Search Documents

By Joseph Clare

It’s not the 1960s anymore. Upgrading wastewater pipelines in the current era demands the latest trenchless technology to minimize impacts. King County Wastewater Treatment Division in Seattle, Washington is designing a nearly mile long Direct Pipe® influent sewer combined with microtunneling to replace a 1960s era trunk sewer constructed along and within Coal Creek and its natural area. Trenchless installation using Direct Pipe® and microtunneling was chosen due to reduce impacts to residential neighborhoods, natural creek environments, and the constraints of topography

Jun 13, 2021

By Y. J. Zhang

This paper presents the results of a recent study on the development of an in-situ testing method for determining the coal strength in mine pillars. The strength testing is performed in the horizontal holes drilled into the coal rib using the penetrometer. It is a hydraulically powered device that uses an indenter to press the surface of the borehole until the load reaches the failure point of coal. The pressure and the penetration of the loading pin are recorded by the data acquisition unit. The results collected from several coal mines indicate that this testing method is ideally suited for the realistic coal strength measurements. The new testing system not only improves the accuracy of pillar strength determination, but it is more cost efficient than the conventional method.

Jan 1, 1995

Global mining company achieves significant productivity gains with three-dimensional (3D) mine models developed with Abaqus finite element analysis software. In a steep change beyond traditional processes, Abaqus finite element analysis (FEA) software from Simulia (the Dassault Systèmes? brand for realistic simulation), is being used to enhance mine design and engineering simulation at a number of major mines around the world. In North and South America, Africa and Australia some of the world?s biggest mining companies are applying FEA technology to evaluate safety and improve design planning, implementation and operations. Beck Arndt Engineering (BAE), a Sydney-based international consultancy, is a pioneer in the commercial development of engineering solutions for the mining industry. The consultancy has worked closely with engineers at Simulia Australia to expand the use of Abaqus FEA simulation software for mining applications. Among the early adoptors of mine-ready FEA technology is the world?s largest miner, BHP Billiton. With BAE?s help, BHP has already applied this technology to evaluate mines in Canada and Australia. At the BHP Billiton Nickel West Perserverance Deeps Project in Western Australia, Abaqus FEA software is now being used to help engineer the safety and productivity of planned deep-mining operations. To achieve this goal in the deep-mining environment significant technological innovation is required. Using measurements of site deformation and seismicity, Abaqus FEA models have been calibrated and, in a single day, used to simulate a full, 3D, inelastic analysis of a mine?s life cycle. In recent years, similar applications at Debswana?s Jwaneng Mine in Botswana, the Newcrest Mining Ridge-way Deeps Project in New South Wales, Australia and Rio Tinto?s Argyle Diamond mine in Western Australia have also established Abaqus FEA analysis as the lead-ing technology for multi scale, simulation-aided mining engineering. Joop Nagtegaal, a pioneer of FEA and a Dassault Systèmes Corporate Fellow, said that Abaqus FEA software is unique in its capabilities to enable mining engineers to investigate design innovations from the drawing board to full production. ?In the design stage, Abaqus models, which include rockmass volumes spanning several kilo-meters around the ore body and down to excavations just a few meters across, are used to compare and optimize engineering options,? Nagtegaal said. ?Then, as the mine goes into production, large volumes of data from the field are incorporated with the analysis models to allow them to be calibrated to a precision not previously available to the mining industry.?

Jan 1, 2009

By Staff

"In 2018, the total estimated value of nonfuel mineral production in the United States increased by 3 percent from 2017 to $82.2 billion. The estimated value of metals produced domestically decreased by 4 percent, and the estimated value of indusrial minerals produced domestically increased by 7 percent (Table 1).Some idle U.S. metal mines and processing facilities restarted in 2018, including two primary aluminum smelters in Indiana and Missouri, a rare-earths mine in California and a zinc mine in New York. In contrast, four iron ore mines in Minnesota and a pelletizing plant in Indiana were shut down. Increased oil and natural gas drilling activity in 2018 led to increased production of some industrial mineral commodities that are used for oil and gas drilling, including barite and industrial sand and gravel. Production of industrial minerals primarily used in infrastructure and residential construction — including, cement, construction sand and gravel, crushed stone and gypsum — increased in 2018. Overall, mining activity trended upward for the second consecutive year because of increases in oil and gas extraction and industrial mineral mining (Table 2).Mineral industry performanceDiscussion of mine production is commonly segmented according to the type of materials produced within the broad categories of metals and industrial minerals (also known as nonmetallic minerals). Industrial minerals can be further subdivided as natural aggregates and other industrial minerals. Metals tend to have higher unit values but very low production quantities compared with those of industrial minerals, such as crushed stone or construction sand and gravel, which have higher production quantities but are lower-valued materials. Therefore, for discussion and analysis of the performance of the nonfuel minerals industry, the value of production is used rather than the tonnage produced. Tonnages of natural aggregates are orders of magnitude larger than those for most other mineral commodities, thus making direct comparisons based on weight meaningless (Fig. 1)."

