Search Documents

By Jeffrey K. Whyatt

The Crandall Canyon accident investigation included an interesting and unexplained observation by rescuers that the ?barrier rib had shifted northward as a unit, as much as 10 feet.? This is not the first mention of such a movement, although such reports are rare. Historical accounts describe unusual movement and displacement of intact coal, cribs and timbers. Two movements of particular interest are the creation of gaps above coal pillars and falling of standing support elements without apparent damage. A dynamic boundary element program was used to explore movements induced by slip on geologic features removed from the affected panel. While the resulting models are much too simple to fully replicate these observations, they do show that the types of phenomena observed are possible. They can also provide insight into the types of motions that ground support elements are subjected to during large bump events. This was demonstrated for the case of a large bump in a Book Cliffs coal mine. Seismic information suggested the source mechanism to be normal slip on a fault. A model of that source showed initial dilation of the panel followed by dynamic compression and rebound ? consistent with underground observations. The initial dilation is important as it may allow slender standing support to shift or fall.

Jan 1, 2009

By Khosrow Badiozamani

Operating mines in Wyoming and Montana, which are generally characterized by shallow overburden and thick coal seams, are faced with reclamation problems which are unique to this area. Unlike the eastern or midwestern mines, removal of thick coal seams and lack of sufficient overburden creates overburden deficiencies that require careful evaluation prior to mining to insure compliance with regulatory requirements. Computer models and computer graphics can assist in such evaluation where appropriate alternatives can be selected which satisfies both the regulatory requirements and minimizes cost. This paper presents one such model used in evaluation of backfill requirements for restoration of surface and ground water regimes, restoration of mined-out areas to the approximate original contour, and the blending of the mined-out areas to the surrounding topography.

Jan 1, 1981

By Z. Sample

"INTRODUCTION This past year commodity prices continued their dip with increased volatility causing market values to slide another 16% putting increased pressure on even the largest companies to improve their free cash flow.[1] Without a recovery in commodity prices in sight, companies must find a sustainable method to improve returns in the current economic climate. In an effort to improve plant sustainability, the mineral processing industry is investing in advanced automation technologies and innovative processing methods that are both more reliable and more efficient than ever before. One such breakthrough technology is Heap Leaching (HL). This method of extraction has certain advantages over traditional metallurgical methods making previously unsustainable operations economically feasible. While HL is already seeing use in the gold and copper industries among others, recent developments may allow for the use of HL to process primary sulfide ores which make up about 80% of today’s ores.[2] For this reason, this emerging technology is poised for exciting growth. Unfortunately, as with any process change, the implementation of HL projects requires significant training on both the control system as well as the underlying process, and further, due to the complex nature of the HL process, this can be a particularly difficult task. DEMOGRAPHIC TIME BOMB Even before the implementation of these new technologies, the availability of the skilled workforce has already become a significant problem for the mining and mineral processing industries. From a survey of 912 mining professionals, Stratum International found that a mere 0.4% of senior level candidates were between the ages of 25 and 34 and a similar proportion aged over 75 years.[3] This indicates that there is both a deficiency of young skilled workers and a skilled workforce that is retiring earlier than the previous generation. Combined with data published by the US Department of Labor stating that the median age of the mining workforce is approaching 50 years old, research suggests that up to 50% of skilled mining and mineral process professionals are expected to retire in the next 5 years, leaving with their irreplaceable knowledge and experience.[4] While it is projected that the labor pool will be sufficient to fill open positions, the real question is if this young workforce will have necessary skill sets and experiences. In addition to a rapidly aging workforce and an inexperienced labor pool, a study done by the Oil and Gas Journal showed that it takes about 7 years, on average, for new workers to achieve a level of competency that permits them to assess risks and appropriately make decisions.[5] Not only is this figure is in direct conflict with the typical tenure of 5 years in one position meaning that the thinly spread skilled labor will be required to become senior staff before they are able to achieve competency in their current role, this also means that these millennials are not given the opportunity to become competent in their role before the retirement of the more experienced workforce."

