Search Documents

By G. T. Lineberry

There is a critical need for effective instructional materials at the university level and for an upgrading of mine safety and health in the mining engineering curriculum. A fundamental approach to mine safety and health is recast into the familiar 3 E's: engineering, education, and enforcement, in that order. Each is briefly reviewed and their interdependence emphasized. A unique philosophy for successfully integrating safety and health principles into the mining engineering curriculum is offered. The concept of textbook ?tailoring? is discussed and defended, permitting rapid assemblage and synthesis of existing educational materials. Final recommendations are made for a u, comprehensive approach to mine safety and health education in the undergraduate curriculum.

Jan 1, 1987

By Jian Liu

The dissolubility of a natural sphalerite (ZnS) in the entire pH range was theoretically calculated, and its practical dissolution in an aqueous solution at different pH values in an inert environment, together with its surface properties after dissolution, was fully investigated. The results of the investigation indicate that the total concentration of Zn (CZnT) decreases significantly with the increase of pH value, while the pH value is set below 8; however, it reverses when the pH value reaches 8. Such a tendency is similar to that of the theoretical calculations, although the experimental CZnT were much higher than those of the theoretical calculations. The X-ray photoelectron spectroscopy (XPS) of the sphalerite surface after its dissolution under alkaline solution shows that a polysulfide (Sn 2-) surface layer with a binding energy (BE) value of 162.96-163.25 eV is present on the surface, and the percentage of Sn 2- increases significantly with an increase in pH value; the undissolved and dissolved sphalerites under the acidic solution have a negligible difference in S2p peaks. The surface S/Zn ratio of all dissolved sphalerites shows a marked Zn enrichment and S deficiency. An atomic force microscope (AFM) view of the sphalerite surface, after its dissolution under the alkaline solution at a pH of 12, shows that the surface is significantly different in morphology from that of the undissolved one.

May 1, 2012

By William A. Rehrig

During recent years, there have been frequent investigations on the geochemistry of biotite. This work has emphasized, and no doubt was prompted by, factors related to mineral exploration, particularly for those deposits of the porphyry copper type. A large number of papers have been devoted to the obtainment of trace-element data from plutonic biotite. These data have been used to extract primary geochemical information pertaining to the parent magna and the hydro-thermal system which together give rise to porphyry copper deposits. In two early works, Putman and Burnham (1963) and Parry and Nackowski (1963) analyzed base metal contents of ferromagnesium minerals, primarily biotite, from various barrenfmineralized plutons of the Basin and Range Province. One similar conclusion from the two studies was that the Cu, Zn, and Pb contents of magmatic biotite served as indicators of ore development within the granitic rocks genetically related to ore. This theme was then pursued vigorously by a number of authors until the present time. Results, however, have been contradictory, as reviewed by Coope (1974). For example, studies by A1 Hashimi and Brownlow (1970), Lovering et a1 (1970), Putman (1972), and Graybeal (1973) continued to support positive primary relationships between the trace-metal content (usually copper) of biotite and associated sulfide mineralization. By studying biotite in close spatial association will sulfide occurrences, Putman (1972) and Graybeal (1973) developed models for base metal partitioning in magmatic systems based on their discovery of inversely distributed copper between silicate (biotite) and sulfide phases. Conversely, research by Bradshaw (1967) and Blaxland (1971) plus the recent findings of Parry and Jacobs (1975) and Kesler et a1 (1975) found little if any evidence to support a correlation of biotite base-metal or

