof falls extending to the surface. This paper describes a collaborative study of these events undertaken by the National Institute for Occupational Safety and Health and the mine owners. The study focuses on the roles that weak, moisture-sensitive floor and weak bands in pillars play in a general instability that led to roof falls at this mine. The NIOSH Stone Mine Pillar Design software (S-Pillar) does not include analysis for weak floor or weak bands and recommends that when such issues arise they should be investigated further using a more advanced analysis. It is important to recognize that without the impact of the floor or weak bands, the calculated inherent stability factor for these pillars is within the recommended design range. Therefore, to further investigate the observed instability occurring on a large scale at the Ohio mine, FLAC3D numerical models were employed to help determine the failure mechanism. Roof-to-floor extensometers were also installed in the areas predicted to have further instability. This case study will provide important information to limestone mine operators regarding the impact of weak floor causing the potential for roof collapse, pillar failure, and subsequent subsidence of the ground surface. This recent case demonstrates that weak floor can be a significant factor in pillar stability and should be assessed during the design stage of the mine.To an area-wide failure (Zipf, 2001). In that case, it appears that the pillars had actually remained intact. However, moisture-related yield of the weak floor caused deformations which passed through pillars and into the roof, triggering roof collapse around the intact pillars (Esterhuizen et al., 2011). This previous case and the case presented in this study, while not identical, both demonstrate that weak floor and/or bands within pillars can be a significant factor leading to instability."

Jan 1, 2015

By F. G. Rinker

The world demand for metallized iron continues to increase, keeping pace with steelmaking requirements for lower cost hot metal. Virgin iron ore and in-plant oxide fines can be reduced to direct reduced iron (DRI) and hot briquetted iron (RBI). MR&E has developed an improved coal-based process for cost-effective production of either DRI or HBI. Starting with dry compaction, the process combines the latest technology for material preparation, rotary hearth furnace construction and environmental control. Coarse iron ore fines are blended with pulverized non-metallurgical coal to produce a highly metallized (>90%) product. This paper presents production and installation cost data based on operating and under-construction iron oxide reduction facilities.

Jan 1, 1999

By Pasi Latva-Pukkila

Underground rock drilling has gone through intense development during the last 25 years. Mechanization and hydraulics have greatly increased the efficiency of drilling and improved the environment of the drill operator. As the total economy has become more and more important, the development has resulted in greater overall economy in drilling. The latest evolution step is computerization of drilling equipment. Computerization has been applied to tunnelling jumbos, long- hole drilling rigs and bolting rigs. With today's technology computerization is the natural way to increase capacity and productivity of the drilling process. However, it is still impractical to implement total "robotic" drilling. In computerized drilling the operator's role continues to be vital in controlling the drilling process and in analyzing the effect of individual parameters on the whole excavation process. Today this is called "CAD" - Computer Aided Drilling.

Jan 1, 1989

By E. Stolarski

The circulating fluid bed (CFB) technology can proudly point to its history of more than a quarter of a century of commercial operations. Over 80 CFB units operate in aluminum calcining, coal combustion and gold roasting. This paper describes the invention of the circulating fluid bed and chronicles its development and evolution from calcining through coal combustion to gold roasting. It presents performance data of Lurgi's CFB units in operation and highlights the six gold roasting plants currently operating throughout the world.

Jan 1, 1998

By Ruipeng Qian, Pengfei Wang, Guorui Feng, XianJie Du, Jun Guo, Yuxia Guo, Tingye Qi, JinWen Bai

