Search Documents

By D. A. Fenton

Two large 34 ½ foot diameter mills have seen seven years of continuous operation before massive fracturing occurred on one of the trunnion cones. These fractures were discovered when liner changes were made. Four modes of failure were identified, three of the modes combining to cause a large circumferential tear in the 4-inch cone plate. A theoretical account is made of the modes of fracture and comparison made with field results. New material was used to repair the fractured cone, and the complete repair took ten weeks. The repair was monitored and lasted twenty-six weeks before the newly designed structure was available.

Jan 1, 1982

By K. Biswas

In general, it cannot be assumed that the strength of coal pillars remains constant over long time periods. Field observations indicate that a coal seam, especially when it contains a parting layer, deteriorates over time, reducing load-bearing capacity of the pillars. This paper discusses a unique approach to determine the time dependent strength of coal pillars in the field. Three coal pillars that were developed 5, 15 and 50 years ago were chosen for the study. Holes were drilled in coal and parting layers in each pillar and the strength profiles were determined for each hole using the Borehole Penetrometer. The strength data were treated statistically to establish time dependent strength equations for different layers. The results can be used to help estimate the loss of pillar capacity over time.

Jan 1, 1999

By R. L. Loofbourow

The Sunro Copper Mine is near the south coast of Vancouver Island about 35 miles west of Victoria. Failure of the roof of a large open stope let a good sized mountain stream into the mine. Broken are, boulders and sand were washed into the underground mill and out through a 7 800-foot adit. The adit became plugged; water burst out an a ridge above the adit, washing out the portal and o trestle by which it was reached, Rock and ore are strong but several systems of steep, pronounced but generally tight fractures are found on and parallel to the walls of the orebody. The stope was started from a slusher drift 390 feet below the bed of the River and brought up to an elevation 155 feet below the River by blasting vertical and horizontal rings of longholes in the nearly vertical orebody. Mining was stopped there and five months were given to grouting and bolting the pillar under the bed of the River, During this time and for several months thereafter sloughing increased the width, length and height of the stope. At the last known observation the stope was 77 to 96 feet wide, 185 feet long and the highest point of the domed back was only 55 feet below the River. The flooding took no lives. In other respects, however, it might be difficult to find in mining lore o more savage example of the application of "Murphy's Laws".

Jan 1, 1968

By M. Sunkpal, K. C. Kocsis

"An underground environment with high air temperature and humidity conditions generated from various heat and moisture sources can significantly affect the thermoregulation processes of the human body. This can lead to a series of heat-related illnesses such as heat exhaustion, heat cramps and heat stroke. The majority of the metabolic energy of a mine worker results in the production of heat. If the human body is to maintain thermal equilibrium, then this metabolic heat must be transferred to the ambient surroundings at the same rate. The heat loss from the human body occurs through a combination of heat transfer processes, such as respiratory heat exchange, convection, radiation and evaporation. If the heat loss from the human body to the ambient surroundings is less than the metabolic heat produced, the excess will be accumulated within the human body, which will result in a rise in the core and skin temperatures. This can ultimately lead to a heat-related illness or a combination of heat-related illnesses. This paper aims to discuss major heat-related issues and provide an overview of various mine ventilation and cooling systems, which can be employed to overcome high levels of heat and humidity in underground mines. In this paper, the effects of heat exposure on the health, safety and productivity of the mine workers are also highlighted. IntroductionMining in the United States remains one of the most hazardous industries, despite significant reductions in fatal injuries over the last century (Coleman and Kerkering, 2007; Saleh and Cummings 2011; Jacklitsch, Musolin and Kim, 2016). Occupational health hazards within the mining industry include hazards that are physical, such as traumatic injury or hearing loss; chemical, such as silica or diesel particulate matter; biological; ergonomic; and psychological (Donoghue, 2004; Saleh and Cummings, 2011). The effects of some of these hazards can be diagnosed immediately, while many, like black-lung and silicosis, will have long-term effects on the health, safety and life quality of mine workers (Donoghue, 2004; National Institute for Occupational Safety and Health, NIOSH, 2000). Among these hazards, exposure to heat and humidity can significantly affect the safety, health and productivity of mine workers, particularly in deep and hot underground mines (Roghanchi, Sunkpal and Kocsis, 2015). Short-term acute heat exposures can cause a rise in the core temperature of the human body, which can result in a heat-related illness or combination of heat-related illnesses. Adverse long-term chronic heat exposure can generate serious occupational heat-related illnesses, such as cardiovascular diseases, mental health problems and chronic kidney diseases. High core body temperatures coupled with dehydration can generate negative behavioral effects such as physical fatigue, irritability, lethargy, impaired judgment, loss of dexterity and loss of concentration (Xiang et al., 2014)"

