Search Documents

By Wm. Terry Siemer

Abstract. The value of industrial rocks and minerals produced in New Mexico in 1978 exceeded 227 million. 1e state ranked first in the nation in production of potash and perlite and was a leader in pumice production. Other commodities with sizable production in New Mexico include barite, caliche, clay, dimension stone, fluorspar, gypsum, humate, limestone, mica, salt, sand and gravel, scoria, and silica sand Non metallic resources are distributed throw out the state, but development and exploitation is concentrated in western and southeastern New Mexico. The value of industrial rocks and minerals within the state grew about 9 percent to more than $227 million in 1978. Continued growth, however, depends on continued demand, exploration, and development.

Jan 1, 1980

By DEVY DYSON, Brian Hart, JOHN LANGHANS, Stamen Dimov, STEVE YOPPS

A recent Nevada Gold Mines research program focused on pressure oxidation pre-treatment of a Carlin-type double refractory ore from the Turquoise Ridge Mine. The research team found that both arsenian pyrite and carbonaceous matter were highly oxidized within an hour at 300 °C using a bench-top autoclave reactor and that the gold recovery from the residues after cyanide/carbon-in-leach approached the technical limit set by the amount of gold encapsulated by silicate minerals. Although the 60-min pre-treatment at 300 °C yields robust performance when treating a whole ore, copper additives can catalyze the oxidation rate of carbonaceous matter and reduce the residence time needed at elevated temperature. Certain gangue minerals are susceptible to dissolution in acidic solutions at 300 °C, and this may cause poor gold recovery. This recovery challenge is mitigated by keeping free acid in the discharge solution below a key threshold.

Jun 21, 2022

By Keith G. Wallace, Oscar Codoceo

This paper describes the ventilation planning that was per- formed at the Barrick Gold Corporation, El lndio Mine. The El lndio Mine is located at an elevation of approximately 4,000 m in the Andes mountains east of the coastal city of La Serena, Chile. The ventilation planning program consisted of a detailed ventilation survey of the mine and the establishment of a correlated com- puter model. A series of network simulations were conducted to determine the optimum position, size, and configuration of new ventilation raises and main fan exhaust system. Modifications to existing mine infrastructure including; driving of drifts, slashing of airways, and positioning of ventilation controls were examined. Detailed costing information was developed to optimize the location of the new main exhaust raises and fan system. The final ventilation system is expected to increase the mine airflow from the existing 157 m=/s to over 315 mls. This increase was necessary to accommodate an expansion in mine production, diesel equipment utilization, and deeper mine development. Furthermore, the increased airflow was required because of the de-rating of diesel equipment and large air volumes necessary to dilute diesel exhaust at high elevation.

Jan 1, 1997

By W. R. Reed, G. W. Luxbacher

Mine worker exposure to respirable coal dust and silica dust can result in coal workers’ pneumoconiosis and silicosis which are occupational respiratory diseases that have no cure and are ultimately fatal. In 2021 the Mine Safety and Health Administration reported just over 11,000 operating metal/nonmetal mines with the potential for silica dust exposure for just under 200,000 miners. The National Institute for Occupational Safety and Health (NIOSH) conducts respirable coal and silica dust research associated with mining through its Office of Mine Safety and Health Research. NIOSH respirable coal and silica dust research began under the U.S. Bureau of Mines (USBM), which initially examined silica dust, progressing to include coal dust, with a stronger focus after 1969 with the passage of the Federal Coal Mine Health and Safety Act. A review of extramural research to develop real-time respirable silica dust monitor is presented along with a brief history of silica dust regulation.