May 1, 2019

By Earle Faig

Earle Faig Along with other transportation modes, the barge industry will be greatly affected by trends in domestic coal production. Traditionally, coal has been one of the major commodities moved by barge. Now, because of events in the international energy market, coal is finally getting the recognition it deserves as a major component of the country's energy program. Perhaps even more significantly, a series of events has caused other countries to turn to the United States as a source of coal. Although the outlook for coal demand is optimistic, it will be greatly influenced by the ability of the transportation sector to handle the additional traffic. Because of its long experience in moving large quantities of coal, the barging industry is in an excellent position to capitalize on coal's increased popularity. A brief description of the barging industry should facilitate the discussion of coal as it relates to that industry. Barge companies operate on a river system that is over 40 Mm (25,000 miles) long. It includes the East and West Coasts and the Mississippi River System comprised by the Allegheny, Monongahela, Kanawha, Ohio, Illinois, Missouri, Tennessee, Cumberland, Arkansas, Warrior-Tombigbee, and Mobile Rivers, and some smaller tributaries. The Gulf Intracoastal Waterway stretching along the Gulf Coast from Brownsville, TX, to Apalachicola, FL, also is considered part of the inland waterway system. Approximately 1,800 companies operate on the inland river system and have a combined fleet of about 4,400 towboats and 28,000 barges. The fleet of towboats represents 4.8 GW (6.4 million hp) of power. The towboats comprising this fleet vary in size from a small harbor boat to a large line haul boat with 7.5 MW (10,000 hp) of power. The choice of size and power of the boat depends on a number of factors, including the size of the river and operational constraints, such as lock size, river-current rate, and water level. The choice also depends on the tow size. A single tow on a river capable of locking through 15 barges at a time handles up to almost 20 kt (22,000 st), whereas a tow on the lower Mississippi, which has no locks, can accommodate up to 41 kt (45,000 st) of cargo. Because the quality of coal is not typically damaged by exposure to the elements, it is usually moved in open hopper barges, although covered barges are used occasionally. The most frequently used size is the jumbo barge that measures 59 m (195 ft) long by 11 m (35 ft) wide by 4 m (12 ft) deep and can handle up to 1.4 kt (1,500 st) of coal. Advantages of Barge Transportation Barging offers several inherent advantages in transportation of bulk commodities like coal. First, barges can carry large quantities of product. A single jumbo hopper barge can handle 1.4 kt (1,500 st) of cargo while it takes 15 91-t (100-st) capacity rail cars or 57 trucks hauling 24 t (26 st) each to move an equivalent amount of cargo. Thus, barges can move more tonnage with less equipment than competing forms of transportation. Second, barging offers the most fuel efficient means of transportation. Less energy is required to push a load over water than to pull a similar load over land. The amount of pollution attributable to barge traffic is minimal because barges consume less fuel. Third, barging is an inexpensive form of transportation. The inland waterway industry transports about 12% of the nation's freight for about 2% of the total freight bill. This can be attributed to competition between the large number of companies on the river system and competition with other transportation modes. Fourth, barging is an environmentally safe method of transportation. Inland river routes expose fewer urban areas to hazardous substances than rail or truck. And barge spills occur less frequently than rail or truck spills. The industry does pose some disadvantages. The waterway system is constrained by the natural river network, so barges cannot travel on the most direct straight-line route. This means that barging is usually an incomplete form of transportation requiring interface with truck or rail. The industry's market is limited to those geographical areas that are located on or near the rivers. In addition, it is a time-consuming transportation mode, making it impractical for many types of commodities.