"A numerical modeling was conducted to describe the behavior of overlying strata on the longwall top coal caving face for exploitation of a 16.8 m thick coal seam. Three typical structural models, including the Cantilever Structure (CS), Lower Cantilever and Upper Hinged Arch Structure (LC&UHA), and Lower Arch and Upper Voussoir Beam (LA&UVB), were developed. Based on mechanical analysis of the different structures of the key strata, and considering the behaviors of the broken igneous rock strata, a method was proposed and applied to estimate the structures of the overburden strata. The results had been verified by a field micro-seismic monitoring test. The paper provides a foundational method to determine the shield loadings for the top coal caving longwall face.INTRODUCTIONLongwall top coal caving (LTCC) is a highly productive underground mining technology which has been widely applied to the exploitation of the thick coal seams in China and other countries due to its high efficiency (Ju and Xu, 2013; Ju, Xu, and Wang, 2011; Liu et al., 2009). In recent years, a large amount of research on mining pressure forecast, strata control, and mechanical equipment improvement of the LTCC technology has been carried out, which greatly advances the field application of the technology (Liu et al., 2009; Yu, 2016; Dou et al., 2014; Feng et al., 2011; Chen and Li, 2011; Yin, Yan, and An, 2008). In 2006, the LTCC technology was first applied to the exploitation in a 20 m thick coal seam at the Tashan Coal Mine in China (Yan et al., 2011). Ten years of mining at the Tashan Coal Mine has highlighted the importance of the support management in controlling the roof strata on the extra-thick LTCC face. The mining pressure is closely related to the structural features of the overlying strata and its movement laws (Yu, 2016; Dou et al., 2014; Feng et al., 2011). However, the distributions of three zones—caving zone, fracture zone, and deformation zone—on the fully mechanized caving longwalls changed significantly with the increase in thickness of the coal seam (Chen and Li, 2011). The behavior changes of the roof strata led to abnormal pressure in the mining face and resulted in the difficulty of surrounding rock control (Yin, Yan, and An, 2008; Liu et al., 2009; Yan et al., 2011; Gong and Jin, 2008). Therefore, the theoretical research focused on the behavior of overlying strata to reveal the laws of mining pressure has important theoretical significance and practical value.Many classical studies (Qian and Shi, 2003; Feng, 2010; Yu, 2015; Yu, Yan, and Liu, 2012) had been done to describe the behavior of overlying strata in the mining process. It has also been reported that magma intrusion causes an important effect on the surrounding rock, coal, and methane (Wang et al., 2005; Liu et al., 2007). On the one hand, the property and structure of the coal seam was obviously changed by the magma intrusion and resulted in a potential danger of a gas outburst during the mining process (Chen et al., 2012; Wang et al., 2014). On the other hand, the hard igneous strata and the joints occurred with the magma cooled, causing an abnormal behavior of overlying strata and resulting in a series of dynamic disasters during mining (Xuan, Xu, and Lu, 2014; Lu et al., 2016). In fact, many coal fields in China are intruded by igneous sill, including the Datong, Shuozhou, Huainan, and Xuzhou coal fields (Chen et al., 2014; Wu, 2011). The 3–5 coal seam at Tashan Coal Mine in Datong coal field is very thick and is intruded by a large area of layered lamprophyre rock. Face falls and shield failures occurred frequently during the face retreat."

Jan 1, 2019

By T. Owen

Not since 1917 has a foreign company developed a standalone, grass roots gold mine in Russia. With. Russia's political changes of the late 1980s, development of mineral prospects once again beckons foreign investors. In 1990, Cyprus Amax began aggressively searching for such an opportunity. Early in 1997, production will commence at the Kubaka gold project located in the Russian Far East, near the Arctic Circle. The Kubaka project is a 1,750-tonne per day open-pit operation that will produce more than 300,000 ounces of gold per year. This paper discusses the challenges of locating such a prospect, doing business in Russia, developing supply lines, identifying work force capabilities, gaining government approvals, securing financing, arranging for gold sales and ultimately building a facility in this arctic region.

Jan 1, 1997

By Ronald B. DeDiemar

It is generally held that cone crusher application technology is strictly an art and thus subject to the vagaries of emphirical and/or trial and error judgments. While this is basically true, certain factors have been identified which, when properly defined, can significantly reduce the element of chance. This paper will bring out these factors as well as pointing out other technologies available to predict and/or analyze cone crusher performance.

Jan 1, 1977

By Denis Tepavac, Mark Trim

Structural performance of fiber reinforced concrete (FRC) depends on its ability to carry tensile forces after cracking. Australian Standards AS5100-2017 and AS3600-2018 are the only available design standards that establish a test procedure to determine strength and toughness of an FRC in direct tension. Direct tensile testing of fiber reinforced shotcrete samples was performed to determine if the model and guidelines in AS5100/3600 were applicable to shotcrete; all previous testing was from cast samples. In addition to direct testing, micro CT-scanning was also performed. The paper presents tests performed, results, and how the tests could be used on future projects. In addition, a brief summary is provided of the guiding structural mechanics used for estimating residual tensile strength and test methods utilized to verify those estimates.