Feb 1, 2024

By John Hanna

Recently. researchers at The University of Alabama have developed a two-step method for the treatment of phosphorus sludge that includes bulk removal of phosphorus by physical separation techniques followed by remediation of the residual P4 in the sludge using a novel wet air oxidation technique known as "HSAD", Tests made on samples of the electric furnace phosphorus sludge have demonstrated that essentially complete and fast removal of the P4 in the sludge can be achieved by the HSAD wet oxidation treatment, Further studies were made to determine the applicability of the two-step process on sludges of various origins. P4 contents different pre-treatment and storage conditions, The present work discusses the mechanisms and factors controlling the HSAD wet air oxidation remediation approach.

Jan 1, 1992

By Nikhil Dhawan, Veeranjaneyulu Rayapudi

This study investigates upgrading of low-grade banded hematite quartzite iron ore (Fe ~31%). Conventional beneficiation was found to be futile. The susceptibility of iron phases to microwave exposure and their selective absorption assists in the liberation of iron values. Microwave exposure of coarse particles at 540 W for 10 min yielded a concentrate with Fe 56.30% and recovery of 50.68%. Conventional carbothermic reduction at 500 °C, 60 min and 9% charcoal yielded a concentrate with Fe 57.6% and iron recovery of 68%. The presence of sufficiently bonded silica leads to an easy formation of a fayalite phase. The microwave reduction design yielded FeG of 57.6%, FeR of 47% and a yield of 24% at an optimal condition of 540 W, 8 min and 6% charcoal. It was found that a small fraction of microwave-irradiated ore-charcoal mixture melted rapidly, and pure ferrite balls were observed within 8 min. An optical micrograph of a ferrite ball reveals the retained austenite and martensite phase.

By Tyler Lahti, Peter Borgacci, Mary Jane Ferraro, Prakash Nadesparan

Toronto Tunnel Partners (TTP), under contract to Metrolinx/IO, is constructing new twin rail tunnels under the Highway 401 & 409 interchange to accommodate additional tracks to support the GO Expansion program for future two-way, all-day service. The new tunnels are being constructed using the Sequential Excavation Method (SEM) and utilize a tunnel pre-support system consisting of a series of 800 mm diameter steel pipes to form a pipe canopy. The pre-support pipes were installed with an Auger Boring Machine (ABM) in four separate headings; one heading from each of the tunnel end portals, and two from a shaft in the middle of the highway. To facilitate the auger boring operation, a custom steel reaction frame was required to counteract the thrust from the ABM at the portals, and a temporary shaft structure was installed in a narrow median space of the highway. The installation of the pipe canopy had to overcome challenges including removal of obstructions, alignment issues, and controlling settlements to the highway surface. This paper discusses the purpose of the pipe canopy, design and installation of the temporary shaft and structures to support the auger boring operation, the experience of the contractor during the installation of the pipes, and brief overview of the experience tunneling below the pipes.

Jun 13, 2021

By P. Knudsen, S. Rosenthal

INTRODUCTION In 2010, Montana Tech was gifted 65 acres of land immediately west of the campus. The parcel of land included an old silver mine called the Orphan Boy Mine. The Orphan Boy and its sister, Orphan Girl, were developed about1895 and operated until 1956. In addition to the gift of land, a significant industry gift was obtained to develop a first class training facility, which we call the Underground Mine Education Center (UMEC). The UMEC has been funded primarily by industry through donations of dollars, equipment, and supplies. The UMEC is a unique hands-on, educational environment for today’s students who are being trained to find, develop and process the worlds' natural resources. The center complements courses in mining engineering, geological engineering, environmental engineering, metallurgical engineering and occupational safety and health. It also serves as a as research facility utilized by students and faculty, and other organizations interested in doing research a hard rock underground mine. LOCATION The Orphan Boy and Orphan Girl Mine are located approximately 700 feet (ft.) apart and the Orphan Girl Mine is part of the World Museum of Mining. Underground they are connected on various levels and all levels below the 100 ft. level are currently flooded. The Orphan Boy mine was 804 ft. deep and Orphan Girl was 3200 ft. deep. The surface locations of the two mines and some of the underground workings on the 100 ft. level are shown on Figure 1 (2015). CONSTRUCTION Land ownership was gifted from BP/ARCO in 2010 and planning started immediately. In June of 2011, site development for the decline to the 100 ft. Level of the Orphan Boy began with a satisfactory portal site developed (Figure 2). We hoped to be able to start driving the decline in July. However, the portal was sited approximately 125 ft. away from a natural gas line that bisected the Montana Tech campus. While outside the right of way for the line, Northwestern Energy requested that no blasting be performed near the gas line until such time as the gas line was abandoned in the fall so decline development was put on hold. The gas line was officially abandoned in January of 2012.

