Search Documents

By Alan R. Johnson

Because of the competitive nature of the iron ore pelletizing industry, commodities required for the production of pellets are continually being scrutinized to minimize their usage and offset rapidly escalating costs. In the Tilden pellet plant, the usage of one commodity, bentonite, has been reduced from over twenty-four pounds per long ton of pellets to as low as eight pounds per long ton. The evolution of bentonite usage from plant start-up to the present time is described.

Jan 1, 1984

By Robin J. Hickson

The Ortiz Mine is operated by Gold Fields Mining Corporation, a subsidiary of Consolidated Gold Fields Ltd., one of the world's major gold producers. The Ortiz Mine is Gold Fields only heap leaching facility as well as being their first operating mine in the U.S.A. The hydrometallurgical processes utilized for recovery of gold and silver at Ortiz are discussed along with the several practical changes in operation adopted since start-up. Included are heap leaching by cyanidation, concentration of values on activated carbon, desorption, and the final electrowinning steps prior to shipment. Construction costs and pertinent technical data are shown.

Jan 1, 1981

By Chao Zhang, Wenhao Xia, Jianxin Fu, Ling Yu, Weidong Song, Yang Li

Sanshandao Gold Mine is the only undersea metal mine in China. To deal with the collapse and pumping of stopes and roadways caused by complex ore-rock occurrence conditions, the mine conducts filling and sealing of some areas, and the remaining ore reserves will be mined after treatment. Therefore, it is urgent to evaluate the stability of rock masses, fault fracture zones, and aquicludes during the secondary mining process. In this study, displacement and microseismic methods are employed to monitor rock deformation and fractures. Additionally, FLAC3D was used to simulate the process of secondary mining, reproducing the evolution of stress fields, displacement fields, seepage fields, and plastic zones at different mining stages. The combination of numerical simulation and on-site monitoring verification demonstrates that the deformation of surrounding rock presents a rapid growth at the initial stage of mining, followed by a gradual decrease in the growth rate, and finally tends to stabilize; the fracture zone area at the 151–159 exploration line on the − 320 m level (near the 7# and 8# stopes) exhibits poor stability, and monitoring measures should be strengthened; the deformation value of the aquiclude is less than the deformation value of I protection level in the Code for Design, the impact of secondary mining on the aquiclude is limited; fault and fracture zone deteriorate rock mass stability, and their impact is related to their spatial locations. Hanging wall fault has a more significant impact on the settlement of the aquiclude, while the footwall fracture zone has a greater impact on the development of the plastic zone.

Feb 21, 2024

By P. C. Thakur

The productivity in coal mines, measured in terns of the output per manshift depends largely on the efficiency and speed of men and materials transport between working faces and the surface. The mechanization of coal winning and material handling processes has led to a great rise in the mine productivity (1). Early applications of power in U. S. coal mines were mainly electrical. The excellent traction available with the DC motor and the ease of the distribution of the DC power have made trolley wire installations for haulage very popular. In shallow mines with very limited emissions of methane it did not constitute a major hazard but as mine depths increased and corresponding emissions of methane also increased fire and methane ignition hazards have become very serious. Conveyors have proved economic where intense mechanization of coal faces generates a large output of coal from a single face, but the fire and respirable dust hazard associated with them are no less serious. Recognizing these shortcomings, the Federal Coal Mine Health and Safety Act of 1969 laid down numerous provisions for the safe use of trolley-wire haulage and conveyors (2) which generally improve safety but in some cases complicate mining operations and have decreased productivity significantly since 1969. In course of time as coal mines become deeper and hence gassier and as the emphasis on safety increases it would be inconceivable to use trolley-wire haulage under ground as already witnessed in several other countries with deep coal mines. With rising capital investments and cost of the protection against fire and respirable dust, the use of conveyors may also have to be limited to special areas, e.g. main entries. Indeed, there are only two alternatives available, namely; (1) Degasify the coal seams prior to mining and use conventional electrical power, or (2) Develop alternate sources of power which would be safer and yet efficient and cheap.