Jan 9, 2017

By Dennis K. Mortensen

The warm southwestern desert of Arizona is an ideal location for ASARCO's new Sacaton Unit. The climate of this arid region played a major role in the design considerations of the Unit's crushing and concentrating facilities. Low yearly rainfall and relatively high yearly temperatures are a combination that was taken advantage of when designing the surface facilities. The plantsite, located due west of the mine pit, is in an area originally covered with sparse desert vegetation, underlain to an average depth of 125 feet by desert alluvium. The entire plantsite area slopes gently to the southwest at approximately 1%. Ground conditions at the plantsite area were not acceptable for construction due to the collapsability of the wetted soil when under loaded conditions, Overburden from the pit area was used to form the foundation for the entire plantsite. This waste material, entirely devoid of rock, was placed and compacted to an elevation approximately 20 feet above the desert floor. Elevating the plantsite by filling with waste material not only provided an adequate construction foundation but also eliminated the possibility of flooding from run-off in the surrounding desert areas.

Jan 1, 1974

By ERIK CHARRIER, HUGH MILLER, JOSEF BOURGEOIS

In this study, a unique excavation system was characterized, utilizing waterjet technology as the primary tool for material removal during rehabilitation of reinforced concrete and shotcrete structural liners. Through empiric testing, this research seeks to validate the hypothesis that waterjet removal of these support systems will result in less unintended damage than conventional removal methods. The intent is to develop a viable technology that will reduce the collateral damage caused to surrounding liners during excavation, improve the adhesion between shotcrete and the substrate for longer lasting ground support, and improve overall safety for workers in underground environments. An analysis on the fracture mechanisms and operating parameters of each method was completed. Instrumented shotcrete panels were physically tested and examined through visual inspection and ground penetrating radar (GPR) to compare substrate damage according to each testing method. After testing was completed, the data strongly indicates that waterjet cutting causes less collateral damage to the surrounding intact liner and substrate when compared to that of conventional impact hammers. This research is intended to provide a scientific basis for additional applied research in the rapid excavation and repair of shotcrete support systems.

Sep 23, 2021

By Terry Owen

Not since 1917 has a foreign company developed a standalone, grass roots gold mine in Russia. With Russia's political changes of the late 1980s, development of mineral prospects once again beckons foreign investors. Cyprus Amax's interest in Russia began before the mid-1991 breakup of the former Soviet Union. In 1990, Cyprus Amax began searching for such an opportunity. Early this year, production will begin at the Kubaka gold project located in the Russian Far East, near the Arctic Circle. The Kubaka project is a 1.75-kt/d (1,930-stpd) open-pit operation that will produce more than 9.3 t/a (300,000 oz/year) of gold. Identifying Russian mining opportunities In late 1990, the first Cyprus Amax people travelled to Russia. The trip was to determine the potential for western firms to develop profitable mines. This encouraging visit suggested that Cyprus Amax focus on the Russian Far East with its mineral riches and its easier access to the United States. The company's initial efforts thus focused on working with the Soviet Union's Northeast Geologic Expedition, the then government agency for exploration and geology in Russia's Far East. After the breakup of the Soviet Union, Cyprus Amax continued working with the same people, but they now represented new independent, nongovernmental entities. For three years, Cyprus Amax investigated numerous deposits. This resulted in the identification of two properties of significant interest, one of which was Kubaka. Location Kubaka is located in the Northern Evensk District of the Magadan Oblast in the Russian Far East. This is an area east of Siberia. The project is situated in a mountainous area of the Kolyma Range, about 300 km (985 miles) south of the Arctic Circle. It is 285 km (180 miles) north of the fishing village of Evensk and 380 km (235 miles) northeast of the silver-mining town Omsukchan. The site is 950 km (590 miles) northeast of the regional capital city of Magadan. Magadan, the political and economic center of the Oblast, has a population of about 150,000 people. It is served by a year-round deep-water port (with icebreaker assist) and an international airport with service to Moscow and Anchorage, AK. Access to the Magadan region