Jan 1, 2019

By Shahab Alizadeh, Ahmad Khodadadi Darban, Mehdi Mohseni, Mahmoud Abdollahy

This study probed the selective separation of lanthanum and yttrium in a nitrate medium in the presence of aluminum and calcium impurities using di-(2-ethylhexyl) phosphoric acid (D2EHPA). The factors studied in a central composite design (CCD) included extractant concentration, pH, concentration ratio of total impurities to rare earth elements, and interaction of these three factors. The extraction mechanism and types of extracted metal-containing species were delineated by the slope analysis method. The obtained thermodynamic data showed that lanthanum and yttrium extraction by the D2EHPA extractant was exothermic. The extraction of both rare earth elements was accompanied by an entropy reduction. The negative magnitude of ΔS in yttrium extraction reaction suggests stronger D2EHPA-Y(III) complexation relative to La(III). As entropy decreased and enthalpy increased, the extraction process became unspontaneous. Using the proposed flowsheet, lanthanum and yttrium products with > 90% purity were obtained.

Aug 10, 2021

By H. Sevim

Mining engineering curriculum has been discussed and debated in meetings and conferences, and opinions and recommendations have been published in the literature since the inception of the official degree-granting mining engineering program at the Columbia School of Mines in 1864. The deliberations have usually been heightened during the periods of boom-and-bust cycles experienced by the mining industry since the 1920s. Currently, the global natural resource industry is undergoing another cycle, called ?super cycle,? characterized by elevated prices for metals and other natural resources. The super cycle is occurring as a result of the large deficit between the global supply and demand for natural resources, due, in large part, to economic expansion and development in countries such as China, India and Brazil. Because of this cycle, there is a shortage of mining engineers in the U.S., Canada and Australia.

Jan 1, 2012

By F. Calizaya

A booster fan is an underground fan installed in series with a main surface fan and used to boost the air pressure of the ventilation air passing through it. To accomplish this objective, the fan is installed in a permanent stopping and equipped with airlock doors, a monitoring system, and interlocking devices between main and booster fan controls. The stopping and doors are used to prevent flow recirculation, and the monitors to ensure safe operation of the fan. A booster fan, properly sized and sited, can be used to create safe work conditions and allow the extraction of minerals from areas that would otherwise be uneconomic to mine. In deep and large mines with heavy emissions of air contaminants, the required quantities of air can only be supplied by using high pressure fans. These fans will inevitably induce significant losses of fresh airflow through the stoppings and doors. For well defined ventilation circuits, booster fans can be used to decrease the main fan pressures and reduce the leakage flows. However, this will require a good understanding of the correct ventilation practice, from planning to operation and maintenance of booster fans. The objective of this study is to investigate the conditions under which booster fans can be used safely and efficiently in underground coal mines. Specifically, the study is directed at (1) collecting reliable information on airway resistances and flow requirements from two large U.S coal mines, (2) collecting fan performance data from one or more existing coal mine where booster fans are used regularly, (3) monitoring the performance of booster fans in a laboratory model and an experimental mine, (4) developing a booster fan selection method to assist the ventilation engineer at the planning stage, and (5) training six M.S. or Ph.D. graduate students in advanced mine ventilation.