Jan 1, 1975

By Graham Jones

During 1982 Ash Grove Cement Company contracted with Wagester, Walker, Thornton & Company to convert a Calcimatic rotating hearth kiln at its Portland, Oregon lime plant from gas/oil to coal firing. Increasing costs of natural gas and No. 6 fuel oil made this conversion mandatory if the plant was to remain competitive. Unique features of this project are 1) the distributors of pulverized coal to eighteen small burners around the inner and outer perimeters of the doughnut-shaped kiln, and 2) the attrition-dryer-pulverizer mill. Ash Grove, a century-old lime and cement producer headquartered in Overland Park, Kansas (Kansas City area), looked at various schemes for multiple burner firing before employing Wagester, Walker, Thornton & Company. W.W.T. of Pitts- burgh, Pennsylvania was formed in 1980 by acquiring the Solid Fuels Division of the Pullman Swindell Corporation. This division had been active in developing solid fuel firing for brick tunnel kilns, principally in the Southeast. They continue to supply such systems firing wood waste as well as coal to the brick industry and have also converted two Calcimatic lime kilns for Dixie Lime, Sumterville, Florida, a fluid bed calciner for Texas Gulf in Aurora, North Carolina, and a chrome concentrate kiln for Diamond Chemicals at Castle Hayne, North Carolina. Testing and a proposal have been made for INMETCO, Elwood City, Pennsylvania, on an annular hearth furnace for direct reduction of iron ore to metallic iron.

Jan 1, 1984

By Andrea B. Baldwin

In recent years, federal and state regulatory agencies have tightened air emission standards. Two of the acid gases, hydrochloric acid (HCI) and sulfur dioxide (SO2), are under heavy scrutiny for reduction. . Most traditional scrubbing systems, i.e. wet scrubbers and spray dryers, meet the standards but they typically are high in capital cost, have significant space requirements for equipment, and are difficult to maintain. Dry sodium injection (DSI) is a alternative technology that has been shown to be effective in HCl and SO2 removal while being the inverse to the problems listed with traditional systems. This paper covers the mechanics of dry injection scrubbing using the most effective sorbents, sodium bicarbonate and mechanically-refined trona (natural sodium sesquicarbonate). It presents DSI performance data for Chambers Medical located in Hampton, SC. This facility incinerates local medical and municipal solid waste. Chambers Medical has used mechanically-fined trona for HCl and SO2 removal since late 1991.

Jan 1, 1995

By Hongwei Wang, PEIPEI CAO, Yongping Wu, JIANQIANG JIAO

In the fully mechanized top caving mining of steeply inclined, extra-thick seams with variable angles, the mechanisms of roof rock movement, failure, caving and filling are highly complex. This is due to the varying angle of coal seam in different areas, which makes rock–equipment stability control challenging. In this paper, the surrounding rock deformation and failure mechanisms, bearing structure of the overburden, and working characteristics of the supports are elucidated. The principle and key technologies of rock–equipment stability control are presented and applied to control the overburden of the regional failure and realize safe and efficient mining of the working face.

By E. Yigit

Hydrometallurgical production of zinc from concentrates is generally carried out by H2SO4 leaching. For the smooth operation of this process, some harmful components must be removed from the leach solution before the electrolysis stage; MgO is one of these compounds. Zinc concentrate samples from the Mount Isa mines were used in leaching tests. Leaching tests with an aqueous solution of H2SO4 and SO2 gas were carried out at various temperatures, pH levels and leaching durations. While duration and the pH value of the solution were effective parameters in H2SO4 leaching, temperature and pH were more effective in SO2 leaching for the removal of MgCO3 and CaCO3. Removal of MgCO3 and CaCO3 was generally achieved at low pH values. The results show that SO2 gas can be a good alternative to sulfuric acid in the leaching of MgCO3 and CaCO3