Jan 10, 1982

By Vishnu S. Gupta

A modular computer program APEX (AMAX Process Evaluation Executive), has been developed at AMAX Extractive R&D, Golden, Colorado to facilitate rapid simulation of steady state material and energy balances of existing and/or proposed metallurgical process flowsheets. Currently, APEX is being used for the design, analysis, and evaluation of several of AMAX?s Nickel, Molybdenumand Tungsten processes. A unique feature of APEX is that it allows specifications of flow rates and compositions for different solid size fractions in addition to aqueous organic and gaseous phases. Thus, a metallurgical process which may involve crushing, grinding, flotation, leaching, washing, solvent extraction, precitation and refining operations can be simulated in a single computer run using APEX. APEX requires two input data files. The first is a process data file which includes physical and thermodynamic properties of the various chemical components of interest. This data file is unique to the process under study and does not require changes for alterations in the process flowsheet. The second data file is specific to a simulation case and includes descriptions of the flowsheet, various feed streams and the process equipment's operating conditions. In addition to temperature, pressure and percent solids, calculated information for each stream includes weight and volumetric flow rates, chemical compositions, specific gravities and enthalpies of solid, liquid and gas phases. For each process equipment in the flowsheet, APEX prints its operating conditions and detailed information about the streams that enter and leave the unit. Models of several general unit operations are preprogrammed in APEX. Also, the modular design of APEX permits quick and easy additions of simulation models which are specific to new and/or unique process operations. To study process stability and optimization, APEX permits several cases of a flow-sheet to be run together. Three simulations of the Moa Bay Nickel process have been excluded to illustrate the ease and flexibility of using the APEX system.

Jan 1, 1980

By A. Robison, V. T. McLemore

"The San Juan Basin, New Mexico contains many heavy mineral beach-placer sandstone deposits of Cretaceous age. Beach-placer sandstone deposits are concentrations of heavy minerals that formed by mechanical concentrations (i.e. settling) of heavy minerals on beaches or in longshore bars in a marginal-marine environment. They have high concentrations of several elements, such as Ti, Zr, rare earth elements (REE), Sc, Y, U, Th, Nb, Ta and Fe. These elements are becoming increasingly more important to industry, because they are used in the manufacture of devices our society uses every day, i.e. cell phones, computers, and alternative energy devices, like solar panels. It is unlikely that any of the beach-placer sandstone deposits in the San Juan Basin will be mined in the near future because of small tonnage, low grades, high iron content, and distance to processing plants and markets. However, as the demand for some of these elements increases because of increased demand and short supplies, the dollar value per ton of ore rises, enhancing deposit economics. Current studies at the New Mexico Bureau of Geology and Mineral Resources are focused on the Apache Mesa (formerly Stinking Lake) deposit near Dulce, New Mexico. INTRODUCTION Beach-placer sandstone deposits are accumulations of heavy, resistant minerals (i.e. high specific gravity) that form on upper regions of beaches or in long-shore bars in a marginal-marine environment. They form by mechanical concentration (i.e. settling) of heavy minerals by the action of waves, currents, and winds (Fig. 1; Bryan et al., 2007). Modern examples are found along the Atlantic Coast, USA (Koch, 1986; Carpenter and Carpenter, 1991), southeastern Australia (Roy, 1999), and Andhra Pradesh, India (Rao et al., 2008), where they are mined for titanium, zircon, and monazite (a Ce-bearing rare earth, REE, mineral). Detrital heavy minerals comprise approximately 50-60% of these sandstones and typically consist of titanite, zircon, magnetite, ilmenite, monazite, apatite, rutile, xenotime, garnet, and allanite, among other minerals. Most of these minerals have a high specific gravity exceeding 4 and are dark colored, giving the sandstones a dark color, resulting in them being called black sandstones. Although beach-placer sandstone deposits are found in strata of all ages; the deposits in the San Juan Basin in New Mexico are restricted to Late Cretaceous rocks belonging to the Gallup, Dalton, Point Lookout, and Pictured Cliffs Sandstones (Fig. 2; Table 1; Chenoweth, 1957; Houston and Murphy, 1970, 1977). The beach-placer sandstones are black, dark gray, to olive-brown, resistant to erosion, and radioactive due to radioactive zircon, monazite, apatite, and thorium minerals. Anomalously high concentrations of Ti, Fe, Nb, Th, U, Zr, Sc, Y, and REE are characteristic of these deposits. Similar Upper Cretaceous heavy mineral, beach-placer sandstone deposits are found throughout Montana, Wyoming, Utah, Arizona, and Colorado (Dow and Batty, 1961; Houston and Murphy, 1970, 1977; Zech et al., 1994)."