Jan 1, 1997

By Prakash Venkatesan, Mehmet Ali Recai Ӧnal, Shaik Saida, Veerendra Singh, Chenna Rao Borra, Manish Kumar Kar

A laboratory-scale investigation of the effect of milling operation and catalyst addition ( K2CO3) on the partial reduction of low-grade pyrolusite ore pellets was carried out using coke as a reductant. Thermogravimetric analysis was used to understand the correlation between milling and catalyst addition parameters with the reduction temperatures. DTG analysis of pyrolusite pellet reduction showed three distinctive peaks associated with a three-step reduction mechanism (i.e., MnO2→ Mn2O3→Mn3O4→MnO). The results showed that the grinding and addition of the catalyst have a significant effect on lowering the MnO2 reduction temperature independently. But maximum reduction temperature drop is obtained when combining grinding and catalyst addition in this work. By 3 h milling and 10 wt% catalyst addition, the reduction temperatures were reduced by more than 200 °C compared to the raw ore pellets. These results obtained from the DTG analysis were further supported by XRD analysis of the reduced samples.

Dec 20, 2022

By Adrian C. Dorenfeld

Concentradora "Dana Aida" (100 t/d capacity) was built in 1971-1972 to treat dumps and ores containing mixed oxide-sulfide copper-gold-silver minerals from two veins. The veins, Don Felipe and aria are about 150 m apart, but are distinctly different mineralogically. The deposit is near San Juan de Guadalupe, Durango. Mexico. All new process equipment was manufactured locally, in or near Torreon, Coahuila. Sampling, ore testing, flowsheet design, plant design, drawings purchasing, financing, etc. was planned and directed by two engineers. Construction was executed by local miners and common labor (largely agricultural). The paper presents detailed costs for equipment and construction. The subsequent breaking-in operation is discussed.

Jan 1, 1979

By Peter G. Dunn

Geologic studies during development at Copper Flat were directed at acquiring the information necessary in evaluating a low-grade porphyry copper deposit. In addition to the geologic mapping and core-logging of a typical exploration project, these studies included the following : (1) careful checks on the sampling and assaying (2) selection of representative samples used to establish the recoverable amounts of precious metals in the ore (3) examination of underground workings driven to provide samples both for metallurgical testing and for assay comparisons (4) evaluation of plant site and waste dump areas as non-mineral, including a placer examination of the taillngs disposal area (5) location of an adequate water supply. All these investigations were carefully documented to provide the necessary data both for the engineering design and, more importantly, for the feasibility studies required for successfully financing the project.

Jan 1, 1981

By D. Robert Weir, Verner B. Sefton

The reduction roast-ammonium carbonate leach-hydrogen reduction process for laterites has been under development by Sherritt Gordon for the past 20 years. The process can treat high iron or low iron laterites, with some process modification, and gives extractions of 88-93% Ni or 82-88% Ni, respectively. Five campaigns on a 1 tonne per day Pilot Plant and four campaigns on a 35 t/d Demonstration Plant have been carried out on laterite from three different deposits, and many other laterites have been investigated in the laboratory. The Marinduque Surigao Nickel Refinery in the Philippines was designed on the basis of this work. The process comprises roasting to selectively reduce the nickel and cobalt in the laterite, leaching the calcine in ammonium carbonate to dissolve the metals, recovery of cobalt by precipitation of a mixed metal sulphide, concentration of nickel from the carbonate solution by basic nickel carbonate precipitation and recovery of high purity nickel by hydrogen reduction of nickel from ammonium sulphate solution. Ion exchange has been developed as an alternative to BNC and for recovery of trace nickel from BNC barren liquor. Details of the development of some of the process steps through the laboratory to commercial plant are discussed. The process metallurgy has been confirmed in the commercial plant.