Jan 1, 2010

By Shinzaburo Kato

In 1977 Kawasaki Steel Corporation (KSC) built No. 6 BF (Blast Furnace) with an inner volume of 4 500m3 as part of our program to produce 8.5 million tons of crude steel a year at Chiba Works. As the primary raw material to be used in No. 6 BF, we decided to use sintered ore, because we were confident in the obvious advantages of our technology developed by that time on sintering and BF operation using sintered ore. At Chiba Works, however, we had no space for the construction of a sinter plant, so we decided to build it abroad. Sintered ore is easily crushed and degradated. Producing sintered ore at a point far away from the blast furnace and transporting it across the ocean was the world's first attempt. To successfully realize it, we conducted a series of fundamental surveys and studies with special stress on the real aspects of degradation of sintered ore caused by long-distance transportation and handling and the ways and means to prevent the degradation. As a result, we decided to build a plant on the Mindanao of the Philippines.

Jan 1, 1982

By L. Barry Phelps

The application of an open-pit Materials Handling Simulator (OPMHS) to analyze mine planning and scheduling problems in large surface mines is discussed. The mine chosen for this application employed a large stripping dragline working in tandem with a shovel-truck haulback system for removing overburden. Large bottom-dump trucks were employed behind a coal loading shovel to transport the exposed coal out of the pit. Specifically, the current operations and the recommendations for short term and long term improvements were simulated on OPMHS. The effects of changing the operating parameters of the equipment on the total system were evaluated. Several alternatives were also studied for the best use of the existing equipment if the current operating parameters could not be improved upon. The results of the application are discussed.

Jan 1, 1978

By Harry Perry

U. S. consumption of sulfur and sulfur products is expected to increase at a rate of 8 percent per year between now and 1980, largely as a result of their use in fertilizer markets. World consumption is also increasing rapidly, but at a-lower rate, about 6-percent per year. In 1965, sulfur recovered in the United States from purification of natural gas; nearly doubled from the 1956-1960 average; production from pyrites declined; and production of elemental sulfur increased 15 percent. Concern about air pollution resulting from sulfur oxides produced from the combustion of fossil fuel has lead to intensive research on methods of removal before combustion, during combustion (in-process methods), and from the resulting flue gases. If all the sulfur in fossill fuels were recovered, more sulfur products would be produced than were consumed in the United States in 1965. Removal of sulfur from coal before combustion could result in a product sufficiently-high in sulfur to be a suitable raw material for sulfuric acid manufacture. In-process methods produce solid sulfates, some of which may have commercial value. Flue gas removal' methods for sulfur oxidest generally result in the production of a byproduct either of sulfuric acid or sulfur. The projected sale of these materials significantly lowers the anticipated cost of sulfur dioxides pollution abatement. Alternate methods for sulfur dioxide reduction are discussed. The various proposed processes are described and costs are given for the various methods for which estimates have been made.

Jan 1, 1967

By R. V. Ramani

Demands on available lands will continue to increase due to the projected increase in population and industrial expansion. Though there is an upper limit on the available lands, the multi-use nature of the lands will make it possible to meet these demands. However, this will not happen without adequate planning. Land uses can be broadly categorized as non-renewable and renewable. Lands with mineable resources can be dedicated at some point in time to the extraction of resources. Such a dedication, however long-term, is only temporary because of the non-renewable nature of the mineable resources. Implied here is that the land will be available before and after mining for other uses. Planning for such lands must have the objective that, as far as practicable, no non-renewable uses are pre-empted and no renewable uses are permanently destroyed. The primary aspects of this planning process will be addressed in this paper, These aspects include a discussion of planning responsibility, data needs and availability, the integration of mine planning and post-mining land use planning and a long-term plan for resource conservation and utilization. Minerals, together with agriculture and forestry products, are the primary sources of wealth. Therefore, to avoid land development that may pre-empt future mineral resource utilization, the local planning groups must be aware of the mineralization and mining potential. Much work needs to be done to identify and characterize the mineral resources. Even more work is needed in land use planning for lands with mineral deposits.