Jan 1, 2016

By Thomas V. Falkie

In bygone days, the mineral engineer spent most of his/her time on the technical aspects of designing, building, and managing mineral operations. In the last few decades, mostly since the 1960s, increasing amounts of engineering man power and time are spent dealing with federal, state, and local government agencies, laws, and regulations. It is not possible to plan, design, build, or operate mines, mills, smelters, or even office buildings without detailed consideration of government regulations and permitting requirements dealing with environment, worker health and safety, etc. The four chapters of this section provide an overview of the social, legal, political, environmental, and health and safety aspects of mineral enterprise. The section sets the stage for the working engineer/geologist in industry, government, consulting, or academe and points the direction for more detailed study in each of these areas.

Jan 1, 2008

By A. E. Halim, J. F. Brune

The 2006 Sago, Darby, and Aracoma mine disasters in the United States (US) forced the US government to implement the 2006 MINER Act and additional regulations that require all US underground coal mines to install and maintain refuge chambers to manage entrapment emergencies, in particular, fires and explosions. However, there is a debate on whether barricading in refuge chambers is a good strategy to survive such emergencies. Australian coal mines are not required to use refuge chambers and, instead, have adopted a strategy that focuses on instructing and training miners to self-escape to the surface. This paper analyzes merits and problems of using refuge chambers and self-escape to the surface to manage emergencies in fires or explosions in an underground coal mine. The authors found that the use of refuge chambers may not be the best strategy during extensive fires or when multiple explosions happen. In these situations, mine rescuers are unlikely able to extract miners who are sheltered in chambers and conversely, self-escape may save more lives than sheltering. Chances for successful self-escape are further improved by regular, externally assessed training such as Level 1 Emergency Exercises required in the Australian State of Queensland. These exercises put pressure on mine operators to ensure and maintain the effectiveness of their emergency management system.

By Jr. Smith

Borates have been mined in the desert areas of California and Nevada for more than 100 years. To about 1890, playa surface mining provided the chief sources of boron minerals. Underground mining of colemanite and later of borax and kernite was predominate until about twenty years ago. Open pit mining of the large deposits of borax and kernite near Boron, California has been most significant for the past twenty years. Mining of colemanite in the Ryan, California area, near Death Valley, began in 1907. Following the discovery of the large deposits in the Boron area (about 1957), mining in the Death Valley area became nearly nonexistent. Only small tonnages were mined for special uses. Little mining was done in the Boraxo area near Ryan. The first claim was made in about 1915 In 1960 the area became the property of the Kern County Land Company, which was acquired by Tenneco Oil Company in 1967. In 1976 the various borate properties and claims in this region were acquired by American Borate Corporation. The open pit mine is now approximately 400 feet (121.9 m) deep, 3000 feet (914.4 m) long and 1000 feet (304.8 m) wide. The borates in the Boraxo pit consist primarily of three minerals. These are about 50% coiemanite (C2B6O11' 5H2O), about 40% probertite (NaCaB5O9.5H2O), and 10% ulexite (NaCaBcO9.8H2O). The colemanite, along with boric acid and high-grade coiemanite ore from Turkey provide the only sodium-free borates for production of textile grade fiberglas. When heated to its decomposition temperature, colemanite decrepitates to a fine powder. This provides the basis for the concentration process. The gangue minerals in this deposit are primarily calcite and clays, including bentonite. The ore body has a very low arsenic content.which is a desirable feature. Test work had been done with samples prior to the results discussed herein. This paper will discuss results of test work which were the basis for erection of a plant, and the subsequent plant operations.