Jan 1, 2016

By W. G. Prast

Investments in fuel minerals and non-fuel minerals by petroleum companies are not a new phenomena. During the past 25 years, oil firms have entered mining via the acquisition route as well as by the direct development of grassroots mines. In the early 1980s, the "merger mania" in the natural resource industries came to a head. Oil company takeovers of mining firms, as well as other mergers between oil producers, captured headlines repeatedly, and speculation ran wild as to who would next acquire whom. Table 1 summarizes leading mining company mergers in the past two decades. There are some special features to the latest round of minerals investments undertaken by oil companies. First, direct takeovers of mining companies have become the preferred means of entry into minerals, with entry from scratch being relegated to the sidelines. This was not always the case. While there are instances of oil firms buying coal and copper companies dating back to the 1950s and 1960s, most of the early minerals work by petroleum firms was from internally generated projects. When the oil companies first became involved in uranium, for example, the uranium mining industry was in its infancy. There was not much market structure to buy, and it was relatively easy for everyone to get into uranium on the ground floor.

Jan 1, 1983

By C. C. Clark, D. J. Benton, J. B. Seymour, L. A. Martin

"The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting research on jackleg use and related accidents in underground metal mines. This paper provides an analysis and overview of jackleg drill usage, accidents, operational characteristics and alternatives, based on information from injury reports, legacy research, stakeholder input and published literature. The results indicate that jackleg drills are involved in more groundfall accidents in underground metal mines than any other drill, and jackleg-drill-related injuries are most prevalent at the face in the course of installing initial ground support. Practical mechanized alternatives to jackleg drills for drilling and bolting under incomplete support in narrow underground openings have not yet been realized. Small, versatile mechanized bolting equipment needs to be developed to address jackleg-drill-related accidents and improve safety at mines where jackleg drills are being used. IntroductionJackleg drill is a generic name for a handheld, rotary, percussion rock drill equipped with an attached reaction leg to provide stability and thrust (Fig. 1). All of the drill and leg controls are located near the operator’s handle at the rear of the head portion of the drill. Jackleg drills are classified according to the bore size of their pneumatic pistons, which normally range from 6.03 to 8.26 cm (2.375 to 3.25 in.) (Kurt, 1982; Clark, 2012). Jackleg drills typically weigh 46.7 kg (103 lb), but the weight can approach 54.4 kg (120 lb) after being fitted for operation with drill steel and air and water hoses (McKibbin and Clark, 2001). In underground mines, jackleg drills are commonly used to drill 3.8-cm (1.5-in.) diameter holes up to 1.83 m (6 ft) deep in rock."