Jan 1, 1982

By Yingbao Yang, Jinyue Liu, Yonggang Wei, Bo Li

Due to the depletion of copper ore with high-grade and low impurity contents, the raw materials for copper smelting exhibit low copper contents and high impurities. High-impurity elements lead to the poor performance of the final copper product; thus, the removal of impurity elements during the oxygen-enriched copper smelting process is crucial. In this study, based on the production of high-grade matte, the occurrence states of impurity elements (such as As, Pb, and Zn) are analyzed in the input and output materials of the oxygen-enriched smelting process, and the phase transformation mechanisms of impurity elements are revealed during the oxygen-enriched smelting process. The effects of temperature, Fe/SiO2 ratio and oxygen concentration on the distribution behaviors of impurity elements in dust, slag and matte and the removal rates of impurity elements in matte are clarified. The results show that the impurity elements mainly exist as As4, As4S4, As2O3, Pb, PbS, PbO, Zn and ZnS in dust, as FeAsO4, As2O3, FeAsS, PbSiO3, Zn2SiO4 and ZnFe2O4 in slag, and as As, FeAsS, PbS, PbO and ZnS in matte. High smelting temperature, low Fe/SiO2 ratio and low oxygen concentration are beneficial for improving the matte grade and the removal rates of impurity elements Pb and Zn in matte. Low smelting temperature, low Fe/SiO2 ratio and high oxygen concentration are beneficial for removing impurity element As in matte.

Aug 8, 2023

By E. E. Malouf

For centuries small amounts of copper have been recovered from acid mine-drainage waters. In recent years, the expansion of copper-bearing waste dump leaching for copper recovery has established a technological basis that is rapidly converting the art of copper leaching' into a science. Leaching of copper, whether from copper-bearing ore or waste, follows well established chemical reactions. These reactions are commonly in an acid circuit, but where leaching of copper is to be made in rock that is a high acid consumer, ammonia and ammonia carbonate, as well as cyanide leach solutions, can be used effectively. Current hydrometallurgical processes are being applied at an ever increasing rate to recover the trace amounts of copper in copper mine waste by in-place leaching. Currently approximately 300, 000 tons of copper are produced annually in this manner where as recently as ten years ago, only one-eighth of this amount of precipitate copper was produced.. Where copper occurs as an oxide in higher concentrations as to be classified as an ore rather than waste, then the hydro-metallurgical processes are applied as percolation or agitation leaching in vats, pachuca tanks, or prepared heaps. This approach gives better control over the recovery of the leach solutions, particularly in the processes where ammonia or cyanide leaching agents are to be used.

Jan 1, 1972

By F. C. Appleyard

As one of the more important Industrials Minerals, gypsum occupies a significant place in the economy of the United States, particularly in that segment which can be loosely called the Construction Industry. For many years, products made from gypsum have been a major building material, and the usefulness and versatility of these products is such that their widespread use is expected to continue. In 1968, according to U.S. Bureau of Mines statistics, the value of all gypsum products sold in the United States was 405,000,000 - and although this value has dipped from the 1964 high of $ 432,000,000, it is expected to trend upward in the next few years to equal and surpass this figure as the construction industry recovers from its current squeeze of "tight money" and high interest rates. There are many factors to be measured in determining the potential value of any mineral deposit, and how it might fit within its particular industry. What, then, are the qualities which a gypsum deposit must have in order to profitably participate in the four hundred million dollar plus business which is the gypsum industry? First let's consider the geology of gypsum, the geographic distribution of deposits, and the more important factors such as size, grade, capital requirements, and operating cost. Then, an understanding of the uses of gypsum, various types of products, and location of markets would be helpful, along with such other factors as the structure of the industry, price trends, etc.