Jan 1, 2010

By Jr. Watts

The American Mining Congress and the U.S. Bureau of Mines have formed a collaborative research team to develop, implement, and evaluate a comprehensive control strategy to reduce diesel particulate matter concentrations without degrading other air quality parameters at an underground noncoal mine. Other participating organizations include Caterpillar, Inc., the Mine Safety and Health Administration, and the University of Minnesota. After extensive baseline information and air quality data are collected, available control strategies to reduce diesel particulate matter exposures will be implemented, individually or in combination, and evaluated. This paper discusses the objectives and protocol of the collaborative effort to evaluate diesel particulate control technology.

Jan 1, 1995

By D. K. DeForest

The olfactory system (sense of smell) is crucial to the ability of fish to avoid predators, recognize kin, and synchronize reproduction (Baldwin et al. 2003). Copper (Cu) has been shown to impair olfaction in juvenile freshwater life stages of salmonids (including Pacific salmon and trout) in some laboratory experiments; and in the United States, public concerns have been expressed that current regulatory criteria for Cu in fresh water are not adequately protective of olfactory function in salmonids (e.g., OSU 2007; Pearson 2007). These concerns have largely been raised because some Cu concentrations that have caused olfactory impairment in salmonids in the laboratory are less than Cu concentrations that have been shown to reduce salmonid survival, growth, or reproduction (the effects endpoints that are typically considered in deriving ambient water quality criteria). However, two important and interrelated points that must be considered: (1) freshwater Cu criteria are "driven" by the sensitivities of several invertebrate species that are more sensitive than the olfactory impairment threshold in salmonids when (2) the influence of water chemistry on Cu bioavailability is properly considered in deriving Cu criteria. Bioavailability refers to the ability of various chemical forms of Cu to interact with receptors on the surface(s) of organisms and thus directly cause toxicity or uptake by the organisms. The toxicity of Cu and other metals to aquatic organisms is a function of water chemistry. For example, acute Cu toxicity in fresh water generally decreases as pH, water hardness (Ca2+ and Mg2+), alkalinity, and dissolved organic carbon (DOC) concentrations increase (Meyer et al. 2007). The U.S. Environmental Protection Agency (USEPA) has recommended hardness-based freshwater aquatic life criteria for Cu and other metals since the 1980s (e.g., USEPA 1985); and hardness-based metals criteria decrease (i.e., become more restrictive) as water hardness decreases. More recently, the USEPA has recommended freshwater aquatic life criteria for Cu based on the biotic ligand model (BLM; USEPA 2007), which accounts for the influence of multiple water chemistry parameters, including DOC, pH, alkalinity, Ca2+, Mg2+, and several other cations and anions. The BLM-based Cu criteria generally decrease as DOC concentration, pH, alkalinity, and water hardness decrease. Because DOC has a stronger influence on Cu bioavailability than water hardness, hardness-based and BLM-based Cu criteria can differ considerably. For example, in water that has low DOC and high hardness, the hardness-based Cu criterion would be relatively high (because it is driven by the high hardness) but the BLM-based Cu criterion would be relatively low (because it is driven by the low DOC). Thus, any evaluation of the protectiveness of Cu criteria against a given effect, such as olfactory impairment, must properly account for the chemistry of the exposure water. Meyer et al. (2013) compiled data on Cu-induced olfactory impairment and olfactory-induced behavioral effects from tests in which BLM parameters were measured. They demonstrated that the USEPA's BLM-based freshwater life criteria for Cu are protective against olfactory impairment, because it adequately accounts for water chemistry (whereas the USEPA's hardness-based Cu criteria are not consistently protective). Olfactory impairment by Cu is now receiving increased attention in Canada and Europe (e.g., Wall 2013; Stang 2013). Accordingly, in this paper we have expanded the analysis of Meyer et al. (2013) to consider copper guidelines from various other countries and whether these guidelines are protective against olfactory impairment.