Jan 1, 1976

By G. van Eck, H. Smit, L. Meyer

The Cook Islands (CI) possesses within its Exclusive Economic Zone (EEZ) a massive field of polymetallic nodules representing one of the world’s largest undeveloped cobalt deposits, along with large quantities of other metals critical to achieving global energy transition targets. In February of 2022 the Seabed Minerals Authority (SBMA) of the CI granted Moana Minerals a license to conduct our nodule exploration program. This paper describes how Moana Minerals chose to approach conducting exploration activities, one of the greatest challenges to Deep Sea Mining (DSM) development and the securing of the social license to advance to eventual mining of the resources, in an unconventional manner. The remote location of the project poses logistical challenges in mobilizing to and operating in the region and is a significant cost driver. Historically, exploration campaigns mobilized large vessels from mainland Europe, the Americas, and Asia as this model works well when contemplating long duration and widely temporally spaced campaigns without the need to revisit. Moana Minerals, when considering these challenges determined a multi-year deep sea mining (DSM) exploration program conducted in such a remote location can be better optimized by the deployment of a smaller yet highly capable “exploration optimized” vessel that is dedicated to the task and is based full time in the Cook Islands. INTRODUCTION The paper describes the challenges of exploration in remote regions including the South Pacific, and how an unconventional consideration of the problem led to the solution. Completion of an Environmental and Social Impact Assessment begins with a detailed environmental scoping study, resource update sampling requirements, and engineering data and sample requirements, which identifies the exploration goals of the project and technology needed to accomplish those goals. The method walks the reader through vessel and technology selection, discusses the challenges of equipment selection considering size and capability, describes the final arrangement, and provides results from the initial exploration campaigns. We followed the project from conception through the shipyard conversion, mobilization, and initial operations in the Cook Islands. The result shows how a smaller vessel with limited budget makes a large impact on the exploration capabilities in the region while building public trust. The Anuanua Moana is the first dedicated deep sea minerals exploration vessel modified with a suite of technologies that allow it to compete technically with existing ships but operate locally in the smaller ports of the South Pacific. The unique combination of size and technical capability gives the Anuanua Moana advantages over other vessels. This paper shows the importance of the Anuanua Moana in the development of offshore exploration strategies in the emerging deep sea minerals space.

Feb 22, 2026

By Donald H. Dowlin

The design of a preparation plant for minimum maintenance and clean up requires both the skills of the Engineer and the practical experience of the Operator. From the initial flow sheet and preliminary design until the plant is completed and operating, each phase of the work must be thoroughly explored for simplicity, workability and high efficiency. It is the responsibility of the Designing Engineer to develop the plant around the basic flow sheet, selecting equipment and materials not only with regards to Initial cost but also required upkeep and repair.

Jan 1, 1962

By Björn Johansson

"SUMMARY Every tunnel designer has to consider the power of water ingress when designing a new tunnel. Either you choose solutions with simple methods to divert the ingress water or a robust system with the intention that it will give gain on low maintenance costs and a long lifetime. This article describes a new method to divert ingress water in a robust way and more economical than traditional concrete lined tunnels. This system is based on a bolt grid suspending a water tight membrane, which is reinforced and covered with sprayed concrete. The method has been in limited use in Sweden since 2005 and with continuous improvement, still going on, it is now applied for the large project “Stockholm Bypass”, a 21km long highway project. TUNNEL MAINTENANCE RELATED TO WATER INGRESS The Swedish Transport Administration maintain approximately 190 various tunnels that is constructed by a number of different methods, (Swedish Transport Adm 2015). Commonly the ground conditions are good and fairly low ground support is needed. Contrary water and winter conditions can be sever, which gives high impact onto the tunnel design and in particular methods to protect against “frost and water ingress”. During a tunnels lifetime it is common that maintenance related to water ingress occurs several times and sometimes frequent occasions every year. Such maintenance costs and consequences of lost open time for the tunnel can rapidly become higher than the initial cost of the tunnel. Thereby it is obvious that spending time during design to evaluate requirements for a suitable system against water ingress is preferred. Icicles Icicles are formed when water is below freezing degrees and drips or run from an ingress point. At very cold conditions also water flows running at high velocity freeze into ice and a rapid growth can appear. If the integrity of the tunnel traffic area is interfered by icicles they urgently have to be removed before they cause an accident. Typically the tunnel or a part of the tunnel must be closed to do such maintenance. TUNNELS FROST AND WATER INGRESS PROTECTION IN SWEDEN In Sweden methods to perform “frost and water ingress protection” are primary developed for drill and blast tunnels as it is most common tunneling method. The foundation Swedish Rock Engineering Research has done a comprehensive report SveBeFo Rapport 77 that describes water and frost prevention in Swedish tunnels up to year 2005. Below is only slight description of those various methods. Lately some more attention is paid to concrete lined tunnels made by TBM since TBMs successfully built water tight tunnels in City Tunnel (Malmö) and Hallandsås Project. When environmental demands require maintained ground water levels, water tight tunnels made by pressurized concrete lining becomes more economical and on the same time also becomes protected from icicles and water drips."