Aug 1, 2016

By Robert J. Henning

The term olivine was first used in 1790 by J. Werner, and the corresponding mineral was so named because of its olive-green color (Hunter, 1941). Olivine is the principal component of the rock known as dunite. While by classic definition dunite is composed of 90% or more olivine, commercial use of these terms has resulted in more specific definitions. Commercially, the term olivine is used to designate a material that consists of 85% or more forsterite and contains 45 to 50% MgO, 39 to 42% SiO2, 5 to 8% Fe2O3, and has an ignition loss (LOI) of 1 to 2%. The term dunite designates a rock that contains 36 to 45% MgO, 36 to 39% SiO2, and has an ignition loss of as much as 10% (Teague, 1983). GEOLOGY Olivine is found in basic igneous and basic metamorphic rocks whose age varies from pre-Ordovician to Tertiary. Economic deposits are of magmatic origin and are restricted to the dunite variety of the peridotite group of ultrabasic igneous rocks. Olivine also occurs in basic igneous rocks such as gabbro, basalt, and diabase and more rarely as an accessory mineral in granite and metamorphosed crystalline limestones. Mineralogy The term olivine refers to a group of orthosilicate minerals in isomorphous series with magnesium-rich forsterite (Mg2Si04) as one end member and iron-rich fayalite (Fe,SiO,) as the other. In most olivines the ratio of magnesium to iron varies from 16: 1 to 2: 1. Commercial olivine deposits contain a mixture of forsterite and fayalite with the fayalite content restricted to less than 15% (Reed, 1959; Teague, 1983). Accessory constituents may include primary minerals such as ilmenite, magnetite, diopside, chromite, and garnet and secondary minerals such as chlorite, serpentine, talc, and vermiculite as alteration products. Chemical and Physical Properties The chemical composition of olivine can be expressed as either (Mg, Fe), SiO, or 2(Mg, Fe)O.SiO,. Table 1 presents chemical analyses for some commercial olivines. The physical properties of olivine are shown in Table 2. Distribution of Major Deposits Commercial olivine and dunite deposits are found in Norway, Japan, Spain, India, Italy, the United States, Sweden, Austria, Pakistan, and Mexico. Noncommercial deposits have been reported in New Zealand, Zimbabwe, South Africa, New Caledonia, Greece, Brazil, and Canada (Teague, 1983). The present markets for olivine are characterized by low unit value, high volume, and high sensitivity to freight costs, so few deposits are commercially viable. Literature from the USSR indicates that considerable research on olivine refractories is being done. (Afansa'ev, 1988), lending credibility to the conjecture that commercial deposits are being mined there. In eastern Canada synthetic olivine is being produced by calcining chrysotile asbestos mine tailings. In the United States numerous lenses of olivine extend in a belt from northeast Georgia northeastward across western North Carolina. Total reserves in North Carolina and Georgia are estimated at between 125 and 200 Mt. The largest US deposit is Twin Sisters Mountain, located in Whatcom and Skagit Counties in the state of Washington. This deposit, which has an outcrop area of 93 km2 and a relief of about 1 525 m. is estimated to contain 1 800 Mt of fresh, unaltered olivine (Teague, 1983). In addition, the US Bureau of Mines reports reserves of 50 Mt on Cypress Island in the state of Washington, and the literature reports eight complexes in southeastern Alaska, some containing cores of olivine as large as 1.6 km in diameter (Taylor, Jr., 1967). The world's largest deposit of olivine occurs in the Aaheim area of Norway, where reserves are estimated at a 2 000 Mt. Several other Norwegian deposits contain as much as 5 Mt each. In Japan the production of ultrabasic rocks is currently about 6 Mtpy, but the bulk of this output is serpentinite. Olivineldunite accounts for only 17% of this production. The major olivine deposit in Japan is located at Horoman Hill on the northern island of Hokkaido. Reserves at this deposit are estimated at 100 Mt (Anon., 1990). Spain is one of the largest producers of dunite. Reserves in the La Coruna District in northwestern Spain are estimated at 100 Mt. India, also a major dunite producer, has a large deposit at Salem in Tamil Nadu. In Italy olivine/dunite is mined from a deposit near Turin. In Sweden the largest deposit is at Arutats and is reported to be comparable in size to the Twin Sisters deposit in the United States. At present the only production in Sweden is from a deposit 30 km south of the town of Gallivare. Reserves at this deposit are reported to be between 1 and 2 Mt. Other significant deposits are: 1) in Austria at St. Stefan near Leoben, 2) in the Swat District of the North West Frontier Province in Pakistan, and 3) in Mexico at Cuidad Victoria in Tamaulipas (Anon., 1990).

Jan 1, 1994

By I. H. Warren

The high temperature lubricant molybdenite, MoS2, is usually produced by a complex sequence of processes involving mineral dressing of molybdenite concentrates followed by leaching with hydrofluoric acid to remove abrasive impurities such as silica (1). Many attempts have been made, mostly by techniques involving, direct fusion of molybdenum compounds with sulphur, to produce synthetic molybdenite. However, apart from some experiments of geochemical interest (2) in which aqueous solutions of sodium sulphomolybdate, Nat MoS4, were decomposed under pressure at temperatures between 300°C and 700°C, no attempts to produce the mineral by hydrometallurgical procedures have been reported. Since molybdenite is nominally a compound of tetravalent molybdenum with sulphur, and the most common state of molybdenum is +6, production of molybdenite is likely to involve reduction and sulphidization. The present study, therefore, describes the reduction, with hydrogen and carbon monoxide, of molybdenum in the hexavalent state in alkaline aqueous solutions containing sulphide ion. In these

Jan 1, 1972

By Thomas M. Larimer

Prior to April, 1961, the coal charge to Clairtonts coke oven batteries was 3" x 0" mine waslied coal having approximately 6.0% to 7.0% moisture. Even at this size and moisture content, the arching, rat-holing and hang-up was excessive and the effective live storage of coal was only 60% to 70% of the rated capacity of the coal bunkers, depending upon the moisture of the coal. In addition, many production delays were encountered in the time and methods required to fill the larry cars. The need for an improved metallurgical coke led to the introduction of pulverized coal to a portion of the plant in 196 1. When the full potential of the pulverizing equipment was realized, we were able to serve seven batteries in our second unit of batteries with pulverized coal through two coal bunkers. The discharge hoppers of these bunkers were equipped with air vibrators to assist the flow of pulverized coal into the larry cars. The vibrators were helpful in this respect but required considerable maintenance and caused damage to the bin plates.