Feb 23, 2014

By Rebecca Boakye, Zohreh Kazemi Motlagh, Virginia T. McLemore

The most significant uranium (U) deposits in New Mexico are sandstone-hosted deposits in the Morrison Formation (Westwater Canyon Member), where >169,500 short tons of U3O8 were produced from 1950 to 2002. In addition, >9076 pounds of vanadium (V, a critical mineral) and some molybdenum (Mo) were produced from these deposits. These and other U deposits (limestone-hosted, U-veins) in New Mexico also contain critical minerals. Critical minerals are mineral resources that are essential to our economy and whose supply may be disrupted; many critical minerals are 100% imported into the U.S. Some sandstonehosted, limestone-hosted, and U-vein deposits are elevated in heavy rare earth elements. One sandstone-hosted sample contained 0.3 ppm Re (critical mineral), 659 ppm Se and 408 ppm Mo. The arsenide five-element vein deposits in the Black Hawk district are mineralogically and texturally complex, low- to moderate-temperature, hydrothermal, structurally-controlled, Ag-Co-Ni-Bi-As bearing carbonate vein systems with local minor elements. Mineralized samples from Black Hawk contain up to 9970 ppm Ag, 8540 ppm As, 5690 ppm Co, 72,400 ppm Ni, 57 ppm Bi, 165 ppm Sb, and 32,600 ppm U.

Feb 22, 2026

By Valeh Aghazadeh, Shima Barakan, Mina Soleymani, Ehsan Bidari, Morovvat Faridazad

Molybdenite is the most important molybdenum concentrate, which is mainly recovered as a by-product from porphyry copper deposits. Due to the low efficiency of purification processes such as flotation in the reduction of copper content of molybdenum concentrate to a standard level (i.e., less than 0.5 wt.%), further purification by a hydrometallurgical method is required. Although different types of chemical reagents were found to be effective in the leaching of copper minerals from molybdenum concentrate, the mechanisms of these processes remain largely unexplored. In this study, optimal conditions for maximum copper leaching (> 99%) were obtained at the concentration of HCl = 1 M, FeCl3 = 0.5 M, CuCl2 = 0.05 M, CaCl2 = 0.5 M at 75 °C, 500 rpm, and S:L = 1:10 during 60 min. CuCl2 was identified as the most effective leaching reagent for copper dissolution in agreement with Visual MINTEQ model results due to the formation of various types of copper chloride complexes. Furthermore, the electrochemical behaviors of FeCl3, CuCl2, and CaCl2 reagents before and after the leaching process were investigated by the cyclic voltammetry technique. The results of cyclic voltammograms at different scan rates verified the presence of copper chloride complexes, and ferric ions as the oxidizing reagents for better dissolution of copper sulfides. Based on kinetic study results of shrinking core models, both chemical and diffusion reactions controlled the copper leaching process with an obtained activation energy of 33.56 kJ/mol. For recovery of the leached copper, the precipitation process was done by the addition of Na2S at 45 °C, S/Cu = 1, and pH = 9.

Dec 26, 2022

By Yoichi Shimada, Katsuyuki Nishida, Shinichi Takahashi, Yasushi Okada, Yohei Nakamichi, Kazunori Oshiro, Taichi Terui, Sigehiko Sugie

"Temporary retaining walls are ordinarily used for tunnel construction work conducted using the opencut construction method. Retaining walls in such instances are typically installed vertically. However, shoring (such as struts and king posts) is required to ensure the stability of retaining walls in cases of excavation work to depths that exceed approximately 4 m. A new design and construction method that focuses on the effectiveness of retaining walls that are installed on an incline was studied with the aim of improving construction workability by omitting shoring. The inclined braceless excavation support (IBES) method, which was developed for use with the inclined buttress method, requires no shoring, even for deep-open-cut construction work and can be applied to deep excavation work on ground with a high groundwater level. This method has been applied at six work sites in Japan in recent years. This paper introduces the IBES design and construction method and presents verification results based on the design method, a model experiment, finite element analysis, and measurements obtained during construction work.INTRODUCTIONBackgroundIn the past, temporary retaining walls used in open-cut construction work have been installed vertically, and shoring (such as struts and king posts) has typically been used to ensure the stability of these retaining walls when the excavation depth reached 3–4 m. However, shoring interferes with structures built within excavations and requires box-outs and penetration sections in the structures, as well as concrete joints that raise concerns about their impact on the watertightness and long-term durability of structures (Figure 1).Shoring also narrows the space available for conducting construction work and reduces construction work efficiency, and the installation and removal of shoring increases the construction duration and cost. As a result, there has been a demand for ways to reduce or eliminate shoring to improve the quality of structures and construction work efficiency."