Jun 13, 2023

By Bryan Ulrich

Knight Piésold and Co. hosted its annual roundtable discussion on March 17, 2011 at the Stockman Hotel and Casino in Elko, NV. The theme for Roundtable 2011 was, ?High density tailings, paste, and filtered tailings,? although the topic may well have been subtitled, ?Don?t prematurely rule out any technologies before they are given their day in court.? Bryan Ulrich, Knight Piésold?s local representative, as well as Tom Kerr from Knight Piésold?s office in Denver, CO, were on hand to help facilitate the discussion. Ulrich and Kerr are senior vice president and president of Knight Piésold?s U.S. practice, respectively. The event played host to more than 30 attendees from several western states. Attendees included personnel from a dozen mining properties and various corporate offices. There were also attendees from manufacturing and specialist consulting firms who have been providing services to various high-density tailings, paste and filtered tailings operations worldwide. It may be noted that the term ?filtered tailings? is used in this discussion. Alternative terms, such as ?dry stack? or ?dewatered tailings,? should be avoided whenever possible, as such terms tend to give a false sense about the nature of the material since these materials typically still retain a significant amount of moisture.

Jan 1, 2011

By T. Veneroso

Comminution is the process by which rock or ore is reduced to a size where the liberation of the minerals is maximized without changing the chemical or physical properties of the rock. Comminution accounts for about 50% of all energy that mines use (Klein et al., 2018). Growing demands from stakeholders and shareholders for sustainable development and CO2 reduction will increase the need for energy-efficient comminution. Ores with different mineralogical characteristics, textures, strengths, apparent stiffness, and mass-specific fracture energies need to be processed with a specific, new, and efficient comminution technology to increase the production and profitability of mining companies. The adoption of crusher wear parts built with new materials, such as non-Hadfield manganese steel or synthetic materials or traditional manganese with wear-resistant components, could improve the efficiency of the crushers, reduce downtime, increase production, improve the desired P80 (the aperture through which 80% of the product will pass) product size distribution, and enhance mine safety.

Feb 1, 2023

By Dennis N. Poffenroth

One concern of the Mine Safety and Health Administration is the structural integrity of steel wire ropes used on mine personnel hoists and elevators. Failure of such ropes has resulted in loss of life and property. Although thorough and regular visual examinations are performed, hoist ropes may still fail from undetected internal wear, corrosion, and broken wires. To complement visual examinations, nondestructive rope inspection techniques have been developed to determine deterioration and removal criteria. The techniques use electromagnetic and permanent-magnet test instruments designed by a Canadian firm. This paper describes the operating principles, field and laboratory testing of these nondestructive testing instruments, and discusses the feasibility of using this type of testing as a supplement to visual examination and destructive tests.

Jan 1, 1983

By R. L. Bullock

For the past 30 years there has been a gradual evolution of mechanical excavating systems in underground hard rock mining applications. This paper traces many of the tests of various tools and methods to break hard rock, up to the present. The tools include impact hammers, boring machines, disc on boom mining machines, disc on revolving wheels and drums, picks and drag bits on revolving hubs, rock splitters, slot cutting systems, and with customized explosives/powder mini-blasting. While the progress has been slow, successes are being achieved in hard rock and more opportunities exist today than ever before.

Jan 1, 1995

By Xianyang Qiu, Xiuzhi Shi, Chen Xie, Xiaofeng Huo, Yanhai Wang

In upwards medium-deep hole cut blasting, many confinement effects exist due to the small number of free surfaces, which is mainly provided by an empty hole. If the cut blasting effect cannot meet expectations, then subsequent blasting construction will be seriously affected, and large security risks to operators in the stope can be induced. The number of free surfaces is directly related to the layout of the cutting borehole. Therefore, it is necessary to optimize the layout of the first round of cutting boreholes. Theoretical analysis, numerical simulations, and field tests were used to study the formation process of cut blasting and optimize the layout of the first round of cutting boreholes. Based on the blasting parameters in the field, LSDYNA software was used to establish cut blasting models with four kinds of borehole layouts in the first round. The RHT constitutive model was used to simulate the rock-breaking effect. The numerical results show that the cut blasting effect is optimal when Nos. 3, 5, 7, and 9 are charge holes and Nos. 1, 2, 4, 6, and 8 are empty holes. In addition, the greater the number of empty holes, the larger the release space and the better the cut blasting effect. The uniformity of the empty hole distribution, namely, the uniformity of the release space, also affects the cut blasting effect. The field results indicate that a good cut blasting effect can be achieved by optimizing the borehole layout.