Jan 1, 1979

By William C. Peters

The Alpine-Himalayan system, the only major active tectonic belt mainly exposed in a continental mass, is of increasing interest to exploration geologists as well as to theoreticians. Answers to the broader problems of plate tectonics are being sought in this intricate system where the geosynclinal concept was born and where the geotectonic cycle was first applied to metallogeny. The search is all the more intense because it involves scientists from more than a dozen countries with a stimulating variety in perspective. The international Geodynamics Project has allocated the Alpine-Himalayan system to two separate study groups with one directing its attention to the Alpine-Mediterranean region and the other giving consideration to the Himalayan region. This geographic division is accepted in this paper, with remarks being confined to the former and to the west of boundary zone between the European-Asian and the Southeast Asian plates as envisioned by Dewey and Bird (1970). The region is well-mapped in some parts and it includes some of the most intensely-studied geology, most classic mines, and newest orebody discoveries. Within the region, an Alpine-age copper-molybdenum metallogenic belt extends from Rumania to Pakistan. The belt can be considered in terms of plate tectonics, and there is the possibility of using plate tectonics concepts in exploration.

Jan 1, 1973

By Peter Schmäh, Tobias Engel

The E-Power Pipe technology was originally developed for the trenchless installation of protective pipes and pipelines of 10" to 28" diameter, over long distances of more than 4,000 ft. The twostage process combines elements from Horizontal Directional Drilling (HDD) and microtunnelling technology. A microtunnelling boring machine (MTBM) excavates the borehole using a specially designed, temporary jacking pipe. A Rack & Pinion jacking frame pushes the equipment during the pilot bore and pulls in the prefabricated pipe string in a second step. The slurry microtunnelling machine is equipped with a jet pump, creating the so-called AVNS machine type. A new generation of small hard rock cutting wheels complements this considerable achievement for the tunnelling industry

Dec 1, 2022

By W. D. Bullock

The King-Beaver mine of Asbestos Corporation Limited operates an open pit in the city of Thetford Mines, Quebec. The approximate loca-tion of the open pit is at Latitude 46° 02' North and Longitude 71° 20' West. The general topography is 1020 feet above sea level. Thirty-six percent of the company's scheduled asbestos ore production, for the Thetford Mines area, comes from the King-Beaver pit. The pit operates 24 hours a day, six days a week. Normal production is 10,500 tons of ore per day at a waste to ore ratio of 2 to 1. The remaining ore requirements are mined from the King-Beaver underground mine and the British-Canadian mine.

Jan 1, 1980

By M. Bai

The influence of mining on the hydro-geomechanical environment is greatly constrained by alternating mining geometries. The limiting magnitudes of surface subsidence and groundwater flow over the mining area, as a result of geometry changes, can be reasonably predicted through a coupled finite-element model introduced in this paper. Verification of the model has been tested using real and conceptual case studies which reveal that changes in strata conductivities are strongly related to the strata deformation induced by mining. The greatest modification of hydraulic conductivities occurs within the caving or severely fractured zones. The study indicates that narrowing the panel face width will substantially reduce both the intensity and extent of mining damage to the overlying strata, limit surface subsidence and constrain the change in hydraulic conductivity to a reduced scale and smaller extent, particularly as mining depth increases.

Jan 1, 1993

By G. R. Hart

The expected 1990 Clean Air legislation is providing electric utilities with a series of challenges and decisions as the utilities prepare strategies to comply with the resulting regulations. This paper addresses the strategy development of a coal-based utility --the legislation, the process used, the fuel issues, the options available, and the decisions to be made.

Jan 1, 1991

By Chuang Sun, Feng Luo, Guo‑dong Li, Xue‑qing Li, Tuan He

The mining-induced failure of the coal seam floor is essential for water inrush. The mining disturbance to the floor, especially in the thick coal seam, is severe, and the water inrush risk is also higher than that in regular thick coal seam excavation. The superposition of many stresses, including in situ stress, mining-induced stress, and confined water pressure, must be considered in the prediction of the floor failure depth. This study adopted the elasticity analysis, FLAC3D numerical simulation, and on-site acoustic wave test comprehensively. The thick coal seam working face of the Zhong-Yu coal mine affected by confined water was selected as the engineering background to study the characteristics of the floor failure. Based on elastic foundation theory and the superposition principle, the mechanical model and the failure depth criterion of the floor were established, respectively. The distribution and evolution of mining-induced stress and the plastic zone in surrounding rock during the mining process are obtained by FLAC3D. In addition, the changes in the P-wave wave velocity in the floor before and after mining were compared and studied by the acoustic wave test method. The range of floor damage depth is determined on the basis of the above research.