Jan 1, 2016

By Stephen M. Voynick

Two hours driving time west of Denver, CO and 21 km (13 miles) north of Leadville, Bartlett Mountain rises 4,065 m (13,337 ft) high in central Colorado's Tenmile Range. Bartlett Mountain is one of Colorado's most recognizable peaks, especially when the late afternoon sun casts a surreal, reddish light across its most prominent feature - the Glory Hole. This is a gaping, half-mile-wide, 245-m- (800-ft-) deep crater. Created by subsidence from 60 years of massive underground mining, the Glory Hole is a monument to the Climax Mine, one of the great achievements in American mining and metallurgy. For most of this century, the name Climax has been synonymous with brilliant mining engineering, innovative metallurgical research and entrepreneurial promotion of a once-obscure metal - molybdenum. Climax overcame an array of economic, technological and social problems to become a model for underground development of massive deposits of low-grade ores. It is one of the few mines in the world where cumulative production is measured in the billions of dollars. The Climax mineralization was emplaced 30 million years ago. Magmatic intrusions formed a large, mineralized stockwork within the granite country rock of Bartlett Mountain. Associated hydrothermal events forced superheated metal- and quartz-rich solutions through fracture zones, silicifying the country rock and depositing huge amounts of molybdenite, or molybdenum disulfide. The mineralized rock, a light gray, finely crystalline, silicified granite, is laced throughout with blue-gray quartz veinlets containing molybdenite. Although the richest ores graded only about 1% molybdenite, the Bartlett Mountain deposit contained more than 2.7 Mt (3 million st) of elemental mo- lybdenum.

Jan 1, 1997

By David Hanson, Sean Warren, Chaparral Berry

"Coal bumps, also referred to as dynamic failure events or coal bursts (Lawson, Weakley, and Miller, 2016), continue to be a hazard in underground coal mines. While current design methods have significantly reduced the occurrence of coal bumps, they have not been completely eliminated. This paper investigates a correlation between coal compositional components, coal molecular structure, and probability of coal bumps in an effort to deepen understanding of coal behavior in an effort to reduce hazards in underground coal mines.Samples from the Penn State Office of Coal (PSOC) Department of Energy Coal Samples (DECS) were obtained for Fourier Transform Infrared Spectroscopy (FTIR) analysis using the KBr pellet method. Peaks indicative of the coal molecular structures were obtained using spectral integration software. These data, combined with published elemental data, were compared to historic bump occurrence in order to establish a possible correlation. Finally, results based on multivariate analysis of the elemental and FTIR data with bump status as the dependent variable suggest that elemental sulfur and molecular structure can be used as an indicator of bump susceptibility within the sample set considered.INTRODUCTIONThe study of coal requires consideration of multiple variables: percentages of organic and inorganic components, organic component origins, coal age, pore structure, cleat density, elemental composition, etc. Examining coal in situ increases the number of variables, such as coal depth, seam thickness, surrounding stratigraphy, and so forth. This collection of variables influences the subsequent behavior of coal simultaneously, and weighing their relative impact is a challenge for researchers. “A problem never exists in isolation; it is surrounded by other problems in space and time” (Ackoff, 1956). Having a substance such as coal that we know so much about, and yet so little, we have to ask what can be learned.An experimental study using Fourier Transform Infrared Spectroscopy (FTIR) was undertaken to determine if the chemical structure of coal contains information which may lead to a better understanding of triggers or attributes which may, in turn, lead to an increased probability of a dynamic failure event. While a full analysis of the factors driving dynamic failure are beyond the scope of this study, it is possible that a better understanding of the chemical structure of coal will lead to an increased knowledge of its inherent behavior, including its propensity to burst."

Jan 1, 2019

By Ben Roderds

The Waneta Expansion Project (WAX) is located near the existing Waneta Dam site at the confluence of the Pend d?Oreille and Columbia rivers, approximately 10 km (6.2 miles) south of Trail, BC, Canada. The WAX owners consist of a partnership between Fortis Inc., Columbia Basin Trust and the Columbia Power Corp. This design-build project was awarded to SNC-Lavalin in late 2010 and is expected to be operational in mid-2015. The WAX consists of a new 335-MW powerhouse, including two new Francis turbine units, each generating approximately 167 MW. The powerhouse is located downstream of the existing Waneta Dam, and will make use of excess water that would otherwise be spilled during the runoff season. Water will be funneled to the turbines through an intake structure and two 10.5- m (34.5-ft) diameter, concrete-lined Penstock Tunnels. A 10-km (6.2-mile) transmission line will connect the powerhouse to existing electrical grids. Redpath/FKCI Waneta Tunnelers (RFK) was subcontracted by the heavy civil contractor, the Aecon/SNC Lavalin (ASL) joint venture, to excavate the two penstock tunnels and install the cast-in-place concrete liner. RFK is a joint venture partnership between J.S. Redpath Ltd., an underground mine contractor located in North Bay, Ontario, and Frontier-Kemper Constructors ULC, a heavy civil tunneling contractor based in Nova Scotia, Canada. Since penstock tunnel excavation was planned using drill-and-blast methods with a significant grade of more than 17 percent, the combined experience of these two contractors was a perfect match.