Jan 1, 1978

"A long-term mine production schedule optimization based on stochastic integer programming is presented that manages the risk due to geological variability and uncertainty while jointly considering mine profitability, truck fleet requirements and waste management. The evolution of the pit is controlled so that space within the mined-out pit is continuously provided to allow for tailings and waste rock to be replaced, thus minimizing the project’s environmental footprint. The method is applied at a taconite iron ore deposit and has a project net present value that is 16.9 percent higher than that of a conventional schedule and has a higher chance of meeting production forecasts. The stochastic schedule reduces equipment requirements by delaying waste mining and by mining selectively in order to meet plant ore feed requirements without stockpiling material, resulting in 23.7 and 26.2 percent lower mining capital and operating costs, respectively. IntroductionThe LabMag iron ore deposit is part of the Millennium Iron Range, a 210-km (130-mile) belt of taconite in northern Quebec and Labrador, Canada. LabMag has significant economic potential. It contains more than 3.3 Gt (3.6 billion st) of proven reserves at an average total iron content of 29.8 percent and is very low in impurities. However, on a project basis of 23 Mt/a (25 million stpy) of product, the required capital expenditure is estimated at more than $5 billion (SNC-Lavalin, 2014), which necessitates careful evaluation of all sources of risk. Resource estimation is one of the main sources of risk in a mining project as knowledge of the orebody is primarily based on drilling, which is often sparse because it is expensive. If the expected ore tonnages and qualities are not obtained when mining, the project cash flows are directly affected. The expected quantities and qualities of ore and waste are defined by the mine production schedule, which specifies the sequence of extraction and is dependent on the resource estimation. The goal of mine production scheduling is thus to maximize the expected profit, while also meeting all production targets and constraints, by creating an extraction schedule that is robust in the face of geological risk and has the highest chance possible of actually being realized."

Jan 10, 2017

By J. R. Sturgul

Computer simulation models of working mines can be of great benefit to the mining engineer. Such models have been used in mine planning (how many trucks/shovels to have, when to add new equipment, etc.), mine design (should a dispatch system be purchased, where is the optimum location for mine equipment, etc.). A simulation model can be thought of as a dynamic representation of the mine and can easily be changed to reflect a wide variety of different situation. Often a major problem for the engineer is how to present the results of the simulation study. Using PROOF(R) animation it is now possible to interface the results of the simulation and project them onto a computer screen in cartoon fashion.

Jan 1, 1993

By Ting Ren, Jon Roberts, Zhongbei Li, Ming Qiao, Jianming Wu

Spontaneous heating of coal continues to present a health and safety hazard in underground coal mines. The influence of seam gas composition on gas flow dynamics and distribution characteristics in the active longwall goaf has not been studied in-depth, and corresponding effective proactive goaf inertization strategies for preventing potential spontaneous heating from occurring have limited investigation. To advance this knowledge, an 80-m-height goaf model was constructed and developed based on specific conditions of an Australian underground coal mine, and onsite gas monitoring data was collated to verify base model results, which allowed for various scenarios of seam gas composition to be simulated and investigated with confidence. This study involved modeling five different gas composition scenarios for the goaf atmosphere, namely, 100% CO2 (case 1), 80% CO2 and 20% CH4 (case 2), 50% CO2 and 50% CH4 (case 3), 20% CO2 and 80% CH4 (case 4), and 100% CH4 (case 5). Simulation results show that O2 is primarily distributed at the middle and upper part of the CO2- dominant goaf model, while it is mainly layered at the floor level of the CH4- dominant goaf model. N2 is superior to CO2 in the goaf inertization for the CO2- dominant goaf model, whereas CO2 performs better than N2 for the CH4- dominant goaf model. The optimal inert gas flowrates for case 1 to case 5 are 1.5, 1.75, 0.75, 0.5, and 1.0 m3/ s, and the oxidation zone area is reduced by 55.76%, 67.21%, 58.04%, 78.17%, and 81.82%, respectively. The simulation results allow for increased insight and understanding of the gas distribution patterns in the active goaf with different seam gas composition and the development of corresponding proactive goaf inertization practices, thus minimizing potential spontaneous-heating-related hazards and improving mining safety.