Jun 8, 2022

By Michael S. Moats, John Bailey Fletcher

The performance of grinding media can be misrepresented in marked ball wear tests due to galvanic interactions between dissimilar media. The possible galvanic interaction of media materials during marked ball wear tests has not been adequately explored. Corrosion rates and potentials of modern high carbon steel and high chromium white iron grinding media materials were measured using electrochemical testing as a function of pH and chloride content in a simulated mill water. The results replicate previous research with the high chromium white iron sample being more noble (higher corrosion potential) and corrosion resistant (small corrosion current) than high carbon steel. Using the experimental data and corrosion theory, the effects of galvanic coupling on corrosion rates were calculated to examine what could happen during a marked ball wear test or when a mixed media charge is present. This analysis indicates that high carbon steel can cathodically protect high chromium white iron leading to significant decreases in the corrosion rate (up to 99%) of this material during marked ball wear tests. The magnitude of the protection is a function of the pH of the mill water.

Dec 21, 2022

By Zohreh Kazemi Motlagh, Virginia T. McLemore

There are more than 15,000 abandoned mine features in New Mexico. A considerable number of these mines have not been cataloged or assessed for prioritized reclamation efforts. These mine wastes can be examined as a resource of critical minerals. Many of legacy mine waste deposits have undiscovered commodities and critical minerals, due to low recovery processes during past production. In this project, Black Hawk mine wastes in Grant County, New Mexico are examined by thorough mineralogical and geochemical characterization. This project seeks to characterize and estimate the critical minerals in mine wastes of Black Hawk mine, and determine the acid generating potential of mine waste. Identifying and producing critical minerals in New Mexico may directly benefit the U.S economy and national security.

Feb 1, 2024

By Joel K. Waterland

GENERAL DESCRIPTION Homestake Mining Co.'s operations are at Lead, SD. Production from the various methods used are: 1 155 753 t/a (1,274,000 stpy) by open cut-and-fill, 68 039 t/a (75,000 stpy) by square set cut-and-fill, 144242 t/a (159,000 stpy) by shrinkage stoping, 107 048 t/ a (118,000 stpy) by blasthole stoping, and 67 132 t/a (74,000 stpy) in development work for a total of 1 542 214 t/a (1,700,000 stpy). Mining takes place from the 616-m (2000-ft) level to the 2073-m (6800 ft) level (Fig. 1). The average travel time to the stope is 45 min. GENERAL ORE BODY REQUIREMENTS AND LIMITATIONS Size, Shape, and Dip of Ore Body Six major ledges varying from 914 m (3000 ft) long by 228.6 m (750 ft) wide to 305 m (1000 ft) long by 122 m (400 ft) wide are mined. Within these ledges are irregular-shaped areas of varying sizes. These ledges dip at approximately 1.2 rad (70°) to the east and plunge to the south from 0.26 to 1.57 rad (15° to 90°). Ground Conditions The ore is cummingtonite (chlorite schist) which is very competent except for major bedding planes and fracture patterns. The footwall is a slate but because of the dip presents very few problems. The hanging wall is also a slate which because of the dip and bedding is very weak and requires considerable rockbolting. No problem has been encountered with rock bursts to a depth of 2438 m (8000 ft). Ore Value The ore values vary somewhat from ledge to ledge, but the average ore delivered to the mill is approxi¬mately 6.2 g (0.2 oz) of gold per ton. A small amount of silver is the only byproduct of this operation. Annual production of gold is approximately 10 575 183 g (340,000 troy oz). Production Requirements The mine has a mill capacity of approximately 1 723 651 t (1,900,000 st) but because of several fac¬tors (manpower, depth, etc.) this mill capacity has not been attainable for the past several years.

Jan 1, 1982