Jan 1, 1970

By J. Drelich

An improved experimental procedure to measure contact angle has been consolidated with coal surface preparation involving polishing with abrasive paper, alumina powder, and a cloth, followed by ultrasonic and mechanical cleaning. Specifically, the captive-bubble measuring technique has been compared with the sessile-drop technique and the former has been recommended for the examination of the hydrophobic properties of coal surfaces. Results of the research program, which is currently under way, on the examination of the effect of the nature, amount, size and distribution of mineral inclusions in coal on its wettability are briefly reviewed.

Jan 1, 1999

By James L. Evers

The development of hydraulic mining in the United States has had an uneven record of progress. The shifting of coal extraction from one government agency to another has not provided an environment for a focused national research program. This paper presents an update on hydraulic mining research in the United States. A comparison is made between the development of the technology in this country and the state of the art in other parts of the world.

Jan 1, 1983

By T. C. Page, P. C. Gibson, M. A. Miller, J. D. Sell

[The Yarnell gold deposit in the Weaver mining district, Yavapai County, Arizona, occurs in a structurally controlled, hydrothermally altered zone in a 1700 Ma granodioritic intrusive. Both potassic and sericitically altered rocks around and above the low-angle, northeast striking Yarnell fault are known to host economic gold mineralization. A wider envelope of weakly-propylitic altered rock also occurs in this area. During mineralization, strong sericitization accompanied several stages of quartz (±adularia) veining, stockwork formation, localized silicification and potassic replacement, in association with deposition of specularite, pyrite (now oxidized) and gold. The footwall of the fault is also sericitically altered but poorly mineralized. Mineralization along the Yarnell fault continues both northeast and southwest from the main deposit, although the thickness of the zone and associated alter avian envelope diminish away from the orebody A sample of undo formed illite taken from the Yarnell fault zone was K/Ar dated at 69 + 1.6 Ma. This date reflects a minimum age for both mineralization and latest movement on the fault. Gold mineralization is accompanied by modest increases in Ag, As. Cu and Mo content. Both CO2- and H2O- rich fluid inclusions were studied and suggest mesothermal pressures and temperatures of formation for the deposit. Ninety-six reverse circulation holes and four diamond drill holes outline a bulk-minable mineral reserve of'4.1 million tons at 0.051 oz of Au per ton. An additional 2.7 million tons at 0.017 oz of Au per ton occurs in a low-grade zone above and subparallel to the main mineralized zone. Total calculated mineral inventory stands at 6.8 million tons at a grade of 0.038 oz of Au per ton, with a waste-to-ore ratio of 1.45:1. Column leach tests indicate that cyanide heap leach gold recoveries should exceed 70%.]

Jan 1, 1994

By Yousef Ghorbani, Abolfazl Danesh, Fatemeh Kazemi, Ataallah Bahrami, Morteza Abdollahi

The abstract highlights the impact of flocculants used in the middle thickener of a copper-molybdenum plant on both process water quality and molybdenite floatability. The study investigates the effect of a starch-based flocculant (wheat starch) on the efficiency of the middle thickener and molybdenite flotation. The findings indicate that the presence of starch influences the settling behavior of particles with different shapes, and the dosage of starch affects both molybdenum recovery and the presence of copper minerals in the molybdenum concentrate.

Mar 7, 2022

By S. Natansohn

A prevalent technique for the recovery of silver from wastes generated in silver-tungsten electrical contact fabrication is electrowinning. Such scrap is placed in a permeable plastic basket which constitutes the anode compartment and this basket is suspended in a larger cell in which the cathode is mounted. A silver nitrate solution is used as the electrolyte and, upon application of an electric field, the silver migrates to the cathode where it deposits out. At times, there is tungsten migration to the cathode compartment and consequent co-deposition with the silver. This W contamination, which may amount to several thousand ppm, necessitates additional purification of the deposited Ag and its removal would therefore be advantageous. The elimination of the W impurity would also extend the operating period of the cell with corresponding increase in the Ag output and savings in labor costs.

Jan 1, 1982