Sep 26, 2023

By Aleksandar D. Bugarski, Dylan A. Ritter

The results of laboratory characterization of tailpipe emissions for three “clean” engines that meet U.S. EPA Tier 4 final emissions standards were used to assess the viability and effectiveness of repowering existing engines and powering new mobile equipment with those engines as a control strategy for reducing exposure of underground miners to diesel aerosol and criteria gases. The evaluated engines were representative of those that achieve the emission standards through implementation of various in-cylinder emissions control strategies, use of crankcase filtration, and use of three types of exhaust aftertreatment systems: (1) diesel oxidation catalytic converter (DOC), (2) combination of DOC and the full-flow wall flow monolith diesel particulate filter (DPF), or (3) combination of DOC, diesel exhaust fluid (DEF) based selective catalytic reduction (SCR) system, and ammonia slip catalyst (ASC). The study showed that the highest reductions in concentrations of diesel aerosols in underground workings, in terms of both mass and number, could be achieved if the engines, preferably in all power classes, are fitted with viable DPF systems. The use of U.S. EPA Tier 4 final engines equipped with DOC and DOC/SCR/ASC systems could help operators to considerably reduce mass, but not number concentrations of aerosols. The emissions of two of the evaluated engines, one equipped with DOC and the other equipped with DOC/DPF systems, were characterized by substantial secondary NO2 emissions that would limit the viability of those engines for underground mining applications. It appears that the catalyst formulations used in the exhaust aftertreatment systems of the “clean” engines marketed to the underground mining industry need to be formulated to minimize the potential for generation of secondary NO2 emissions. The results indicate that the engines fitted with viable SCR/ASC systems present a low-NO2 alternative. All three “clean” engines were found to have low CO output. Therefore, due to nuances associated with the use of diesel-powered mobile equipment in underground mines, special attention needs to be paid to the selection and potentially optimization of “clean” engines for underground mining applications.

Feb 1, 2025

By Z. Hyder, M. D. Cleason

"INTRODUCTION Mine Ventilation has come a long way over the years. The main purpose of mine ventilation is to keep conditions in the mine safe for the worker so that the mine will be productive and profitable. Technological developments to the mine ventilation system itself and the development of mining techniques have helped improve the safety and productivity of the miners and the mine. Most of the developments to mine ventilation and to safety devices came as the result of serious mining disasters. Another effect of those mining disasters, especially in the late 19th century and after, was legislation to set specific safety standards for mines, especially in the underground coal mines. This paper will focus on the connection between mines disasters and the mine safety legislations promulgated because of those disasters. A BRIEF HISTORY OF MINE SAFETY LEGISLATION Mine legislation has a long history in the U.S. dating back well in the 1800’s. However, mine safety legislation is considerably newer. In 1891, the U.S. Congress passed the very first version of mine safety legislations setting up minimum safety standards. By today’s standards, the 1891 legislation was incredibly basic (7). It took a series of horrific mining disasters for Congress to take action a second time. In 1910, Congress established the Bureau of mines. The role of Bureau developed and changed over next 60 years. In 1995, Congress voted to disband it (27). Initially the Bureau was only charged with investigating and coming up with ways to reduce accidents in coal mines. It was not until 1941, when Congress formally allowed Bureau of Mines’ Inspectors into the mines. In 1947, the Congress enacted and adopted a set of federal safety regulations for the inspectors to follow (1). Finally, in 1952 Congress granted the Bureau of Mines the authority to inspect the mines and to issue citations and/or orders of withdrawals. This act was known as the 1952 Coal Act and the penalties were limited to civil penalties. It would take a couple more iterations of mine safety legislation for monetary and criminal penalties to be introduced (10). Up until 1966, mine safety legislation was directed primarily at underground coal mines and surface coal mines. Congress passed the Federal Metal and Nonmetallic Mine Safety Act of 1966, thus providing a set of standards for all mines to follow (1). The 1952 Coal Act was amended again to be the Federal Coal Mine Health and Safety Act of 1969. This amendment was the beginning of modern mine safety legislation (13). In 1973, Congress created what can be considered the first ‘version’ of the modern day MSHA (Mine Safety and Health Administration). The initial version was the Mining Enforcement and Safety Administrations or MESA. Congress created MESA to act as the enforcement agency, relieving the Bureau of Mines of that responsibility so they could focus on their initial purpose, the development of countries natural resources (14). As mining industry grew, mine safety and health became a greater concern and priority. More efforts were put in legislating the industry. The Federal Mine Safety and Health Act of 1977 provided the platform for today’s mine safety and health legislation. Under the Federal Mine Safety and Health Act of 1977, also known as the Mine Act, MSHA came into being (1)."