Mar 1, 2014

By S. M. Moore

Each year more than 400 coal miners are injured (fatally and nonfatally) by rock falling from between or around roof supports. Many of these injuries can be prevented by the installation of roof screen. However, many coal mines are reluctant to use roof screen because of the added cost. The goal of this study was to determine the potential savings in workers' compensation (W C) premiums that can be achieved due to a reduction in rock fall injuries after roof screening. The WC rate-setting methods utilized by Illinois and Kentucky were investigated in this study. Using data obtained from the Mine Safety and Health Administration, national and state WC bodies and individual insurance companies (e.g., average cost per injury, loss cost rate, number of injuries per year, number of injuries preventable each year with roof screening), baseline mines (representing two mine sizes: 67 and 150 employees) were constructed with realistic ranges for estimates of injuries and WC premium costs. Using each state's actual WC rate-setting formulas, a sensitivity analysis was conducted to determine the total savings in WC costs after a three-year period. Annual savings in WC premiums ranged from $41,000 to $326,000 for the 67-person mine, and $96,000 to $843,000 for the 150-person mine. An economic analysis of the cost of a roof screening program at a 67-person mine was also conducted. The annual cost of a roof screening program here was estimated at $240,000. At this mine, the reduction in WC premiums alone could pay for the entire screening program.

Jan 1, 2010

By ANGELA NAIR AVELAR, Reiner Neumann, PAULO R. G. BRANDÃO

Three types of apatite were identified by means of cathodoluminescence (CL) images in flotation concentrate and tailing samples from the Catalão Mine in Brazil. They are predominantly blue apatite, followed by green apatite and, less frequently, yellow apatite. The chemical compositions of these types of apatite were determined by electron microprobe analysis and laser ablation-inductively coupled plasma-mass spectrometry (LA-ICP-MS). Blue and green apatite responded well to the process, thus remaining in the concentrate, while yellow apatite remained in the tailings. Yellow apatite has the lowest phosphorus pentoxide (P2O5 ) content and largest anionic and cationic sites substitution, followed by green apatite, whereas blue apatite is the most homogeneous, with highest phosphorus (P) and calcium (Ca) grades and lowest substitution level.

By Richard A. Levins

The imposition of non-market regulations, such as the proposed SO2 standards for coal combustion, will typically lead to less efficient (thus more costly) production in a free enterprise system. For the coal industry these increased costs will occur in several ways, among which are mining less accessible low sulfur reserves and transporting low sulfur coal to distant markets. There are, of course, social benefits of reducing the S02 emissions from the use of high sulfur coal. The social benefits include decreased health risks, reduced damages to property, and certain unmeasurable benefits associated with the aesthetic appeal of clean air. Proponents of Federal S02 standards argue that the benefits gained from reduced emissions will exceed the costs borne by the coal industry and society in general in meeting the regulations. The purpose of this paper is to investigate the degree to which costs of meeting future energy demands from coal will change under different sulfur standards. No attempt is made to estimate the benefits of imposing regulations. Specifically, the impact of SO2 standards on the private costs of meeting regional coal demands, the competitive positions of the nation's major coal producing regions, the degree to which strip mining as opposed to underground mining will be feasible, the amount of coal being processed, and the amount of coal transported over major rail routes will be analyzed.