Jan 1, 2016

By V. Z. Sun

One of the major concerns of ground control in a coal mine is safety against failure of one of three components (i.e. roof, pillar, or floor) of the mine entry. In order to better design and evaluate stability of the mine entry with a certain confidence, a reliability approach is introduced rather than using the conventional safety factor (SF) method only. Advantages of using the reliability approach is that it not only takes variability of both rock/coal properties and stress distribution into consideration, but also assesses the stability of each component and mine entry as a whole system. Therefore, it is anticipated that, by using this approach, the current ground control technology in coal mine will convey a better sense of confidence. The results of a case example show a significant influence on the current design concept and stability evaluation of mine entry.

Jan 1, 1997

By G. B. McClurg

China was nota factor in the supply of fluorspar to the United States until the early 1980's when it shipped in its first package of Metallurgical lump, that not only was higher grade than the Mexican Metallurgical spar but was also about $30.00 a ton cheaper landed at Burnside. Representatives of the Mexican Fluorspar Institute and several producers made trips to see the Chinese operations supplying their once reserved market place. China, an enigma to most Westerners suddenly became the new contender, with prices that were disgustingly low or so thought the other exporters. Of course China has been mining, producing, consuming and exporting from 400,000 to 500,000 tons per year of various grades of fluorspar but until the first partloads came to the U.S., very little attention was paid to their exports by American-continent producers or consumers.

Jan 1, 1986

By Ryan C. Stephan, Zach Agioutantis, Christopher Mark

During the past 15 years, roof fall rates have fallen dramatically in US coal mines, particularly in regions where the roof is weakest. The remarkable reduction in the number of roof falls has been accomplished with more effective roof support systems. The purpose of this paper is to present a design methodology that builds on and quantifies the basic roof support concepts that have been successful in the USA. The methodology starts by defining three modes of roof support, based on the roof strength relative to the stress level: (1) suspension, where roof bolts mainly provide skin control for strong roof; (2) beam building, where moderate strength roof can be supported by roof bolts alone; and (3) supplemental support for weak roof. Next, a large database of roof fall histories at a number of mines is used to define the approximate boundaries of these three regimes based on the coal mine roof rating and the depth of cover. Finally, guidelines are presented for site-specific design of support systems within each regime. The new computer package, analysis of mine roof support (AMRS), implements the design methodology.

Sep 29, 2020

By Duane L. Abata

Toxic gases produced by the detonation of six explosives were measured in an underground hardrock metal mine during actual mining operations. The six explosives included two semigelatin dynamites, three slurry explosives and an ammonium nitrate, fuel-oil/ammonia dynamite combination. Explosives were detonated at the face of a drift and the toxic gases produced by the detonation were trapped to the end of the drift by a bulkhead located a short distance away from the face. Toxic gas concentrations were then measured with direct readout instruments and together with the containment volume, the toxic gas volumes per mass of explosive were calculated. Toxic gas measurements were found in the following ranges (ft3/lbm): NO, 0.010-0.035; NO2, 0.003-0.019; CO, 0.08-0.30; S02, 0.00-0.05; and CO2, 0.7-1.8. Results showed that toxic gas production (ft3/lbm) correlated with the densities (kg/m3) and energy densities (kJ/kg) of the explosives tested.

Jan 1, 1979