Jan 1, 2016

By C. Williard

Computer based mine monitoring and control systems represent a relatively new technology to be applied in the U.S. mining industry. While computer assisted engineering, design, and planning have been accepted as tools for specific technical and engineering jobs within the industry, integrating mine-wide monitoring and control systems into mining operations has been slow. This paper reviews the state of the art of mine monitoring and control systems and provides insights into future trends and developments.

Jan 1, 1988

By J. LaForest, R. Riggle

In today’s challenging mining environment, everyone is focused on minimizing cost per ton. With haulage costs approaching up to 45% of the overall mining costs, and loader performance driving production, optimizing payload on the truck is a big opportunity. This paper will focus on technology’s role in loaders achieving the truck target payload. There are constantly new innovations in technology, but not everyone uses them correctly. Technology is intended to help achieve the next level of performance, but still requires the right people and processes to effectively utilize the benefits. In today’s mining business, miners, engineers, trainers, supervisors, and managers have ever increasing roles and responsibilities as never seen before in past decades. Technology can make these roles more efficient, but fully relying on the technology can detract from optimization. Sometimes the old-fashioned method of loading to a consistent pass match will provide a lower cost per ton. Before blindly trusting your technology feedback, know these three areas discussed in this paper: (1) Prerequisites to utilize technology in payload management; (2) Types of payload management technology; (3) How to use the data to manage operator behavior. The objective of this paper is to provide low-cost recommendations to efficiently increase production. INTRODUCTION Whether miners claim to have been around and experienced it all, or they are the data-driven new generation on the mine site, miners are expected to execute the mine plan at the lowest cost possible. So why is it so difficult to execute this task? Shouldn’t supervisors just have to staff the equipment, tell operators to have a safe day and tally up the numbers at the end of the shift? Let the technology system do the rest; what could go wrong? Lots. Having examined numerous mining operations that use the latest loading technologies over the past several years, one common denominator is the opportunity to improve loader operator performance. Mining companies seek help from consultants, training departments, performance reporting systems and an arsenal of resources. Armed with all this information, but the improvements don’t happen, what could have gone wrong? It comes down to people, not managing the resources to drive the right behavior and as a result, the mine’s performance is not where it should be. Understanding how to make “Great Miners” out of these people is critical to this constant struggle to move more with less and get the costs down. Extraction CPT (Cost-Per-Ton) is most sensitive to optimizing loader production which can be generalized into 3 categories of influence: machine specifications, cycle timing, and continuous management using technology. After establishing a basic production machine configuration, utilizing technology to manage cycle times, operator efficiency and payload can be advantageous. Prerequisites to Utilize Payload Management Technology It is important to begin with the primary considerations that enable the use of technology to continuously manage loading productivity. All systems are interdependent in mining, but these are divided into the simplest terms to remember. First, fix your timing and geometry.