Jan 1, 1976

By W. G. Pariseau

A study of coal pillar strength at the Beehive Mine in central Utah was done in the 1970s. This study was a cooperative effort by the University of Utah, RE/SPEC, Inc., and the American Coal Company and was funded by the U.S. Bureau of Mines. Mine measurements of closure at 117 points and pillar stress using 119 vibrating wire stress gauges were made during retreat mining in this room-and-pillar operation. Laboratory testing for the strength and modulus of 372 coal cylinders up 0.3 m (1 ft) in diameter and 0.6 m (2 ft) in length was also done. Two-dimensional finite element model analyses complemented the study. However, the real world of mining is three-dimensional and in consideration of the significant advances in computing power since the time of the original study, a revisit of the data seemed warranted. In this regard, a novel finite element method was used that allows for the whole-mine analysis of tabular excavations on the kilometer scale and yet enables details to be obtained at pillar walls on the meter scale. The effects of material properties variability in situ and of joints can also be taken into account. Results that compare computed two- and three-dimensional seam-level closures with mine measurements show noticeable differences; three-dimensional results are reasonable, while two-dimensional results overestimate closure by nearly a factor of two.

Jan 1, 2014

By S. Daniel Thompson

In underground coal mining, the specification and control of belt and bunker capacities are complicated by (1) stochastic and intermittent conveyor loading, (2) a limited ability to reduce surge at the mine face, and (3) occasional overlapping of loading from two or more mine faces on the conveyors. Recently, because of longwall mining and other factors, the capacity requirements of most mine conveying systems have risen substantially; as a result, efficient capacity design and control have become important mine planning issues. This paper reviews these design issues and their associated modeling procedures. Design considerations and modeling difficulties are also examined.

Jan 1, 1996

By M. Younis, E. Comis

"The success of a tunnel project relies on many factors, but one of the most important is also the most overlooked: coordination by all parties involved during the design stages. This is particularly true of segment design and TBM design. Tunnel lining with segmental rings is usually designed according to the standards of reinforced concrete construction based on a given GBR. However, for TBM tunneling, the determination of loads during ring erection, advance of the TBM, earth pressure, and bedding of the articulated ring are all part of the tunnel lining design as well. TBM design can be heavily affected by the segment arrangement, dimension, and weight, but these are usually given as a fixed input to the TBM manufacturer—a process that can cause unnecessary complications. The authors propose that the industry evaluate the process as it stands. In order to find the optimum balance between lining design and TBM cost and operational workflow, both designs should be finalized concurrently. This requires coordination between the TBM manufacturer and segment designer from the early stages. The aim of this paper is to evaluate the influence of the segment lining design on TBM cost and performance, and to provide commentary on existing design guidelines to optimize lining and TBM procurement. INTRODUCTION The conventional project setup for tunnel lining design and the design and manufacture of the tunnel boring machine (TBM) should be coordinated in a timelier manner. It is widely acknowledged that the design of segments must consider the forces exerted by TBM rams during tunnel construction, but other inputs are most frequently provided to the TBM manufacturer as fixed parameters to design around. This paper describes other important factors in TBM design that impact not only the interaction with the segments, but also the construction of the tunnel in terms of overall production and even safety. For example, the segment width and tapering have direct influence on shield body length and thrust cylinder size. Furthermore, TBM geometry can also affect the backup (trailing gear) layout and length."

Jan 1, 2016

By José Mujica, Mónica Campos, María Fe Campos

The extraction and processing of metals and other minerals have played an important role in economic, political and social development worldwide, from the early stages of prehistory to the present day (Gosner, 2020). Mining has been a fundamental part of human civilization, providing the raw materials necessary for technological, infrastructure and industrial advances. As society progresses, the importance of mining continues to grow, supporting the development of everything from the smallest electronic devices to the tallest skyscrapers (Escamilla, 2024). The economy of a nation is connected to its extractive industries (Moreira and McMahon, 2014), which have seen dramatic growth in recent years (Pietrobelli et al., 2018). In a context of increasing demand for natural resources, driven by the development of emerging technologies, the expansion of infrastructure and the foundation of engineering achievements for the coming decades (Minerals Education Coalition, 2024), mining should focus efforts on global development, requiring a comprehensive approach to sustainability that addresses the planet’s needs and protects the well-being, primarily, of the communities and environments where mining operations take place (Figari, 2024). In these areas, diversity and inclusion should be promoted, thus fostering equitable and sustainable development. The sustainable development goals (SDGs), also known as the global goals, could serve as a key framework for fostering a strong social management culture in mining. The SDGs were adopted by the United Nations (UN) in 2015 as a universal call to end poverty, protect the planet, and ensure that all people enjoy peace and prosperity by 2030 (United Nations Development Programme, n.d.). Companies have compelling reasons to align their actions with the SDGs, as their long-term success depends on healthy communities. This is a major challenge that requires collaborative efforts (Singh and Rahman, 2021). As Fraser (2021) mentions, achieving more sustainable outcomes may involve mining companies and communities working together collaboratively. This article proposes an innovative approach: Inclusive mining for sustainable development, which aims not only to maximize economic profitability but also to promote social and environmental well-being by integrating the UN’s SDGs, primar)ily focused on diversity and inclusion. This can be achieved through the implementation of a key value-added initiative for mining companies: the creation and operation of a corporate volunteering program aimed at developing and executing inclusive practices to promote gender equality, the inclusion of local communities and indigenous peoples, and accessibility for people with disabilities. This proposal will educate employees and stakeholders about sustainability and promote concrete actions through corporate volunteering to strengthen the mining company’s commitment to community development, improve social relations and advance toward achieving the UN’s SDGs, establishing the company as a global change agent.