Jan 1, 1968

By S. Crewdson

Vertical hoisting of materials using hoists and skips is common in the Mining Industry. These systems have a number of drawbacks, one being limited hoisting capacity at medium depths. FKC-Lake Shore and Metso Flexowell have been developing and installing vertical belts for medium depth shaft applications for many years, progressively going deeper whilst increasing belt capacity. The latest development from Metso the Pocketlift® belt advances this technology allowing higher tonnages to be lifted from greater depths. The design, manufacture, installation and operational experience of a 1818 tonnes capacity, 273 meters vertical lift Pocketlift® system at the White County Coal Pattiki 2 mine is the subject of this work.

Jan 1, 2003

By Panshi Xie, Yingyi Zhang, JIANJIE DUAN, Shenghu Luo

A multi-layer gangue roof of a steeply dipping coal seam with a large mining height face area was analyzed using physical simulation, numerical simulation, theoretical analysis, and field measurement methods to evaluate the roof deformation and the mechanisms associated with the instability of the hard gangue and soft coal interlayer. The results indicated that the first weighting step of the multi-gangue roof was larger than that of a non-gangue roof, but periodic weighting steps were similar. The overburden collapse height was lower in the multi-gangue roof than in the non-gangue roof due to the buffering and supporting function of the collapsed gangue. Moreover, the failure of the coal interlayer was the key factor in the collapse of the multi-layer gangue. A mechanical model was established for the hard gangue and soft coal interlayer based on a revised Prandtl squeezing theory. The limited load of the interlayer and maximum resistance of the shield support was thusmodeled. The maximum resistance of the support increased with the dip angle of the seam and burial depth. It also increased with the interlayer thickness at thicknesses below 2.75 m. It reached a peak when the interlayer thickness was between 2.75 and 3 m and exhibited a decreasing trend when the thickness was greater than 3 m. The results were confirmed using physical simulation and a field test. Certain measures were proposed to control the stability of the gangue roof, including zoning control of the mining height and resistance and advancing the support while maintaining roof contact, thus ensuring the integrity of the support and surrounding rock system.

Jun 30, 2020

By Mahaboob Basha Shaik, Shakuntala Tudu, Indrajit Paul, Chandra Sekhar, Neha Gupta, Amit Kumar, Srinivas Dwarapudi, Arvind Kumar Patel

In this study, the effect of colemanite and calcined colemanite (CC) addition on the properties of iron ore pellets is studied. The pellets are prepared in a lab without and with 0.2% colemanite and varying amounts of CC from 0 to 1.0 wt%in steps of 0.2%. A reference pellet is prepared under typical plant conditions, and the properties of the reference pellet are considered as the base value for improving the cold compressive strength (CCS) while maintaining the other parameters at an acceptable limit without altering the pellet. The study also aims to provide a detailed characterization of colemanite and calcined colemanite to better understand their behaviour during firing. The lab-scale results show that the CCS of pellets made with 0.2% colemanite was reduced by 222 points (60%) as compared to the reference pellets due to crack formation during firing. The results show an improvement in the CCS of the indurated pellets with CC dosage up to 0.4%, and decreasing strength is noted thereafter. It is observed that the swelling index increases with the increase in calcined colemanite dosage. To simulate plant conditions, reference pellets and pellets with optimized CC dosage were fired in a plant furnace.