Sep 7, 2023

By Yashar Pourrahimian, Magreth S. Dotto

Fragmentation by blasting is a critical process in hard rock mining. The blasting process and outcomes are highly influenced by rock mass properties and their response to higher stresses and loading rates. Each rock mass is unique, but some features affect the blast energy similarly, leading to similar outcomes. Having analyzed these features and their influence on blast results, they can be incorporated into the blast design to achieve better outcomes. This paper presents a numerical model validated by a case study from the actual mine blasts that studied the effect of rock mass properties on explosive energy production, attenuations, and overall blast outcomes. The results show that when the model parameters are calibrated based on real data, they can be used to simulate the fragmentation process and therefore be used to aid blast design.

Jun 25, 2023

By George E. Edwards

Pacific Rim markets for export coal already represent a larger market than the total tonnage imported into the European Community countries and they will continue to expand. The largest importers will continue to be in the sector comprising Japan, Korea, Hong Kong and Tai- wan. It is likely that the total Pacific Rim markets will reach 206 m.t.p.a. by 1990 and 290 m.t.p.a. by 2000, with the major growth in steam coal demand. Australia has an efficient coal industry, represents a stable long term source of supply and is favourably situated geographically to continue to be the largest single supply source.

Jan 1, 1982

By Stephen J. Swan

Feed-forward control (i.e. the forward flow of information in a control system ) is a simple and flexible approach to over-all control of a ball mill-rake classifier grinding circuit. The system described here uses mill power, feed rate, mill dilution water flow rate, and classifier dilution water flow rate only, to control mill load, throughput, mill solids, and classifier solids as well as classifier overflow grind. The mill load is controlled by a simple feed-back control loop, while mill solids and overflow grind are controlled within close limits by a unique non-linear feed-forward water control system. In effect the control follows a limited mathematical model of the grinding circuit. The configuration minimizes deviations in overflow grind due to changing ore conditions, but since it is open-loop, and the model is not complete, it is affected by changes in total ball charge and liner wear. These effects are fortunately gradual, and changes in the grind can usually be kept to within ± 1% of a target continuously for several days without adjustment. Control adjustments are made with feed-back from laboratory composites. This control system has won enthusiastic operator acceptance; it is easily started up and shut down; grind-outs have been eliminated along with flotation machine flooding and mill spills. Standard measurements and components are used throughout providing a trouble-free system design at a moderate cost.

Jan 1, 1970

By L. Xinguang

Shandong MinMetals Corporation, a state-owned import and export organization located in the city of Qingdao, Shandong Province, China, was opened in 1954, with the mission of marketing metal products and industrial raw material in oversea areas for hard currency to support the modernization project of the country as well as the province. The management officers are appointed by the provincial government, and report to the Foreign Trade Department of Shandong Province. Meanwhile, the company also receives guidance from MinMetals head office in Beijing, the capital city of China. The head office does not own and control any provincial MinMetals organizations, but merely coordinate business among provinces.

Jan 1, 1990

By R. Y. Wan

Newmont Gold Company has advantageously used the capabilities of mineral oxidizing bacteria to develop a process for pretreatment of low grade sulfidic and carbonaceous-sulfidic refractory gold ores. The biooxidation process results in the oxidation of the sulfidic minerals with increased exposure of gold for subsequent gold recovery. The biooxidized carbonaceous-sulfidic ores cannot be heap leached with cyanide because of the "preg-robbing" characteristics of the carbonaceous matters in the ores. An alternative heap leach process using ammonium thiosulfate was developed to extract gold from the "preg-robbing" biooxidized ores. The ammonium thiosulfate leach process has been successfully practiced both in laboratory and pilot plant testing. Satisfactory test results encourage the continuation of process development.

Jan 1, 1996

By A. L. Hauff

As US Coal producers are looking more and more to the international markets, they face the complex job of planning and managing transportation logistics which make effective use of production capabilities, considers the various contract requirements to be fulfilled, Train, Truck and Vessel capacities, port restraints, etc. Pulling all the necessary pieces of information together to allow proper planning throughout the supply chain is often a time consuming, manual but necessary task. This paper will discuss the various constraints, requirements and considerations to supplying coal to a global market.

Jan 1, 2012