Jan 1, 2019

By M. C. Stuttle

MDL Rock Lasers has undertaken successful mapping trials of abandoned mine workings using its underground cavity scanning system. The work was being performed for Kalgoorlie Consolidated Gold Mines (KCGM), Australia's largest gold producer. MDL Rock Lasers supplies underground surveying systems to the mining and quarrying industry KCGM's Fimiston Super Pit, located in Kalgoorlie, Western Australia, is Australia's largest open-pit gold operation. Fimiston's final pit design is expected to be 3.7 km (2.3 miles) long, 1.5 km (0.9-miles ) wide and 540 m (1,770 ft) deep. During the early days of Australian mining, underground operations were labor intensive. Mining was selective and generally narrow stopes were mostly backfilled. Improved processing technology and mine mechanization during the 1970s and 1980s has permitted larger scale operations to adopt less selective underground-stope operations. The "super pit" concept was a logical step for mining companies working toward economies of scale. However, the industry recognized that there was no precedent for excavating a 500-m- (1,640-ft-) deep open pit through ground previously affected by old workings. To appreciate the geotechnical challenge facing KCGM, it is necessary to consider that under the pro¬posed area at the open pit, stoping reached a level of 1 km (0.6 miles) and was supported by more than 2,000 km (1,240 miles) of development headings. The company was fortunate because plans were available for the Golden Mile underground operations. The existing plans were interpreted by the mine's geotechnical team and computer models were constructed of the underground workings. These models can be imported into three-dimensional mine planning packages, such as the Vulcan's Unix-based software, Envisage, to assist analysis and design. This prior knowledge of the workings provided the focus for investigating and confirming ground conditions using probe drilling. After several iterations of drilling, followed by detailed analysis, several decisions were made relating to the nature of the ground and the mining approach to be taken. It was recognized that the stope models were not perfect due to hu¬man error, lack of original survey information and progressive deterioration in ground conditions. It also became apparent that the sole reliance on probe drilling was inefficient in terms of time and quality of information. This was particularly true in complex areas where stopes are in close proximity. A major concern was the presence of open stopes (voids). In many cases, stopes consist of combinations of filled and void sections. The condition of pillars within these underground workings is extremely important. In time, pillars collapse and voids will propagate in upward and lateral directions. So systems needed to be developed that allowed rapid and accurate verification of ground conditions. KCGM was introduced to MDL Rock Lasers while investigating technology for underground mining. The two companies decided to use the C-ALS, MDL Rock Laser's underground laser, cavity scanning system, to improve the management of mining through affected ground. This system was to be used in conjunction with probe drilling and void mapping activities. A field test in one area of the Fimiston Mine verified the capability of the C-ALS system to quickly and efficiently assist in this decision making process. The C-ALS scanner features lightweight, carbon fi¬ber alignment rods from Measurement Devices Ltd.'s (MDL) Boretrak MKII. This is a borehole deviation system that stops the two axis measurement head rotating and lowers the system down a borehole. The scanner is deployed by a 110-mm (4.3-in.) borehole, up, down or sideways. The operator can then carry out vertical and horizontal plan section scans at any user specified ARC (an angular increment of 2°) or the distance between two points on the ARC (CHORD) increments. Windows '95 software enables the operator to control the cavity scanner remotely, surveying the area in real time. The system makes data quick and convenient.

Jan 1, 1999

By Siddhartha Roy, Hemant Agrawal, Ram Madhab Bhattacharjee, Devi Prasad Mishra

Heat stress is a major concern for the health, safety and productivity of miners working in hot and humid underground mines. At greater depth, heat inside underground mines increases due to geothermal gradient, heat released from high-capacity machinery, exposed rock surface, auto-compression of air, human metabolism, etc. Prolonged physical work in thermal environments severely affects the health, safety and efficiency of miners. In order to address this important issue, a systematic literature review (SLR) has been conducted. This SLR aimed to identify the research gap in the area of heat stress effect on underground miners and its control. An extensive literature search was carried out on numerous digital databases, grey literature and conference proceedings to identify relevant research work for this review. Moreover, the impactful studies, methodologies and preventive measures undertaken during the past five decades on the effect of heat stress on underground miners were retrospectively analysed, with a broader aim to explore the need for further research on this pertinent topic. Overall, 571 references were identified from the literature review, out of which 51 research articles addressing the sources of heat, heat stress effects on miners, heat stress indices and control measures for heat stress in underground mines were selected as primary papers for detailed review. Pre-developed fatigue is one of the prime causes of health hazard, safety and productivity loss of miners working in underground high heat stress zones. Hence, development of a better heat stress index integrating personal, environmental parameters and pre-developed fatigue (PDF) of miners is essential.

Jan 14, 2022

By Sam Rosenblum

The anomaly ratio is obtained by dividing the analyzed value of an element by the anomaly threshold value of the element. The sum of anomaly ratios for all anomalous elements in a sample may be compared with similar sums for other samples, so that the samples having the greatest anomaly-ratio totals can be recognized easily. In partial or full-suites-of-ore-elements the use of anomaly ratios is more meaningful than analyzed values because the ratios quickly indicate anomalous elements and call attention to samples and localities that should be investigated.

Jan 1, 1980