Oct 16, 2020

By Teena Redhorse, David Tsztoo, Anthony Yu

"Since ancient times, storing and conveying water via underground water systems and tunnels has been touted for its strategic advantages. Underground cisterns and tunnels assured protection of essential fresh water supplies from man made contamination and especially from enemies who would gain an advantage by disrupting an adversary’s water supply in a siege. Modern day engineers do not usually specify tunnels for reasons of avoiding deliberate contamination or siege — however, they are just as enamored with the idea of building tunnels for water conveyances.Such was the case for the San Francisco Public Utilities Commission (SFPUC). The SFPUC provides drinking water to 2.6 million residential, commercial and industrial customers in the San Francisco Bay Area. The SFPUC’s water system includes 257 km (160 miles) of transmission pipelines and tunnels from the SFPUC’s largest reservoir, the Hetch Hetchy Reservoir inside Yosemite National Park, to San Francisco. About 129 km (80 miles) of the system consist of tunnels. A 30-km (19-mile) section of the tunnel network, called the Mountain Tunnel, was thought to be at risk of a catastrophic failure in its concrete-lined section of 18 km (11 miles). For much of the project planning process, a new replacement tunnel was presumed to be required according to the tunnel planners.Originally constructed between 1917 and 1925, the Mountain Tunnel has been in continuous service since 1925. The 30-km (19-mile) tunnel is located downstream of the Hetch Hetchy Reservoir water source in Yosemite National Park, between the Early Intake and Priest Reservoir (Fig. 1). Approximately 18 km (11 miles) of the tunnel is lined with unreinforced concrete. Though the condition of the tunnel was being monitored through water sampling and periodic inspections, there was growing concern that the tunnel lining was at risk of a partial collapse that could interrupt water delivery for up to nine months. The SFPUC was faced with a decision to construct a new bypass tunnel to replace the lined section of the Mountain Tunnel or to rehabilitate the existing tunnel."

Jan 6, 2018

By Xie Longshui

INTRODUCTION The gold production is from the state-owned gold mines, the local gold mines and the by-product of metal mines. Since 1975, the small gold mines have developed in rapid strides. Currently, there are about 3000 small gold mines in China. Most of them are operated by the local, and the production is about 50% of China's gold output. In the small gold mines, the normalized mining equipments are employed at most of mines, but some mines still use such backward tunnelling and mining tools as pick, shovel and hand hammer etc.. The mining techniques have developed from the primitive to the advanced, especially the methods of open stope, shrinkage and filling have been widely used. Such new mining techniques as bolting, vibrating draw, non-electric ignition and diamond drilling etc. are also introduced in the wall gold mines. In recent years, the development of small gold mines is very fast under the guidance of new mining policy which is ' rapid and great development of large-sized mines, helping small mines to develop, and quick mining for the existing mines; and encouraging the collective and the individual to operate a mine.' GEOLOGICAL FEATURES The gold veins are dominant, which are divided into two types, ie. the mesothermal deposit with altered rock in a crushed zone and the hypothermal deposit with quartz veins. The orebody distribution is not centralized, and the size of deposit and single minable orebody is small respectively. Most of deposit dip at 30° to 50°, characterized by expansion and shrinkage, ramification and compound, thinning out and reappearance, separation and composite at the parallel veins etc.. The ore grade is variable, and the factor of grade change is above 100%. The waste zones with lean or submarginal ore usually exist in deposits. As for the gold deposits with altered rock, the ore boundary is indistinct. Most of gold deposits, particularly the gold deposits with altered rock, are intruded by the late structural rock, thus the faults and joints are developed, and the rock and ore are crushed, especially the host rock of roof wall is very crushed. It ie obvious that the conditions of both formation of deposit and mining are considerably complicated. HISTORY With a long mining history and rich experiences, the local gold sectors are small, but they play an important role in China's gold mining industry. Dated from Xia and Shang Dynasty, the gold goods was made. In the Tang Dynasty, the development of gold mining industry was very fast. A Chinese poem , written by Liu Yuxi -- one of famous poets in the Tang Dynasty, says: As sun is shining over Dengzhou land, The fog on river slowly goes away, The panning girls together meet at bay, The beauty's jewels and stamps of king are gold from river sand. This poem shows the local gold mining was flourishing at that time. In 1888, the local gold mining sectors were all the rage at the moment, and the annual output of gold was as high as 21.5 tons. Since the founding of New China, the development of local gold mining was subjected to several back- sets, but certain advances are made on the whole, especially since 1970. Round about 1970,the simple, backward and indigenous mining was dominant in the small gold mines; for instance, the hand-hammer drilling, the hand-operated winch hoisting and the hand haulage etc.were main methods of gold mining . Up until the late 1970s,great changes took place in stoping, haulage and so on. Currently, some advanced technology and large-sized equipments are adopted in the local gold mines. Generally, the local small gold mining sectors play an important role in development of China's gold mining industry, and are important and attractive sectors. PRESENT DEVELOPMENT