Nov 1, 2025

By Northcutt Ely

My topic today is our Nation's interest in the minerals beneath the oceans. I will state what I think should be our objectives, the means available to attain these objectives, and the obstacles to their accomplishment. It is possible that as early as this year of 1969 our country must make policy decisions on this subject, and that these, once made, will be almost irreversible. Two factors are hastening an. early decision. First, the 1958 Convention on the Continental Shelf becomes eligible for amendment after June 10, 1969, if the Assembly of the United Nations so decides. Second, the United Nations has created a permanent committee of 42 nations, which was preceded by an ad hoc committee of 35 nations, to study the question of the peaceful uses of the seabed "beyond the limits of national jurisdiction. While these measures purport to deal with the creation of a regime to govern mineral development on the deep sea floor beyond the limits of the jurisdiction of the coastal nations, it has become clear that the urgent issue is the extent to which this future regime shall acquire jurisdiction over the mineral resources of the continental margin, and receive royalties therefrom. This brings the proposal into potential collision with the interests of the coastal nations under the 1958 Convention on the Continental Shelf, including, of course, the United States.

Jan 1, 1969

By Verya Nasri, Jaeseoung Lee, Ashish Bhargava, Shashank Gupta

This paper presents the unique design and construction challenges for the Technoparc Station, located in downtown Montreal as a part of Réseau Express Métropolitain (REM), a light rail rapid transit system. The station is located 15 m below the street with rock-bearing secant pile wall as the primary structural system working as both the retaining and gravity structure. The paper highlights the challenges related to the support of excavation structure, invert slab resisting high hydrostatic forces, waterproofing tightness etc. It also focuses on the importance of Building Information Modeling (BIM) in underground tunneling projects for effective coordination, clash-free, optimized design and costs.

Jun 13, 2021

By J. Korak

Belt conveyor systems, long the standard transportation technique in soft-rock open-pit applications, are encountering growing interest in the hard-rock open-pit sector as economic factors force companies to seek an alternative to costly truck haulage. A general review of mine conveyor systems is followed by detailed analysis of the mobile and semi-mobile in-pit crushing plant essential to successful use of mine conveyors. A final section presents case studies of three crusher-conveyor systems handling overburden, copper ore and granite.

Jan 1, 1985

By M. E. Rossi

In mineral resources, geologic and mining data are acquired, processed, analysed, interpreted and modelled, eventually serving as basis to generate predictions and production plans. This is a complex process, and the resulting predictions are impacted by uncertainties related to the data itself and the processing methods and techniques used. They are also impacted by the subjective decisions made by the modeler(s) at each step of the way. Knowledge, biases, skills, and prior experience come into play in the long mineral resource evaluation development workflow. It is meaningless to discuss uncertainties without evaluating the associated risks that those uncertainties imply. It is important to quantify and assess uncertainty, and to evaluate and mitigate its consequences. This paper discusses (1) conceptual and practical sources of uncertainty; (2) the utopia of an “objective” uncertainty; and (3) the quantification and public reporting of uncertainty using geostatistical conditional simulations. The objective of this paper is to postulate that the industry is running out of reasons and excuses to ignore uncertainty and risk in project evaluation. This is done in two parts, with this, the first one, presenting a more conceptual discussion. Part 2 will present case studies from different types of mining projects and operations showcasing the impact that risk assessments can have in a mining project.

Feb 22, 2026