Jan 1, 1987

By Michael W. Glasson, Archie M. Richardson, Leo Gilbride, Laine Adair

Andalex Resources, Inc. recently engaged in a ventilation planning exercise that resulted in the construction of a new main fan installation to support longwall coal mining at the Aberdeen Mine. This paper documents the planning process, including underground measurements, modeling, permitting, and construction of the new fan installation.

Jan 1, 1997

By Barrie W. Sullivan

The New Celebration Gold Mine near Kalgoorlie in Western Australia was commissioned in late 1986 and the CIL treatment plant currently processes 1.7 million tonnes of gold ore annually. The 1988 geological resource was 13.2 million tonnes grading 2.37 g/t Au in several open pittable deposits with the bulk of gold mineralisation occurring as a stockwork in Archaean quartz feldspar porphyry intrusives along a major regional shear zone. Mine planning, scheduling and operating techniques have focused on minimising open pit dilution whilst maintaining production requirements. This paper describes the successful achievement of this aim in extremely variable ground conditions and orebody widths.

Jan 1, 1989

By Robert W. Holliday

Natural resources are the reservoir from which society draws its material sustenance. Although there is a growing awareness of the need for aesthetic resources such as space for recreation and natural beauty, the basic resources are soil, air, water, and minerals including fuel. Minera's and all sources of energy gain in relative importance with advancing technology and expanding industrilization. In the highly industrialized economy of the United States, almost every aspect of man's life is touched in some way by a product of, the mineral; industries. Agriculture owes much of its productivity to mineral-based fertilizers, insecticides, and mechanical equipment. Modern construction, manufacturing, communications, and transportation are all dependent on nonmetallic minerals, metals, and fuels. Throughout history, those nations with access to minerals, and the technology for using them, have gained ascendency. Before World War II the leading powers also were, leading coal producers. In order of declining rank the five leading' coal producers were the United States, the United Kingdom, Germany, the USSR, and Japan. That the military victory went to the side with the greater' capacity to convert iron and coal into tools of industry, and weapons, is' more than coincidence. It is a fundamental' fact of existence. It is axiomatic that the United States must have a continually increasing supply of minerals if we are to meet the needs of our burgeoning population for a comfortable standard of living and for national security.

Jan 1, 1968

By XUEWEN WANG, Changda Zhang, Huaguang Wang, Mingyu Wang, Bin Hu

The copper smelting process produces plenty of copper slag every year, which is a hazardous solid waste, but a secondary resource. In the present study, the extraction of copper, nickel, and cobalt from copper slag was investigated through the process of sulfation roasting–water leaching and the process of sulfation roasting–sulfate decomposition roasting–water leaching respectively. Compared with the process of sulfation roasting–water leaching, the process of sulfation roasting–sulfate decomposition roasting–water leaching is a better choice, which could not only get almost the same leaching of copper, nickel, and cobalt as the former process, but has a lower leaching of iron and aluminum. For the process of sulfation roasting–sulfate decomposition roasting–water leaching, the leaching of Cu, Ni, and Co reached up to 74.2%, 71.1%, and 69.6% respectively, under the optimal conditions including sulfation roasted with 80 wt% sulfuric acid addition at 200 °C for 60 min and sulfate decomposition roasted at 650 °C for 60 min, followed by water leached at 90 °C for 30min with a liquid–solid ratio of 2 ml/g. The leaching of Fe and Al was only 4.9% and 17.6%.

May 4, 2020

By Nord L. Gale

Lead, zinc, copper, silver, cadmium and many other heavy metals which are potentially hazardous if released into the environment in wastewater discharges have been of considerable concern to governmental agencies, industry and the general public. In response to this concern, an interdisciplinary research team at the University of Missouri has been funded by the National Science Foundation-RANN program to study trace contaminants associated with the production of lead for the past eight years. Seven modern mines in close proximity to two lead smelters in the forested Ozarks of Southeast Missouri are the largest source of lead in the world and in 1976 alone produced 504,095 short tons of lead, 82% of the United States total production. This new and rapid industrial development in a sparsely populated. rural forest region has offered a unique opportunity for studying the impact of trace metals and for developing improved techniques to control detrimental effects. Research on the wastewater discharges and two methods of biological and recycle control are discussed in this paper. Although the two mine-mill complexes investigated in this study have many similarities, the differences between the two are substantive and warrant separate examination.

Jan 1, 1977

By A. P. Grobbelaar

Andalusite is a member of the sillimanite group of minerals consisting of andalusite, kyanite, and sillimanite. These minerals are the structural polymorphs of Al,Si05 (the anhydrous silicate of aluminium) and although chemically similar, they differ in physical properties due to their different crystal structures. For further information on the sillimanite group, see the chapter on Kyanite and Related Minerals that follows. The minerals are generally the products of the metamorphism of alumina-rich sediments and are found in schists, gneisses, or hornfelses, which have undergone either regional or thermal metamorphism from their original form. Sedimentary deposits may also form since the minerals are chemically and physically resistant to breakdown. When heated to a sufficiently high temperature the sillimanite group minerals convert to mullite with a resultant volume expansion and the liberation of silica. Due to the stability of the mullite formed, its high hot strength and resistance to chemical and physical erosion, they are widely used in the manufacture of refractories and special ceramics (Table 1). The reaction can be represented as follows: [ ] The worldwide use of these minerals depends to a large degree on their availability (Fig. 1). Andalusite, with its lower conversion temperature and the lowest volume expansion on being heated is the natural choice as a raw material to produce energy-saving refractories without prior calcination. The Republic of South Africa holds by far the largest minable andalusite deposits of the world, estimated at some 70 Mt of known in situ reserves. The only other large commercial production of andalusite comes from France, with known reserves of about 5 Mt. Potential new deposits are known from China, Ireland, Australia, and South America. World consumption of andalusite in special performance refractories has risen from less than 10 ktpy in 1960 to nearly 300 ktpy in 1990, which is due to cost effectiveness in many industrial applications compared to other conventional refractory products. Andalusite-based refractories have traditionally been used in Europe, South Africa, and the Far East; usage in America was limited in the past due to relatively high delivery costs and availability of other local refractory minerals. However, there is a significant trend towards greater use of andalusite in North America, thus opening new markets and replacing other traditional refractory raw materials. GEOLOGY Andalusite occurs in metamorphosed rocks of clay-like com- position, as in the andalusite-hornfelses in thermal aureoles (contact metamorphism), formed under conditions of high temperatures and low stress, and in regional metamorphic rocks, such as the andalusite-schists. These schists are mostly unconnected with definite igneous intrusions but were presumably also formed at high temperatures and under low stress. Andalusite can also appear in alluvial deposits associated with the primary deposits. At depths of 10 to 20 km, temperatures of up to 450°C might be expected. Another result of increasing depth is an increase of pressure due to the load of the rock cover. The load stresses involved in metamorphism is generally believed to lie in the range 0 to 10 000 bars. During contact metamorphism the increase in temperature is brought about by the injection of magma. The temperature reached in the country rock at some distance from the igneous body will always be less than the initial temperature of the intrusion, which is presumably less than 1 200°C, and will vary with time and distance from the contact. A simple metamorphic reaction involving dehydration of an aluminous sediment can be: [ ] At higher temperatures sillimanite would form at the expense of andalusite, while kyanite would be the mineral formed at higher pressures, as can be seen in the phase diagram of A12Si05 (Fig. 2).

Jan 1, 1994

By J. F. Peterman, M. C. Roberts

The success of any industrial mineral project requires an accurate forecast of the demand fir the material as well as accurate projections of costs and prices. This paper develops a general method of predicting mineral requirements and applies it to the case of graphite. The basic method is to explain graphite consumption in each of its major uses by the output and manufacturing technology of the using industry. Once these underlying factors are determined, they can he projected to establish future requirements. This forecast is critical to the evaluation of a new source of supply, such as the graphite resources of Upper Michigan.

Jan 1, 1990